tema AD699/L10M User manual

Multicolor LED flas
hing
AD699/L10M
“
IP COMMUNICATION AND SECURITY COMP
ANY
”
AD699
/L10M
-
SEGN
-
MULTICOLORE
-
2
203
*
Product pecification may change without notice
*
WWW.TEMATLC.IT
1
Technical Features
Supply voltage DC : 12Vdc – 24Vdc
Supply voltage AC : 12Vac – 18Vac
Power : 2,5W-5W
Temperature : -20° +60°
Protection grade : IP56
Diffu ion cap color : White
LED : 6 Multicolor LED , 6 White LED
Functionality : teady or fla hing light, with pr
ogramming
button
AD699/L10M Multicolor LED fla hing
Installation
● In tall the fla her on a mooth and flat urface o that the rear ga ket fit nugly
● Clean the back of the box from du t or grea e
● Apply the adhe ive ga ket o that it eal the edge of the expo ed area
● Pre the ga ket o that the adhe ive adhere perfectly to the box
● Fix the box o that it i pre ed a much a po ible on the in tallation urface
● If nece ary, eal the expo ed printed circuit area (where there i the input terminal block) and the
re t of the
box with ilicone
● Clo e the tran parent cover tightly by turning it clockwi e
Note: image are indicative and may vary according to production
The AD699/L10M light indicator allow you to emit light with programmable
color and intermittent emi ion, which are al o programmable through 2
button which can be acce ed by unlocking the cover with a clockwi e rota-
tion. The following
7 color can be elected: white, red, green, blue, light
blue, yellow, pink. Activation can be programmed imply by powering the in-
dicator with a voltage from 9V to 24V in direct or from 9 to 18V in alternat-
ing. It i po ible to keep the module powered at
re t and provide a contact
from the out ide on a pecific terminal. During the programming pha e, by
etting up a pecial internal witch, the brightne of the LED i reduced o
a not to di turb the operator, at the end of the programming the normal
brightne will be re tored.

Multicolor LED flas
hing
AD699/L10M
“
IP COMMUNICATION AND SECURITY COMP
ANY
”
AD699
/L10M
-
SEGN
-
MULTICOLORE
-
2
203
*
Product pecification may change without notice
*
WWW.TEMATLC.IT
2
UNI EN ISO 9001:2015
TEMA TELECOMUNICAZIONI
S.r.l.
Via Costante Girardengo, 1/4 - 20161 Milano MI (Italy) Tel. [phone] Fax [phone]
Web: www.tematlc.it e-mail: [e-mail] International: [e-mail]
Never look at the illuminator at clo e range without cover, po ible eye damage
Programm
ing
● Set dip witch 8 to the ON po ition (All the other witche have no effect)
● The ervice blue LED will light up and the brightne of the indicator LED will be lowered
● Pre and relea e button PL1 to change the equence until the de ired one i obtained
● Pre and relea e the PL2 button to vary the color until the de ired color i obtained
● Pre and HOLD the PL1 button until the blue ervice LED fla he quickly, then relea e button PL1: the program-
ming ha been tored. If you don't do thi , the programming will NOT tored
● Return dip witch 8 to the OFF po ition
●
The blue ervice LED will fla h for about 10 econd to allow clockwi e coupling of the cover, then the indicator
LED , if activated, will return to full brightne
When turned on, the indicator repeat the la t programming that wa tored in the internal Fla h memory. It i
po ible to choo e both a fla hing equence and one of the 7 available color .
The PL1 button allow the choice of the fla hing equence.
The PL2 button allow the choice of one of the 7 color : White, Green, Red, Blue, Yellow, Light blue, Pink.
BLUE
LED
ff
N
1
8
+12
-
24V
-
GND
A
B
External
contact or A-
B jumper
Ways of using
● Device powered on JEX1 terminal with activation from external contact on JEX2
● Device powered with 12-24V only upon activation, make a jumper between A-B of JEX2