Tektronix WFM2300 Manual

WFM2300 and WFM2200A
Multiformat Multistandard Portable Waveform
Monitors
Installation and Safety Instructions
*P071320502*
071-3205-02

WFM2300 and WFM2200A
Multiformat Multistandard Portable Waveform
Monitors
Installation and Safety Instructions
www.tektronix.com
071-3205-02
This document supports software
version 2.11.x and above.
Revision A

Copyright © Tektronix. All rights reserved. Licensed software products are
owned by Tektronix or its subsidiaries or suppliers, and are protected by
national copyright laws and international treaty provisions. Tektronix products
are covered by U.S. and foreign patents, issued and pending. Information in this
publication supersedes that in all previously published material. Specifications
and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
■In North America, call 1-800-833-9200.
■Worldwide, visit www.tektronix.com to find contacts in your area.

Table of Contents
Important safety information .............................................................. iii
General safety summary ............................................................... iii
Service safety summary ................................................................. v
Terms in the manual ....................................................................... v
Symbols on the product ................................................................. vi
Compliance Information .................................................................... vii
EMC compliance ......................................................................... vii
Environmental compliance ......................................................... viii
Preface ................................................................................................ xi
Accessories .................................................................................. xii
International power cords ............................................................ xii
Optional accessories ................................................................... xiii
Instrument options ...................................................................... xiii
3G .......................................................................................... xiii
ASI ........................................................................................ xiii
AVDP .................................................................................... xiii
DATA .................................................................................... xiv
DBE ....................................................................................... xiv
LOUD .................................................................................... xiv
SFP ........................................................................................ xiv
SFP-HDMI ............................................................................ xiv
Documentation ............................................................................ xiv
Operating requirements
Electrical ratings ............................................................................. 1
Power requirements .................................................................. 1
AC power ................................................................................. 1
Battery power ........................................................................... 3
Environmental ratings .................................................................... 4
Physical specifications ................................................................... 5
Cleaning .................................................................................... 5
WFM2300 and WFM2200A Installation and Safety Instructions i

Installation
Connectors ...................................................................................... 7
Power cord installation ................................................................. 10
Battery pack installation ............................................................... 11
Battery charge level indicators ............................................... 14
Tripod installation ........................................................................ 15
SFP module installation ............................................................... 16
SFP module removal .............................................................. 17
SFP module transportation ..................................................... 17
Video system installation ............................................................. 18
Line termination ..................................................................... 18
Compatibility of BNC center pins .......................................... 18
To monitor the video bit stream of a serial receiver ............... 19
To monitor the embedded audio signal in a serial digital video
stream ................................................................................ 19
To monitor the external reference signal ................................ 20
To genlock the SDI output signal to the external reference
signal ................................................................................. 20
To test cable margins .............................................................. 20
To measure A/V delay or propagation time (Option AVDP
only) .................................................................................. 21
Power-on and power-off procedures
Power-on ...................................................................................... 23
Power-off ...................................................................................... 23
Front panel controls
Layout and usage .......................................................................... 25
Three levels of control ................................................................. 29
Scope of controls .......................................................................... 29
Table of Contents
ii WFM2300 and WFM2200A Installation and Safety Instructions

Important safety information
This manual contains information and warnings that must be followed
by the user for safe operation and to keep the product in a safe
condition.
To safely perform service on this product, see the Service safety
summary that follows the General safety summary.
General safety summary
Use the product only as specified. Review the following safety
precautions to avoid injury and prevent damage to this product or any
products connected to it. Carefully read all instructions. Retain these
instructions for future reference.
Comply with local and national safety codes.
For correct and safe operation of the product, it is essential that you
follow generally accepted safety procedures in addition to the safety
precautions specified in this manual.
The product is designed to be used by trained personnel only.
Only qualified personnel who are aware of the hazards involved should
remove the cover for repair, maintenance, or adjustment.
Before use, always check the product with a known source to be sure it
is operating correctly.
While using this product, you may need to access other parts of a larger
system. Read the safety sections of the other component manuals for
warnings and cautions related to operating the system.
When incorporating this equipment into a system, the safety of that
system is the responsibility of the assembler of the system.
To avoid fire or personal injury
Use proper power cord. Use only the power cord specified for this
product and certified for the country of use. Do not use the provided
power cord for other products.
WFM2300 and WFM2200A Installation and Safety Instructions iii

Power disconnect. The power cord disconnects the product from the
power source. See instructions for the location. Do not position the
equipment so that it is difficult to operate the power cord; it must
remain accessible to the user at all times to allow for quick
disconnection if needed.
Use proper AC adapter. Use only the AC adapter specified for this
product.
Do not operate without covers. Do not operate this product with covers or
panels removed, or with the case open.
Do not operate with suspected failures. If you suspect that there is damage
to this product, have it inspected by qualified service personnel.
Disable the product if it is damaged. Do not use the product if it is
damaged or operates incorrectly. If in doubt about safety of the
product, turn it off and disconnect the power cord. Clearly mark the
product to prevent its further operation.
Examine the exterior of the product before you use it. Look for cracks
or missing pieces.
Use only specified replacement parts.
Replace batteries properly. Replace batteries only with the specified type
and rating.
Recharge batteries properly. Recharge batteries for the recommended
charge cycle only.
Do not operate in wet/damp conditions. Be aware that condensation may
occur if a unit is moved from a cold to a warm environment.
Do not operate in an explosive atmosphere.
Keep product surfaces clean and dry. Remove the input signals before
you clean the product.
Provide proper ventilation. Refer to the manual's installation instructions
for details on installing the product so it has proper ventilation.
Slots and openings are provided for ventilation and should never be
covered or otherwise obstructed. Do not push objects into any of the
openings.
Important safety information
iv WFM2300 and WFM2200A Installation and Safety Instructions

Provide a safe working environment. Always place the product in a
location convenient for viewing the display and indicators.
Be sure your work area meets applicable ergonomic standards. Consult
with an ergonomics professional to avoid stress injuries.
Service safety summary
The Service safety summary section contains additional information
required to safely perform service on the product. Only qualified
personnel should perform service procedures. Read this Service safety
summary and the General safety summary before performing any
service procedures.
To avoid electric shock. Do not touch exposed connections.
Do not service alone. Do not perform internal service or adjustments of
this product unless another person capable of rendering first aid and
resuscitation is present.
Disconnect power. To avoid electric shock, switch off the product power
and disconnect the power cord from the mains power before removing
any covers or panels, or opening the case for servicing.
Use care when servicing with power on. Dangerous voltages or currents
may exist in this product. Disconnect power, remove battery (if
applicable), and disconnect test leads before removing protective
panels, soldering, or replacing components.
Terms in the manual
These terms may appear in this manual:
WARNING. Warning statements identify conditions or practices that
could result in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that
could result in damage to this product or other property.
Important safety information
WFM2300 and WFM2200A Installation and Safety Instructions v

Symbols on the product
When this symbol is marked on the product, be sure to
consult the manual to find out the nature of the potential
hazards and any actions which have to be taken to avoid
them. (This symbol may also be used to refer the user to
ratings in the manual.)
The following symbols may appear on the product:
Important safety information
vi WFM2300 and WFM2200A Installation and Safety Instructions