TeraBee Air Quality SB5 User manual

1
Terabee Air Quality SB5
Quick Start Guide
QR code containing the
device connection URL
You may log below the
device’s physical location
(building, floor, room):
For complete device instructions,
please scan this QR code to
access the User Manual
Please keep this guide or take and store
a photo of this page in your archives
V1.0

2
1. Power your device
Connect the Terabee device to the power adapter provided in the
package.
Once powered, the device is ready for conguration within 10 seconds
The ashing blue LED indicates that the device has switched to the
conguration mode and activates a Wireless Access Point with the
following name and format: AQ-SB5_xx:xx:xx:xx:yy:yy
Flashing blue LED

3
2. Connect to the WiFi Access Point
From a smartphone or a computer, check for the SSID of the
Air Quality SB5 device (format SB5_MAC address) among the listed
WiFi networks, and connect to this WiFi Access Point using the
following credentials:
Based on the above picture, the WiFi SSID is:
AQ-SB5_94:E6:86:C3:95:08 and the WiFi Password is: SB5_9508
Example of connection:
SSID: AQ-SB5_xx:xx:xx:xx:yy:yy (where x and y represent any
hexadecimal digit)
Password: SB5_yyyy (where yyyy are the last four hexadecimal
digits of the above SSID)

4
3. Configure your WiFi communication
Once connected to the Air Quality SB5 WiFi Access Point, either:
The graphic of the message can be dierent, depending on the Web
browser
An OS security message may appear due to an error caused by
a certicate missing for a local address. You should not worry, as
this is standard system behavior for local connections and not a
security concern
Ignore the warning and click the Advanced button
type in the URL: https://192.168.4.1 in a Web browser
or scan the QR code on the front page of this guide, and open
the URL in a Web browser

5
Finally, a popup asks for access authorization
Then click on the link “Proceed to [device URL address]”
The default administrator username is admin, and the default
administrator password is admin. You will be asked later on to
change this password

6
Disconnect your smartphone or computer from the device’s WiFi
Access Point and reconnect to the WiFi Local Network
You are all set!
WiFi Connection Enter the WiFi local network SSID and password
WiFi restriction: Only a 2.4 GHz WiFi network can be used
Administration Type in an administrator password to secure
the device’s conguration access
While you may keep the default “admin” password, you are
advised to change this password for security reasons
You then enter a conguration window displaying “WiFi connection”
and “Administration” sections:
1
2

7
4. Device configuration
4.1. Web GUI home page
As soon as the WiFi connection is set, the device goes into a 10-minute
warm-up period. During this time, the LED will notify this status with a
steady white color.
Now connect to the WiFi Local Network with your smartphone or
computer, and either:
You now have access to the device Web GUI home page where you can:
You may get the same security messages described earlier when
accessing the device’s WiFi Access Point
You can ignore them, click on the “Advanced” button, then on the
“Proceed to [device URL address]” link
If the device’s LED starts to blink red alternatively with the steady
white color, it means the connection to the WiFi network failed.
The device network needs to be set up through conguration mode
accessible via a short press on the reset button
type in a Web browser the IP address assigned automatically to
the Air Quality SB5 device by the WiFi local network
or scan the QR code on the front page of this guide, and
access the URL as described in section 3
visualize the air quality dashboard
access the device conguration menu with the administrator
password

8
The Air Quality Index rates indoor air quality with a background
color reecting the LED notication
Click the “Refresh” button for a manual refresh of the air
quality metrics. Ticking the box “Enable auto-refresh” enters an
automatic update every 30 seconds
1
2

9
The eight widgets reect the dierent air quality metrics.
Please refer to the User Manual for a detailed description of
each metric
Click the “Conguration” button to access the password-
protected device conguration page
Indication of the Device ID and rmware version
3
4
5
4.2. Configuration menu
Click the “Conguration” button to access the authentication window.
Type in the administrator username “admin” and password chosen in
section 3.
Once signed in, you access the conguration window of the sensor

10