Teltonika FM3001 Installation guide

Quick Manual
v1.2
Advanced OBDII tracker
FM3001

2
FM3001 | Wiki
Table of Contents
Know your device .......................................................................... 3
Pinout................................................................................................. 4
Set up your device......................................................................... 5
How to insert Micro-SIM card and connect the battery................ 5
PC Connection (Windows)................................................................ 6
How to install USB drivers (Windows)............................................. 6
Configuration (Windows) ................................................................. 6
Quick SMS configuration.................................................................. 8
LED indications .............................................................................. 9
Basic characteristics ..................................................................... 9
Safety information...................................................................... 11
Certification and Approvals ....................................................... 12
Warranty ...................................................................................... 13
Warranty Disclaimer ....................................................................... 13

3
FM3001 | Wiki
Know your device
Figure 1 FM3001 device view

4
FM3001 | Wiki
Pinout
Table 1 OBDII pinout
Pinnumber
Pinname
Description
2
PWM_BUS+/VPW
4
GND (-)
Ground
5
GND (-)
Ground
6
CAN_H
CAN high
7
K-Line
10
PWM_BUS-
14
CAN_L
CAN low
15
L-Line
16
VCC (10 - 30)V DC(+)
Power supply (+10-30 V DC)
Figure 2 FM3001 OBDII socket pinout

5
FM3001 | Wiki
Set up your device
How to insert Micro-SIM card and
connect the battery
1. Gently remove FM3001 cover using plastic pry tool from both
sides.
2. Insert Micro-SIM card as shown with PIN request disabled or
read our Wiki how to enter it later in Teltonika Configurator.
Make sure that Micro-SIM card cut-off corner is pointing
forward to slot.
3. Connect battery as shown to device. Position the battery in
place where it does not obstruct other components.’
4. Attach device cover back.
Device is ready to be connected.
Figure 3 Cover removal
Figure 4 Micro-SIM card insert
Figure 5 Battery connection
Figure 6 Attaching cover back

6
FM3001 | Wiki
PC Connection (Windows)
1. Power-up FM3001 with DC voltage (10 –30 V) power supply
using supplied power cable. LED’s should start blinking, see
“Quick SMS configuration
Default configuration has optimal parameters present to ensure
best performance of track quality and data usage.
Quickly set up your device by sending this SMS command to it:
Note: Before SMS text, two space symbols should be inserted.
GPRS settings:

2001
–APN
–APN username (if there
2002
are no APN username, empty
field should be left)
–APN password (if there
2003
are no APN password, empty
field should be left)
Server settings:
–Domain
2004
–Port
2005
–Data sending protocol
2006
(0 –TCP, 1 –UDP)
Default configuration settings
Movement and ignition detection:
Vehicle movement will
be detected by
accelerometer
Ignition will be detected
by vehicle power voltage
between 13,2 –30 V
Device makes a record On Moving if one of these events happen:
300 seconds passes
Vehicle turns 10 degrees
Vehicle drives 100
meters
Speed difference
between last coordinate
and current position is
greater than 10 km/h
Device makes a record On Stop if:
1 hour passes while
vehicle is stationary
and ignition is off
Records sending to server:
If device has made a
record it is sent to the
server every 120
seconds
After successful SMS configuration, FM3001 device will
synchronize time and update records to configured server.

7
FM3001 | Wiki
Time intervals and default I/O elements can be changed by using
Teltonika Configurator or SMS parameters.

8
FM3001 | Wiki
2. LED indications”.
3. Connect device to computer using Micro-USB cable or
Bluetooth connection:
Using Micro-USB cable
▬You will need to install USB drivers, see “How to install
USB drivers (Windows)”
Using Bluetooth
▬FM3001 Bluetooth is enabled by default. Turn on
Bluetooth on your PC, then select Add Bluetooth or
other device > Bluetooth. Choose your device named –
“FM3xxx_last_7_imei_digits”, without LE in the end.
Enter default password 5555, press Connect and then
select Done.
4. You are now ready to use the device on your computer.
How to install USB drivers
(Windows)
1. Please download COM port drivers from here.
2. Extract and run TeltonikaCOMDriver.exe.
3. Click Next in driver installation window.
4. In the following window click Install button.
Setup will continue installing the driver and eventually the
confirmation window will appear. Click Finish to complete the
setup.
Configuration (Windows)
At first FM3001 device will have default factory settings set. These
settings should be changed according to the user's needs. Main
configuration can be performed via Teltonika Configurator
software. Get the latest Configurator version from here.
Configurator operates on Microsoft Windows OS and uses
prerequisite MS .NET Framework. Make sure you have the correct
version installed.
Table 2 MS .NET requirements
MS.NETrequirements
Operating
system
MS .NET Framework
version
Version
Links
Windows Vista
Windows 7
Windows 8.1
Windows 10
MS .NET Framework
4.6.2
32 and 64 bit
www.microsoft.com
Downloaded Configurator will be in compressed archive. Extract it
and launch Configurator.exe. After launch software language can
be changed by clicking in the right bottom corner (Figure 7
Language selection).

9
FM3001 | Wiki
Configuration process begins by pressing on connected device
(Figure 8 Device connected via USB).
After connection to Configurator Status window will be displayed
(Figure 9 Configurator Status window).
Various Status window tabs display information about GNSS,
GSM,I/O, Maintenance and etc. FM3001 has one user editable
profile, which can be loaded and saved to the device. After any
modification of configuration the changes need to be saved to
device using Save to device button. Main buttons offer following
functionality:
1. Load from device –loads configuration from device.
2. Save to device –saves configuration to device.
3. Load from file –loads configuration from file.
4. Save to file –saves configuration to file.
5. Update firmware –updates firmware on device.
6. Read records –reads records from the device.
7. Reboot device –restarts device.
8. Reset configuration –sets device configuration to
default.
Most important configurator section is GPRS –where all your
server and GPRS settings can be configured and Data Acquisition
–where data acquiring parameters can be configured.
More details about FM3001 configuration using Configurator can
be found in our Wiki.
Figure 8 Device connected via USB
Figure 7 Language selection
Figure 9 Configurator Status window

10
FM3001 | Wiki
Quick SMS configuration
Default configuration has optimal parameters present to ensure
best performance of track quality and data usage.
Quickly set up your device by sending this SMS command to it:
Note: Before SMS text, two space symbols should be inserted.
GPRS settings:

2001
–APN
–APN username (if there
2002
are no APN username, empty
field should be left)
–APN password (if there
2003
are no APN password, empty
field should be left)
Server settings:
–Domain
2004
–Port
2005
–Data sending protocol
2006
(0 –TCP, 1 –UDP)
Default configuration settings
Movement and ignition detection:
Vehicle movement will
be detected by
accelerometer
Ignition will be detected
by vehicle power voltage
between 13,2 –30 V
Device makes a record On Moving if one of these events happen:
300 seconds passes
Vehicle turns 10 degrees
Vehicle drives 100
meters
Speed difference
between last coordinate
and current position is
greater than 10 km/h
Device makes a record On Stop if:
1 hour passes while
vehicle is stationary
and ignition is off
Records sending to server:
If device has made a
record it is sent to the
server every 120
seconds
After successful SMS configuration, FM3001 device will
synchronize time and update records to configured server.
Time intervals and default I/O elements can be changed by using
Teltonika Configurator or SMS parameters.
" setparam :APN;
2001
:APN_username;
2002
:APN_password;
2003
:Domain;
2004
:Port;
2005
;0"
2006