Tennant 607853 Product manual

Self-Contained Carpet Extractor
1220
Operator and Parts Manual
607860
Rev. 00 (11-99)
Model No.:
607853
FAX: [phone]
CUSTOMER SERVICE: 1–800-982–7658
TENNANT COMPANY
Commercial Products
12875 RANSOM STREET
HOLLAND MI 49424 U.S.A.

OPERATION
2Tennant 1220 (07–99)
This manual is furnished with each new model. It
provides necessary operation and maintenance
instructions and an illustrated parts list.
Read this manual completely and understand the
machine before operating or servicing.
Use the illustrated Parts Lists to order parts. Before
ordering parts or supplies, be sure to have your
machine model number and serial number handy.
Parts and supplies may be ordered by phone or mail
from any authorized parts and service center,
distributor or from any of the manufacturer’s
subsidiaries.
This machine will provide excellent service. However,
the best results will be obtained at minimum costs if:
The machine is operated with reasonable care.
The machine is maintained regularly - per the
maintenance instructions provided.
The machine is maintained with manufacturer
supplied or equivalent parts.
MACHINE DATA
Please fill out at time of installation for future reference.
ModelNo.-
Install. Date -
Serial No.-
1999 Tennant Company Printed in U.S.A.
TABLE OF CONTENTS
SAFETY PRECAUTIONS 3. . . . . . . . . . . . . . . . . . . .
MACHINE SETUP AND OPERATION 4. . . . . . . . .
MAINTENANCE 5. . . . . . . . . . . . . . . . . . . . . . . . . . . .
STORING MACHINE 5. . . . . . . . . . . . . . . . . . . . . . . .
TROUBLE SHOOTING 6. . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS 7. . . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRICAL DIAGRAM 9. . . . . . . . . . . . . . . . . . . .
PARTS LIST 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPTIONS 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OPERATION
Tennant 1220 (11–99) 3
SAFETY PRECAUTIONS
This machine is intended for commercial use. It is
designed to clean carpet and upholstery in an indoor
environment and is not constructed for any other use.
Use only recommended cleaning solutions and
accessory tools.
All operators must read, understand and practice the
following safety precautions.
The following safety alert symbols are used throughout
this manual as indicated in their description:
WARNING: To warn of hazards or unsafe
practices which could result in severe personal
injury or death.
FOR SAFETY: To identify actions which must be
followed for safe operation of equipment.
The following information signals potentially dangerous
conditions to the operator or equipment:
FOR SAFETY:
1. Do not operate machine:
– Unless trained and authorized.
– Unless operator manual is read and
understood.
– In flammable or explosive areas unless
designed for use in those areas.
– With damaged cord or plug.
– If not in proper operating condition.
– In outdoor areas.
– In standing water.
– With the use of additional extension cords.
Only use manufacturer’s extension cord
equipped with machine which has proper
capacity and is grounded.
2. Before operating machine:
– Make sure all safety devices are in place
and operate properly.
3. When using machine:
– Do not run machine over cord.
– Do not pull machine by plug or cord.
– Do not pull cord around sharp edges or
corners.
– Do not unplug by pulling on cord.
– Do not stretch cord.
– Do not handle plug with wet hands.
– Keep cord away from heated surfaces.
– Report machine damage or faulty
operation immediately.
– Follow mixing and handling instructions
on chemical containers.
4. Before leaving or servicing machine:
– Turn off machine.
– Unplug cord from wall outlet.
5. When servicing machine:
– Unplug cord from wall outlet.
– Avoid moving parts. Do not wear loose
jackets, shirts, or sleeves.
– Use manufacturer supplied or approved
replacement parts.
WARNING: Hazardous Voltage. Shock or
electrocution can result. Always unplug machine
before servicing.
WARNING: Flammable materials can cause
an explosion or fire. Do not use flammable
materials in tank(s).
WARNING: Flammable materials or reactive
metals can cause an explosion or fire. Do not pick
up.
GROUNDING INSTRUCTIONS
Machine must be grounded. If it should
malfunction or breakdown, grounding provides a
path of least resistance for electrical current to
reduce the risk of electrical shock. This machine
is equipped with a cord having an
equipment–grounding conductor and grounding
plug. The plug must be plugged into an
appropriate outlet that is properly installed in
accordance with all local codes and ordinances.
Do not remove ground pin; if missing, replace
plug before use.
GROUNDED OUTLET
(3 HOLE)
GROUNDING
PIN

OPERATION
4Tennant 1220 (11–99)
MACHINE SETUP AND OPERATION
FOR SAFETY: Do not operate machine unless
operator manual is read and understood.
1. Fill solution tank with 30.8L (7 gal) of hot water,
60°C (140°F) maximum (Figure 1).
NOTE: Use different buckets to fill and drain machine
to prevent solution system clogs.
FIG. 1
WARNING: Flammable materials can cause
an explosion or fire. Do not use flammable
materials in tank(s).
2. Add a recommended cleaning solution.
FOR SAFETY: When using machine, follow mixing
and handling instructions on chemical containers.
ATTENTION: If using powdered cleaning
chemicals, mix prior to adding.
NOTE: If desired, water alone achieves excellent
cleaning results.
3. Replace dust cover securely after filling.
4. Adjust brush to proper height. Turn height
adjustment knob until bristles slightly touch carpet,
then turn knob another half turn. Turn knob
clockwise to raise and counterclockwise to lower
(Figure 2).
FIG. 2
5. Connect extension cord to machine’s pigtail cord
and attach belt clip to your belt. Plug cord into a
grounded wall outlet (Figure 3) .
GROUNDED OUTLET
(3 HOLE)
GROUNDING
PIN FIG. 3
FOR SAFETY: Do not operate machine with the
use of additional extension cords. Only use
manufacturer’s extension cord equipped with
machine which has proper capacity and is
grounded.
6. Turn on Master switch.
7. Press and hold in Carpet Cleaning button. Pull
machine towards you, 1219 mm (4 ft) at a time.
For best cleaning results, lift machine handle
slightly while pulling backward. This transfers
weight of machine to the pickup head for best
water recovery.
NOTE: Scrubbing stained areas with the brush only
and no spray can prevent overwetting of carpet. Turn
off Master switch and press Carpet Cleaning button.
Be careful not to fray carpet fibers.
8. At end of path, release Carpet Cleaning button,
pull machine towards you another 305 mm (1 ft) to
vacuum excess spray. Push down on handle and
move to next area to be cleaned. Overlap each
path by 50 mm (2 in).
WARNING: Flammable materials or reactive
metals can cause an explosion or fire. Do not pick
up.
NOTE: If brush stops during use, unplug machine and
dislodge any obstructions near the brush. Push reset
button located under switchbox.
9. Recovery tank will fill with dirty water during
cleaning. Watch for foam buildup. If foam does
appear, shut off machine. Remove recovery dome
and pour a recommended defoamer solution into
the recovery tank (Figure 4) .

OPERATION
Tennant 1220 (11–99) 5
FIG. 4
ATTENTION: Do not allow water or foam to enter
vacuum screen. Damage to vacuum will result.
This damage is not covered by warranty.
10. When solution tank is empty, recovery tank must
be emptied. To empty recovery tank, turn off
machine and position a discharge bucket under
drain valve down spout.
NOTE: Do not use same bucket for filling solution
tank.
11. Pull valve T–handle to empty dirty water. Be sure
to close valve before continuing operation.
12. When finished cleaning, use 914 mm(3 ft)
cleanout hose to vacuum remaining water from
solution tank. Attach one end to recovery dome.
Turn on Master switch and use other end to
vacuum water.
UPHOLSTERY CLEANING
1. Disconnect short vacuum hose from recovery
dome and replace with accessory vacuum hose.
2. Connect accessory solution hose to upholstery
connection at back of machine.
3. Turn on Master switch.
4. Begin cleaning by squeezing trigger on accessory
tool to spray cleaning solution.
WARNING: Flammable materials or reactive
metals can cause an explosion or fire. Do not pick
up.
NOTE: Be careful not to overwet upholstery.
NOTE: When cleaning upholstery, always check
cleaning instructions sewn in furniture by
manufacturer.
5. When finished cleaning, turn off machine and
drain recovery tank.
ATTENTION: The solution hose contains
pressurized cleaning solution which can spray
when hose is disconnected. Relieve pressure
before disconnecting hose by squeezing hand
tool trigger for five seconds after turning off
master switch.
6. After relieving pressure in hose, disconnect
solution and vacuum hoses.
MAINTENANCE
To keep machine in good working condition, simply
follow machine’s daily and monthly maintenance
procedures.
WARNING: Hazardous Voltage. Shock or
electrocution can result. Always unplug machine
before servicing.
SERVICING MACHINE:
For ease of servicing, the machine’s tanks are hinged
to pivot away from metal chassis to allow access to
inner components.
ATTENTION: Make sure tanks are empty before
opening.
1. Remove two rear hex–head screws, located under
chassis near wheels.
2. Remove two allen head screws.
3. Remove two remaining hex–head screws located
at front of chassis.
4. Lift tanks upward, away from chassis. The
vacuum tool will pivot upward with tanks.
DAILY MAINTENANCE
1. Thoroughly rinse recovery tank and recovery
dome.
2. Clean vacuum screen, solution tank screens and
brush.

OPERATION
6Tennant 1220 (11–99)
MONTHLY MAINTENANCE
1. Flush pump system with an acetic acid solution to
dissolve normal alkaline chemical buildup.
a. Premix .5L (16 oz) of an acetic acid solution
with 7.5L (2 gal) of hot water 60C (140F )
and pour into solution tank.
FOR SAFETY: When using machine, follow mixing
and handling instructions on chemical containers.
b. Turn on Vacuum/Pump switch.
c. Position brush over floor drain and operate
machine for one minute.
d. Shut off machine and allow remaining solution
to break down alkaline buildup overnight.
e. Next day, spray out remaining solution and
flush system with 11L (3 gal) of clean water.
STORING MACHINE
1. Before storing machine, be certain to flush tanks
and drain machine of all water.
2. Store machine in a dry area in the upright position
with brush raised off floor.
3. Remove recovery dome to promote air circulation.
ATTENTION: Do not expose to rain. Store
indoors.
ATTENTION: If storing machine in freezing
temperatures, be sure that machine, pump and
spraying system are completely drained and dry.

OPERATION
Tennant 1220 (05–99) 7
TROUBLE SHOOTING
PROBLEM CAUSE SOLUTION
Machine does not operate. Faulty switches or wiring. Contact Service Center.
Faulty power cord. Contact Service Center.
Building circuit breaker tripped. Reset breaker.
Solution pump does not operate. Overheated pump. Determine cause and wait 20 minutes
for pump to cool. Reset breaker.
Faulty solution pump. Contact Service Center.
Faulty solenoid. Contact Service Center.
Faulty switch. Contact Service Center.
Loose or broken wiring. Contact Service Center.
Vacuum motor does not operate. Vacuum motor thermal overload
tripped. Check air flow for obstruction, wait 20 minutes for motor to cool.
Vacuum motor circuit breaker tripped. Reset breaker.
Loose or broken wiring. Contact Service Center.
Faulty Master switch. Contact Service Center.
Defective vacuum motor. Contact Service Center.
Worn carbon brushes. Replace brushes or call for service.
Brush motor does not operate. Brush motor circuit breaker tripped. Remove brush obstruction OR
readjust brush height. Reset brush
breaker button at bottom of switch
box.
Carpet Cleaning Switch not pushed. Push Carpet Cleaning Switch.
Faulty brush motor. Contact Service Center.
Loose or broken brush belt. Contact Service Center.
Faulty switch or wiring. Contact Service Center.
Poor pick up. Open drain valve. Close valve.
Clogged standpipe screen in recovery
tank. Remove recovery dome and clean lint off screen.
Air leakage around recovery dome. Tighten recovery dome knobs or
replace gaskets.
Loose vacuum hose connections. Secure connections.
Defective vacuum hose. Replace hose.
Loose vacuum hose cuffs. Secure cuffs to hose.
Pulling machine too fast. Slow down cleaning process.
Uneven or no spray. Dirty or plugged spray tips. Clean or replace tips.
y
Improper spray tip size or spray angle. Replace with proper tips.
Worn spray tips. Replace spray tips.
Solution tank low or empty. Refill solution tank.
Faulty solution pump. Contact Service Center.
Plugged solution tank filter. Clean filter.
Drain valve leaks. Drain valve gaskets worn. Replace gaskets.
Lint or dirt in drain valve. Clean valve.

OPERATION
8Tennant 1220 (07–99)
SPECIFICATIONS
Model 1220
LENGTH 991 mm (39 in)
WIDTH 406 mm (16 in)
HEIGHT 864 mm (34 in)
WEIGHT 39 Kg (86lb)
SOLUTION TANK CAPACITY 31L (7 gal)
RECOVERY TANK CAPACITY 31L (7 gal)
CLEANING PATH WIDTH 406 mm (16 in)
MAXIMUM CLEANING RATE 186 m2(2,000 sq. ft) per hour
BRUSH MOTOR 120V, .1hp,1A, 120W, 1800 rpm
BRUSH SPEED 1200 rpm
SOLUTION PUMP 120V, 6.9bar (100psi), 1A
VACUUM MOTOR 120V, 1.66 hp, 10.3A, 1236W, 3 stage
SEALED WATER LIFT 2972 mm (117 in)
TOTAL POWER CONSUMPTION 120V, 12.7A, 1524W
DECIBEL RATING AT OPERATOR’S EAR,
INDOORS ON CARPET >70dB(A)

ELECTRICAL DIAGRAMS
9
Tennant Roadrunner1220 (07–99)
PUSH BUTTON SWITCH
MASTER
SWITCH
POWER CORD
CONDUIT
SOLENOID
CORD 18/3
(Chassis to
Brush Housing)
SOLUTION
PUMP
AC
+
AC
PUMP
1.5 AMPS
BRUSH
1.5 AMPS
VACUUM
12 AMPS
BRUSH
MOTOR
VACUUM
MOTOR
WHT/ORG
BLK RED
GRN
BLU
ORG WHT
WHT/ORG
WHT/RED WHT/BLK
BLU
RED
BLK
GRN
BLK
BLK
BLK
WHT
BLK
BLK
BLK
WHT
GRN
BLU
WHT
BLK
RED
GRN ORG
GRN WHT
BLK
WHT/RED
WHT/BLK
RED
BLK
WHT/GRN
GRN/YLW
GRN
GRN/YLW
GRN
WHT
BLK
WHT
BLK
120V

PARTS LIST
Tennant 1220 (07–99)
10
TANK GROUP
1
2
3
4
5
6
7
89
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24 25
26
27
28 29
30 31
32
33 34
35
3637
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55

PARTS LIST
Tennant 1220 (07–99) 11
TANK GROUP
REF PART # DESCRIPTION QTY.
1 130304 RECTIFIER 1
2 140879 SCREW, 6–32 X 3/4 1
3140889 SCREW, 1/4–20 X 3/4 4
4607852 SWITCHBOX, TEAL 1
5130441 SWITCH, 120 VOLT 1
6130717 SWITCH, ROCKER 1
7 140549 NUT, LOCK 3/8 CONDUIT 1
8140534 NUT, NYLON 6–32 1
9130166 CORD GRIP 1
10 130237 CORD, 16/3 X 18” YELLOW 1
11 130670 BREAKER, CIRCUIT, 12 AMP 1
12 130760 BREAKER, CIRCUIT, 1.5 AMP 2
13 130977 HARNESS, WIRE 1
14 130242 FITTING, ELBOW 1/2” 1
15 607855 TANK, SOLUTION, TEAL 1
16 130040 WIRE TIE, NYLON 2
17 230500 COVER, DUST 1
18 210242 VALVE, DRAIN W/ METAL HANDLE,
NO SPOUT 1
19 210239 VALVE, DRAIN GATE SEAL
(REQUIRES 2) 2
20 210232 DOWNSPOUT, DRAIN VALVE 1
21 210237 HANDLE, METAL – DRAIN VALVE 1
22 210234 GASKET, DRAIN VALVE 1
23 180612 SCREEN, STANDPIPE 1
24 700144 STANDPIPE ASSEMBLY 1
25 240217 KNOB, RECOVERY DOME 2
26 100112 DOME, RECOVERY 1
27 140037 WASHER, NYLON SPLIT LOCK 2
28 100042 GASKET, RECOVERY DOME 1
29 160421 HOSE, VAC. 1 1/2” X 19–1/8 W/
CUFFS 1
REF PART # DESCRIPTION QTY.
30 230159 O–RING, STANDPIPE 1
31 607857 TANK, RECOVERY, OFF–WHITE 1
32 101714 GASKET, WASTE CHAMBER 1
33 210240 NUT, METAL DRAIN VALVE 1
34 140238 STUD, 1/4–20 X 5 ZINC 4
35 160430 HOSE CUFF, 1–1/2 X 1–1/2 2
36 160423 HOSE, VACUUM 1–1/2 X 36”
(CLEANOUT) 1
37 210240 NUT, METAL DRAIN VALVE 1
38 230503 SHIELD, VACUUM 1
39 100037 GASKET, VACUUM MOTOR 1
40 130416 MOTOR, VACUUM 5.7”, 3 STAGE,
120 VOLT 1
190160 CARBON BRUSH (2/PK) 2
41 230237 BRACKET, SUPPORT 1
42 140501 NUT, LOCK – NYLOCK INSERT 4
43 160838 HOSE, EXHAUST 2” X 24” 1
44 140308 CLAMP, HOSE 2
45 240194 KNOB, HEIGHT ADJUSTMENT 1
46 230382 STUD, HEIGHT ADJUSTMENT 1
47 230638.BK BRACKET, HEIGHT ADJUSTMENT 1
48 140919 SPACER, NYLON 1
49 200450.BK TOOL, FLOOR, 16” BLACK 1
50 200956 SHOE, 16” FLOOR TOOL 2
51 140313 CLAMP, FLOOR TOOL 2
52 140016 WASHER, LOCK 1/4” 4
53 140554 SCREW, HEX CAP 1/4–20 X 3/4 4
54 130250 CORD, EXTENS. 16/3 X 50 FT
YELLOW 1
55 130176 BELT CLIP ONLY, YELLOW 1
DECAL LIST (not shown)
REF PART # DESCRIPTION QTY.
N/S 608136 DECAL, TENNANT LOGO 1
N/S 608158 DECAL, 1220 2
N/S 120399 DECAL, DO NOT ALLOW FOAM 1
N/S 120617 DECAL, HEIGHT ADJUSTMENT 1
N/S 602505 DECAL, INSTRUCTION 1
N/S 120906 DECAL, IMPORTANT – DRAIN 1
N/S 120619 DECAL, WARNING – EXTRACTORS 1

PARTS LIST
Tennant 1220 (07–99)
12
CHASSIS GROUP
1
2
3
4
5
6
10
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
28
32
33
34
34
33
35
36
37 38
39
40
41 42 43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
10
62
10
64
65
7
61
63

PARTS LIST
Tennant 1220 (07–99) 13
CHASSIS GROUP
REF PART # DESCRIPTION QTY.
1 140553 SCREW, HEX CAP 1/4–20 X 1/2 2
2140052 WASHER, EXT LOCK TOOTH 8
3140891 SCREW, 10–24 X 5/8 1
4140031 WASHER, EXT LOCK TOOTH 1
5140898 SCREW, 3/8–16 X 3/4 2
6140914 SPACER, NYLON .375IDX.5X.25 2
7180131 GROMMET, RUBBER 2
8 140553 SCREW, HEX CAP 1/4–20 X 1/2 2
9140052 WASHER, EXT LOCK TOOTH 2
10 230301.BK CHASSIS, HINGED, BLACK 1
11 140801 SCREW, 8–32 X 3/8 2
12 140023 WASHER, INT LOCK TOOTH 1
13 140553 SCREW, HEX CAP 1/4–20 X 1/2 2
14 140016 WASHER, LOCK 1/4” 2
15 140804 SCREW, 10–24 X 1 2
16 140519 NUT, KEP 10–24 2
17 140200 SCREW, HEX CAP 3/8–16 X 1/2 1
18 150616 ADAPTER, BRASS 1/8 X 1/4, 37
TUBE 1
19 150526 HOSE BARB, BRASS 1/8 NPT X 1/4 1
20 140325 CLAMP, EAR 1/4 1
21 607307 HOSE, 1/4” X 12” 1
160510 HOSE GUARD 1/4” X 10” 1
22 140325 CLAMP, EAR 1/4 1
23 150515 HOSE BARB, 1/4 MPT X 1/4 H 1
24 150406 ELBOW, 90, 1/4 FPT X 1/4 MPT 1
25 180628 SCREEN, SOLUTION TANK 2
26 150403 ELBOW, 452
27 150415 ELBOW, 90NYL 1/4 MPT X 3/8 2
28 140301 CLAMP, PINCH 5
29 607412 HOSE, 3/8” X 2” 1
30 160310 TEE, 3/8 HOSE BARB, NYLON 1
31 607415 HOSE, 3/8” X 4” 1
32 606163 HOSE, 3/8” X 22” 1
33 140310 CLAMP, HOSE 2
34 150412 ELBOW, 90NYL 3/8 MPT X 3/8 2
REF PART # DESCRIPTION QTY.
35 180103 PUMP, SHURFLO 100 PSI, 120
VOLT 1
36 230508 SHIELD, PUMP 1
37 160570 HOSE, 3/8” X 11” 1
160570 HOSE GUARD 3/8” X 11” 1
38 140519 NUT, KEP 10–24 2
39 140012 WASHER, FLAT 3/16” 2
40 140301 CLAMP, PINCH 6
41 150516 HOSE BARB, BRASS 1/4 MPT X 3/8 2
42 150709 TEE, STR 1/4FPTX1/4FPTX1/4MPT 1
43 210033 VALVE, SOLENOID, 120 VOLT, 60HZ 1
44 230509 SHIELD, SOLENOID 1
45 150406 ELBOW, STR–901/4FPTX1/4MPT 1
46 150517 HOSE BARB, BRASS, 1/4MPTX1/2 2
47 140310 CLAMP, HOSE 2
48 606162 HOSE, 1/2” X 26” 1
160209 HOSE GUARD, 1/2” X 25” 1
49 150517 HOSE BARB, BRASS, 1/4MPTX1/2 2
50 150401 ELBOW, 90, 1/4FPTX1/4FPT 1
51 130977 HARNESS, WIRING 1
52 150615 NIPPLE, BRASS 1/4” CLOSE 1
53 140033 WASHER, FLAT 1/2” USS–BLUE 2
54 150933 PLUG, QCK CPLR SER. 60 FPT 1
55 130104 BUSHING, SNAP .875 ID – BLACK 1
56 230294 AXLE, HINGED 1
57 140705 RIVET, POP 2
58 140008 WASHER, FLAT 2
59 103025 WHEEL, 10” X 1.75 GRAY 2
60 103019 CAP, HUB 2
61 140010 WASHER, FLAT 1/4” SAE 2
62 140701 RIVET, POP 6
63 140554 SCREW, HEX 1/4–20 X 3/4 2
64 140016 WASHER, LOCK 1/4” 2
65 140554 SCREW, HEX 1/4–20 X 3/4 2

PARTS LIST
Tennant 1220 (07–99)
14
BRUSH GROUP
1
2
3
4
5
6
7
8
910
11
12
13 14
15
16
17 18 19
20
21
22
26
24
25
23 34
28
29
30 3132
33
27

PARTS LIST
Tennant 1220 (07–99) 15
BRUSH GROUP
REF PART # DESCRIPTION QTY.
1 700212 BRUSH ASM, 16” COMPLETE 1
2140887 SCREW, 10–24 X 3/8 10
3 100734.BK PLATE, BRUSH, 16” 1
4100006 GASKET, BASE PLATE 1
5230507 BELT, BRUSH DRIVE 1
6 140548 NUT, FINJAM 5/16 1
7230505 PULLEY, BRUSH W/ SCREW 1
8230363 SPACER, BRUSH, .625OD X .328ID
X .125 1
9100005 GASKET, BEARING BLOCK 1
10 230261 BLOCK, BEARING 2
11 140125 BEARING, BRUSH 2
12 100049 SEAL, BRUSH BEARING 2
13 230257 SHAFT, BRUSH, (16”) 1
14 240004 BRUSH, CYLINDER, (16”) 1
15 140554 SCREW, HEX CAP 1/4–20 X 3/4 4
16 230506 PULLEY, MOTOR W/ SCREW 1
17 140518 NUT, KEP 10–32 2
18 230366 PLATE, MOTOR MOUNT 1
REF PART # DESCRIPTION QTY.
19 130471 MOTOR, BRUSH DRIVE 120 VOLT 1
20 140233 SCREW, HEX CAP 3/8–16 X 1–3/4 1
21 140036 WASHER, FLAT 3/8 2
22 140564 BOLT, SHOULDER 3/8 X 3/4 2
∇23 700860 SPRAYBAR 16” COMPL. 1
24 230267 SPRAYBAR MANIFOLD, 16” 1
25 150208 PLUG, BRASS HEX HEAD 1/8 3
26 201001 NOZZLE, 1/8” BRASS, NO SCREEN 4
27 150616 FITTING, 1/8 NPT X 1/4 1
28 230264.BK CLAMP, SPRAYBAR MANIFOLD 1
29 130671 CORD, ASM, 18/3X24”, BLACK W/
CORD GRIPS 1
30 140036 WASHER, FLAT 2
31 140515 NUT, LOCK NYL INSERT 3/8–16 1
32 140407 SPRING, .845 OD 1
33 140515 NUT, LOCK NYL INSERT 3/8–16 1
34 607864 HOUSING, BRUSH 16” TEAL 1
∇ASSEMBLY
INCLUDED IN ASSEMBLY
SOLUTION PUMP BREAKDOWN
4
6
1
2
5
3
REF PART # DESCRIPTION QTY.
1 190129 PRESSURE SWITCH 1
2 190128 UPPER PUMP HOUSING KIT 1
3190131 SERVICE KIT 1
REF PART # DESCRIPTION QTY.
4 190130 LOWER PUMP HOUSING KIT 1
5190171 KIT, PUMP VALVE (VITON) 1
6180103 SOLUTION PUMP 100 PSI (COMP.) 1

OPTIONS
16 Tennant 1220 (06–99)
127mm (5 in) HAND TOOL
10
211 12 13
9
8
5
4
36
1
7
REF PART # DESCRIPTION QTY.
200505 TOOL, HAND (COMPLETE) 1
1200431.BK TOOL, HAND 1
2150913 COUPLER, QUICK 1
3150615 NIPPLE, CLOSE 1
4200905 TRIGGER, HAND TOOL 1
5210210 VALVE, FLOW CONTROL 1
6190600 PIN & SPRING, VALVE 1
REF PART # DESCRIPTION QTY.
7 N/A CAP, VALVE 1
8 150606 NIPPLE, HEX 1/4 1
9150403 ELBOW, ST 1/4 45°1
10 200992 BODY, SPRAY 1/4F 1
11 200996 SCREEN, SPRAY NOZZLE 1
12 200965 TIP, SPRAY #8002 1
13 200994 CAP, SPRAY BODY 1
CREVICE TOOL
1
5
67
23
4
REF PART # DESCRIPTION QTY.
200517 TOOL, CREVICE (COMPLETE) 1
1200436.BK TOOL 1
2 200975 NOZZLE 1
3 210014 VALVE, TOGGLE 1
4210020 CAP, VALVE POSITIONER 1
REF PART # DESCRIPTION QTY.
5 160106 HOSE, ASM. 1
6150100 FITTING, 1/4MX1/8F 1
7150913 COUPLER 1

OPTIONS
17
Tennant 1220 (06–99)
UPHOLSTERY TOOL
1
3
2
548
6
7
10
13
12
9
14
11
REF PART # DESCRIPTION QTY.
200540 TOOL, UPHOL. (COMPLETE) 1
1200845 COVER 1
2 200843 GASKET 1
3 190631 KIT, VALVE ASM. 1
4210226 VALVE, LP 1
5200991 NOZZLE 1
6 200838 SCREW 4
7 200840 TRIGGER 1
REF PART # DESCRIPTION QTY.
8 200844 HOSE, VACUUM 1
9200837 HOSE, SOLUTION 1
10 200848 FITTING 1
11 200842 FILTER 1
12 200841 SCREEN, FILTER 1
13 150606 FITTING, 1/4MX1/4M 1
14 150913 COUPLER 1
SOLUTION AND VACUUM HOSES
1
2
4
4
3
5
6
7
REF PART # DESCRIPTION QTY.
∇1 160185 HOSE, SOLUTION 15’ 1
2150913 COUPLER, QUICK 1
3150933 PLUG, QUICK COUPLER 1
4150615 NIPPLE 2
REF PART # DESCRIPTION QTY.
∇5 160400 HOSE, VACUUM 15’ 1
6160430 CUFF, HOSE 1–1/2” 2
7160451 CONNECTOR, VAC HOSE 1
∇ASSEMBLY
INCLUDED IN ASSEMBLY

OPTIONS
18 Tennant 1220 (06–99)
330mm (13 in) FLOOR TOOL
3
1
2
5
46
7
8
10
11
9
12 13 14
15
16
17
20
21
22
19
23
24
25
18
REF PART # DESCRIPTION QTY.
600048 FLOOR TOOL (COMPLETE) 1
1200403.BK TOOL, FLOOR 1
2200939 SHOES, S/S 2
∇3200927 ASM., GRIP, ADJ. 1
4200912 FOAM, GRIP 1
5140259 SCREW, 1/4X3/4 2
6200902 TRIGGER 1
7 200809 SLEEVE, TRIGGER 1
8140605 PIN 1
8 140520 NUT, PUSH (NOT SHOWN) 2
9210150 VALVE, FLOW CONTROL 1
10 190603 KIT, VALVE PIN & SPRING 1
11 N/A CAP, HEX, VALVE 1
12 150403 ELBOW, 1/4–45°1
13 150615 NIPPLE, CLOSE 1/4 1
REF PART # DESCRIPTION QTY.
14 150913 COUPLER, QUICK 1
15 160170 HOSE, SOLUTION, LP 1
16 150606 NIPPLE, HEX 1/4” 1
17 140058 WASHER 1
∇18 700062 ASM., SPRAY BAR 1
19 150700 CROSS, FITTING 1
20 150600 NIPPLE 2
21 150401 ELBOW, 901/4FX1/4F 2
22 200993 SPRAY BODY 3
23 200996 SCREEN, SPRAY BODY 3
24 200964 TIP 3
25 200994 CAP, SPRAY BODY 3
∇ASSEMBLY
INCLUDED IN ASSEMBLY