Teltonika FMC650 Installation guide

FMC650
Professional tracker with CAN data
reading feature
Quick Manual v1.1

Quick Manual v1.1 // FMC650 2
Telematics
CONTENT
Know your device................................................................................................................................................................................................3
Pinout ...................................................................................................................................................................................................................4
Wiring scheme.....................................................................................................................................................................................................5
Set up your device ..............................................................................................................................................................................................6
PC Connection (Windows)..................................................................................................................................................................................7
How to install USB drivers (Windows) ..............................................................................................................................................................7
Conguration (Windows) ...................................................................................................................................................................................8
Quick SMS conguration................................................................................................................................................................................. 10
Mounting recommendations.......................................................................................................................................................................... 12
Basic characteristics ........................................................................................................................................................................................ 13
LED indications................................................................................................................................................................................................. 13
Electrical characteristics.................................................................................................................................................................................. 16
Safety information .......................................................................................................................................................................................... 18
Certication and Approvals ............................................................................................................................................................................ 19
Warranty ........................................................................................................................................................................................................... 20
Warranty disclaimer ....................................................................................................................................................................................... 20

Quick Manual v1.1 // FMC650 3
Telematics
KNOW YOUR DEVICE
GNSSS ANTENNA
SOCKET
STATUS
LED
J1708 CELLULAR ANTENNA
SOCKET
NAVIGATE
LED
DUAL-SIM
SLOT
BATTERY
SOCKET
MICRO-USBRS232
RS232/RS485
MICRO SD
SLOT
2x10
SOCKET
TOP VIEW TOP VIEW (WITHOUT COVER)BOTTOM VIEW (WITHOUT COVER)

Quick Manual v1.1 // FMC650 4
Telematics
PIN NUMBER PIN NAME DESCRIPTION
1 GND (-) Ground
2CAN 1L SAE J1939 CAN interface Low
channel 1
31WIRE
POWER
Power supply pin for Dallas
1-Wire® devices
4 DIN4 Digital input, channel 1
5 DIN2 Digital input, channel 2
6CAN 2L SAE J1939 CAN interface Low
channel 2
7AIN2 Analog input, channel 2. Input
range: 0-30V/0-10V DC
8 DOUT3 Digital output. Open collector
output
9 DOUT2 Digital output. Open collector
output
10 AIN3 Analog input, channel 3. Input
range: 0-30V/0-10V DC
11 VCC (+) Power supply (+8-32 V DC)
12 CAN 1H SAE J1939 CAN interface High
channel 1
13 1WIRE DATA Data channel for Dallas 1-Wire®
devices
14 DIN3 Digital input, channel 3
15 IGN (DIN1)
Digital input, channel 1.
DEDICATED FOR IGNITION
INPUT
PINOUT
18
17
16
15
19
20
8
7
6
5
9
10
AIN1
DOUT4/AIN4
DOUT1
DIN1
CAN2H
K-LINE
AIN2
DOUT3
DOUT2
CAN2L
DIN2
AIN3
14
13
12
11
4
3
2
1
1WIRE DATA
DIN3
+8...32 V DC
CAN1H
1WIRE POWER
DIN4
CAN1L
GND
FMC650 2x10 socket pinout
16 CAN 2H SAE J1939 CAN interface High
channel 2
17 AIN1 Analog input, channel 1. Input
range: 0-30V/0-10V DC
18 DOUT4/
AIN4
Digital output. Open collector
output OR Analog input, channel
4. Input range: 0-30V/0-10V DC
19 DOUT1 Digital output. Open collector
output
20 K-Line
K-LINE interface for online
Tachograph Vehicle Data
transfer

Quick Manual v1.1 // FMC650 5
Telematics
WIRING SCHEME
BUZZER LED LIGHTS
RELAY
FUEL GAUGE
IBUTTON
POWER SUPPLY
8 - 32V DC
ANALOG
LLS SENSOR ALA RM BUTTON
MULTIPLE
TEMP ERATUR E
SENSORS
30
8586
87a
87
IGNITION
DETECTION
STARTER
TACHOGRAPH
J1939 RFID
CONFIGURATION
VIA PC
RS232
MULTIPLE
LLS SENSORS
BUFFERED
TRANSPARENT
MODE
RS485
RJ9 FUEL DATA
J1708 PROTOCOL
SUPPORT
CONTINENTAL
TPMS
CAN ADAPTERS
USB
20
19
18
17
16
15
14
13
12
11
10
9
8
6
7
5
4
2
1
3
DIN3
1WIRE DATA
+8...32 V DC
DO UT4/AI N4
CAN2H
CAN1H
DIN1
AIN1
DOUT1
K-LINE
AIN3
1WIRE POWER
DIN4
GND
DOUT2
CAN2L
DOUT3
DIN2
CAN1L
AIN2
GARMIN
BUFFERED
TRANSPARENT
MODE
RFID
LLS SENSOR
CARRIER
FREEZER
IRIDIUM EDGE

Quick Manual v1.1 // FMC650 6
Telematics
SET UP YOUR DEVICE
HOW TO INSERT MICRO-SIM CARD AND CONNECT THE BATTERY
1
4
UNSCREW SCREWS
BATTERY CONNECTION
3
6
SIM CARD INSERT
DEVICE IS READY
2
5
COVER REMOVAL
ATTACHING COVER BACK
Unscrew 4 screws counterclockwise that
are located on the bottom of the device.
Connect battery as shown to device.
Remove the cover
After conguration, see “PC Connection
(Windows)”, attach device cover back.
Insert SIM card as shown with PIN
request disabled or read Security
info1how to enter it later in Teltonika
Congurator2. Make sure that SIM card
cut-o corner is pointing forward to slot.
SIM slot 1 is closer to PCB, SIM slot 2 is
the upper one.
1 wiki.teltonika.lt/view/FMC650_Security_info
2 wiki.teltonika.lt/view/Teltonika_Congurator
Screw in all screws. Device is ready to be
mounted.

Quick Manual v1.1 // FMC650 7
Telematics
PC CONNECTION (WINDOWS)
HOW TO INSTALL USB DRIVERS (WINDOWS)
1. Please download COM port drivers from here1.
2. Extract and run TeltonikaCOMDriver.exe.
3. Click Next in driver installation window.
4. In the following window click Install button.
5. Setup will continue installing the driver and eventually the conrmation window will appear. Click Finish to complete the
setup.
1 teltonika-gps.com/downloads/en/FMC650/TeltonikaCOMDriver.zip
1. Power-up FMC650 with DC voltage (8 – 32 V) power supply using supplied power cable. LED’s should start blinking, see “LED
indications1”.
2. Connect device to computer using Micro-USB cable or Bluetooth connection:
• Using Mini-USB cable
• You will need to install USB drivers, see “How to install USB drivers (Windows)2”
3. You are now ready to use the device on your computer.
1 wiki.teltonika-gps.com/view/FMC650_LED_status
2 Page 7, "How to install USB drivers"

Quick Manual v1.1 // FMC650 8
Telematics
MS .NET REQUIREMENTS
Operating system MS .NET Framework version Version Links
Windows Vista
Windows 7
Windows 8.1
Windows 10
MS .NET Framework 4.6.2 32 and 64 bit www.microsoft.com1
1 dotnet.microsoft.com/en-us/download/dotnet-framework/net462
At rst FMC650 device will have default factory settings set. These settings should be changed according to the users needs. Main
conguration can be performed via Teltonika Congurator1software. Get the latest Congurator version from here2. Congurator
operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.
1 wiki.teltonika-gps.com/view/Teltonika_Congurator
2 wiki.teltonika-gps.com/view/Teltonika_Congurator_versions
CONFIGURATION (WINDOWS)

Quick Manual v1.1 // FMC650 9
Telematics
Downloaded Congurator will be in compressed archive.
Extract it and launch Congurator.exe. After launch software
language can be changed by clicking 🌐in the right bottom
corner.
Conguration process begins by pressing on connected device.
FMC650
Various Status window1 tabs display information about GNSS2,
GSM3, I/O4, Maintenance5 and etc. FMC650 has one user
editable prole, which can be loaded and saved to the device.
After any modication of conguration the changes need to
be saved to device using Save to device button. Main buttons
oer following functionality:
 Load from device – loads conguration from device.
 Save to device – saves conguration to device.
 Load from le – loads conguration from le.
 Save to le – saves conguration to le.
 Update rmware – updates rmware on device.
 Read records – reads records from the device.
 Reboot device – restarts device.
 Reset conguration – sets device conguration to
default.
Most important congurator section is GPRS – where all
your server and GPRS settings6 can be congured and Data
Acquisition7– where data acquiring parameters can be
congured. More details about FMC650 conguration using
Congurator can be found in our Wiki8.
After connection to Congurator Status window will be
displayed.
FMC650
1 wiki.teltonika-gps.com/view/FMC650_Status_info
2 wiki.teltonika-gps.com/view/FMC650_Status_info#GNSS_Info
3 wiki.teltonika-gps.com/view/FMC6501_Status_info#GSM_Info
4 wiki.teltonika-gps.com/view/FMC650_Status_info#I.2FO_Info
5 wiki.teltonika-gps.com/view/FMC650_Status_info#Maintenance
6 wiki.teltonika-gps.com/index.php?title=FMC650_GPRS_settings
7 wiki.teltonika-gps.com/index.php?title=FMC650_Data_acquisition_
settings
8 wiki.teltonika-gps.com/index.php?title=FMC650_Conguration

Quick Manual v1.1 // FMC650 10
Telematics
QUICK SMS CONFIGURATION
Default conguration has optimal parameters present to ensure best performance of track quality and data usage.
Quickly set up your device by sending this SMS command to it:
Note: Before SMS text, two space symbols should be inserted.
GPRS SETTINGS:
 2001 – APN
 2002 – APN username (if there are no APN username,
empty eld should be left)
 2003 – APN password (if there are no APN password,
empty eld should be left)
SERVER SETTINGS:
 2004 – Domain
 2005 – Port
 2006 – Data sending protocol (0 – TCP, 1 – UDP)
« setparam 2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0»
1 2 3 4 5 6
1
2
3
4
5
6

Quick Manual v1.1 // FMC650 11
Telematics
DEFAULT CONFIGURATION SETTINGS
MOVEMENT AND IGNITION DETECTION: DEVICE MAKES A RECORD ON MOVING
IF ONE OF THESE EVENTS HAPPEN:
SPEED DIFFERENCE
between last coordinate
and current position is
greater than 10 km/h
VEHICLE DRIVES
100 meters
VEHICLE TURNS
10 degrees
PASSES
300 seconds
After successful SMS conguration, FMC650 device will synchronize time and update records to congured server. Time intervals
and default I/O elements can be changed by using Teltonika Congurator1or SMS parameters2.
1 wiki.teltonika-gps.com/view/Teltonika_Congurator
2 wiki.teltonika-gps.com/view/Template:FMC_Device_Family_Parameter_list
VEHICLE MOVEMENT
will be detected by
accelerometer
DEVICE MAKES A
RECORD ON STOP IF:
1 HOUR PASSES
while vehicle is
stationary and
ignition is o
IGNITION
will be detected by
vehicle power voltage
between 13,2 – 30 V
RECORDS SENDING TO
SERVER:
EVERY 120 SECOND
it is sent to the server
If device has made a
record

Quick Manual v1.1 // FMC650 12
Telematics
MOUNTING RECOMMENDATIONS
CONNECTING WIRES
• Wires should be fastened to the other wires or non-moving parts. Try to avoid heat emitting and moving objects near the
wires.
• The connections should not be seen very clearly. If factory isolation was removed while connecting wires, it should be applied
again.
• If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional
isolation should be applied.
• Wires cannot be connected to the board computers or control units.
CONNECTING POWER SOURCE
• Be sure that after the car computer falls asleep, power is still available on chosen wire. Depending on car, this may happen in
5 to 30 minutes period.
• When module is connected, measure voltage again to make sure it did not decrease.
• It is recommended to connect to the main power cable in the fuse box.
• Use 3A, 125V external fuse.
CONNECTING IGNITION WIRE
• Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
• Check if this is not an ACC wire (when key is in the rst position, most of the vehicle electronics are available).
• Check if power is still available when you turn o any of vehicles devices.
• Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on,
may be chosen.
CONNECTING GROUND WIRE
• Ground wire is connected to the vehicle frame or metal parts that are xed to the frame.
• If the wire is xed with the bolt, the loop must be connected to the end of the wire.
• For better contact scrub paint from the spot where loop is going to be connected.

Quick Manual v1.1 // FMC650 13
Telematics
BEHAVIOUR MEANING
Permanently
switched on GNSS signal is not received
Blinking every
second Normal mode, GNSS is working
O
GNSS is turned o because:
Device is not working or Device is in
sleep mode
Blinking fast
constantly Device rmware is being ashed
BEHAVIOUR MEANING
Blinking every
second Normal mode
Blinking every two
seconds Sleep mode
Blinking fast for a
short time Modem activity
O Device is not working or Device is in
boot mode
LED INDICATIONS
NAVIGATION LED INDICATIONS
STATUS LED INDICATIONS
BASIC CHARACTERISTICS
MODULE
Name MeiG SLM320 -PE2C, MeiG SLM320-
L16A
Technology LTE(CaT1)/ 2G(GSM/GPRS)
GNSS
Module Name Airoha AG3335MB
GNSS GPS, GLONASS, GALILEO, BEIDOU,
QZSS
Receiver L1 and L5 dual-band GNSS receiver
Tracking sensitivity -165 dBM
Position Accuracy < 2.5 CEP
Hot start < 1.5 s
Warm start < 25 s
Cold start < 32 s
CELLULAR
Technology LTE Cat 1, GSM
2G bands SLM320-PE2C: B2/B3/B5/B8
SLM320-L16A: B2/B3/B5/B8
4G bands
SLM320-PE2C:
LTE-FDD:B1/B3/B7/B8/B20/B28
LTE-TDD:B38/B40/B41
SLM320-L16A:
LTE-FDD:B1/B2/B3/B4/B5/B7/B8/
B20/B28
LTE-TDD:B40

Quick Manual v1.1 // FMC650 14
Telematics
Data transfer
LTE FDD: Max 10Mbps (DL)/Max
5Mbps (UL) LTE TDD Max 8Mbps
(DL)/Max 2Mbps (UL) GPRS:
Max 85.6Kbps (DL)/Max 85.6Kbps
(UL)
Data support SMS (text/data)
Transmit power
Class 4 for GSM850/900: 33±2dBm
Class 1 for GSM1800/1900:
30±2dBm
Class 3 for LTE-TDD: 23±3dBm
Class 3 for LTE-FDD: 23±3dBm
Bluetooth LE: up to 8dBm
POWER
Input voltage range
8 - 32 V DC with overvoltage
(compatible with pulse 5a and pulse
5b) and reverse polarity protection
Back-up battery 550 mAh 8,4V Ni-MH battery
Internal fuse 3 A, 125 V
2 W max.
Current
consumption at 12 V
GPRS: average 60 mA
Nominal: average 45 mA (with no
load)
GNSS sleep: average 32 mA
Deep Sleep: average 4 mA
Online Deep Sleep: average 11 mA
Full Load/Peak: <0.25A Max
2 W max.
Current
consumption at 24 V
GPRS: average 35 mA
Nominal: average 24 mA (with no
load)
GNSS sleep: average 17 mA
Deep Sleep: average 2,9 mA
Online Deep Sleep: average 7 mA
Full Load/Peak: <0.25A Max
INTERFACE
Digital Inputs 4
Digital Outputs 4
Analog Inputs 4
1-Wire temperature
sensors 6
1-Wire iButton 1
RS232 2
RS485 1
CAN J1939 2
J1708 1
K-Line 1
LVCAN/ALLCAN 1
GNSS antenna External High Gain
GSM antenna External High Gain
USB 2.0 Mini-USB
LED indication 2 status LED lights
SIM Micro-SIM
SIM 2x SIM Card (Dual-SIM)
Memory 16MB internal ash memory and
external SD card up to 32 GB.
Switchable CAN
terminators Supported on CAN1 and CAN2 lines

Quick Manual v1.1 // FMC650 15
Telematics
FEATURES
Sensors Accelerometer
Scenarios
Green Driving1, Over Speeding
detection2, Jamming detection3,
GNSS Fuel Counter4, Excessive
Idling detection5, Immobilizer6,
iButton Read Notication7, Unplug
detection8, Towing detection9,
Crash detection10, Auto Geofence11,
Manual Geofence12, Trip13
1 wiki.teltonika.lt/index.php?title=FMC650_Features_settings&Green_
Driving
2 wiki.teltonika-gps.com/view/FMC650_Features_settings#Over_Speeding
3 wiki.teltonika-gps.com/view/FMC650_Features_settings#Jamming
4 wiki.teltonika-gps.com/view/FMC650_Features_settings#GPS_Fuel_
Counter
5 wiki.teltonika-gps.com/view/FMC650_Accelerometer_Features_
settings#Excessive_Idling
6 wiki.teltonika-gps.com/view/FMC650_Features_settings#Immobilizer
7 wiki.teltonika-gps.com/view/FMC150_Features_settings#iButton_Read_
Notication
8 wiki.teltonika-gps.com/view/FMC650_Accelerometer_Features_
settings#Unplug_Detection
9 wiki.teltonika-gps.com/view/FMC650_Accelerometer_Features_
settings#Towing_Detection
10 wiki.teltonika-gps.com/view/FMC650_Accelerometer_Features_
settings#Crash_Detection
11 wiki.teltonika-gps.com/view/FMC650_Auto_Geofence_settings
12 wiki.teltonika-gps.com/view/FMC650_Manual_Geofence_settings
13 wiki.teltonika-gps.com/view/FMC650_Trip/Odometer_settings
Sleep modes GPS Sleep,Online Deep Sleep,
Deep Sleep14
Conguration and
rmware update
FOTA Web15, FOTA16, Teltonika
Congurator17 (USB, Bluetooth),
FMBT mobile application18
(Conguration)
SMS Conguration, Events, DOUT
control, Debug
GPRS commands Conguration, DOUT control, Debug
Time
Synchronization GPS, NITZ, NTP
Ignition detection Digital Input 1, Accelerometer,
External Power Voltage, Engine
PHYSICAL SPECIFICATION
Dimensions 104,1 x 76,8 x 31,5 mm (L x W x H)
Weight 197 g
OPERATING ENVIRONMENT
Operating
temperature
(without battery)
-40 °C to +85 °C
14 wiki.teltonika-gps.com/view/FMC650_Sleep_modes
15 wiki.teltonika.lt/view/FOTA_WEB
16 wiki.teltonika.lt/view/FOTA
17 wiki.teltonika.lt/view/Teltonika_Congurator
18 teltonika.lt/product/fmbt-mobile-application/

Quick Manual v1.1 // FMC650 16
Telematics
Storage temperature
(without battery) -40 °C to +85 °C
Battery Charging
temperature Ta = 20 ± 5 °C (Ambient Temp.)
Battery Discharge
temperature Ta = 20 ± 5 °C (Ambient Temp.)
Battery storage
temperature -20 °C to +45° C
Operating humidity 5% to 95% non-condensing
Ingress Protection
Rating IP41
ELECTRICAL
CHARACTERISTICS
CHARACTERISTIC
DESCRIPTION VALUE
SUPPLY VOLTAGE MIN. TYP. MAX. UNIT
Supply Voltage
(Recommended
Operating Conditions)
+8 +32 V
DIGITAL OUTPUT (OPEN DRAIN GRADE)
Drain current (Digital
Output OFF) 120 µA
Drain current
(Digital Output ON,
Recommended
Operating Conditions)
0.5 A
Static Drain-Source
resistance (Digital
Output ON)
400 300 mΩ
DIGITAL INPUT
Input resistance (DIN1) 15 kΩ
Input resistance (DIN2) 15 kΩ
Input resistance (DIN3) 15 kΩ

Quick Manual v1.1 // FMC650 17
Telematics
CHARACTERISTIC
DESCRIPTION VALUE
SUPPLY VOLTAGE MIN. TYP. MAX. UNIT
Input resistance (DIN4) 15 kΩ
Input voltage
(Recommended
Operating Conditions)
0Supply
voltage V
Input Voltage threshold
(DIN1, DIN2, DIN3,
DIN4)
7.5 V
ANALOG INPUT
Input Voltage
(Recommended
Operating Conditions),
Range 1
0 +10 V
Input resistance 120 kΩ
Input Voltage
(Recommended
Operating Conditions),
Range 2
0 +30 V
Input resistance 147 kΩ
1-WIRE
Supply voltage +3.3 +3.9 V
Output inner resistance 7 Ω
Output current (UOUT>
3.0 V) 30 mA
CHARACTERISTIC
DESCRIPTION VALUE
SUPPLY VOLTAGE MIN. TYP. MAX. UNIT
Short circuit current
(UOUT> 0 V) 75 mA
CAN INTERFACE
Internal terminal
resistors CAN bus 120 Ω
Dierential input
resistance 19 30 52 kΩ
Recessive output
voltage 2 2.5 3 V
Dierential output
voltage 0.5 0.7 0.9 V
Common mode input
voltage -30 30 V

Quick Manual v1.1 // FMC650 18
Telematics
This message contains information on how to operate FMC650
safely. By following these requirements and recommendations,
you will avoid dangerous situations. You must read these
instructions carefully and follow them strictly before operating
the device!
• The device uses SELV limited power source. The nominal
voltage is +12 V DC. The allowed voltage range is +8...+32
V DC.
• To avoid mechanical damage, it is advised to transport
the device in an impact-proof package. Before usage,
the device should be placed so that its LED indicators are
visible. They show the status of device operation.
• When connecting the 2x6 connector wires to the vehicle,
the appropriate jumpers of the vehicle power supply
should be disconnected.
• Before unmounting the device from the vehicle, the 2x6
connector must be disconnected. The device is designed
to be mounted in a zone of limited access, which is
inaccessible to the operator. All related devices must meet
the requirements of EN 62368-1 standard. The device
FMC650 is not designed as a navigational device for boats.
SAFETY INFORMATION Do not disassemble the device. If the device is
damaged, the power supply cables are not isolated
or the isolation is damaged, DO NOT touch the
device before unplugging the power supply.
All wireless data transferring devices produce
interference that may aect other devices which are
placed nearby.
The programming must be performed using a PC
with autonomic power supply.
The device must be rmly fastened in a predened
location.
The device must be connected only by qualied
personnel.
Installation and/or handling during a lightning storm
is prohibited.
The device is susceptible to water and humidity.
CAUTION: Risk of explosion if battery is replaced
by an incorrect type. Dispose of used batteries
according to the instructions.
Battery should not be disposed of with general
household waste. Bring damaged or worn-out
batteries to your local recycling center or dispose
them to battery recycle bin found in stores.

Quick Manual v1.1 // FMC650 19
Telematics
CERTIFICATION AND APPROVALS
This sign on the package means that it is necessary
to read the User‘s Manual before your start using the
device. Full User‘s Manual version can be found in
our Wiki1.
1 wiki.teltonika-gps.com/index.php?title=FMC650
This sign on the package means that all used
electronic and electric equipment should not be
mixed with general household waste.
CHECK ALL CERTIFICATES
All newest certicates may be found in our Wiki2.
2 wiki.teltonika-gps.com/view/FMC650_Certication_%26_Approvals

Quick Manual v1.1 // FMC650 20
Telematics
WARRANTY
TELTONIKA guarantees its products to be free of any manufacturing defects for a period of 24 months. With additional agreement
we can agree on a dierent warranty period, for more detailed information please contact our sales manager.
Contact us teltonika-gps.com/about-us/contacts
All batteries carry a reduced 6 month warranty period.
If a product should fail within this specic warranty time, the product can be:
• Repaired
• Replaced with a new product
• Replaced with an equivalent repaired product fullling the same functionality
• TELTONIKA can also repair products that are out of warranty at an agreed cost.
WARRANTY DISCLAIMER
TELTONIKA PRODUCTS ARE INTENDED TO BE USED BY PERSONS WITH TRAINING AND EXPERIENCE. ANY OTHER USE RENDERS THE
LIMITED WARRANTIES EXPRESSED HEREIN AND ALL IMPLIED WARRANTIES NULL AND VOID AND SAME ARE HEREBY EXCLUDED.
ALSO EXCLUDED FROM THIS LIMITED WARRANTY ARE ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT
NOT LIMITED TO, LOSS OF USE OR REVENUE, LOSS OF TIME, INCONVENIENCE OR ANY OTHER ECONOMIC LOSS.
More information can be found at teltonika-gps.com/warranty-repair