Telestream PRISM MPX2-DUALDSP Manual
Copyright © 2020 Telestream, LLC and its Affiliates. All rights reserved. TELESTREAM is a registered trademark of
Telestream, LLC. All other trade names referenced are the service marks, trademarks, or registered trademarks of their
respective companies.
Telestream products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TELESTREAM is a registered trademark of Telestream, LLC.
Contact Telestream
Telestream, LLC
848 Gold Flat Road
Nevada City, CA 95959
USA
For product information, sales, service, and technical support:
Worldwide, visit www.telestream.net/telestream-support/video/support.htm to find contacts in your area.
Warranty
Telestream on behalf of itself and its Affiliates (“Telestream”) warrants that this product will be free from defects in
materials and workmanship for a period of one (1) year from the date of shipment. If any such product proves
defective during this warranty period, Telestream, at its option, either will repair the defective product without charge
for parts and labor, or will provide a replacement in exchange for the defective product. Parts, modules and
replacement products used by Telestream for warranty work may be new or reconditioned to like new performance.
All replaced parts, modules and products become the property of Telestream.
In order to obtain service under this warranty, Customer must notify Telestream of the defect before the expiration
of the warranty period and make suitable arrangements for the performance of service. Customer shall be
responsible for packaging and shipping the defective product to the service center designated by Telestream, with
shipping charges prepaid. Telestream shall pay for the return of the product to Customer if the shipment is to a
location within the country in which the Telestream service center is located. Customer shall be responsible for
paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate
maintenance and care. Telestream shall not be obligated to furnish service under this warranty a) to repair damage
resulting from attempts by personnel other than Telestream representatives to install, repair or service the product;
b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any damage
or malfunction caused by the use of non- Telestream supplies; or d) to service a product that has been modified or
integrated with other products when the effect of such modification or integration increases the time or difficulty of
servicing the product.
THIS WARRANTY IS GIVEN BY TELESTREAM WITH RESPECT TO THE PRODUCT IN LIEU OF ANY OTHER
WARRANTIES, EXPRESS OR IMPLIED. TELESTREAM AND ITS VENDORS DISCLAIM ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TELESTREAM’S
RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE
REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY. TELESTREAM AND ITS
VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES IRRESPECTIVE OF WHETHER TELESTREAM OR THE VENDOR HAS ADVANCE NOTICE OF THE
POSSIBILITY OF SUCH DAMAGES.
[W2 – 15AUG04]
TELESTREAM SOFTWARE LICENSE AGREEMENT
THE PROGRAM, OR PROGRAMS, ENCODED OR INCORPORATED WITHIN EQUIPMENT OR ACCOMPANYING THIS
AGREEMENT, IS FURNISHED SUBJECT TO THE TERMS AND CONDITIONS OF THIS AGREEMENT. RETENTION OF THE
PROGRAM FOR MORE THAN THIRTY DAYS OR USE OF THE PROGRAM IN ANY MANNER WILL BE CONSIDERED
ACCEPTANCE OF THE AGREEMENT TERMS. IF THESE TERMS ARE NOT ACCEPTABLE, THE UNUSED PROGRAM AND ANY
ACCOMPANYING DOCUMENTATION SHOULD BE RETURNED PROMPTLY TO TELESTREAM FOR A FULL REFUND OF THE
LICENSE FEE PAID. (FOR INFORMATION REGARDING THE RETURN OF PROGRAMS ENCODED OR INCORPORATED WITHIN
EQUIPMENT, CONTACT THE NEAREST TELESTREAM SALES OFFICE.)
DEFINITIONS
"Telestream" means Telestream, LLC, a Delaware limited liability company, and its Affiliates , or the local Telestream legal entity
that is supplying the equipment. "Program" means the Telestream software product (executable program and/or data) enclosed with
this Agreement or included within the equipment with which this Agreement is packed. "Customer" means the person or
organization in whose name the Program was ordered.
LICENSE
Customer may:
1. Use the Program on a single machine at any one time; and
2. Copy the Program for archival or backup purposes, provided that no more than one (1) such copy is permitted to exist at any one
time. Each copy of the Program made by Customer must include a reproduction of any copyright notice or restrictive rights
legend appearing in or on the copy of the Program as received from Telestream.
Customer may not:
1. Use the Program on more than one machine at any one time;
2. Transfer the Program to any person or organization outside of Customer or the corporation of which Customer is a part without
the prior written consent of Telestream, except in connection with the transfer of the equipment within which the programs are
encoded or incorporated;
3. Export or re-export, directly or indirectly, the program, any associated documentation, or the direct product thereof, to any country
to which such export or re-export is restricted by law or regulation of the United States or any foreign government having
jurisdiction without the prior authorization, if required, of the Office of Export Administration, Department of Commerce,
Washington, D.C. and the corresponding agency of such foreign government;
4. Modify the Program, create derivative works, or merge the Program with another program;
5. Reverse compile or disassemble the Program for any purpose, beyond the extent that such activity is expressly permitted by
applicable open source licenses or applicable law notwithstanding this limitation; or
6. Copy the documentation accompanying the Program.
For Programs designed to reside on a single-machine and support one or more additional machines, either locally or remotely,
without permitting the Program to be transferred to an additional machine for local execution, the additional machines shall be
considered within the definition of "single machine." For programs permitting the Program to be transferred to an additional machine
for local execution, a separate license shall be required for each such machine with which the Program may be used. Title to the
Program and all copies thereof, but not the media on which the Program or copies may reside, shall be and remain with Telestream
or others for whom Telestream has obtained a respective licensing right. Customer shall pay when due all property taxes that may
now or hereafter be imposed, levied or assessed with respect to the possession or use of the Program or this license and shall file
all reports required in connection with such taxes. If the Program or any related documentation is acquired by or for an agency of the
U.S. Government, the Program and documentation
shall be considered “commercial computer software” or “commercial computer software documentation” respectively, as those terms
are used in 48 CFR §12.212, 48 CFR §227.7202, or 48 CFR §252.227-7014, and are licensed with only those rights as are granted
to all other licensees as set forth in this Agreement.
THE PROGRAM MAY NOT BE USED, COPIED, MODIFIED, MERGED, OR TRANSFERRED TO ANOTHER EXCEPT AS EXPRESSLY
PERMITTED BY THESE TERMS AND CONDITIONS. UPON TRANSFER OF ANY COPY, MODIFICATION, OR MERGED PORTION
OF THE PROGRAM, THE LICENSE GRANTED HEREIN IS AUTOMATICALLY TERMINATED WITH RESPECT TO THE PARTY THAT
TRANSFERS THE PROGRAM.
TERM
The license granted herein is effective upon acceptance by Customer, and shall remain in effect until terminated as provided herein.
The license may be terminated by Customer at any time upon written notice to Telestream. The license may be terminated by
Telestream or any third party from whom Telestream may have obtained a respective licensing right if Customer fails to comply with
any term or condition and such failure is not remedied within thirty (30) days after notice hereof from Telestream or such third party.
Upon termination by either
party, Customer shall return to Telestream or destroy, the Program and all associated documentation, together with all copies in any
form.
LIMITED WARRANTY
The Program is provided "as is" without warranty of any kind, either express or implied. Telestream does not warrant that the
functions contained in the Program will meet Customer's requirements or that the operation of the Program will be uninterrupted or
error-free.
TELESTREAM AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. LIMITATION OF LIABILITY, IN NO EVENT SHALL TELESTREAM OR OTHERS FROM WHOM
TELESTREAM HAS OBTAINED A LICENSING RIGHT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES ARISING OUT OF OR CONNECTED WITH CUSTOMER'S POSSESSION OR USE OF THE
PROGRAM, EVEN IF TELESTREAM OR SUCH OTHERS HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
THIRD-PARTY DISCLAIMER
Except as expressly agreed otherwise, third parties from whom Telestream may have obtained a licensing right do not warrant the
program, do not assume any liability with respect to its use, and do not undertake to furnish any support or information relating
thereto.
GENERAL
This Agreement contains the entire agreement between the parties with respect to the use, reproduction, and transfer of the
Program. Neither this Agreement nor the license granted herein is assignable or transferable by Customer without the prior written
consent of Telestream. This Agreement and the license granted herein shall be governed by the laws of the state of California. nAll
questions regarding this Agreement or the license granted herein should be directed to the nearest Telestream Sales Office.
PRISM MPX2-DUALDSP Installation and Safety Instructions
i
Table of Contents
Important compliance and safety information .................................................................................................... ii
Preface...............................................................................................................................................................x
Product description ....................................................................................................................................x
Documentation.......................................................................................................................................... xi
Conventions used in this manual .............................................................................................................. xi
Installation..........................................................................................................................................................1
Initial product inspection ............................................................................................................................1
Accessories................................................................................................................................................2
Operating requirements .............................................................................................................................3
Rear-panel connectors...............................................................................................................................5
Dual Display installation.............................................................................................................................6
Power-on and power-off procedures........................................................................................................12
Operation .........................................................................................................................................................14
Configure the MPX2-DUALDSP Dual Display .........................................................................................14
PRISM MPX2-DUALDSP Installation and Safety Instructions
ii
Important compliance and safety information
United States of America Compliance Notices
Class A Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15, Subpart B of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a commercial installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Safety
UL 61010-1: 2012 R4.16: Safety Requirements for Electrical Equipment for Measurement,
Control, and Laboratory Use - Part 1: General Requirements.
Environmental
Perchlorate Materials: this product contains one or more type CR lithium batteries. According to
the state of California, CR lithium batteries are classified as perchlorate materials and require
special handling.
See www.dtsc.ca.gov/hazardouswaste/perchlorate for additional information.
Canada Compliance Notices
Department of Communications Radio Interference Regulations
This digital apparatus does not exceed the Class A limits for radio-noise emissions from a digital
apparatus as set out in the Radio Interference Regulations of the Canadian Department of
Communications. This Class A digital apparatus complies with Canadian ICES-003.
Reglement sur le brouillage radioelectrique du Quadstere des Communications
Cet appareil numerique respecte les limites de bruits radioelectriques visant les appareils
numeriques de classe A prescrites dans le Reglement sur le brouillage radioelectrique du
Quadstere des Communications du Canada. Cet appareil numerique de la Classe A est
conforme a la norme NMB-003 du Canada.
PRISM MPX2-DUALDSP Installation and Safety Instructions
iii
Safety
CAN/CSA-22.2 NO. 61010-1-12 + Gil + Gl2:: Safety Requirements for Electrical
Equipment for Measurement, Control, and Laboratory Use - Part 1: General
Requirements.
Sécurité
CAN / CSA-22.2 NO. 61010-1-12 + Gil + Gl2 :: Exigences de sécurité pour l'électricité
Matériel de mesure, de contrôle et d'utilisation en laboratoire - Partie 1: Généralités
Exigences.
European Union and European Free Trade Association (EFTA) Compliance
Notices
This equipment may be operated in the countries that comprise the member countries of the
European Union and the European Free Trade Association. These countries, listed in the
following paragraph, are referred to as The European Community throughout this document:
AUSTRIA, BELGIUM, BULGARIA, CYPRUS, CZECH REPUBLIC, DENMARK, ESTONIA,
FINLAND, FRANCE, GERMANY, GREECE, HUNGARY, IRELAND, ITALY, LATVIA,
LITHUANIA, LUXEMBOURG, MALTA, NETHERLANDS, POLAND, PORTUGAL, ROMANIA,
SLOVAKIA, SLOVENIA, SPAIN, SWEDEN, UNITED KINGDOM, !CELANO, LICHTENSTEIN,
NORWAY, SWITZERLAND
Declaration of Conformity
Marking by the “CE” symbol indicates compliance with the Essential Requirements of the EMC
Directive of the European Union 2014/30/EU
This equipment meets the following conformance standards:
Safety
EN 61010-1: Safety Requirements for Electrical Equipment for Measurement, Control, and
Laboratory Use - Part 1: General Requirements
Low Voltage Directive 2014/35/EU
Emissions
EN 55032: 2012 + AC: 2013, CISPR 32: 2015, EN 61000-3-2: 2014,
EN 61000-3-3: 2013
Immunity
EN 55103-2: 2009, EN 61000-4-2: 2009,
EN 61000-4-3: 2006 + Al: 2008 + A2: 2010, EN 61000-4-4: 2004 + Al: 2010,
EN 61000-4-5: 2006, EN 61000-4-6: 2009, EN 61000-4-11: 2004
Environments: E2
Warnings
Warning! This is a Class A product. In a domestic environment, this product may cause radio
interference, in which case, the user may be required to take appropriate measures.
PRISM MPX2-DUALDSP Installation and Safety Instructions
iv
Achtung! Dieses ist ein Gerat der Funkstorgrenzwertklasse A. In Wohnbereichen konnen bei
Betrieb dieses Gerates Rundfunkstorungen auftreten, in welchen Fallen der Benutzer fur
entsprechende Gegenmal3nahmen verantwortlich ist.
Attention! Ceci est un produit de Classe A. Dans un environnement domestique, ce produit
risque de creer des interferences radioelectriques, ii appartiendra alors a l?utilisateur de prendre
les mesures specifiques appropriees.
Notes:
1. For Compliance with the EMC standards listed here, high quality shielded interface cables
should be used.
2. Emissions which exceed the levels required by this standard may occur when this equipment is
connected to a test object.
Environmental Compliance
This section provides information about the environmental impact of the product.
Product end-of-life handling
Observe the following guidelines when recycling an instrument or component:
Equipment recycling
Production of this equipment required the extraction and use of natural resources. The
equipment may contain substances that could be harmful to the environment or human health if
improperly handled at the product's end of life. To avoid release of such substances into the
environment and to reduce the use of natural resources, we encourage you to recycle this
product in an appropriate system that will ensure that most of the materials are reused or
recycled appropriately.
This symbol on the product or its packaging indicates that this product complies with the
applicable European Union requirements according to Directives 2012/19/EU and 2006/66/EC
on waste electrical and electronic - equipment (WEEE) and batteries.
It also indicates that this product must not be disposed of with your other household waste.
Instead, it is your responsibility to dispose of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and electronic equipment. The
separate collection and recycling of your waste equipment at the time of disposal will help
conserve natural resources and ensure that it is recycled in a manner that protects human health
and the environment. For more information about where you can drop off your waste for
recycling, please contact your local authority, or where you purchased your product.
Battery Recycling
This product may contain a rechargeable battery, which must be recycled or disposed of
properly. Please properly dispose of or recycle the battery according to local government
regulations.
Transporting Batteries or products with Batteries in them
The capacity of the lithium ion secondary battery shipped with this product is under 100 Wh. The
lithium content of the installed primary battery is under 1 g. Each battery meets the applicable
requirements of UN Manual of Tests and Criteria Part Ill Section 38.3. Battery quantity is under
the limit for shipment according to Section II of the relevant Packing Instructions from the IATA
Dangerous Goods Regulations. Consult your air carrier for applicability and determination of any
special lithium battery transportation requirements.
PRISM MPX2-DUALDSP Installation and Safety Instructions
v
Restriction of Hazardous Substances
This product is classified as an industrial monitoring and control instrument, and is not required
to comply with the substance restrictions of the RoHS 3 Directives 2011 /65/EU and EU
2015/863 until July 22, 2021. This product does, however, comply with the RoHS 2 Directive
2011/65/EU.
Korea Compliance Statement
사용자안내문
이기기는 업무용 환경에서 사용할 목적으로 적합성평가를 받은 기기로서 가정용
환경에서 사용하는 경우 전파간섭의 우려가 있습니다.
Taiwan Compliance Statement
Japan Compliance Statement
Important Compliance and Safety Information
This manual contains information and warnings that must be followed by the user for safe operation and to
keep the product in a safe condition.
PRISM MPX2-DUALDSP Installation and Safety Instructions
vi
To safely perform service on this product, see the Service safety summary that follows the General
safety summary.
General Safety Summary
Use the product only as specified. Review the following safety precautions to avoid injury and prevent
damage to this product or any products connected to it. Carefully read all instructions. Retain these
instructions for future reference.
Comply with local and national safety codes.
For correct and safe operation of the product, it is essential that you follow generally accepted safety
procedures in addition to the safety precautions specified in this manual.
The product is designed to be used by trained personnel only.
Only qualified personnel who are aware of the hazards involved should remove the cover for repair,
maintenance, or adjustment.
Before use, always check the product with a known source to be sure it is operating correctly.
While using this product, you may need to access other parts of a larger system. Read the safety
sections of the other component manuals for warnings and cautions related to operating the system.
When incorporating this equipment into a system, the safety of that system is the responsibility of the
assembler of the system.
To Avoid Fire or Personal Injury
Use proper power cord: Use only the power cord specified for this product and certified for the
country of use. Do not use the provided power cord for other products.
Ground the product: This product is grounded through the grounding conductor of the power cord. To
avoid electric shock, the grounding conductor must be connected to earth ground. Before making
connections to the input or output terminals of the product, ensure that the product is properly
grounded. Do not disable the power cord grounding connection.
Power disconnect: The power cord disconnects the product from the power source. See instructions
for the location. Do not position the equipment so that it is difficult to operate the power cord; it must
remain accessible to the user at all times to allow for quick disconnection if needed.
Observe all terminal ratings: To avoid fire or shock hazard, observe all rating and markings on the
product. Consult the product manual for further ratings information before making connections to the
product. Do not apply a potential to any terminal, including the common terminal, that exceeds the
maximum rating of that terminal.
Do not operate without covers: Do not operate this product with covers or panels removed, or with
the case open. Hazardous voltage exposure is possible.
Avoid exposed circuitry: Do not touch exposed connections and components when power is present.
Do not operate with suspected failures: If you suspect that there is damage to this product, have it
inspected by qualified service personnel.
PRISM MPX2-DUALDSP Installation and Safety Instructions
vii
Disable the product if it is damaged. Do not use the product if it is damaged or operates incorrectly. If
in doubt about safety of the product, turn it off and disconnect the power cord. Clearly mark the
product to prevent its further operation.
Before use, inspect voltage probes, test leads, and accessories for mechanical damage and replace
when damaged. Do not use probes or test leads if they are damaged, if there is exposed metal, or if a
wear indicator shows.
Examine the exterior of the product before you use it. Look for cracks or missing pieces.
Use only specified replacement parts.
Do not operate in wet/damp conditions: Be aware that condensation may occur if a unit is moved
from a cold to a warm environment.
Do not operate in an explosive atmosphere.
Keep product surfaces clean and dry: Remove the input signals before you clean the product.
Provide proper ventilation: Refer to the manual's installation instructions for details on installing the
product so it has proper ventilation.
Slots and openings are provided for ventilation and should never be covered or otherwise obstructed.
Do not push objects into any of the openings.
Provide a safe working environment: Always place the product in a location convenient for viewing
the display and indicators.
Be sure your work area meets applicable ergonomic standards. Consult with an ergonomics
professional to avoid stress injuries.
Use only the Telestream rackmount hardware specified for this product.
Service Safety Summary
The Service safety summary section contains additional information required to safely perform
service on the product. Only qualified personnel should perform service procedures. Read this
Service safety summary and the General safety summary before performing any service procedures.
To avoid electric shock: Do not touch exposed connections.
Do not service alone: Do not perform internal service or adjustments of this product unless another
person capable of rendering first aid and resuscitation is present.
Disconnect power: To avoid electric shock, switch off the product power and disconnect the power
cord from the mains power before removing any covers or panels, or opening the case for servicing.
Use care when servicing with power on: Dangerous voltages or currents may exist in this product.
Disconnect power, remove battery (if applicable), and disconnect test leads before removing
protective panels, soldering, or replacing components.
Verify safety after repair: Always recheck ground continuity and mains dielectric strength after
performing a repair.
PRISM MPX2-DUALDSP Installation and Safety Instructions
viii
Terms in the Manual
These terms may appear in this manual:
WARNING. Warning statements identify conditions or practices that could result in injury or loss of
life.
CAUTION. Caution statements identify conditions or practices that could result in damage to this
product or other property.
Terms on the Product
These terms may appear on the product:
DANGER indicates an injury hazard immediately accessible as you read the marking.
WARNING indicates an injury hazard not immediately accessible as you read the marking.
CAUTION indicates a hazard to property including the product.
Symbols on the Product
When this symbol is marked on the product, be sure to consult the manual to find out the nature of
the potential hazards and any actions which have to be taken to avoid them. (This symbol may also
be used to refer the user to ratings in the manual.)
The following symbol(s) may appear on the product:
General Safety Product Specific Statements
Use the product only as specified. Review the following safety precautions to avoid injury and prevent
damage to this product or any products connected to it. Carefully read all instructions. Retain these
instructions for future reference.
Comply with local and national safety codes.
For correct and safe operation of the product, it is essential that you follow generally accepted safety
procedures in addition to the safety precautions specified in this manual. The product is designed to
be used by trained personnel only.
Only qualified personnel who are aware of the hazards involved should remove the cover for repair,
maintenance, or adjustment.
Before use, always check the product with a known source to be sure it is operating correctly.
This product is not intended for detection of hazardous voltages.
Use personal protective equipment to prevent shock and arc blast injury where hazardous live
conductors are exposed.
When incorporating this equipment into a system, the safety of that system is the responsibility of the
assembler of the system.
PRISM MPX2-DUALDSP Installation and Safety Instructions
ix
WARNING. To reduce the risk of fire and shock, ensure that the mains supply voltage fluctuations do not
exceed 10% of the operating voltage range.
WARNING. In the module, only the line conductor is fused for over-current protection. The fuse is internal and
not user replaceable. Do not attempt to replace the fuse. If you suspect the fuse has blown, return the unit to an
authorized service center for repair.
WARNING. To prevent injury or death, power off the module and disconnect it from line voltage before
cleaning.
CAUTION. Damage to the module can occur if this module is powered on at temperatures outside the specified
temperature range.
CAUTION. To prevent risk of fire, adequate airflow to instrument(s) and rack adapter must be maintained.
Failure to provide adequate airflow to instrument(s) could cause an instrument to shut down.
PRISM MPX2-DUALDSP Installation and Safety Instructions
x
Preface
This manual describes how to install the PRISM MPX2-DUALDSP Dual Display module and provides basic safety
and operating information. Detailed operating information is available in the user manual. A complete list of PRISM
documentation is provided in this manual. (See Documentation.)
Product description
The PRISM MPX2-DUALDSP provides a 3RU dual touch display unit for the PRISM family of waveform monitors to create
fully integrated audio, video, and data monitoring suite. The PRISM Dual Display module is 19 inches wide with a shallow
installation depth and comes with two sets of USB/Headphone connectors that can be mounted on each rack ear.
Figure i: PRISM MPX2-DUALDSP (rack ear USB/headphone connections not shown)
PRISM MPX2-DUALDSP Installation and Safety Instructions
xi
Documentation
Table i: Product documentation
Telestream
Availability
Document
Manual type
part number
Description
Print
Web
PRISM MPX2
User
071-3738-xx
Describes how to install the
√
√
Installation and
instrument and provides basic safety
Safety Instructions
and operating information
PRISM MPI2
User
D00010021x
Provides detailed operating
√
and MPX2 User
information for the PRISM waveform
Manual
monitor
PRISM MPX2
Field Install
071-3706-xx
Describes how to install the
√
√
Rackmount
Instructions
MPX2 instrument in a 19” equipment
Slides and
rack
Rails Installation
Instructions
Conventions used in this manual
These icons may be used throughout this manual.
Sequence Step Front panel
power
Connect power Network SVGA USB
PRISM MPX2-DUALDSP Installation and Safety Instructions
1
Installation
Initial product inspection
Perform the product inspection procedure when you receive your Dual Display module:
1.
Inspect the shipping carton for external damage, which may indicate damage to the module.
2.
Remove the PRISM Dual Display module from the shipping carton, and then check that the module has not been
damaged in transit. Prior to shipment the module is thoroughly inspected for mechanical defects. The exterior should
not have any scratches or impact marks.
NOTE. Save the shipping carton and packaging materials for module repackaging in case shipment becomes necessary.
3.
Verify that the shipping carton contains the module, the standard accessories, and any optional accessories that you
ordered. (See Accessories.)
Exterior cleaning
The module exterior was inspected for debris when it was shipped. If necessary, you can clean the exterior of the
module.
WARNING. To prevent injury or death, power off the module and disconnect it from line voltage before cleaning.
Clean the exterior surfaces of the chassis with a dry lint-free cloth or a soft-bristle brush. If any dirt remains, use a cloth or
swab dipped in a 75% isopropyl alcohol solution. Use a swab to clean narrow spaces around controls and connectors. Do
not use abrasive compounds on any part of the module that may be damaged by it.
CAUTION. Avoid the use of chemical cleaning agents that might damage the plastics used in the module. Use a 75%
isopropyl alcohol solution as a cleaner and rinse with deionized water. Before using any other type of cleaner, consult
your Telestream Service Center or representative.
2
PRISM MPX2-DUALDSP Installation and Safety Instructions
Accessories
International power cords. Your module was shipped with one of the power cord options. Power cords for use in
North America are UL listed and CSA certified. Cords for use in areas other than North America are approved by at least
one authority acceptable in the country to which the product is shipped.
Opt. A0 – North America power cord
Opt. A1 – Universal EUR power cord
Opt. A2 – United Kingdom power cord
Opt. A3 – Australia power cord
Opt. A4 – 240 V, North America power cord
Opt. A5 – Switzerland power cord
Opt. A6 – Japan power cord
Opt. A10 – China power cord
Opt. A11 – India power cord
Opt. A12 – Brazil power cord
Opt. A99 1 – No power cord
1 When ordering the A99 option, it is the responsibility of the end user to ensure that a certified power cord, for the country or
region it is installed, is used with this module.
CAUTION. To reduce risk of fire and shock, use the certified power cord provided with the product.
Table of contents
Other Telestream Monitor manuals
