terveysilma Velco VLR-100 Parts list manual

NOTE!
• Maximum wall thickness 430mm. Hole-punching Ø 105mm.
• Make sure to adjust the valve before use.
• Attach this operating manual to the apartment maintenance book.
• Remember to replace the air lter at least once a year, when the lter surface gets heavily polluted.
• Use the silencer only if necessary (if the wall with a valve is located directly on the street), since the
silencer reduces the ow of air.
• One supply valve must be installed on every 20 m² area (applies Ø100 mm size).
• Velco thermostat supply valves have a 10-year product warranty.
Placement
• As high as possible on the wall, however at least 10 cm below the ceiling.
• Above or in direct connection with a window and a radiator.
• Avoid installation in proximity to electric wiring and water pipes.
Installation
1. Use long drill to mark-up the installation spot.
2. Use Ø105 mm hole punch and drill from inside to outside so that the tube slopes very slightly downwards. (approx. 1 mm/100
mm.) In order to prevent damage to the wall surface drill halfway through from each side.
3. Fit the required number of extension tubes to extend through the wall and seal with sealing agent. Depending on the wall
thickness, an additional wall tube may be used. If necessary the tube can also be cut.
4. If necessary: insert the silencer in tube black side facing outwards.
5. Assembly the air lter by installing the frame wires (2 pieces) in the holes located at the back of the vent. The wires can be
shortened if necessary. Seal the vent holes and wires with glue in order to facilitate lter replacement in the future.
6. To assemble the air lter, turn the lter upside down so that the uffy side is facing out and thread it over the wires.
7. Screw the vent cover clockwise until a clicking sound is heard, then adjust the valve half a turn to the left. The tting of the
valve is now complete.
8. Fix the vent in place. The sealing ring holds the valve in place so no further sealing with glue is needed. The vent is now
installed.
9. When replacing the lter, just carefully pull the tube out.
SUPPLY VALVE FOR A NEW LEAD TROUGH
Velco supply valve (VT-100) and lter with frame wires (S-100) Wall tube (VR-100) Extension tube (FR-100) Silencer (RE-97) Outer grille with extension tube (YG-100/FR-100)
250 150 150
97
40
150
25 20
3/22
VLR-100
puh. [phone]
Konalantie 47 F, 00390 Helsinki
terveysilma@terveysilma.
www.terveysilma.
The package consists of

ALWAYS USE ONLY THE VELCO ORIGINAL FILTER TO ENSURE THE PROPER FUNCTIONING OF THE VENTILATION
3/22
VELCO VS-100 FILTER REPLACEMENT GUIDE
The Velco VS-100 lter is made of high-quality Filtrete ™ material developed by 3M. The FiltreteTM material use exclusive
3-in-1 technology to pull in and trap unwanted particles, allowing cleaner air to ow through. Filtrete™ lters have an
electrostatic charge that acts like a magnet to attract and capture microscopic allergens.
1. Carefully pull out the valve from the wall
and remove the dirty lter.
2. Make sure the O-ring is in the
position shown in the picture. Pull the
lter carefully over the O-ring.
3. Turn the new lter inside out so that
the seams of the lter remain inside.
4. Turn the lter over the threads on
the valve.
6. The valve is now ready to be put
back in place. Rotate the valve in the
wall to seal the assembly. Adjust the
valve according to the adjustment
5. The exceeding part of the sock can
be stuffed into the lter’s framework.
VELCO VALVE ADJUSTMENT
Velco valve is equipped with a thermostat which automatically changes the air ow depending on the outside temperature.
The thermostat fully opens the valve at temperatures above + 10 ° C and closes it at temperatures below -5 ° C The valve is
adjusted according to the instructions to ensure continuous ventilation.
1. Screw the vent cover clockwise until
a clicking sound is heard.
2. Adjust the valve half a turn to the
left.
3. The tting of the valve is now complete.