Tenda Multifunctional Broadband Router User manual

Multifunctional Broadband Router User Guide
Copyright Statement
is the registered trademark of Shenzhen Tenda
Technology Co., Ltd. Other trademark or trade name
mentioned herein are the trademark or registered trademark
of above company. Copyright of the whole product as
integration, including its accessories and software, belongs to
Shenzhen Tenda Technology Co., Ltd. Without the permission
of Shenzhen Tenda Technology Co., Ltd, individual or party is
not allowed to copy, plagiarize, imitate or translate it into other
languages.
All the photos and product specifications mentioned in this
manual are for references only, as the upgrading of software
and hardware, there will be changes. And if there are changes,
Tenda is not responsible for informing in advance. If you want
to know more about our products information, please access
our website at www.tenda.cn

Multifunctional Broadband Router User Guide
Contents
Contents................................................................................1
1.1 Hardware Installation ............................................................ 1
1.2 LED Indicators on Rear Panel .............................................. 2
1.3 Topology................................................................................. 2
Chapter Two Configuration Guide ......................................3
2.1 To configure the network on your PC correctly.................. 3
2.2 To check the connection....................................................... 5
2.3 Log in the Router................................................................... 6
2.4 Get to Know the Management Interface .............................. 7
2.5 Quick Installation Guide........................................................ 8
2.6 Status.................................................................................... 11
2.7 Wizard................................................................................... 11
2.8 Advanced Config ................................................................. 12
2.9 DHCP Server ........................................................................ 16
2.10 Virtual Server ..................................................................... 17
2.11 Security Setting ................................................................. 21
2.12 Routing Setting.................................................................. 28
2.13 System Tool ....................................................................... 29
Package Contents ..................................................................... 34
Physical Environment ............................................................... 34

Multifunctional Broadband Router User Guide
Chapter One Hardware Installation
Rear Panel Port Details
4 10/100M LAN
Ports
Connect to 10/100Base-T Ethernet LAN Cards
or Uplink to Switch/Hub
RESET
Warning! When you press “RESET” up to 7
seconds, your configuration will be lost and the
router restores to factory default settings.
WAN Connect to XDSL/Cable Modem/Ethernet
AC9V AC 9V power Interface
1.1 Hardware Installation
1、Pleases use cable to connect LAN port of router with LAN adapter
of your PC or you can also connect the LAN port with switches or
Hubs in LAN
2、Please connect WAN port of router to internet with Cat. 5 cable
3、Please power on the router with specified adapter
1

Multifunctional Broadband Router User Guide
1.2 LED Indicators on Rear Panel
LED Indicators Details
POWER Indicates the status of the Power
SYS Blinking Indicates the device’s system goes well.
WAN Blinking
Indicates the WAN port is transmitting or
receiving data.
Always
ON
Indicates corresponding LAN port is connected
correctly.
LAN
(1/2/3
/4) Blinking Indicates the corresponding LAN port is
transmitting or receiving data.
1.3 Topology
Take 4-port broadband router as example. If you purchased 7/16-port
router, the LAN network can be established as the following topology.
2

Multifunctional Broadband Router User Guide
Chapter Two Configuration Guide
2.1 To configure the network on your PC correctly
1. Please click “My Network
Places” on your desktop and
select “Properties”.
2.Please right-click “Local
Area Connection” and select
“Properties”.
3. Please select “ Internet
Protocol(TCP/IP)” and click
“Properties”.
3

Multifunctional Broadband Router User Guide
4. On this page, there are two
options for IP settings : “Obtain
an IP address
automatically(O)” and “Use the
following IP address(S)”
A：If you select “Obtain an IP
address automatically(O)”,
please refer to the figure on the
right.
B：If you select “Use the
following IP address(S)”, you
have to input below
parameters respectively:
IP address:192.168.0.XXX
(XXX is among 2~254)
Subnet Mask: 255.255.255.0
Default gateway: 192.168.0.1
Also there are two ways for
DNS settings, Please select
“Use the following DNS server
addresses”.
Preferred DNS Server: Please
input the DNS server address
provided by ISP. Please
contact your ISP for this
information if you are not clear.
Alternate DNS Server: If you
have a secondary DNS Server
4

Multifunctional Broadband Router User Guide
address, please fill in this
blank.
After finishing above settings,
please click “OK” to submit
configuration, and click “OK” in
“Local Area connection” to
save configuration.
2.2 To check the connection
1.Click”Start------Program-----
Accessories----Command
Prompt”, you will see below
dialogue box.
2、Please input command
“Ping 192.168.0.1” and then
press “Enter”, If the screen
displays as the right Figure, it
shows your PC and router
have been connected
normally. Otherwise, please
check whether your router is
powered on or whether the
cable between your PC and
router is normally connected.
5

Multifunctional Broadband Router User Guide
2.3 Log in the Router
1. Please open IE and enter
“http://192.168.0.1” in the
address bar, then press “Enter”
2. Then right Figure will appear to
require User name and
Password, please enter as per
below factory default:
User Name: admin
Password: admin
Then click “OK”.
In order to have a faster access
to your router’s management
interface, please select
“Remember my password”
3. If the User name and
Password are correct, IE will
enter into administrator’s
interface as right Figure.
6

Multifunctional Broadband Router User Guide
2.4 Get to Know the Management Interface
1、After entering into the
configuration Interface, you will
see 9 function menus on the
left ,including: Status, Wizard,
Advanced Config, DHCP
Server, Virtual Server, Security
Setting, Routing Setting,
System Tool, Logout. Press the
separate button, you can
configure the function settings
respectively.
2、When selecting each Menu,
there will be a detailed setting
Figure appearing on the right
where you can configure in
details for each Menu.
7

Multifunctional Broadband Router User Guide
2.5 Quick Installation Guide
1、Click “Next” when you enter in
the “Welcome” interface.
2、Please select your Access
mode when you enter into
Wizard interface.
This Router supports 4 kinds of
Access modes:
Factory default Access mode is
“Dynamic IP”
A. If you select “ADSL Virtual
Dial-up(PPPoE)”, just enter the
User Name and Password,
provided by the ISP, into the
“Wizard ADSL” dialogue box.
For example, your ISP provided
you below User name and
password:
User name snake27653
[email protected]
Password 123snake
Then you have to fill in above
parameters as the figure on the
right.
8

Multifunctional Broadband Router User Guide
B. If you select “Ethernet
Broadband, automatically obtain
an IP from ISP (dynamic IP)”.
Please click “Save”.
C. If you select “Ethernet
Broadband, fixed IP provided by
ISP (fixed IP)”，figure on the right
will appear, you have to enter IP
address, Subnet-mask,
Gateway, DNS Server address
and Secondary DNS if available.
For example, your ISP provided
you below information:
IP
Address: 192.168.111.73
Subnet
-mask: 255.255.255.0
Gateway: 192.168.111.1
DNS
Server: 202.96.134.133
Secondary
DNS: 192.168.111.1
Then you have to fill in above
parameters as right Figure.
D. If you select “PPP Tunneling
Protocol (Can support
multi-protocol Virtual Private
Networks)(VPN)(PPTP).
PPTP Server: Including Domain
name and IP Address. You only
9

Multifunctional Broadband Router User Guide
need to fill in one of them.
PPTP Account: fill in with your
Account provided by your ISP.
PPTP Password: fill in with your
password provided by your ISP.
Address Moed:
a:If you select “Ethernet
Broadband, automatically obtain
an IP address from ISP(dynamic
IP)”, please click “Next” to finish
setting.
b: If you select “Ethernet
Broadband, fixed IP address
provided by ISP(Static IP)”,
Please click “Save” to save your
configuration
4、Running Status
After finishing above settings,
you can click “Status” menu on
the left to check the connection
status between your router and
ISP end.
10

Multifunctional Broadband Router User Guide
2.6 Status
This section will show you the Router’s running status.
The right Figure will show the
router’s running status.
This page shows the router’s
LAN port status (the router is
under default setting)
2.7 Wizard
Please refer to 2.5 for Quick
Installation Guide
11

Multifunctional Broadband Router User Guide
2.8 Advanced Config
LAN Settings
This page shows you the
detailed settings for LAN
ports.
1.MAC Address
This is router’s MAC
address that you can not
change.
2.IP Address: 192.168.0.1 is
the Router’s current IP
Address and Factory default IP
Address. You may change it if
necessary.
For example, you can change
the router’s IP address to
192.168.3.1.
Warning:
If you change this IP address,
you are required to use the
new IP address to log into the
12

Multifunctional Broadband Router User Guide
WEB Management Interface
so that you can successfully
access to the Internet.
Moreover, the default gateway
of all the computers under this
router is required to set as this
IP address.
WAN Setting
This page shows you the
detailed Settings for
WAN(PPPoE).
You can change the
parameters respectively for
different Access Modes. Taking
ADSL Access mode as
example, we may change
parameters as follows:
MTU
(Maximum
Transmission
Unit）
Service
Name
Some ISPs need
this to validate
customers’
information.
13

Multifunctional Broadband Router User Guide
Connect
Automatically,
Connect after
Start and Break
off.
Manual connect,
connect by user.
Connect when
needed,
Connect
automatically
when data
access.
Connec
tion
mode
Connect timing,
automatically
connect on the
appointed period
M
AC Address Clone
This page configures the MAC
Address for router’s WAN port.
This function enables you to
copy the Administrator’s LAN
Adapter MAC address as WAN
port MAC Address(you may
also change the MAC address
manually), but if you are not
14

Multifunctional Broadband Router User Guide
clear how to fill, you are
suggested to use this function.
For example, you may change
the WAN port to 00:00:56:76:
CC: A1 as setting on the right.
DNS
DNS (Domain Name System
service) Server distributes
Domain name address and IP
address for internet host.
Domain Name system will
translate Domain Name
address to IP address for
users.
Domain Name Service is an
Internet Tool to run Domain
Name System. The Server to
execute Domain Name Service
is called DNS Server which is
responding to Domain Name
Service’s demands.
15

Multifunctional Broadband Router User Guide
2.9 DHCP Server
DHCP Server
DHCP (Dynamic Host
Configure Protocol) can
distribute IP address, Subnet
mask, Gateway, DNS Server
IP Address and WINS IP
Address to clients
automatically. It enables
administrator to make
related settings for all PCs
under this router from the
Server rather than setting all
PCs one by one.
DHCP Client List
You can check the
connection status of client
through DHCP Client List
which includes IP Address,
MAC address, Lease Time
etc.
16

Multifunctional Broadband Router User Guide
2.10 Virtual Server
Virtual Server
1. Service Port: The service
port which the router offers to
WAN.
2. IP Address: The IP Address
of the computer in the LAN
which work as a virtual server.
3. Enable: Please select
“Enable” and the rules will go
into effect.
4. In “Service Port”, the
common port numbers are list
here. You could select one of
them and then select an ID in
“ID” and then press “Insert”,
and then the port would be
added to the list automatically.
For the port numbers which are
not displayed here, you could
fill it manually.
For example, the server in the
LAN with IP address of
192.168.0.10 offers WEB
service with port number of 80,
in order to enable visitors in the
Internet to have successful
access to this server, you
should configure as the figure
beside.
17

Multifunctional Broadband Router User Guide
Note:
If you configure a virtual
server (server port: 80), you
should configure the remote
WEB management in
“Wireless Security Configure”
as a value different from 80.
For example, you could set it
as 8080. Otherwise the
confliction would occur and the
server would not be able to
function. After you configure
the value in “Wireless Security
Configure”, you should reboot
the router to make the settings
go into effect.
DMZ Host
In certain special case, we
must make one of the LAN
computers completely using for
the internet to realize the dual
communication. Then you may
appoint the computer as the
Host. DMZ Host
18