Tennsco Z-Line Record Archive Shelving Instruction Manual

PK-1990719
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
Z-Line Record Archive Shelving
RETAIN INSTRUCTIONS FOR FUTURE REFERENCERETAIN INSTRUCTIONS FOR FUTURE REFERENCE
Tennsco LLC., Dickson, TN 37056-1888 • [phone]
GENERAL SAFETY INFORMATIONGENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance on units.
LIMITED WARRANTYLIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in
the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.

ASSEMBLY OF ARCHIVE SHELVING
Tools Needed: A rubber mallet for seating the shelf supports into the uprights.
Two people are recommended for assembly. Approximate assembly time: 20-30 minutes per section.
4. Repeat the instructions in step 3 to construct a second set
of unit ends.
2. Depending upon whether you ordered a single unit or an
adder unit, you may have one or both of the styles of upright
shown. A single unit will use EUR posts for all four uprights,
as show below in Figure A. If you plan on installing an adder
unit, you should build your starter unit with two ZTP posts
on one end which will join with the adder as shown in Figure B.
1. The reference numbers used throughout this sheet refer to
the illustration on the back cover. This is to help you to
identify the various parts as they are mentioned.
3. With the help from an associate, or using a wall for support,
connect two EUR uprights (Ref. No. 1) using two front-to-
back supports (Ref. No. 3), one at the top and one near the
bottom (leaving the bottom-most keyhole slot empty). Be
sure the front-to-back supports are fully seated in the
keyhole slots as shown.
5. With the help of an associate, connect the two unit ends
with left-to-right shelf supports (Ref. No. 4). Again, be sure
that the at surface of the shelf support is facing up, and
that the shelf supports are fully seated, as was illustrated in
step 3.
EUR
Inset is shown from
opposite side.
NOTE: The uprights must be positioned so that the
narrow part of the slots is toward the floor, as shown.
ZTP
Figure A
Figure B
IMPORTANT: Support MUST
be inserted so the at
surface is on top as shown
in prole at left.
NOTE: If you are planning to install an adder unit,
this second set of uprights should consist of ZTP
uprights (Ref. No. 2) so that adjacent sections can
be tied together. Carefully review step 2 and step 9
to better understand.





9. If joining more than one unit together, your original unit
should have been assembled with ZTP uprights on one end,
as described in step 4. Simply continue adding shelf supports
and uprights to complete your additional units.
8. If particle board decking (Ref. No. 6) was ordered, place the
decking on each shelving level. The decking should t ush
inside the shelf supports. If you have purchased a single unit,
your shelving unit is now complete. For adder units, see step 9.
7. Shelf deck supports (Ref. No. 5) are necessary for 30”deep units
only. Attach shelf deck supports by inserting the metal prongs
on the deck support into the slots on the shelf supports. 69” x
30” units require two shelf deck supports per level (as shown);
42” x 30” units require only one shelf deck support per level,
place in the center.

6. Attach the remaining shelf supports at the desired shelf
levels, making sure that all shelf supports are completely
seated in the upright slots.
Holes
55 & 56
NOTE: For archive storage boxes to fit stacked two
high per level, there should be a minimum of 16 holes
between shelf supports. We recommend placing the
bottom shelf support rivet in the 2nd, 19th, 37th, and
55th holes on 84” high units (as shown) and in the 2nd,
20th, and 39th holes on 60” units.
Holes
37 & 38
Holes
19 & 20
Holes
2 & 3




REPLACEMENT PARTSREPLACEMENT PARTS
DESCRIPTIONDESCRIPTION
QTY.QTY.
REF.REF.
NO.NO.
Left-to-RightLeft-to-Right
Shelf SupportShelf Support
(Ref No. 4)(Ref No. 4)

NOTE: Additional hardware may be included for replacement purposes.NOTE: Additional hardware may be included for replacement purposes.
Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.
However, should your unit contain missing or damaged parts, please contact your purchase location.However, should your unit contain missing or damaged parts, please contact your purchase location.
49B19949B199
PART NO.PART NO.
Angle Post (single or starter units only)
OR
“T” Post (adder units only)
OR
Front-to-Back End Support
OR
Left-to-Right Shelf Support
OR
Shelf Deck Support
Optional Particleboard Decking
OR
OR
OR
4
2
6
6
3
EUR-60
EUR-84
ZTP-60
ZTP-84
VDRS-1516
VDRS-3016
VDRS-4216
VDRS-6914
FBSV-30
PB-4215
PB-4230
PB-6915
PB-6930
1
2
3
4
5
6
42w42w
x 15dx 15d
42w42w
x 30dx 30d
69w69w
x 15dx 15d
69w x69w x
30d30d
42w42w
x 15dx 15d
42w42w
x 30dx 30d
69w69w
x 15dx 15d
69w69w
x 30dx 30d
QTY.QTY.
60” HIGH60” HIGH 84” HIGH84” HIGH
4
2
6
6
3
3
4
2
6
6
3
4
2
6
6
6
3
4
2
8
8
4
4
2
8
8
4
4
4
2
8
8
4
4
2
8
8
8
4




ZTPZTP
UprightUpright
(Ref No. 2)(Ref No. 2)
Front-to-BackFront-to-Back
End SupportEnd Support
(Ref No. 3)(Ref No. 3)
Particleboard DeckingParticleboard Decking
(Ref No. 6)(Ref No. 6)
EUR UprightEUR Upright
(Ref No. 1)(Ref No. 1)
Shelf Deck SupportShelf Deck Support
(Ref No. 5)(Ref No. 5)