Tennant 8410D User manual

8410D
*MM391*
www.tennantco.com
Operator Manual
MM391
Rev. 15 (05-2007)
North America / International
ES Extended Scrub System
R
The Safe Scrubbing AlternativeR

This manual is furnished with each new model. It provides necessary operation and maintenance instructions.
Read this manual completely and understand the machine before operating or servicing it.
This machine will provide excellent service. However, the best results will be obtained at minimum costs if:
SThe machine is operated with reasonable care.
SThe machine is maintained regularly - per the machine maintenance instructions provided.
SThe machine is maintained with manufacturer supplied or equivalent parts.
PROTECT THE ENVIRONMENT
Please dispose of packaging materials,
old machine components such as
batteries, hazardous fluids such as
antifreeze and oil, in an environmentally
safe way according to local waste
disposal regulations.
Always remember to recycle.
MACHINE DATA
Please fill out at time of installation for future reference.
Model No. --
Serial No. --
Machine Options --
Sales Rep. --
Sales Rep. phone no. --
Customer Number --
Installation Date --
Tennant Company
PO Box 1452
Minneapolis, MN 55440
Phone: [phone] or (763) 513--2850
www.tennantco.com
CALIFORNIA PROPOSITION 65 WARNING:
Engine exhaust from this product contains chemicals known to the State of California to cause cancer,
birth defects, or other reproductive harm.
Thermo--Sentry and FaST--PAK are US registered and unregistered trademarks of Tennant Company.
Specifications and parts are subject to change without notice.
Copyright E1996, 1997, 1999 -- 2006, 2007 TENNANT Company, Printed in U.S.A.

CONTENTS
1
8410D MM391 (6--05)
CONTENTS
Page
SAFETY PRECAUTIONS 3.................
OPERATION 7............................
OPERATOR RESPONSIBILITY 7.........
MACHINE COMPONENTS 8.............
SYMBOL DEFINITIONS 9................
CONTROLS AND INSTRUMENTS 11......
OPERATION OF CONTROLS 12..........
DIRECTIONAL PEDAL 12..............
BRAKE PEDAL 13....................
PARKING BRAKE PEDAL 13...........
HAZARD LIGHT SWITCH (OPTION) 13..
OPERATING LIGHTS SWITCH 14......
FILTER SHAKER SWITCH 14..........
HOPPER RAISE SWITCH 14...........
HOPPER DOOR SWITCH 15...........
HOPPER LOWER SWITCH 15.........
SIDE BRUSH SWITCH 15..............
SWEEP VACUUM FAN SWITCH 16.....
MAIN SWEEP BRUSH SPEED
1SWITCH 16......................
MAIN SWEEP BRUSH SPEED
2SWITCH 17......................
CHARGING SYSTEM LIGHT 17........
ENGINE OIL PRESSURE LIGHT 18.....
ENGINE WATER TEMPERATURE
LIGHT 18..........................
MAINTENANCE MODE LIGHT 18.......
RECOVERY TANK FULL LIGHT 18.....
CLOGGED FILTER LIGHT 19..........
HOPPER TEMPERATURE LIGHT --
THERMO SENTRY 19..............
OK LIGHT 19.........................
FUEL LEVEL GAUGE 20...............
HOURMETER 20.....................
ES SWITCH (OPTION) 20..............
DETERGENT FLOW SWITCH
(OPTION) 21......................
EDGE SCRUB SWITCH 21.............
SCRUB SWITCH 22...................
SQUEEGEE SWITCH 23...............
THROTTLE LEVER 23.................
STEERING WHEEL 24................
HORN BUTTON 24....................
IGNITION SWITCH 24.................
TURN SIGNAL SWITCH (OPTION) 25...
STEERING COLUMN TILT HANDLE 25..
CIRCUIT BREAKERS 26...............
MAIN SWEEP BRUSH DOWN
PRESSURE KNOB 27..............
SIDE BRUSH DOWN PRESSURE
KNOB 27..........................
SOLUTION FLOW SWITCH
(WITHOUT FaST) 27...............
SOLUTION FLOW SWITCH (FaST) 28..
FaST SWITCH 28.....................
Page
LATCHES 29.........................
FUSE 29.............................
OPERATOR SEAT 30..................
HOPPER SUPPORT BAR 30...........
HOW THE MACHINE WORKS 31..........
FaST SCRUBBING SYSTEM 32...........
PRE-OPERATION CHECKLIST 33.........
INSTALLING FaST PAK AGENT 34........
STARTING THE MACHINE 36.............
SWEEPING, SCRUBBING, AND BRUSH
INFORMATION 38....................
SWEEPING 40..........................
STOP SWEEPING 41....................
EMPTYING THE HOPPER 42.............
FILLING THE TANKS 44..................
SCRUBBING 46.........................
DOUBLE SCRUBBING 49.................
STOP SCRUBBING 49...................
DRAINING AND CLEANING THE TANKS 50
STOP THE MACHINE 52.................
POST-OPERATION CHECKLIST 54........
ENGAGING HOPPER SUPPORT BAR 55..
DISENGAGING HOPPER SUPPORT BAR 56
OPERATION ON INCLINES 57............
OPTIONS 58............................
VACUUM WAND (WET) 58.............
MACHINE TROUBLESHOOTING 61.......
MAINTENANCE 64.........................
MAINTENANCE CHART 64...............
LUBRICATION 66........................
ENGINE 66...........................
REAR WHEEL SUPPORT 66...........
FRONT WHEEL BEARINGS 67.........
HOPPER LIFT ARM PIVOTS 67........
HOPPER DOOR PIVOTS 67...........
REAR SQUEEGEE CASTERS (for
machines below serial
number 012215) 67..............
HYDRAULICS 68........................
HYDRAULIC FLUID RESERVOIR 68....
HYDRAULIC FLUID 68................
HYDRAULIC HOSES 69...............
PROPELLING MOTOR 69..............
ENGINE 70.............................
COOLING SYSTEM 70................
AIR FILTER INDICATOR 71............
AIR FILTER 71........................
FUEL FILTER 72......................
FUEL LINES 72.......................
PRIMING THE FUEL SYSTEM 72.......
BATTERY 73............................
BELTS AND CHAINS 74
..................
ENGINE BELT 74......................
STATIC DRAG CHAIN 74..............

CONTENTS
8410D MM391 (6--05)
2
Page
DEBRIS HOPPER 75.....................
HOPPER DUST FILTER 75.............
REMOVING HOPPER DUST
FILTER 75......................
THERMO SENTRY 77.................
SCRUB HEAD 77........................
BRUSHES 77............................
MAIN SWEEP BRUSH 77..............
REPLACING MAIN SWEEP BRUSH 78
CHECKING AND ADJUSTING MAIN
SWEEP BRUSH PATTERN 79....
SIDE BRUSH 81.........................
REPLACING SIDE BRUSH 82..........
SIDE BRUSH GUARD 82..............
SCRUB BRUSHES 83....................
REPLACING THE SCRUB BRUSHES 83
SOLUTION SYSTEM 84..................
RECOVERY TANK 84.................
SOLUTION TANK 84..................
FaST SYSTEM 85.....................
FaST SUPPLY HOSE CONNECTOR 85
FaST SYSTEM FILTER SCREEN 85..
FaST SYSTEM AIR PUMP FILTER 85
SQUEEGEES 86.........................
LEVELING THE REAR SQUEEGEE 86..
ADJUSTING REAR SQUEEGEE BLADE
DEFLECTION 87...................
SQUEEGEE BLADES 88.................
REAR SQUEEGEE 88.................
REPLACING OR ROTATING REAR
SQUEEGEE BLADES 88.........
SIDE SQUEEGEES 89................
REPLACING SIDE SQUEEGEE
BLADES 89.....................
SKIRTS AND SEALS 90..................
HOPPER LIP SKIRTS 90...............
HOPPER SIDE SKIRT 90..............
BRUSH DOOR SKIRTS 90.............
REAR SKIRTS 91.....................
BRUSH DOOR SEALS 91..............
HOPPER SEALS 91...................
HOPPER INSPECTION DOOR SEAL 91.
HOPPER DOOR SEALS 92............
HOPPER COVER SEAL 92.............
HOPPER DUST SEAL 92..............
HOPPER VACUUM FAN SEAL 92.......
COVER AND DOOR SEALS 93.........
BRAKES AND TIRES 93..................
SERVICE BRAKES 93.................
PARKING BRAKE 93..................
TIRES 93............................
REAR WHEEL 93.....................
PUSHING, TOWING, AND TRANSPORTING
THE MACHINE 94.....................
PUSHING OR TOWING THE MACHINE 94
TRANSPORTING THE MACHINE 95....
MACHINE JACKING 98...................
STORING MACHINE 98..................
Page
SPECIFICATIONS 99.......................
GENERAL MACHINE PERFORMANCE 99..
FaST SYSTEM 100.......................
POWER TYPE 100........................
STEERING 101...........................
HYDRAULIC SYSTEM 101.................
BRAKING SYSTEM 101...................
TIRES 101...............................
MACHINE DIMENSIONS 102...............
INDEX 103..................................

SAFETY PRECAUTIONS
3
8410D MM391 (9--02)
SAFETY PRECAUTIONS
The following precautions are used throughout
this manual as indicated in their description:
WARNING: To warn of hazards or
unsafe practices that could result in
severe personal injury or death.
FOR SAFETY: To identify actions that
must be followed for safe operation of
equipment.
The machine is suited to sweep disposable
debris. Do not use the machine other than
described in this Operator Manual. The machine
is not designed for use on public roads.
The following information signals potentially
dangerous conditions to the operator or
equipment:
WARNING: Engine emits toxic gases.
Severe respiratory damage or
asphyxiation can result. Provide
adequate ventilation. Consult with your
regulatory authorities for exposure
limits. Keep engine properly tuned.
WARNING: Raised hopper may fall.
Engage hopper support bar.
WARNING: Lift arm pinch point. Stay
clear of hopper lift arms.
WARNING: Moving belt and fan. Keep
away.
WARNING: Flammable materials can
cause an explosion or fire. Do not use
flammable materials in tank(s).
WARNING: Flammable materials or
reactive metals can cause explosion or
fire. Do not pick up.
WARNING: Strong vacuum. Keep away
from fan inlet when fan is running.
WARNING: Hot bumper. Keep away.
CALIFORNIA PROPOSITION 65
WARNING: Engine exhaust from this
product contains chemicals known to
the State of California to cause cancer,
birth defects, or other reproductive
harm.
FOR SAFETY:
1. Do not operate machine:
-- Unless trained and authorized.
-- Unless operator manual is read and
understood.
-- If it is not in proper operating
condition.
-- In flammable or explosive areas unless
designed for use in those areas.
-- In areas with possible falling objects
unless equipped with overhead guard.
2. Before starting machine:
-- Check for fuel, oil, and liquid leaks.
-- Keep sparks and open flame away
from refueling area.
-- Make sure all safety devices are in
place and operate properly.
-- Check brakes and steering for proper
operation.
3. When starting machine:
-- Keep foot on brake and directional
pedal in neutral.
4. When using machine:
-- Use brakes to stop machine.
-- Go slow on inclines and slippery
surfaces.
-- Use care when reversing machine.
-- Move machine with care when hopper
is raised.
-- Make sure adequate clearance is
available before raising hopper.
-- Do not carry passengers on machine.
-- Always follow safety and traffic rules.
-- Report machine damage or faulty
operation immediately.
-- Follow mixing and handling
instructions on chemical containers.
5. Before leaving or servicing machine:
-- Stop on level surface.
-- Set parking brake.
-- Turn off machine and remove key.

SAFETY PRECAUTIONS
8410D MM391 (9--02)
4
6. When servicing machine:
-- Avoid moving parts. Do not wear loose
jackets, shirts, or sleeves.
-- Block machine tires before jacking
machine up.
-- Jack machine up at designated
locations only. Block machine up with
jack stands.
-- Use hoist or jack that will support the
weight of the machine.
-- Wear eye and ear protection when
using pressurized air or water.
-- Disconnect battery connections before
working on machine.
-- Avoid contact with battery acid.
-- Avoid contact with hot engine coolant.
-- Allow engine to cool.
-- Keep flames and sparks away from
fuel system service area. Keep area
well ventilated.
-- Use cardboard to locate leaking
hydraulic fluid under pressure.
-- Use Tennant supplied or approved
replacement parts.
7. When loading/unloading machine
onto/off truck or trailer:
-- Turn off machine.
-- Use truck or trailer that will support
the weight of the machine.
-- Use winch. Do not drive the machine
onto/off the truck or trailer unless the
load height is 380 mm (15 in) or less
from the ground.
-- Set parking brake after machine is
loaded.
-- Block machine tires.
-- Tie machine down to truck or trailer.

SAFETY PRECAUTIONS
5
8410D MM391 (6--96)
The following safety labels are mounted on the
machine in the locations indicated. If these or any
label becomes damaged or illegible, install a new
label in its place.
HOPPER SUPPORT BAR LABEL -- LOCATED
ON THE HOPPER SUPPORT BAR AND ON
BOTH HOPPER LIFT ARMS.
ENGINE FAN AND BELT LABEL -- LOCATED
ON THE RADIATOR SHROUD.
EMISSIONS LABEL -- LOCATED ON THE SIDE
PANEL OF THE OPERATOR COMPARTMENT.
09078
FOR SAFETY LABEL -- LOCATED ON
THE SIDE PANEL OF THE OPERATOR
COMPARTMENT.
FLAMMABLE SPILLS LABEL -- LOCATED ON
THE SIDE PANEL OF THE OPERATOR
COMPARTMENT.

SAFETY PRECAUTIONS
8410D MM391 (6--96)
6
STRONG VACUUM LABEL -- LOCATED
ON THE VACUUM FAN HOUSING.
HOPPER LIFT ARMS LABEL -- LOCATED ON
BOTH HOPPER LIFT ARMS.
09078
FLAMMABLE MATERIALS
LABEL -- LOCATED ON THE
SOLUTION TANK COVER.
HOT BUMPER LABEL -- LOCATED ON THE
REAR LEFT PANEL.

OPERATION
7
8410D MM391 (6--96)
OPERATION
OPERATOR RESPONSIBILITY
-The operator’s responsibility is to take care
of the daily maintenance and checkups of
the machine to keep it in good working
condition. The operator must inform the
service mechanic or supervisor when the
required maintenance intervals occur as
stated in the MAINTENANCE section of this
manual.
-Read this manual carefully before operating
this machine.
FOR SAFETY: Do not operate machine,
unless operation manual is read and
understood.
-Check the machine for shipping damage.
Check to make sure machine is complete
per shipping instructions.
-Keep your machine regularly maintained by
following the maintenance information in this
manual. We recommend taking advantage
of a regularly scheduled service contract
from your Tennant representative.
-Order parts and supplies directly from your
authorized Tennant representative. Use the
parts manual provided when ordering parts.
-After the first 50 hours of operation, follow
the recommended procedures stated in the
MAINTENANCE CHART.
07324

OPERATION
8410D MM391 (6--05)
8
MACHINE COMPONENTS
ABC
D
E
F
G
H
I
J
K
L
M
N
O
09078
A. Instrument panels
B. Steering wheel
C. Operator seat
D. Engine cover
E. Engine side door
F. Rear squeegee
G. Solution tank
H. Side squeegee
I. Sweeping brush access door
J. Side brush
K. Hopper cover
L. ES pump cover
M. Tank cover
N. Recovery tank
O. FaST solution system

OPERATION
9
8410D MM391 (6--05)
SYMBOL DEFINITIONS
These symbols identify controls, displays, and
features on the machine:
Hazard light Recovery tank full
Operating lights Filter clogged
Filter shaker Hopper temperature -- Thermo Sentry
Hopper raise Diagnostics
Hopper door close Fuel
Hopper lower Hourmeter
Side brush down and on ES
Fan Detergent flow
Main brush down and speed 1 Scrub brush edge clean
Main brush down and speed 2 Scrub brushes down and on
Charging system Rear squeegee down and vacuum on
Engine oil pressure Jackpoint
Engine water temperature Horn
Maintenance mode Parking brake

OPERATION
8410D MM391 (9--97)
10
Solution flow Circuit breaker 5
Side brush down pressure light Circuit breaker 6
Side brush down pressure heavy Circuit breaker 7
Main sweep brush down pressure light Circuit breaker 8
Main sweep brush down pressure heavy Circuit breaker 9
Steering tilt Variable pressure
Circuit breaker 1 Diesel fuel only
Circuit breaker 2 Hydraulic fluid only
Circuit breaker 3 Fast
Circuit breaker 4 Off
Idle

OPERATION
11
8410D MM391 (6--05)
CONTROLS AND INSTRUMENTS
A
B
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
VWX
Y
ZAA
BB
CC
DD
EE
FF
GG
HH
II
JJ
C
KK
LL
10950
A. Directional pedal U. OK light
B. Brake pedal V. Fuel level gauge
C. Parking brake pedal W. Hourmeter
D. Hazard light switch (option) X. ES switch (option)
E. Operating lights switch Y. Detergent flow switch (option)
F. Filter shaker switch Z. Edge scrub switch
G. Hopper raise switch AA. Scrub switch
H. Hopper door switch BB. Squeegee switch
I. Hopper lower switch CC. Throttle lever
J. Side brush switch DD. Steering wheel
K. Sweep vacuum fan switch EE. Horn button
L. Main sweep brush speed 1 switch FF. Ignition switch
M. Main sweep brush speed 2 switch GG.Steering column tilt lever
N. Charging system light HH. Circuit breakers
O. Engine oil pressure light II. Main sweep brush down pressure
P. Engine water temperature light knob
Q. Maintenance mode light JJ. Solution flow switch
R. Recovery tank full light KK. FaST switch
S. Clogged filter light LL. FaST solution flow switch
T. Hopper temperature light --
Thermo Sentry

OPERATION
8410D MM391 (6--96)
12
OPERATION OF CONTROLS
DIRECTIONAL PEDAL
The directional pedal controls direction of travel
and the propelling speed of the machine. You
change the speed of the machine with the
pressure of your foot; the harder you press the
faster the machine travels.
Forward: Press the top of the directional pedal
with the toe of your foot.
Reverse: Press the bottom of the directional
pedal with the heel of your foot.
Neutral: Take your foot off the directional pedal
and it will return to the neutral position.
07790
07791
07792

OPERATION
13
8410D MM391 (6--96)
BRAKE PEDAL
The brake pedal stops the machine.
Stop: Take your foot off the directional pedal and
let it return to the neutral position. Step on the
brake pedal.
PARKING BRAKE PEDAL
The parking brake pedal sets and releases the
rear wheel brakes.
Set: Press on the brake pedal as far as possible,
then press on the parking brake pedal with the toe
portion of your foot to lock the parking brake pedal
in place.
FOR SAFETY: Before leaving or
servicing machine; stop on level
surface, set parking brake, turn off
machine and remove key.
Release: Press on the brake pedal to unlock the
parking brake pedal.
HAZARD LIGHT SWITCH (OPTION)
The hazard light switch powers on and off the
hazard light.
On: Press the hazard light switch. The indicator
light above the switch will come on.
Off: Press the hazard light switch. The indicator
light above the switch will go off.
07754
09293

OPERATION
8410D MM391 (6--96)
14
OPERATING LIGHTS SWITCH
The operating lights switch powers on and off the
headlights and taillights.
On: Press the operating lights switch. The
indicator light above the switch will come on.
Off: Press the operating lights switch. The
indicator light above the switch will go off.
FILTER SHAKER SWITCH
The filter shaker switch starts the hopper dust
filter shaker. The shaker automatically operates
for 40 seconds.
Start: Press the filter shaker switch. The indicator
light will remain on while the filter shaker is
operating.
NOTE: The filter shaker will operate automatically
for a short time when the sweeping operations are
stopped. The filter shaker will not operate while
the sweeping or vacuum system is operating.
HOPPER RAISE SWITCH
The hopper raise switch raises the hopper.
Raise: Press and hold the hopper raise switch.
The indicator light above the switch will come on.
Hold: Release the hopper raise switch.
WARNING: Raised hopper may fall.
engage hopper support bar.
NOTE: The main sweeping brush, side brush, and
sweep vacuum fan will stop operating when the
hopper is raised. If the sweep vacuum fan, side
brush switch, or either of the main brush switches
are pressed while the hopper is raised, the side
brush will not start and the hopper raise switch
indicator will blink.
09292
09294
09295

OPERATION
15
8410D MM391 (6--96)
HOPPER DOOR SWITCH
The hopper door switch opens and closes the
hopper door. Close the hopper door when
emptying the hopper to control debris and dust.
Open: Press the switch. The indicator light above
the switch will go out.
Close: Press the switch. The indicator light above
the switch will come on.
NOTE: The hopper door opens automatically
when the main sweeping brush starts operating,
and closes automatically when the machine is
started or if the main sweeping brush is not
operating.
HOPPER LOWER SWITCH
The hopper lower switch lowers the hopper.
Lower: Press and hold the hopper lower switch.
The indicator light above the switch will come on.
Hold: Release the hopper lower switch.
SIDE BRUSH SWITCH
The side brush switch controls the side brush
position and rotation. The main sweeping brush
must be operating for the side brush to work.
Down and On: Press the switch. The indicator
light above the switch will come on.
Up and Off: Press the switch again. The indicator
light above the switch will go off.
NOTE: The side brush operates automatically
when the main sweeping brush starts operating, if
the side brush switch is on.
NOTE: The side brush will not start if the hopper
is raised. If the side brush switch is pressed while
the hopper is raised, the side brush will not start
and the hopper raise switch indicator will blink.
09542
09543
09544

OPERATION
8410D MM391 (6--96)
16
SWEEP VACUUM FAN SWITCH
The sweep vacuum fan switch starts and stops
the sweep vacuum fan. Do not operate the
vacuum fan when sweeping in wet conditions.
Start: Press the switch. The indicator light above
the switch will come on.
Stop: Press the switch. The indicator light above
the switch will go off.
NOTE: The sweep vacuum fan operates
automatically when the main sweeping brush
starts operating. The sweep vacuum fan will not
turn on unless the main sweeping brush is
operating.
NOTE: The sweep vacuum fan will not start if the
hopper is raised. If the sweep vacuum fan switch
is pressed while the hopper is raised, the sweep
vacuum will not start and the hopper raise switch
indicator will blink.
MAIN SWEEP BRUSH SPEED 1 SWITCH
The main sweep brush speed 1 switch controls
the sweeping operation in normal speed.
The normal sweeping operations include the
following. The hopper door will open, the sweep
vacuum fan will come on, the side brush will lower
and start, and the engine speed will increase to
(Fast), and the main sweep brush will lower and
operate at normal speed. Speed 1 is used for
general sweeping.
Down and on: Press the switch. The indicator
light above the switch will come on.
Up and off: Press the switch again. The indicator
light above the switch will go off.
NOTE: The normal sweeping operations will not
start if the hopper is raised. If the main brush
normal speed switch is pressed while the hopper
is raised, the sweeping operations will not start
and the hopper raise switch indicator will blink.
NOTE: Always raise the main brush when the
machine is not being operated for some time. This
prevents the main brush from getting a flat spot.
09545
09546

OPERATION
17
8410D MM391 (6--96)
MAIN SWEEP BRUSH SPEED 2 SWITCH
The main brush speed 2 switch controls the
sweeping operation in litter speed.
The litter sweeping operations include the
following. The hopper door will open, the sweep
vacuum fan will come on, the side brush will lower
and start, and the engine speed will increase to
(Fast), and the main sweep brush will lower and
operate at speed 2. Speed 2 is used for sweeping
light litter.
Down and on: Press the switch. The indicator
light above the switch will come on.
Up and off: Press the switch again. The indicator
light above the switch will go off.
NOTE: The litter sweeping operations will not
start if the hopper is raised. If the main sweep
brush speed 2switch is pressed while the hopper
is raised, the sweeping operations will not start
and the hopper raise switch indicator will blink.
NOTE: The main sweep brush Speed 2switch
can not be operated while scrubbing. If the main
sweep brush is operating in speed 2 when the
scrubbing operations are started, the machine will
automatically change to main sweep brush to
speed 1.
NOTE: Always raise the main brush when the
machine is not being operated for some time. This
prevents the main brush from getting a flat spot.
CHARGING SYSTEM LIGHT
The charging system light comes on when the
alternator is not operating within normal range;
13.5 to 14.5 Volts. Stop operating the machine.
Locate the problem and have it corrected.
09558
10642

OPERATION
8410D MM391 (9--02)
18
ENGINE OIL PRESSURE LIGHT
The engine oil pressure light comes on when the
engine oil pressure falls below 40 kPa (5 psi).
Stop operating the machine. Locate the problem
and have it corrected.
ENGINE WATER TEMPERATURE LIGHT
The engine water temperature light comes on
when the temperature of the engine coolant is
more than 107_C (225_F). Stop operating the
machine. Locate the problem and have it
corrected.
MAINTENANCE MODE LIGHT
The maintenance mode light comes on when the
control panel diagnostic mode is manually
activated. The maintenance mode is for service
personnel use only. To clear the diagnostic mode,
turn the ignition key off.
RECOVERY TANK FULL LIGHT
The recovery tank full light starts blinking when
the recovery tank is full. The light will blink for
50 seconds and then stays on. Then the
scrubbing operations will shut off.
10643
10644
10645
10886