Tekvox TekTouchPad 78034 User manual

www.tekvox.com
TekTouchPad - Podium
78034
Installation Guide
Included in this Product Package:
Step 1: Select Location for TekTouchPad
The TekTouchPad mounting wedge should be placed on the podium or table so that it is comfortably
accessible, and does not obstruct any displays or monitors. There must be at least 3” to either side
of the wedge to allow for normal usage. The wedge is approximately 4 3/4” long & 2 13/16” wide.
Step 2: Drill Screw & Cable Passthrough Holes
With the TekTouchPad mounting wedge in its intended location, lightly trace
around its perimeter with a pencil. Remove the wedge, and mark the positions of
all five (5) holes shown on the hole template. When mounted, the lower end of
the angled wedge face should be facing towards the user.
Using a 1/16” bit, drill the four (4) holes—one in each corner—for mounting the
wedge to a depth of ½”. Next, use a 5/8” bit to drill the central cable passthrough
hole all the way through the table surface. Clean away all sawdust and/or debris
from the drilling process.
Step 3: Attach Mounting Wedge to Table
Using the four (4) provided wood screws, attach the TekTouchPad mounting wedge
to the table. With the taller end of the wedge facing away from the user, the four
mounting posts on the wedge should align with the 1/16” holes drilled in Step 2.
Tighten screws until snug, but do not overtighten, as this can damage the wedge.
Ensure that the wedge is stable before proceeding.
TekTouchPad Back Mounting
Plate
Mounting Wedge
#6 Wood
Screws (4)
6-32 Machine
Screws (2)
DC Power Supply
DB9/RJ12
Serial Cable
3-pin/DB9
Serial Cable

www.tekvox.com
TekTouchPad - Podium
78034
Installation Guide
Step 4: Fasten Back Mounting Plate to Wedge
Using the two (2) provided machine screws, attach the back mounting plate to the
angled face of the wedge. Ensure that the “TOP” text is facing upwards, and that
the arrows point towards the taller end of the wedge.
Be very careful not to overtighten these screws, as this can warp the plate and prevent
the TekTouchPad from seating properly.
Step 5: Route Cable up through Mounting Wedge
Route clear plastic RJ12 head of black DB9/RJ12 Serial Cable from
underneath table surface through 5/8” hole drilled in Step 2. Run cable out
through rectangular opening in mounting wedge, with at least 6” of slack.
Step 6: Connect & Mount TekTouchPad
Connect clear plastic RJ12 head of black DB9/RJ12 serial cable to port
on back of TekTouchPad. Ensure that the head clicks into place.
Orient the TekTouchPad such that the cable runs directly downward,
and the wider portion of the housing is lower. Gently push the
TekTouchPad towards the mounting wedge, ensuring that the cable
does not get pinched, kinked, or bent too sharply.
Align the four posts of the back mounting plate with the four holes on the back of the TekTouchPad
housing. Once aligned, push the TekTouchPad towards the mounting plate until mounted securely.
Check that the TekTouchPad does not move when pressed.
Step 7: Finalize Cabling
1. Plug green 3-pin connector of 3-pin/DB9 serial cable into RS232
port of 1201-N+
2. Connect DB9 head of gray 3-pin/DB9 serial cable to DB9 head of
black DB9/RJ12 serial cable. Tighten screws until snug to lock heads
together for a secure connection.
3. Connect 2.1mm male plug (with central pin) of black DB9/RJ12
cable to 2.1mm female connector of TekTouchPad power supply.
4. Connect TekTouchPad power supply to available standard
electrical outlet.
Ensure that all cables are neatly routed, and that any excess length is
neatly coiled without obstructing access to any equipment.