TEREN H17P User manual

H17P Flush Mount T/RH Display Unit/Transmitter -Operation Manual Edition:A/1
1
Flush Mount T/RH Display Unit/Transmitter
Applications & Features
Apply for flush mount, measure and display environment
T/RH such as cleanrooms in electronics or pharmaceutical
plants, hospital and various laboratories, etc.
316L front panel, PMMA window, flat surface, no dust stays,
good for all detergents, sanitizers and bactericides
With monochrome LCD display, specially designed for a
variety of imported well-known brands (E+E and Rotronic)
probe products
High accuracy, 100% field interchangeable without
re-calibration
2 channels 4~20mA output, with over voltage and reverse
polarity protection
Strong EMI capability, meet the requirements of EN61326-1
industrial equipment
Compatible to any DDC/PLC/SCADA or other data collect
and control systems
Specifications
T/RH remote probe: (Refer to the operation manual from the original
manufacturers for details)
Main unit and display：4 bits LCD (with backlight), alternately
display T/RH, display area 47x27mm, with figure 16mm and
unit 2mm
Display panel material: PMMA
Resolution: 0.1°C(or °F , switchable), 0.1%RH
Update time: <1s
Power Supply:16~28VAC/19~35VDC
Consumption: 1.5 VA
Analog outputs:2×4~20mA(3/4 wires), RL<500Ω; accuracy as
low as 0.1%FS(T)/ 0.3%FS(RH)
Terminals: max Ø1.5mm2
Work Environment: 0~50°C , 0~95%RH (no cond.)
Storage Environment: -10~70°C
Front panel material: 316L stainless steel, 1.5mm thick
Back housing parts: fire retardant ABS+PC(UL94V-0)
Protection: front panel IP65
Weight: 330g
Approval: CE, meet EN61326-1 for industrial equipment
Note: For completeness, the above specifications include some of the
probe's function and technical parameters. The products are combination of
a main unit and a separated probe.
Models for the main unit (The product has two parts: the
main unit and the probe. This is only for the main unit)
Model
H17P
Flush Mount T/RH Display Unit/Transmitter (basic model)
Models for the probe (The product has two parts: the main
unit and the probe. This is only for the probe)
Model
Temp. and humidity probe, brand and accuracy
EE07-PFT3
E+E, 2%RH@0~90%RH/0.1°C @20°C
HC2A-S1.5-OEM
Rotronic, 1.5%RH/0.3°C @10~30°C , 23°C, 10/35/80%RH
HC2A-S
Rotronic, 0.8%RH/0.1°C @10~30°C , 23°C, 10/35/80%RH
HC2A-S-HH
Rotronic, 0.8%RH/0.1°C @10~30°C , 23°C, 10/35/80%RH,
Hydrogen peroxide probe
1. The cable should be ordered separately, with length of 2m, 5m or 10m. The models
for E+E are E2, E5 and E10 respectively, and for Rotronic are R2, R5 and R10.
2. The main unit, probe and cable should be selected and ordered respectively. For
example: the main unit is H17P, the probe is EE07PFT3 and the cable is E5. The
factory will deliver the three parts separately, and customer will install and connect
them on site. Please refer to the operation manual for details.
3. In the environment where the pharmaceutical factory uses hydrogen peroxide
disinfection, the hydrogen peroxide filter HA010115 is optional for the probe of E+E,
and the hydrogen peroxide probe HC2A-S-HH is optional for Rotronic to resist the
sensor erosion during the hydrogen peroxide disinfection process.
Electrical Connection
Due to the different selections, the terminals and wiring will be different, and the specific wiring should be wired according to the
corresponding wiring diagram of the product model.
H17P mainframe with EE07 probe wiring diagram: Brand E+E,Model EE07 probe cable wiring diagram:
Probe model
EE07
Cable
Cable color
white
brown
black
blue
argent
Electrical
signals
5V
GND
SCL
SDA
shield
H17P mainframe with HC2A probe wiring diagram: Brand Rotronic,Model HC2A Probe Cable Wiring Diagram:
Probe model
HC2A
Cable
Cable color
grey
green
blue
red
argent
Electrical
signals
GND
5V
TX
RX
shield
EE07-PFT3
V- V+
OUT-H OUT-T GND
GND 5V TX RX
1 2 3 4 5 6 7 8 9 10 11
AA
POWER SUPPLY
24VAC/DC
HTGND
Output
(4-20mA)
ON
1 2 3 4 5
SDA SCL
EE07
V- V+
OUT-H OUT-T GND
GND 5V TX RX
1 2 3 4 5 6 7 8 9 10 11
HC2A
AA
POWER SUPPLY
24VAC/DC
HTGND
Output
(4-20mA)
ON
1 2 3 4 5
SDA SCL

H17P Flush Mount T/RH Display Unit/Transmitter -Operation Manual Edition:A/1
2
ON
1 2
sw
0~50 0~100 -40~60 -20~80
ON
1 2
ON
1 2
ON
1 2
DIP Switch
"1" and "2" bits set temperature range:
0~50/100/-40~60/-20~80°C, 0~50°C is default
"3" bit set backlight: backlight on ON, no backlight on
OFF(default)
"4" bit sets temperature unit: °F at ON, °C at OFF (default)
Installation and instruction
The main unit is limited to indoor, with flush mount.
The basic installation mode of the main unit is glue bonding, with coating glue around the back of the front panel, flush in the
mounting hole, and pressing the front panel closely with the wall, to make sure the panel and the wall can be sealed.
The installation location of the main unit is NOT necessarily the actual "measuring point"." The "measuring point" should be the
actual installation location of the temperature and humidity probe.
Probe installation: inserted into the air duct, or fixed at the "measuring point".
Attention
Power-off the unit during installation and wiring, and a separate transformer is recommended when using a 24VAC power supply.
When sharing a 24VAC transformer with other devices such as controllers, transmitters, or valve drives, ensure that the polarity
(24V and GND) connections are completely correct, or they can cause unpredictable conditions and even damage the devices.
Make sure the input and output connections and DIP switch settings are correct. After the verification, power on the unit. It has a 30
seconds self-test process and then enters normal working status.
Warranty
It has limited warranty for eighteen (18) months after the production date.
Shenzhen TEREN Control Technology Co. Ltd.
Add: 3F, 2nd Industrial Zone, Nankeng, Longgang
District, Shenzhen, Guangdong, P.R.CHINA
Tel: [phone] Fax: [phone]
web: www.teren.com.cn
DIP switch
ON
1 2 3 4 5
ON
4
sw
℃℉
ON
4
ON
3
sw
no backlingt backlight
ON
3
TEREN website Alibaba shop