Tektronix WFM6100 Opt. MB User manual

Instructions
WFM61UP FP, WFM70UP FP, and WFM71UP FP
Front Panel Upgrade
WFM6100, WFM7000, and WFM7100
Waveform Monitors
075-0948-00
*P075094800*
075094800
Warning
The servicing instructions are for use by qualified
personnel only. To avoid personal injury, do not
perform any servicing unless you are qualified to
do so. Refer to all safety summaries prior to
performing service.
www.tektronix.com

Copyright ©Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or
suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes
that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14200 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
HIn North America, call 1-800-833-9200.
HWorldwide, visit www.tektronix.com to find contacts in your area.

WFM61UP FP, WFM70UP FP, and WFM71UP 1
Service Safety Summary
Only qualified personnel should perform service procedures. Read this Service
Safety Summary before performing any service procedures.
Do Not Service Alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
Disconnect Power. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power.
Use Care When Servicing With Power On. Dangerous voltages or currents may
exist in this product. Disconnect power, remove battery (if applicable), and
disconnect test leads before removing protective panels, soldering, or replacing
components.
To avoid electric shock, do not touch exposed connections.

Service Safety Summary
2WFM61UP FP, WFM70UP FP, and WFM71UP

WFM61UP FP, WFM70UP FP, and WFM71UP 3
Kit Description
This document describes replacing the waveform monitor front panel with the
new, upgraded front panel. One very obvious change is the number of buttons on
the front panel; there are many more buttons on the new front panel. This is
necessary because the new front panel does not employ a touch-screen interface;
all control is through the front panel buttons. Among other things, this change
provides a noticeable improvement in instrument front panel response.
Products
WFM6100 All
WFM7000 All
WFM7100 All
Minimum Tool and Equipment List
Required tools and equipment Part number
PC with USB port -- -- -- -- -- -- -- -- -- --
Network connection ---------- ----------
Torque screwdriver handle Standard tool
T-10 TORX bit Standard tool
Kit Parts List
Quantity Part number Description
1Each 614--1044--xx FRONT PANEL ASSY
1 Each 063--4072--xx USB FLASH DRIVE, PROGRAMMED
1Each NS OPTION KEY LABEL
1 Each 075--0948--00 UPGRADE KIT INSTRUCTIONS (THIS DOCUMENT)
1Each NS IMPORTANT DOCUMENTS ENVELOPE
1Each 071-2191-01 MANUAL, TECH; SVCPT--UPG; TEKTRONIX SUPPLE-
MENTAL INFORMATION SHEET FOR THE PEOPLES
REPUBLIC OF CHINA; CHINA ROHS
NS - Not Saleable

Kit Description
4WFM61UP FP, WFM70UP FP, and WFM71UP

WFM61UP FP, WFM70UP FP, and WFM71UP 5
Installation Instructions
These instructions are for personnel who are familiar with servicing the product.
If you need further details for disassembling or reassembling the product, refer to
the appropriate product manual. Contact your nearest Tektronix, Inc., Service
Center or Tektronix Factory Service for installation assistance.
CAUTION. To prevent static discharge damage, service the product only in a
static-free environment. Observe standard handling precautions for static-sensi-
tive devices while installing this kit. Always wear a grounded wrist strap,
grounded foot strap, and static resistant apparel while installing this kit.
These instructions will guide you through the following steps:
HUpdate the software
HConnect the waveform monitor to the network, if not already connected
HObtain the waveform monitor IP address
HVerify the network connection
HObtain the waveform monitor software version
HUpdate the software
HReplace the front panel
HRemove the top cover
HRemove the fan bracket (optional)
HRemove the front panel/LCD assembly
HInstall the new front panel/LCD assembly
HReplace the fan bracket
HReplace the top cover
HApply the instrument model label
HVerify Operation
HCheck waveform monitor IP address; it may have changed
HUpdate the Installed Options

Installation Instructions
6WFM61UP FP, WFM70UP FP, and WFM71UP
Update the Software
Before installing the new front panel assembly, you must first update the
instrument software, located on the USB Flash Drive included in this kit.
These instructions are written for a PC running Windows XP.
NOTE. If a notebook computer is used, make sure it has a full battery charge or
is connected to an AC power source.
If the PC and the waveform monitor are already network connected, go to
Obtain waveform monitor IP address,onpage7.
NOTE. Do not reboot the instrument after updating the software. Disconnect the
power cord and proceed with the front panel replacement.
To allow network access to the instrument, you need to set the IP address.
Network addresses can be assigned either automatically or manually. If your
network does not use DHCP, you will have to manually enter the address for the
instrument. To get an address, talk to your LAN administrator.
1. Verify that the waveform monitor is connected to the network.
2. Power on the waveform monitor.
3. Press the MAIN button to display the Main menu, and then touch the
Config soft key to display the Configuration submenu.
4. Touch the Utilities soft key, and then the Communications soft key.
5. Touch the Config Mode soft key, and then set the Config Mode to Manual
or DHCP, depending on your network setup.
Selecting the configuration mode will close the Config Mode submenu.
6. Touch the Network Setup soft key.
a. Select Enabled under Remote Control Port.
b. Select Enabled under Remote Web Interface.
7. If you can’t use DHCP you will have to set the IP Address, subnet mask, and
gateway address network parameters in the Network setup menu; see your
LAN administrator for the required values. (Be sure to use compatible
addresses between the PC and the monitor.)
8. Press the Close soft keys to close the submenus.
Network Connection and
IP Settings

Installation Instructions
WFM61UP FP, WFM70UP FP, and WFM71UP 7
These steps assume the instrument has already been configured for network
connection as described previously, and guided by a network administrator.
1. Press the MAIN button, then touch the Config softkey.
2. Touch the Utilities, then the Communications, and the Network Setup
softkeys.
3. Make a note of the waveform monitor’s IP address. You will need that in the
next procedure.
NOTE. If you are using DHCP and the waveform monitor did not receive an IP
address, go back through steps 3 through 5 of the Network Connection and IP
Settings procedure, change the waveform monitor to Manual, and then change it
back to DHCP.
If the waveform monitor still does not receive an IP address, cycle the power
while in DHCP mode.
4. Touch OK to close the network setup window.
1. On the PC, select Start >All Programs >Accessories >Command
Prompt.
2. Change to drive C:\ by typing cd c:\ in the command window, and then press
the Enter key.
3. In the command window, type ping, followed by the waveform monitor’s IP
address, and then press the Enter key. For example: ping 192.168.1.2.
4. Check that the replies that appear on the PC resemble the following:
Pinging 192.168.1.2 with 32 bytes of data:
Reply from 192.168.1.2: bytes=32 time=2ms TT =63
Reply from 192.168.1.2: bytes=32 time=1ms TT =63
Reply from 192.168.1.2: bytes=32 time=1ms TT =63
Reply from 192.168.1.2: bytes=32 time=1ms TT =63
Ping statistics for 192.168.1.2:
Packets: Sent = 4, Received = 4, ost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 1ms, Maximum = 2ms, Average = 1ms
If there are no replies, check your network connections and verify that the
waveform monitor settings and PC settings are correct.
Obtain waveform monitor
IP address
Verify the network
connection

Installation Instructions
8WFM61UP FP, WFM70UP FP, and WFM71UP
In this procedure, you load the Upgrade Assistant file into the PC, check the
waveform monitor software version, and run the Upgrade Assistant.
1. Find the plastic bag in the upgrade kit that contains the USB Flash Drive and
the Option Key label, and plug the Flash Drive into a USB port on the PC.
2. Create a folder on your PC. Name the folder something easy to remember,
like “c:\wfmupgrade”.
3. Copy the file WfmUpgrade.exe from the USB Flash Drive into the directory
created in step 2.
CAUTION. DO NOT just unplug the USB Flash Drive from the PC. This can
erase the files and/or damage the USB Flash Drive.
4. Unmount the USB Flash Drive, using one of the following methods:
HYou can use the Safely remove hardware icon, on the taskbar:
Left-click the icon and select the Safely remove USB Mass Storage
Device -- Drive (x) button that appears. Wait until the Safe To Remove
Hardware message appears before removing the USB Flash Drive from
the USB port.
HOr, you can open My Computer, right-click on the drive with the USB
Flash Drive, and select Eject. Wait for the light to go out on the Flash
Drive before removing it from the USB port.
5. On the waveform monitor, press the MAIN button, then touch the Config
--Utilities andthentheView Hw/Sw Version softkeys. Make a note of the
software version (1.1, 1.23, or 1.25).
6. Touch OK to close the HW/SW version display.
NOTE. You will need to identify whether your software is Version 1.1 or if it’s a
later version, in step 12.
7. Plug the same USB Flash Drive, included in the upgrade kit, into the
waveform monitor USB port.
8. On the PC, select Start >All Programs >Accessories >Command
Prompt to open the Command Prompt window.
9. On the PC, change the directory to the directory created in step 2. For
example, type cd c:\wfmupgrade in the Command Prompt window and
press the Enter key to change to the c:\wfmupgrade directory.
Update the software