Hunter 5931 User manual

www.HunterFan.com 1.888.830.1326
PAGE
5
30 inches
7 feet
PAGE
2
What to Expect with
Your Installation Ceiling Bracket
Ladder
PAGE
3
Tools Needed
Maintenance
& Cleaning Troubleshooting
Table of Contents
Canopy
PAGE
16
PAGE
18
Blades Glass
PAGE
17
PAGE
4
Mounting Options
PAGE
21
?
?
?
PAGE
22
Congratulations on purchasing your new Hunter® ceiling
fan! It will provide comfort and performance in your home
or ofce for many years. This installation and operation
manual contains complete instructions for installing and
operating your fan.
We are proud of our work and appreciate the opportunity
to supply you with the best ceiling fan available anywhere
in the world.
To register your fan, please visit:
www.HunterFan.com/register
Save your receipt for proof of purchase.
PAGE
6
PAGE
11
PAGE
14
WiringDownrod
Blade Irons & Top
Housing
PAGE
8
Light Kit
PAGE
20
Remote
Control Cradle
Remote Control
PAGE
19
1
M3622-01 • 10/19/16 • © 2016 Hunter Fan Company

www.HunterFan.com 1.888.830.1326
2
M3622-01 • 10/19/16 • © 2016 Hunter Fan Company
What to Expect with Your Installation
Know your wiring
If you are unfamiliar
with wiring, use a
qualied electrician.
You may need a
friend to help you.
Check box to see
fan weight
Assess location
30 inches
from blade tip
to nearest wall
or obstruction 7 feet
from bottom
edge of blade
to the oor
Select a downrod length
Assess ceiling angle
Must be able to
secure the fan to
building structure or
fan-rated outlet box
1
2
3
Standard Downrod
for ceilings 8-10 feet high
Shorter Downrod
for fans installed close to ceiling
Longer Downrod
for ceilings 10 feet or higher
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
w.1 - To reduce the risk of re, electrical shock, or personal injury,
mount fan directly from building structure and/or an outlet box marked
acceptable for fan support of 70 lbs (31.8 kg) and use the mounting
screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or servicing your
fan, disconnect the power by turning off the circuit breakers to the outlet
box and associated wall switch location. If you cannot lock the circuit
breakers in the off position, securely fasten a prominent warning device,
such as a tag, to the service panel.
w.3 - To reduce the risk of re, electrical shock, or motor damage, use only
Hunter Solid State Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the blade brackets when
installing the blade brackets, balancing the blades, or cleaning the fan. Do not
insert foreign objects in between rotating fan blades.
c.1 - All wiring must be in accordance with national and local electrical codes
ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualied electrician.
c.2 - Use only Hunter replacement parts.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and if not installed and used in accordance with the
instructions may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: modications not approved by the party responsible for compliance
could void user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Read and Save These Instructions
This product conforms to UL Standard 507.
WARNINGS
CAUTIONS

www.HunterFan.com 1.888.830.1326
Tools Needed
Ladder
Power Drill
(optional)
9/64” Drill Bit
(optional)
Screwdrivers
Pliers Wire Strippers
If mounting to a support structure, you will also need these tools.
Do not discard the hardware bags or mix
parts from different bags. Make note of
the symbol printed on each hardware
bag. The symbols can be used to identify
the appropriate hardware for each step.
3
M3622-01 • 10/19/16 • © 2016 Hunter Fan Company

www.HunterFan.com 1.888.830.1326
4
M3622-01 • 10/19/16 • © 2016 Hunter Fan Company
If you have an angled ceiling:
1. You will need a longer downrod (sold separately).
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Guide Touches
BOTH Ceiling & Wall
S
I
T
U
A
T
I
O
N
1
Guide Touches Wall
but NOT Ceiling
S
I
T
U
A
T
I
O
N
2
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
You need ONLY
a Longer
Downrod
*most common
If you have a at ceiling:
Hang your fan by a standard downrod (included).
Mounting Options
Use Standard Mounting
or Low-Prole Mounting
to hang the fan from a at ceiling.
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
34OCEILING
WALL
OPTION
1
Standard
Mounting
OPTION 2
Angled
Mounting
2 3
SLIDE
toward ceiling
PLACE
against wall
1
FOLD
on dotted line
34°
Use the three steps below to determine if your ceiling angle is greater than 34°
Support
Structure
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
Standard
Mounting
Style
Support
Structure
Ceiling
Outlet Box
(required)

www.HunterFan.com 1.888.830.1326
Ceiling Bracket
Refer to warning w.1 on pg. 2
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
For angled ceilings, point
opening toward peak.
If you are unable to do this,
call Technical Support at
1-888-830-1326.
Make sure all four bumpers are
still attached.
Use wood screws
(included) when securing
to support structure with
approved electrical outlet
box. Drill 9/64” pilot holes
in support structure to aid
in securing ceiling bracket
with hardware found in
the hardware bag.
Use machine screws
(provided with outlet
box) when securing to
existing ceiling fan-rated
outlet box. Make sure
it is securely installed
and is acceptable for fan
support of 31.8 kg (70 lbs)
or less.
OFF
Turn Power
5
M3622-01 • 10/19/16 • © 2016 Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Blade Irons & Top Housing
Place the motor in one of the holes in the packaging. Install a blade iron to the blade iron mounting
plate using two blade iron assembly screws,
found in the hardware bag. Repeat this
process to install all blade irons.
6
M3622-01 • 10/19/16 • © 2016 Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Blade Irons & Top Housing (continued)
You will need to ip the fan over before
proceeding to the next step.
Thread the wires through the
top housing.
Install the top housing screws.
These screws can be found in the
hardware bag.
7
M3622-01 • 10/19/16 • © 2016 Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Light Kit
Partially install two light kit assembly
screws, found in the hardware bag,
halfway into the motor housing as
shown. It does not matter which two
screw holes you choose.
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
Insert the third screw, found in
the hardware bag, into place and then
tighten all three screws.
8
M3622-01 • 10/19/16 • © 2016 Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Lower the light kit. Align the screw holes
in the light kit with the screw holes in the
upper switch housing.
Connect the plug connectors found in
the switch housing area of the light kit
assembly. Make sure to line up the colored
markings on the connectors.
Install the three switch housing screws,
found in the hardware bag, through
the light kit and into the switch housing.
Light Kit (continued)
9
M3622-01 • 10/19/16 • © 2016 Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Light Kit (continued)
Make sure the light kit assembly is securely attached to the
motor housing. Failure to properly secure all three assembly
screws could result in the light xture falling.
Connect the white wire from the fan to
the white wire from the light kit. Then,
connect the blue wire from the fan to the
black wire from the light kit. Lower the
LED assembly to the posts in the housing.
Attach the LED assembly using the
LED assembly screws found in the
hardware bag.
You will need to ip the fan over before
proceeding to the next step.
10
M3622-01 • 10/19/16 • © 2016 Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Downrod
Slide
Slide
1 2 3 4 5
678910
Sold Separately
Included
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
Shorter
Downrod
for fans installed
close to ceiling
Standard
Downrod
for ceilings 8-10’ high
Option 1Option 2
Option 3
skip to next page
If you need a different downrod length follow these steps:
Steps 1-5 to remove standard downrod pipe
Steps 6-10 to reassemble with new pipe
Included (pre-assembled)
11
M3622-01 • 10/19/16 • © 2016 Hunter Fan Company

www.HunterFan.com 1.888.830.1326
KEEP!
8”
3/8”
C
U
T
&
S
T
R
I
P
(not to scale)
Remove the pre-installed
setscrew so that the downrod
can be inserted.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
The wires can be cut, but
leave at least 8” extending
from the top of the
downrod.
Downrod (continued)
8” 3/8”
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
If the setscrew is not tightened
securely, the fan may fall.
K
E
E
P
!
12
M3622-01 • 10/19/16 • © 2016 Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Downrod (continued)
Put the wires and downrod through the
canopy. Let the canopy sit loosely on top
of the fan.
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
13
M3622-01 • 10/19/16 • © 2016 Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Wiring: Single Switch
Refer to CAUTION c.1 on pg. 2
Connect the white
(grounded) wire from
the ceiling to the white
wire from the fan.
Connect the three
grounding wires (green,
green/yellow stripe, or
bare copper) coming from
the ceiling, downrod, and
hanging bracket.
Connect the black wire
(ungrounded) from the
ceiling to the black wire
from the fan.
Cap the blue wire from
the fan. You will not
need it for single switch
wiring.
Note: To connect the wires,
hold the bare metal leads
together and place a wire
connector over them, then
twist clockwise until tight.
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Have a single switch?
Follow these steps:
Dual Switch
Instructions
Black
Blue
Green/Yellow Stripe
White
Ungrounded
Grounded
Grounding
G
r
e
e
n
/
Y
e
l
l
o
w
S
t
r
i
p
e
14
M3622-01 • 10/19/16 • © 2016 Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Grounded
Black
Blue
Green/Yellow Stripe
White
Ungrounded
Ungrounded (light)
Grounded
Grounding
G
r
e
e
n
/
Y
e
l
l
o
w
S
t
r
i
p
e
Wiring: Dual Switch
Refer to CAUTION c.1 on pg. 2
Connect the white
(grounded) wire from
the ceiling to the white
wire from the fan.
Connect the black wire
(ungrounded) from the
ceiling to the black
wire from the fan.
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Have dual switches?
Follow these steps:
Connect the second
ungrounded (light)
wire from the
celing to the blue
wire from the fan.
Connect the three
grounding wires (green,
green/yellow stripe, or
bare copper) coming from
the ceiling, downrod, and
hanging bracket.
Note: To connect the wires,
hold the bare metal leads
together and place a wire
connector over them, then
twist clockwise until tight.
15
M3622-01 • 10/19/16 • © 2016 Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Canopy
Lift the canopy into place so that
the screw holes are aligned.
Position the canopy so that, when
lifted into place, the canopy ts into
the hanging bracket as shown.
Screw
Holes
Insert the two canopy screws
found in the hardware bag.
16
M3622-01 • 10/19/16 • © 2016 Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Blades
Secure each blade to a blade iron as
shown using the blade nuts, found in the
hardware bag, and the blade assembly
screws, found in the hardware bag.
17
M3622-01 • 10/19/16 • © 2016 Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Glass
Carefully lift the globe up inside
the light xture as far as it will go.
Rotate the globe in a clockwise
direction until it is held tightly in
place by the three tabs.
Position the notches in the
outer rim of the globe so they
line up with the tabs on the
light kit assembly.
Notch
Tab
CONGRATULATIONS!
YOU’RE DONE!
See next page for fan
operation instructions.
18
M3622-01 • 10/19/16 • © 2016 Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Remote Control
To access the battery compartment, remove
the small Phillips head screw that secures the
battery door to the transmitter assembly. The
battery should be installed with the positive
(+) side up. Replace with a CR2032 battery
when necessary.
Phillips
Head
Screw
Battery
Door ON
Turn Power
The remote transmitter is already paired to the
receiver and ready to use.
Note: If your need to pair your remote, remove the battery
door. Cycle power to the fan by turning power off and back on
at the wall switch (or circuit breaker if necessary). Within three
minutes, press the pair button on the remote. If pairing was
successful, a single beep will sound. If three beeps sound, the
remote was unpaired. Re-pair using the steps above.
To prevent faulty operation, please disconnect power from
all other ceiling fans within range while pairing.
19
M3622-01 • 10/19/16 • © 2016 Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Remote Control Cradle
Option 1: Using Screws
Option 2: Using Adhesive Strip
Install the cradle bracket to the wall with
the included screws.
You have two options to install the included remote control cradle
to the wall. Choose which path works best for you.
Choose your cradle installation location.
If you are installing into drywall, drill two
9/64 width holes using the cradle bracket
as a guide. Gently hammer the included
drywall anchors into the pre-drilled holes. Press the cradle bracket
against the wall and hold
rmly for 30 seconds.
Apply the adhesive sticker
to the back of cradle
bracket per the instructions
on the adhesive sticker.
Slide the cradle onto the
mounted bracket.
Remove the cradle from
the cradle bracket.
20
M3622-01 • 10/19/16 • © 2016 Hunter Fan Company