Tennsco Z Series Instruction Manual

REPLACEMENT PARTS
PK-2000919
DESCRIPTION
QTY.
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
REF.
NO.
Left-to-Right
Shelf Support
(Ref No. 4)

Tennsco LLC., Dickson, TN 37056-1888 • [phone]
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance on carts.
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in
the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
NOTE: Additional hardware may be included for replacement purposes.
Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.
However, should your unit contain missing or damaged parts, please contact your purchase location.
49B200
PART NO.
Angle Post (single or starter units only)
OR
“T” Post (adder units only)
OR
Front-to-Back End Support
OR
Left-to-Right Shelf Deck Support
OR
Shelf Deck Support
OR
Optional Particleboard Decking
OR
OR
OR
Optional Wiring Decking
OR
OR
OR
4
2
6
6
3
3
EUR-60
EUR-84
ZTP-60
ZTP-84
LRA-15
LRA-30
LRA-42G
LRA-69
SDS-15
SDS-30
PB-4215
PB-4230
PB-6915
PB-6930
ZWD-4215
ZWD-4230
ZWD-6915
ZWD-6930
1
2
3
4
5
6
7
42w
x 15d
42w
x 30d
69w
x 15d
69w x
30d
42w
x 15d
42w
x 30d
69w
x 15d
69w
x 30d
QTY.
60” HIGH 84” HIGH
4
2
6
6
3
3
4
2
6
6
3
3
3
4
2
6
6
3
3
3
4
2
8
8
4
4
4
2
8
8
4
4
4
4
2
8
8
4
4
4
4
4
2
8
8
4
4
4




ZTP
Upright
(Ref No. 2)
Front-to-Back
End Support
(Ref No. 3)
Particleboard Decking
(Ref No. 6)
EUR Upright
(Ref No. 1)
Front-to-Back Shelf
Deck Support
(Ref No. 5)
Wire Decking
(Ref No. 7)
Z-Line Record Archive Storage Racks
ZA421560-3D, ZA421584-4D, ZA423060-3D, ZA423084-4D,
ZA691560-3D, ZA691584-4D, ZA693060-3D, ZA693084-4D



ASSEMBLY OF RECORD ARCHIVE SHELVING
Tools Needed: A rubber mallet for seating the shelf supports into the uprights.
Two people are recommended for assembly. Approximate assembly time: 20-30 minutes per section.
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
9. If joining more than one unit together, your original unit
should have been assembled with ZTP uprights on one end,
as described in step 4. Simply continue adding shelf supports
and uprights to complete your additional units.
4. Place a third front-to-back support in the middle slots of
the two uprights (at the level you want your third shelf to
be). This forms one end of the shelving unit. Repeat steps 3
and 4 to construct a
second set of
unit ends.
2. Depending upon whether you ordered a single unit or an
adder unit, you may have one or both of the styles of upright
shown. A single unit will use EUR posts for all four uprights,
as show below in Figure A. If you plan on installing an adder
unit, you should build your starter unit with two ZTP posts
on one end which will join with the adder as shown in Figure B.
1. The reference numbers used throughout this sheet refer to
the illustration on the back cover. This is to help you to
identify the various parts as they are mentioned.
3. With the help from an associate, or using a wall for support,
connect two EUR uprights (Ref. No. 1) using two front-to-
back supports (Ref. No. 3), one at the top and one near the
bottom (leaving the bottom-most keyhole slot empty). Be
sure the front-to-back supports are fully seated in the
keyhole slots as shown.
5. With the help of an associate, connect the two unit ends
with left-to-right shelf supports (Ref. No. 4). These should
be placed with the ange up and at matching levels
with the front-to-back supports, creating a at surface
on which to
place decking.
8. If particle board decking (Ref. No. 6) was ordered, place the
decking on each shelving level. The decking should t ush
inside the shelf supports. If you have purchased a single unit,
your shelving unit is now complete. For adder units, see step 9.
7. Attach the shelf reinforcements (Ref. No. 5) at each level by
sliding them onto the rivets until centered. Tap down on the
reinforcements until they are seated rmly.

6. Attach the remaining shelf supports at the desired shelf
levels, making sure that all shelf supports are completely
seated in the upright slots.
EUR
NOTE: Inset is shown from the opposite side (below).
ZTP
Figure A
Figure B
IMPORTANT: All shelf supports
must be installed with the ange
facing up, as shown on right. This
ange is what the shelves will
rest on.
NOTE: If you are planning to install an adder unit, this
second set of uprights should consist of ZTP uprights
(Ref. No. 2) to act as an intermediate assembly.
Carefully review step 2 to better understand.


NOTE: If you have purchased additional shelf levels, the
shelf supports for the extra levels may also be inserted
at this time.

NOTE:
Every fourth
keyhole slot
is shaped
differently
(with a
attened top)
for easier
alignment of
supports.
Supports are properly
seated when alignment
hole is fully visable.

Narrow area
of keyhole
slot is at the
bottom.
NOTE: Recommended
number of reinforements
per shelf are as follows:
48”w-69”w = 1 reinforcement
72”w = 2 reinforcement
84”w-96”w = 3 reinforcements