Tennsco ZST-6060S Instruction Manual

REPLACEMENT PARTSREPLACEMENT PARTS
Tennsco Corp. , Dickson, TN 37056-1888 • [phone]
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
Z-Line Tire Rack - Starter
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE!RETAIN INSTRUCTIONS FOR FUTURE REFERENCE!
GENERAL SAFETY INFORMATIONGENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance on shelving.
LIMITED WARRANTYLIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in
the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during ship-
ment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
PK-2880216PK-2880216
TO OBTAIN PROPER REPLACEMENT PARTS, PLEASE PROVIDE THE FOLLOWING INFORMATION:TO OBTAIN PROPER REPLACEMENT PARTS, PLEASE PROVIDE THE FOLLOWING INFORMATION:
Purchase Date Contact person’s name
Description of part(s) needed and part Your company name
number(s) as shown in Parts List (above) Who the product was purchased from
Color (i.e. Medium Grey, etc.) Was item missing, or was it damaged?
If requesting parts by telephone, please have as much of the above information ready as possible.f requesting parts by telephone, please have as much of the above information ready as possible.
This information may also be submitted online at www.tennsco.com/replacement.cfmThis information may also be submitted online at www.tennsco.com/replacement.cfm
Tennsco Corp., P. O. Box 1888, Dickson, TN 37056-1888 Customer Service: [phone] Fax: [phone]Tennsco Corp., P. O. Box 1888, Dickson, TN 37056-1888 Customer Service: [phone] Fax: [phone]
Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.
However, should your unit contain missing or damaged parts, replacements may be obtained directly from Tennsco.However, should your unit contain missing or damaged parts, replacements may be obtained directly from Tennsco.
To obtain proper replacement parts, follow the instructions below: (or ll out the form at www.tennsco.com/replacement.cfm)To obtain proper replacement parts, follow the instructions below: (or ll out the form at www.tennsco.com/replacement.cfm)
REF. NO. DESCRIPTION PART NO. QTY.REF. NO. DESCRIPTION PART NO. QTY.
SINGLE ENTRY UNITS
ZST-6060S
1 Upright Post EUR-60 4
2 Shelf Support (60”W) LRA-60 4
3 Shelf Support (12”W) LRA-12 6
4 Wall Tie WT-9 2
ZST-6084S
1 Upright Post EUR-84 4
2 Shelf Support (60”W) LRA-60 6
3 Shelf Support (12”W) LRA-12 6
4 Wall Tie WT-9 2
ZST-60120S
1 Upright Post EUR-120 4
2 Shelf Support (60”W) LRA-60 8
3 Shelf Support (12”W) LRA-12 8
4 Wall Tie WT-9 6
ZST-60144S
1 Upright Post EUR-144 4
2 Shelf Support (60”W) LRA-60 10
3 Shelf Support (12”W) LRA-12 10
4 Wall Tie WT-9 6
DOUBLE ENTRY UNITS
ZDT-6060S
1 Upright Post EUR-60 8
2 Shelf Support (60”W) LRA-60 8
3 Shelf Support (12”W) LRA-12 12
4 Cross Aisle Tie CAT-18 4
ZDT-6084S
1 Upright Post EUR-84 8
2 Shelf Support (60”W) LRA-60 12
3 Shelf Support (12”W) LRA-12 12
4 Cross Aisle Tie CAT-18 4
ZDT-60120S
1 Upright Post EUR-120 8
2 Shelf Support (60”W) LRA-60 16
3 Shelf Support (12”W) LRA-12 16
4 Cross Aisle Tie CAT-18 4
ZDT-60144S
1 Upright Post EUR-144 8
2 Shelf Support (60”W) LRA-60 20
3 Shelf Support (12”W) LRA-12 20
4 Cross Aisle Tie CAT-18 4
Congratulations on your purchase of a Z-Line Tire Rack from
Tennsco! Z-Line’s interlocking keyhole design not only makes
installation fast and easy, but eliminates the need for clips,
gussets, sway braces or other hardware commonly used in
conventional shelving.
Tennsco uses sturdy steel construction for strength and
durability. Our attractive and durable powder-coated
paint nish will provide years of service.
NOTE: Units are designed to store tires ONLY!
Not designed for tires on mounted wheels.

ASSEMBLY OF TIRE RACK - STARTER
Two people are recommended for assembly. Approximate assembly time: 15-25 minutes.
2. Laying at on the ground, connect two EUR upright (Ref.
No. 1) posts together with two front-to-back supports
(Ref. No. 2), one at the top and one near the bottom,
leaving the bottom keyhole slot empty. Be sure the
supports are fully seated in the slots.
3. Place the remaining front-to-back support(s) evenly
along the uprights. This forms one end of the tire rack.
4. Repeat steps 2 and 3 to construct a second set of
unit ends.
1. The reference numbers used throughout this sheet refer
to the illustration on the back cover. This is to help you
to identify the various parts as they are mentioned.
5. With the help of an associate, raise the two unit ends
up and connect them with left to right channel beams
(Ref. No. 3). Be sure the channel beams are fully seated.
6. Attach the next section of left-to-right channel supports
and place the shelf reinforcement in the middle the
next shelf level.
8. Place the nal left-to-right channel supports near the
top of the unit. Attach the shelf support in the center.
9a. Attach the wall tie to the top of the unit on the left
and right posts at the back of the unit. Taller units
require additional wall ties (included), for support.
These should be placed about a foot lower than the
wall ties above them.
NOTE: Wall Ties are REQUIRED to be used
for unit stability on Single Entry Units.
NOTE: Cross Aisle Ties are REQUIRED to be
used for unit stability on Double Entry Units.
9b. Assemble your second unit by following the same steps
listed. Attach the cross aisle ties to the top and bottom
of the left and right posts.
10. Your Z-Line Tire Rack assembly is now complete!
11. If an adder unit has been purchased, see the Z-Line Tire
Rack - Adder instructions.
For Single Entry Units
For Double Entry Units

ASSEMBLY OF TIRE RACK - STARTER
Two people are recommended for assembly. Approximate assembly time: 15-25 minutes.
2. Laying at on the ground, connect two EUR upright (Ref.
No. 1) posts together with two front-to-back supports
(Ref. No. 2), one at the top and one near the bottom,
leaving the bottom keyhole slot empty. Be sure the
supports are fully seated in the slots.
3. Place the remaining front-to-back support(s) evenly
along the uprights. This forms one end of the tire rack.
4. Repeat steps 2 and 3 to construct a second set of
unit ends.
1. The reference numbers used throughout this sheet refer
to the illustration on the back cover. This is to help you
to identify the various parts as they are mentioned.
5. With the help of an associate, raise the two unit ends
up and connect them with left to right channel beams
(Ref. No. 3). Be sure the channel beams are fully seated.
6. Attach the next section of left-to-right channel supports
and place the shelf reinforcement in the middle the
next shelf level.
8. Place the nal left-to-right channel supports near the
top of the unit. Attach the shelf support in the center.
9a. Attach the wall tie to the top of the unit on the left
and right posts at the back of the unit. Taller units
require additional wall ties (included), for support.
These should be placed about a foot lower than the
wall ties above them.
NOTE: Wall Ties are REQUIRED to be used
for unit stability on Single Entry Units.
NOTE: Cross Aisle Ties are REQUIRED to be
used for unit stability on Double Entry Units.
9b. Assemble your second unit by following the same steps
listed. Attach the cross aisle ties to the top and bottom
of the left and right posts.
10. Your Z-Line Tire Rack assembly is now complete!
11. If an adder unit has been purchased, see the Z-Line Tire
Rack - Adder instructions.
For Single Entry Units
For Double Entry Units

REPLACEMENT PARTS
REPLACEMENT PARTS
Tennsco Corp. , Dickson, TN 37056-1888 • [phone]
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
Z-Line Tire Rack - Starter
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE!
GENERAL SAFETY INFORMATION
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance on shelving.
LIMITED WARRANTY
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in
the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during ship-
ment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
PK-2880216
PK-2880216
REF. NO. DESCRIPTION PART NO. QTY.
REF. NO. DESCRIPTION PART NO. QTY.
SINGLE ENTRY UNITS
ZST-6060S
1 Upright Post EUR-60 4
2 Shelf Support (60”W) LRA-60 4
3 Shelf Support (12”W) LRA-12 6
4 Wall Tie WT-9 2
ZST-6084S
1 Upright Post EUR-84 4
2 Shelf Support (60”W) LRA-60 6
3 Shelf Support (12”W) LRA-12 6
4 Wall Tie WT-9 2
ZST-60120S
1 Upright Post EUR-120 4
2 Shelf Support (60”W) LRA-60 8
3 Shelf Support (12”W) LRA-12 8
4 Wall Tie WT-9 6
ZST-60144S
1 Upright Post EUR-144 4
2 Shelf Support (60”W) LRA-60 10
3 Shelf Support (12”W) LRA-12 10
4 Wall Tie WT-9 6
DOUBLE ENTRY UNITS
ZDT-6060S
1 Upright Post EUR-60 8
2 Shelf Support (60”W) LRA-60 8
3 Shelf Support (12”W) LRA-12 12
4 Cross Aisle Tie CAT-18 4
ZDT-6084S
1 Upright Post EUR-84 8
2 Shelf Support (60”W) LRA-60 12
3 Shelf Support (12”W) LRA-12 12
4 Cross Aisle Tie CAT-18 4
ZDT-60120S
1 Upright Post EUR-120 8
2 Shelf Support (60”W) LRA-60 16
3 Shelf Support (12”W) LRA-12 16
4 Cross Aisle Tie CAT-18 4
ZDT-60144S
1 Upright Post EUR-144 8
2 Shelf Support (60”W) LRA-60 20
3 Shelf Support (12”W) LRA-12 20
4 Cross Aisle Tie CAT-18 4
Congratulations on your purchase of a Z-Line Tire Rack from
Tennsco! Z-Line’s interlocking keyhole design not only makes
installation fast and easy, but eliminates the need for clips,
gussets, sway braces or other hardware commonly used in
conventional shelving.
Tennsco uses sturdy steel construction for strength and
durability. Our attractive and durable powder-coated
paint nish will provide years of service.
NOTE: Units are designed to store tires ONLY!
Not designed for tires on mounted wheels.
Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.
However, should your unit contain missing or damaged parts, please contact your purchase location.
49B288