Teltonika RUT104 HSUPA User manual

2 | P a g e
LEGAL NOTICE
Copyright © 2012 TELTONIKA Ltd. All rights reserved. Reproduction, transfer, distribution
or storage of part or all of the contents in this document in any form without the prior written
permission of TELTONIKA Ltd is prohibited. The manufacturer reserves the right to modify the
product and manual for the purpose of technical improvement without prior notice.
Other product and company names mentioned herein may be trademarks or trade names of their
respective owners.
CE COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device.
CE mark declaration of conformity can be found at Teltonika WEB page www.teltonika.eu
ATTENTION
Before using the device we strongly recommend read this user
manual.
Do not rip the device. Do not touch the device if the device block
is broken or its connecting wires are without isolation.
All wireless devices for data transferring may be susceptible to
interference, which could affect performance.
The device is not water-resistant. Keep it dry.
The device requires high 230V AC voltage.
IMPORTANT NOTES!
It is mandatory to read the notes and manual carefully before starting to use the device.
TECHNICAL SUPPORT CONTACTS
If you face any problems related to the device, which you are not able to solve by yourself, you are
always welcome to address our technical support department by e-mail [e-mail]. We will
be very glad to help you.

3 | P a g e
Table of Contents
1SAFETY INFORMATION ........................................................................................................................5
2PRODUCT OVERVIEW............................................................................................................................6
2.1 Introduction .............................................................................................................................................6
2.2 Package contents .....................................................................................................................................6
2.3 System requirements...............................................................................................................................6
2.4 RUT104 Hardware, LED's and connections ......................................................................................7
2.4.1 Back panel......................................................................................................................................7
2.4.2 Front panel ....................................................................................................................................7
3GETTING STARTED.................................................................................................................................8
3.1 Initial setup...............................................................................................................................................8
3.2 Router installation guide.........................................................................................................................8
4ROUTER CONFIGURATION.................................................................................................................9
4.1 Connect to router WEB configuration page using wired connection.............................................9
4.2 Connect to router WEB configuration page using wireless connection...................................... 10
4.3 WEB configuration page interface structure.................................................................................... 11
4.4 Quick Setup........................................................................................................................................... 12
4.5 Status...................................................................................................................................................... 13
4.5.1 System Information................................................................................................................... 13
4.5.2 Hardware information .............................................................................................................. 14
4.5.3 Routes.......................................................................................................................................... 14
4.5.4 Kernel log ................................................................................................................................... 14
4.6 Configuration........................................................................................................................................ 15
4.6.1 Mobile Network Settings.......................................................................................................... 15
4.6.2 Network Settings ....................................................................................................................... 16
4.6.3 Wireless Settings ........................................................................................................................ 17
4.6.3.1 Hardware wireless settings.................................................................................................. 17
4.6.3.2 Software wireless settings.................................................................................................... 17
4.6.4 Dynamic DNS Settings............................................................................................................. 18
4.6.5 Services........................................................................................................................................ 19
4.6.5.1 SSH......................................................................................................................................... 19
4.6.5.2 HTTP..................................................................................................................................... 19
4.7 VPN ....................................................................................................................................................... 20
4.7.1 OpenVPN (site to site )............................................................................................................ 20
4.7.1.1 Server configuration............................................................................................................. 21
4.7.1.2 Client configuration ............................................................................................................. 22
4.7.2 GRE Tunnel............................................................................................................................... 23
4.7.3 IPsec ............................................................................................................................................ 24
4.7.3.1 Manual IPSec Key exchange .............................................................................................. 24
4.7.3.2 Automatic IPSec Key exchange......................................................................................... 25
4.8 Admin .................................................................................................................................................... 26
4.8.1 Account....................................................................................................................................... 26
4.8.2 NTP............................................................................................................................................. 26
4.8.3 Firmware upgrade...................................................................................................................... 27
4.9 Firewall................................................................................................................................................... 27
4.9.1 Port forwarding.......................................................................................................................... 30
4.9.2 DMZ............................................................................................................................................ 30
4.10 Tools ................................................................................................................................................. 31
4.10.1 Site Survey .................................................................................................................................. 31
4.10.2 Ping Reboot................................................................................................................................ 31
4.10.3 Diagnostics ................................................................................................................................. 32
4.11 Reboot and Logout......................................................................................................................... 32
5TECHNICAL SPECIFICATION........................................................................................................... 33

4 | P a g e
6Appendix A Configuring PC wireless security........................................................................................ 35
7Appendix B Changing router IP address................................................................................................. 37
8Appendix D Accessing RUT from the WEB ......................................................................................... 38
9Appendix E SIM card public or private IP address............................................................................... 39

5 | P a g e
1 SAFETY INFORMATION
In this document you will be introduced how to use 3G Mobile Router safely. We suggest you
to adhere to following recommendations to avoid any damage to person or property.
You have to be familiar with the safety requirements before starting to use the device!
3G Mobile Router is used to provide a mobile Internet access using a GSM network. To avoid burning
and voltage caused traumas, of the personnel working with device, please follow these safety
requirements.
Device requires power supply source that satisfies all safety
requirements listed in LST EN 60950-1 standard. Each power
supply source should not exceed 15VA.
The PC and power supply source, to which the device is
connected, should satisfy LST EN 60950-1 standard. The device
can be used on first (Personal Computer) or second (Notebook)
computer safety class.
Disconnect device from power supply before mounting to avoid
voltage effect!
Do not mount or serve device during a thunderbolt.
To avoid mechanical damages of the device it is recommended to transport the device packed
in damage-proof pack. While using the device, it should be placed so, that its indication LED would be
visible as they inform in which working mode the device is and if it has any working problems.
Protection against over currents, short circuits and earth faults should be provided as a part of
the building installation. Two pole protective device is required to protect from short-circuit and earth
false. The power of connected device should satisfy power of release device. To disconnect the device
plug off AC/DC power adapter from the wall outlet or power strip. The interstice between contacts
should be no less than 3mm.
Signal level of the device depends on the environment in which it is working. If the device
starts working insufficiently only qualified personnel may repair this product. We recommend to
forward it to repair centre or to manufacturers. No exchangeable parts inside of the device.

6 | P a g e
2 PRODUCT OVERVIEW
2.1 Introduction
Teltonika 3G Mobile Router provides WAN connectivity to wired and wireless clients using the
3G cellular data network. It allows multiple users to get IEEE 802.11 compliant connection within
your wireless broadband network with a single 3G data access account and SIM card. 3G Mobile
Router is extremely useful for mobile work teams or emergency crews that need access to the
broadband Internet but have no permanent base. The 3G/IEEE 802.11 router might be an easy
solution to provide Internet connection for commuter vehicles, such as trains or company buses.
Quickly set up a IEEE 802.11 hotspot Internet connection to check email and browse the web or share
files.
2.2 Package contents
RUT104
3G Mobile Router
2 external Wireless LAN antennas
2 External GSM antennas
Power adapter
CAT5 LAN cable
Leaflet “Quick Start Guide”
Note: The manufacturer does not supply the SIM card, which is mandatory for setting up a
connection to the GSM network! The SIM card may be purchased from your GSM (mobile) service
provider!
Note: Using a power supply with a different voltage rating than the one included with the
RUT104 will cause damage and void the warranty for this product.
Note: If any of the components is missing or damaged, please contact the retailer or reseller
from which this product was purchased.
2.3 System requirements
A computer with Windows®, Macintosh®, or Linux-based operating systems with a network
connection (wired or wireless).
A web browser Internet Explorer 6.0, Netscape Navigator™ 6.0, Opera 9.0, Mozilla 5.0 or later
versions for configuration.

7 | P a g e
2.4 RUT104 Hardware, LED's and connections
2.4.1 Back panel
Figure 1. Router back panel view.
1. Main GSM antenna connection.
2. Wireless LAN antenna connection.
3. Aux GSM antenna connection.
4. Wireless LAN antenna connection.
2.4.2 Front panel
Figure 2. Router front panel view.
1. GSM LED.
A solid light indicates proper connection of the 3G.
2. Reset button.
3. Ethernet socket.
4. Ethernet LED. A solid light indicates proper connection of the Ethernet. A blinking light
indicates data transfer.
5. Power LED. A solid light indicates a proper connection to the power supply.
6. SIM card socket.
7. Power supply adapter socket.

8 | P a g e
3 GETTING STARTED
3.1 Initial setup
3G Mobile Router enables to access network using a wireless connection from virtually
anywhere within the operating range of wireless network. Some things should be considered before
finding place to set up access point:
1. Make sure the power outlet is nearby as the router requires power supply.
2. Keep the access point as central in work area as possible.
3. The number of walls and ceilings between the router and other network devices should be kept
to a minimum as each wall or ceiling probably will reduce adapter’s range from 1-30 meters.
Signal strength and speed fall off with distance.
4. Higher is often better. Set up the router on the top shelf of a bookcase rather than the bottom
one, if it is possible. The antenna usually works best if oriented to point straight up.
5. Building materials make a difference. A solid metal door or aluminum studs may have a
negative effect on range. Try to position access point and computers so that the signal passes
through drywall or open doorways. Materials and objects such as glass, steel, metal, walls with
insulation, mirrors, file cabinets, bricks, and concrete will degrade wireless signal.
6. Keep router away (at least 1-2 meters) from electrical devices or appliances that generate RF
noise.
7. If you are using 2.4GHz cordless phones or other wireless products your wireless connection
may degrade dramatically or drop completely. Make sure your 2.4GHz phone base is as far
away from your wireless devices as possible. The base transmits a signal even if the phone in
not in use.
3.2 Router installation guide
1. Attach Wireless LAN and GSM antennas.
Remove the antenna from its plastic wrapper.
Screw the antenna in a clockwise direction to the back panel of the unit.
Position the antenna upward at its connecting joint. This will ensure optimal reception.
2. Insert the SIM card which was given by your GSM (mobile) service provider.
3. Insert the Ethernet cable into LAN Port if the router will be configured using wired
connection.
4. Connect the power adapter to the socket on the front panel of 3G Mobile Router. Then plug
the other end of the power adapter into a wall outlet or power strip.
Note: SIM card is mandatory for setting up connection to the GSM network. However, the
manufacturer of this equipment does not supply the SIM card. The SIM card can be purchased from
your GSM (mobile) service provider! For APN, user name and password please contact your GSM
(mobile) service provider. The 3G Mobile Router must be powered off while inserting or taking out the
SIM card.

9 | P a g e
4 ROUTER CONFIGURATION
4.1 Connect to router WEB configuration page using wired connection
Step 1 Connect 3G Mobile Router to your PC using LAN cable.
Step 2 Setup Local Area Network adapter on your
computer (Go to Start > Settings > Network Connections
Right click on Local Network Connection select
Properties)
Step 3 Setup the Local Area network adapter’s IP address.
Choose Internet Protocol (TCP/IP) and click Properties.
Setup the Local area network adapter to
Obtain an IP address automatically and
Obtain DNS server address automatically
Note: It is possible to assign manually static IP address within
192.168.0.2 - 192.168.0.254 address range with mask 255.255.255.0,
gateway 192.168.0.1 and DNS server 192.168.0.1.
Step 4 Open the Web browser and type the IP address of the router (Default : 192.168.0.1) and
enter the 3G Mobile Router administrator login details to access the Web management tool:
The default administrator login settings are:
Login: admin
Password: admin01
Note: It is strongly recommended to change the password after the first router configuration.
Step 5 After successful administrator log on you will see the main page of the 3G Mobile
Router Web configuration interface. The device now is ready for configuration.

10 | P a g e
4.2 Connect to router WEB configuration page using wireless connection
Note: the Wireless network function is shipped disabled by default and the configuration for
the first time can be made only by using wired connection.
Step 1 Setup wireless network adapter on your
computer (Go to Start>Settings>Network
Connections>Right click on Wireless Network
Connection associated with the wireless adapter and
select Properties):
Step 2 Setup the wireless network adapter’s IP address
(choose Internet Protocol (TCP/IP) and click Properties):
Setup the wireless network adapter to
Obtain an IP address automatically and
Obtain DNS server address automatically
Note: It is possible to assign manually static IP address within
192.168.0.2 - 192.168.0.254 address range with mask 255.255.255.0,
gateway 192.168.0.1 and DNS server 192.168.0.1.
Step 3 Enable the wireless network connection.
Right click on Wireless Network Connection and chose
Enable.
Step 4 Choose the wireless network (default: www.teltonika.lt) from the list of available wireless
networks.
Step 5 Open the Web browser and type the device IP address (default 192.168.0.1) and enter
the 3G Mobile Router administrator login details to access the Web management.
The default administrator login settings are:
Login: admin
Password: admin01
Step 6 After successful administrator log on you will see the main page of the 3G Mobile
Router Web configuration interface. The device now is ready for configuration.

11 | P a g e
4.3 WEB configuration page interface structure
The main Web management menu is displayed after successful login into the system (Figure 3).
From this menu all essential configuration pages are accessed.
Figure 3. Main Management Menu
By default the Quick Setup menu is activated. The web management menu has the following
structure:
Quick Setup –quick router configuration wizard.
Status
System Information –displays general information of the device status.
Hardware information –displays device hardware information.
Routes –displays the rules which are currently active on this system.
Kernel log –displays the information about device kernel activity.
Configuration
Mobile Network Settings
Network Settings
Wireless Settings
Dynamic DNS Settings
Services –SSH, HTTPS services management.
VPN
OpenVPN –Create site to site tunnel or site to multi site tunnels.
GRE Tunnel –Create GRE tunnel.
IPsec –IPsec client settings.
Admin
Account –change administrator’s password.
NTP –Time and time synchronization settings.
Firmware upgrade
Firewall
General settings –General settings for your network interfaces to control network
traffic flow.
Traffic Rules –Defines policies traveling between different zones.
Port Forwarding
Custom Rules –Allow to execute arbitrary iptables commands which are not
otherwise covered by the firewall framework.
Tools
Site Survey –shows information about wireless networks in the local geography.
Ping Reboot –set up continuous ping IP address with possibility to automatically
reboot router if no echo received.
Diagnostics –Network utilities such as “Ping”, “Traceroute” and “Nslookup” to
diagnose the network connection.

12 | P a g e
4.4 Quick Setup
Use Quick Setup to quickly configure basic 3G Mobile Router settings. The configuration is
made in four steps (this is the default page when accessing the administration web management
interface).
To start quick setup wizard click button QUICK SETUP.
Step 1. Change router network settings if needed, if not, then leave as it is.
Step 2. Configure mobile network settings. The configuration data should be provided by your
ISP (Internet Service Provider).
Step 3. Configure wireless network settings.
It is recommended to use WPA-PSK with TKIP or AES data encryption. The passphrase for
data encryption may be 8-63 characters long and can include symbols (!?*&_) and spaces. This
passphrase must be the same as Network key in the PC wireless network security settings. If encryption
is chosen do not forget to configure your PC settings (refer to Appendix A).
Note: If No Encryption will be chosen it will let anyone within the range and with proper
equipment to connect to your network.

13 | P a g e
Step 4. After successful configuration please click button and then click the
button.
The router will reboot and start up with new settings. The process will take several minutes.
4.5 Status
4.5.1 System Information
System Information menu displays general devices status.
Figure 4. System Information
Connection information –displays the GSM network information
Local Network Information –displays local network configuration.
Wireless Information –displays wireless network information.

14 | P a g e
4.5.2 Hardware information
Figure 5. Hardware information
Uptime –displays the time since the system was last rebooted.
Firmware version –displays current version of the firmware.
Average system load –displays the average load of the device processor in the period of the
last 1 minute, 5 minutes and 15 minutes (a larger value means a larger average load on the processor:
<1.0 –System is idle; =1.0 –Normal load; >1.0 –Processor is busy).
LAN MAC address –displays wired LAN MAC address.
WLAN MAC address –displays wireless LAN MAC address.
Memory –displays total, free, cached and buffered system memory.
4.5.3 Routes
Figure 6. Routes information
ARP –ARP Table shows map of the IP addresses assigned to the MAC addresses.
Active IPv4-Routes –shows the active LAN and WAN routes.
4.5.4 Kernel log
The Kernel log displays the information about device kernel activity.
Figure 7. Kernel log information

15 | P a g e
4.6 Configuration
4.6.1 Mobile Network Settings
To set up the GSM connection SIM card is required. SIM card is not supplied with the router.
It may be purchased from internet service provider.
The following information to connect to the internet is required:
1. APN. Access Point Name (APN).
2. PIN. SIM card PIN number.
3. Authentication method. The authentication protocol, which is used by your Internet
Service Provider [None, CHAP or PAP].
4. User Name. If GSM operator does not require username, leave it blank.
5. Password. If GSM operator does not require password, leave it blank.
6. Enable manual DNS. If GSM operator does not require manual DNS, leave it disabled.
7. DNS server 1. If GSM operator does not require DNS server 1, leave it blank.
8. DNS server 2. If GSM operator does not require DNS server 2, leave it blank.
Warning: It is strongly recommended to use SIM card with PIN disabled. Otherwise, if the
entered PIN will be wrong, the SIM card will be locked.
Figure 8. Mobile network configuration.
APN –Access Point Name (APN)
PIN –SIM card pin number.
Authentication method –Select authentication type PAP, CHAP or None.
User Name –Enter your User Name for your mobile connection.
Password –Enter your Password for your mobile connection.
Enable Manual DNS –check to enter custom DNS server IP addresses
DNS server 1 and DNS server 2 are ISP domain servers.

16 | P a g e
4.6.2 Network Settings
This section will allow you to change the local network settings of the router and to configure
the DHCP settings
Figure 9. Network settings.
Router IP address. The IP address of the router. The default IP address is 192.168.0.1.
Subnet mask. The Subnet Mask of the router. The default subnet mask is 255.255.255.0.
Enable DHCP server. Check the box to enable the DHCP server on your router. Uncheck to
disable this function
Enabled DHCP server allows configuring IP addresses pool that will be assigned by the router.
Figure 10. Network settings.
IP address from. Starting IP addresses for the DHCP server’s IP assignment.
IP address to. Ending IP addresses for the DHCP server’s IP assignment.
Lease time. Determines how long IP addresses are assigned for you. During the lease time,
the DHCP server cannot assign that IP address to any other clients. The purpose of a lease is to limit
the length of time that a client may use an IP address. A lease prevents unused clients from taking up
IP addresses when there are more clients than addresses. Enter the Lease time in seconds.
WINS address. If WINS (Windows Internet Naming Service ) server is specified, the router
at system startup, will register its name and IP address with the WINS server. WINS server is used for
mapping host names to network addresses. This results in fast and efficient host name resolution.
Specify WINS server IP address.
Domain. Enter the domain name for the Router. Some ISP's require it for identification.
Check your ISP to see if your broadband Internet service has been configured with a domain name. In
most cases, leaving these fields blank will work.

17 | P a g e
4.6.3 Wireless Settings
4.6.3.1 Hardware wireless settings
Figure 11. Wireless network settings.
Enable radio. Check the box to enable the wireless function. If you do not want to use
wireless network, uncheck the box to disable the wireless function.
IEEE mode. Specify the wireless network mode [B, G, mixed B/G, G Dynamic Turbo].
Channel. Select the channel for the wireless network.
Transmit power. Set the maximum transmitter radiation power.
4.6.3.2 Software wireless settings
Figure 12. Wireless network settings.
SSID. Specify a unique name for your wireless network.
Fragmentation. Specify the fragmentation threshold (in bytes), which determines whether data
frames will be fragmented and at what size [256-2346/off/auto]. On the 802.11 wireless LAN, frames
exceeding the fragmentation threshold will be fragmented, i.e., split into smaller units suitable for the
circuit size. Data frames smaller than the specified fragmentation threshold value are not fragmented.
Default: off.
RTS. Specify the maximum packet size beyond which the wireless LAN card invokes it’s
RTS/CTS mechanism [0-2347/off/auto]. Packets that exceed the specified RTS threshold trigger the
RTS/CTS mechanism. The card transmits packets smaller than this threshold without using RTS/CTS.
Default: off.
Fast Frames. Packet aggregation and timing modifications. Default: off.
Packet Bursting. More data frames per given time period. Default: off.
Compression. Standards based (Lempel Ziv) real-time hardware compression. Default: off.
Quality of service (WMM). Check the box to enable applications such as audio, video and
voice to have higher priority than less-sensitive data applications.
User isolation. Check the box to isolate the wireless clients from communicating with each
other.
Hide ESSID. Hides the wireless LAN SSID. Default: off.

18 | P a g e
Encryption. Choose the authentication method for wireless network:
No Encryption. It will let anyone within range and with the proper equipment to connect
onto your network within the router operating range.
WEP Open System –choose the 64 bit WEP security with one of four pre-shared keys.
WEP Shared Key–choose the 128 bit WEP security with one of four pre-shared keys.
WPA-PSK –choose the WPA security with pre-shared key.
WPA2-PSK –choose the WPA2 security with pre-shared key.
WPA-PSK/WPA2-PSK Mixed mode –choose for the coexistence of WPA and WPA2
clients in.
WPA-EAP –choose to enable the certificate based authentication.
WPA2-EAP –choose to enable the certificate based authentication.
Cipher. Choose the encryption method:
Auto. Encryption method is chosen by device.
Force CCMP (AES). Encryption by the AES algorithm.
Force TKIP. Encryption by the TKIP (Temporal Key Integrity Protocol) algorithm.
Note: Setting a lower fragmentation threshold value can help improve connection reliability in
noisy environments (where radio interference is present). This mechanism does add overhead and
therefore reduces effective throughput.
Note: Setting a lower RTS threshold value can improve connection reliability and throughput
in crowded wireless LAN environments (where many clients are trying to communicate
simultaneously). It adds a certain amount of overhead, but can compensate for this by reducing
bandwidth lost due to collisions.
4.6.4 Dynamic DNS Settings
Dynamic DNS (DDNS) is a domain name service allowing to link dynamic IP addresses to
static hostname. To start using this feature firstly you should register to DDNS service provider.
Figure 13. Dynamic DNS Settings.
Enable Dynamic DNS –check the box to enable DDNS.
User name - enter your user name. The router will use it to automatically login to update your
IP address in the DDNS server.
Password –enter you login password.
Hostname - enter your hostname which was registered in DDSN server.
Update period –enter IP address update time in seconds.
DynDNS service type –DYNDNS service type. Allowed are all DynDNS service types

19 | P a g e
4.6.5 Services
In this section HTTP, SSH services which are important for remote control monitoring and
management may be enabled and disabled.
4.6.5.1 SSH
Figure 14. SSH service configuration
Enable SSH. Check the box to enable SSH service.
Port. Set port value of the SSH service.
Enable access form WAN. Check the box to enable access via SSH from WAN
4.6.5.2 HTTP
Figure 15. HTTP service configuration
Enable HTTP access from WAN. Check the box to enable management though HTTP from
WAN.
HTTP port override. Set port number for the HTTP management from WAN.
Enable HTTPS access from WAN. Check the box to enable management though HTTPS
from WAN.
HTTPS port override. Set port number for the HTTPS management from WAN.

20 | P a g e
4.7 VPN
4.7.1 OpenVPN (site to site )
OpenVPN site to site graphical user interface (GUI) implementation allows connecting two
remote networks via point-to-point encrypted tunnel. OpenVPN implementation offers a cost-effective
simply configurable alternative to other VPN technologies. The OpenVPN security model is based on
SSL, the industry standard for secure communications via the internet. OpenVPN implementation uses
OSI layer 2 secure network extension using the SSL/TLS protocol. The typical VPN site to site
implementation using OpenVPN is presented in Figure 16.
OpenVPN tunnel
Internet
Tunnel IP 10.0.0.1 Tunnel IP 10.0.0.2
Network IP
192.168.0.0/24
192.168.0.2
Network IP
192.168.1.0/24
LAN2 192.168.1.2
Remote Endpoint IP
xxx.xxx.xxx.xxx
Server Client
Figure 16. Typical site to site OpenVPN tunnel configuration
Server configuration
Client configuration
Remote Endpoint IP
xxx.xxx.xxx.xxx
Local tunnel IP
10.0.0.1
Local tunnel IP
10.0.0.2
Remote tunnel IP
10.0.0.2
Remote tunnel IP
10.0.0.1
Remote network IP
192.168.1.0
Remote network IP
192.168.0.0
Remote network
subnet mask
255.255.255.0
Remote network
subnet mask
255.255.255.0
The OpenVPN implementation requires server to have public IP or hostname. Also the remote
network subnets must be different as in Fig. 23 192.168.0.0/24 and 192.168.1.0/24. If the subnet will
be the same tunnel will not be created or may not function correctly due to routing rules.
The server and client have almost the same configuration. The difference in the client
configuration is the remote endpoint IP or hostname field. Also the client can set up the keep alive
settings. For successful tunnel creation a static key must be generated on one side and the same key
must be uploaded on the opposite side.
Figure 17. OpenVPN instances
Role –Select “Client” or “Server” role for the device.
New configuration name –Set the name for OpenVPN configuration.
Edit –Press Edit button to edit the OpenVPN configuration.
Delete –Press Delete button to delete the OpenVPN configuration.