Tektronix Keithley 2260B Series Owner's manual


2260B Series
www.keithley.com

360W and 720W Multi-Range Programmable DC Power
Supplies



Rev. A / March 2014
Programming Manual
ATektronix Company
A Greater Measure of Confidence
All manuals and user guides at all-guides.com
all-guides.com

Series 2260B
360W and 720W Multi-Range Programmable DC Power
Supplies
PROGRAMMING MANUAL
ISO-9001 CERTIFIED MANUFACTURER
All manuals and user guides at all-guides.com

This manual contains proprietary information, which is protected by
copyright. All rights are reserved. No part of this manual may be
photocopied, reproduced or translated to another language without
prior written consent.
The information in this manual was correct at the time of printing.
However, we continue to improve our products and reserve the rights
to change specification, equipment, and maintenance procedures at
any time without notice.
All manuals and user guides at all-guides.com

Table of Contents
1
Table of Contents
SAFETY INSTRUCTIONS ................................................... 2
GETTING STARTED........................................................... 6
2260B Series Overview ...........................................7
Appearance ............................................................9
Configuration Settings .........................................15
REMOTE CONTROL ........................................................ 20
Interface Configuration ........................................21
Socket Server Examples........................................32
Command Syntax .................................................36
Command List...................................................... 39
Status Register Overview......................................78
Error List..............................................................89
APPENDIX ...................................................................... 98
2260B Default Settings.........................................98
Error Messages & Messages .............................. 100
LED Display Format ........................................... 100
INDEX............................................................................101
All manuals and user guides at all-guides.com

2260B Series Programming Manual
2
SAFETY INSTRUCTIONS
This chapter contains important safety
instructions that you must follow during
operation and storage. Read the following before
any operation to insure your safety and to keep
the instrument in the best possible condition.
Safety Symbols
These safety symbols may appear in this manual or on the
instrument.
WARNING Warning: Identifies conditions or practices that
could result in injury or loss of life.
CAUTION Caution: Identifies conditions or practices that
could result in damage to the instrument or to
other properties.
DANGER High Voltage
Attention Refer to the Manual
Protective Conductor Terminal
Earth (ground) Terminal
All manuals and user guides at all-guides.com

SAFETY INSTRUCTIONS
3
Do not dispose electronic equipment as unsorted
municipal waste. Please use a separate collection
facility or contact the supplier from which this
instrument was purchased.
Safety Guidelines
General Guideline
CAUTION
•Do not place any heavy object on the
instrument.
•Avoid severe impact or rough handling that
leads to damaging the instrument.
•Do not discharge static electricity to the
instrument.
•Use only mating connectors, not bare wires, for
the terminals.
•Do not block the cooling fan opening.
•Do not disassemble the instrument unless you
are qualified.
(Measurement categories) EN 61010-1:2001 specifies the
measurement categories and their requirements as follows. This
instrument falls under category II.
•Measurement category IV is for measurement performed at the
source of low-voltage installation.
•Measurement category III is for measurement performed in the
building installation.
•Measurement category II is for measurement performed on the
circuits directly connected to the low voltage installation.
•Measurement category I is for measurements performed on
circuits not directly connected to Mains.
Power Supply
WARNING
•AC Input voltage range: 85VAC~265VAC
•Frequency: 47Hz~63Hz
•To avoid electrical shock connect the protective
grounding conductor of the AC power cord to
an earth ground.
All manuals and user guides at all-guides.com
all-guides.com

2260B Series Programming Manual
4
Cleaning the
Instrument
•Disconnect the power cord before cleaning.
•Use a soft cloth dampened in a solution of mild
detergent and water. Do not spray any liquid.
•Do not use chemicals containing harsh material
such as benzene, toluene, xylene, and acetone.
Operation
Environment
•Location: Indoor, no direct sunlight, dust free,
almost non-conductive pollution (Note below)
•Relative Humidity: 20%~ 85%
•Altitude: < 2000m
•Temperature: 0°C to 50°C
(Pollution Degree) EN 61010-1:2001 specifies the pollution degrees
and their requirements as follows. The Instrument falls under
degree 2.
Pollution refers to “addition of foreign matter, solid, liquid, or
gaseous (ionized gases), that may produce a reduction of dielectric
strength or surface resistivity”.
•Pollution degree 1: No pollution or only dry, non-conductive
pollution occurs. The pollution has no influence.
•Pollution degree 2: Normally only non-conductive pollution
occurs. Occasionally, however, a temporary conductivity caused
by condensation must be expected.
•Pollution degree 3: Conductive pollution occurs, or dry, non-
conductive pollution occurs which becomes conductive due to
condensation which is expected. In such conditions, equipment
is normally protected against exposure to direct sunlight,
precipitation, and full wind pressure, but neither temperature
nor humidity is controlled.
Storage
environment
•Location: Indoor
•Temperature: -25°C to 70°C
•Relative Humidity: <90%
Disposal
Do not dispose this instrument as unsorted
municipal waste. Please use a separate collection
facility or contact the supplier from which this
instrument was purchased. Please make sure
discarded electrical waste is properly recycled to
reduce environmental impact.
All manuals and user guides at all-guides.com

SAFETY INSTRUCTIONS
5
Power cord for the United Kingdom
When using the instrument in the United Kingdom, make sure the
power cord meets the following safety instructions.
NOTE: This lead/appliance must only be wired by competent persons
WARNING: THIS APPLIANCE MUST BE EARTHED
IMPORTANT: The wires in this lead are coloured in accordance with the
following code:
Green/ Yellow: Earth
Blue: Neutral
Brown: Live (Phase)
As the colours of the wires in main leads may not correspond with
the coloured marking identified in your plug/appliance, proceed
as follows:
The wire which is coloured Green & Yellow must be connected to
the Earth terminal marked with either the letter E, the earth symbol
or coloured Green/Green & Yellow.
The wire which is coloured Blue must be connected to the terminal
which is marked with the letter N or coloured Blue or Black.
The wire which is coloured Brown must be connected to the
terminal marked with the letter L or P or coloured Brown or Red.
If in doubt, consult the instructions provided with the equipment
or contact the supplier.
This cable/appliance should be protected by a suitably rated and
approved HBC mains fuse: refer to the rating information on the
equipment and/or user instructions for details. As a guide, a cable
of 0.75mm2should be protected by a 3A or 5A fuse. Larger
conductors would normally require 13A types, depending on the
connection method used.
Any exposed wiring from a cable, plug or connection that is
engaged in a live socket is extremely hazardous. If a cable or plug is
deemed hazardous, turn off the mains power and remove the cable,
any fuses and fuse assemblies. All hazardous wiring must be
immediately destroyed and replaced in accordance to the above
standard.
All manuals and user guides at all-guides.com

2260B Series Programming Manual
6
GETTING STARTED
This chapter describes the power supply in a
nutshell, including its main features and front /
rear panel introduction. After going through the
overview, please read the theory of operation to
become familiar with the operating modes,
protection modes and other safety considerations.
2260B Series Overview ....................................................... 7
Series lineup................................................................................................................7
Main Features.............................................................................................................8
Appearance ........................................................................ 9
2260B Front Panel.....................................................................................................9
Rear Panel .................................................................................................................12
All manuals and user guides at all-guides.com

GETTING STARTED
7
2260B Series Overview
Series lineup
The 2260B series consists of 4 models, divided into 2 different
model types covering 2 power capacities: 360W models and 720W
models.
Model name Type Voltage rating
Current rating
Power
2260B-30-36 360W models 0~30V 0~36A 360W
2260B-80-13 360W models 0~80V 0~13.5A 360W
2260B-30-72 720W models 0~30V 0~72A 720W
2260B-80-27 720W models 0~80V 0~27A 720W
Apart from the differences in output, each unit differs in size. The
720W models are larger than the 360W models to accommodate the
increase in power.
360W models
720W models
All manuals and user guides at all-guides.com