Texas Instruments TPA701 User manual

November 1998 Mixed-Signal Products
TPA701 MSOP Audio Power
Amplifier Evaluation Module
User’s Guide
SLOU026A

IMPORTANT NOTICE
TexasInstrumentsanditssubsidiaries(TI)reservetherighttomakechangestotheirproductsortodiscontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TIdeemsnecessarytosupportthiswarranty. Specifictestingofallparametersofeachdeviceisnot necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICALAPPLICATIONS.INCLUSIONOFTIPRODUCTSINSUCHAPPLICATIONSISUNDERSTOODTO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TIassumesnoliabilityforapplicationsassistance or customer product design. TI does not warrantorrepresent
thatanylicense,eitherexpressorimplied,isgrantedunderanypatentright,copyright,maskworkright,orother
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright 1998, Texas Instruments Incorporated

iii
Chapter Title—Attribute Reference
Preface
Related Documentation From Texas Instruments
J TI Plug-N-Play Audio Amplifier Evaluation Platform (literature
number SLOU011) provides detailed information on the evaluation
platform and its use with TI audio evaluation modules.
J TPA701 700-mW LOW-VOLTAGE AUDIO POWER AMPLIFIER
(literature number SLOS229) This is the data sheet for the TPA701
audio amplifier integrated circuit.
FCC Warning
This equipment is intended for use in a laboratory test environment only. It
generates, uses, and can radiate radio frequency energy and has not been
testedfor compliance with the limitsofcomputingdevices pursuant to subpart
Jofpart 15of FCCrules, whicharedesignedtoprovidereasonableprotection
against radio frequency interference. Operation of this equipment in other
environments may cause interference with radio communications, in which
case the user at his own expense will be required to take whatever measures
may be required to correct this interference.
Trademarks
TI is a trademark of Texas Instruments Incorporated.

iv

Running Title—Attribute Reference
v
Chapter Title—Attribute Reference
Contents
1 Introduction 1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1 Feature Highlights 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 Description 1-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3 TPA701 EVM Specifications 1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Quick Start 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1 Precautions 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2 Quick Start List for Platform 2-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3 Quick Start List for Stand-Alone 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Details 3-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1 Precautions 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2 The TPA701 MSOP Audio Amplifier Evaluation Module 3-3. . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.1 TPA701 Audio Amplifier IC 3-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.2 BTL Operation 3-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.3 Module Gain 3-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4 Shutdown 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3 Using The TPA701 MSOP EVM With The Plug-N-Play Evaluation Platform 3-6. . . . . . . . .
3.3.1 Installing and Removing EVM Boards 3-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.2 Signal Routing 3-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.3 Mute/Mode 3-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.4 Power Requirements 3-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.5 Inputs and Outputs 3-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4 Using The TPA701 MSOP EVM Stand-ALone 3-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.1 TPA701 MSOP EVM Connected for BTL Output 3-11. . . . . . . . . . . . . . . . . . . . . . . .
3.5 TPA701 MSOP Audio Amplifier Evaluation Module Parts List 3-12. . . . . . . . . . . . . . . . . . . .

Running Title—Attribute Reference
vi
Figures
1–1 The TI TPA701 MSOP Audio Amplifier Evaluation Module 1-3. . . . . . . . . . . . . . . . . . . . . . . . . .
2–1 Quick Start Platform Map 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–2 Quick Start Module Map 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–1 The TI Plug-N-Play Audio Amplifier Evaluation Platform 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–2 TPA701 MSOP EVM 3-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–3 TPA701 MSOP EVM Schematic Diagram 3-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–4 TPA701 Audio Amplifier IC 3-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–5 Platform Signal Routing and Outputs 3-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–6 Mute/Mode and Polarity Control 3-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–7 Typical Headphone Plug 3-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–8 TPA701 MSOP EVM Connected for Stereo BTL Output 3-11. . . . . . . . . . . . . . . . . . . . . . . . . . .
Tables
2–1 Typical TI Plug-N-Play Platform Jumper and Switch Settings for the
TPA701 MSOP EVM 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–2 Platform Jumper and Switch Settings for the TPA701 MSOP EVM 2-3. . . . . . . . . . . . . . . . . . .
3–1 TPA701 MSOP EVM Parts List 3-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-1
Introduction
Introduction
This chapter provides an overview of the Texas Instruments (TI) TPA701
MSOPAudioAmplifierEvaluationModule(SLOP213).ItincludesalistofEVM
features, a brief description of the module illustrated with a pictorial diagram,
and a list of EVM specifications.
Topic Page
1.1 Feature Highlights 1–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 Description 1–3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3 TPA701 MSOP EVM Specifications 1–4. . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1

Feature Highlights
1-2
Introduction
1.1 Feature Highlights
The TI TPA701 MSOP Audio Amplifier Evaluation Module and the TI
Plug-N-Play Audio Amplifier Evaluation Platform include the following
features:
- TPA701 Low-Voltage Audio Power Amplifier Evaluation Module
J Single channel, bridge-tied load (BTL)
J 3.3-V and 5-V operation
J 700-mW output power into 8 Ωat 5 V, BTL
J Ultra-low current consumption in shutdown mode
J Internal thermal and short-circuit protection
J Module gain is set at –4 V/V in BTL mode, –2 V/V in SE mode
- Quick and Easy Configuration with The TI Plug-N-Play Audio Amplifier
Evaluation Platform
J Evaluation module is designed to simply plug into the platform,
automatically making all signal, control, and power connections
J Platform provides flexible power options
J Jumpers on the platform select power and module control options
J Switches on the platform route signals
J Platformprovides quick and easyaudio input and outputconnections
- Platform Power Options
J On-board 9-V battery
J External 5-V – 15-V (VCC) supply inputs
J External regulated VDD supply input
J Socket for on-board 5 V/3.3 V VDD voltage regulator EVM
J On-board overvoltage and reverse polarity power protection
- Platform Audio Input and Output Connections
J Left and right RCA phono jack inputs
J Miniature stereo phone jack input
J Left and right RCA phono jack outputs
J Left and right compression speaker terminal outputs
J Miniature stereo headphone jack output

Description
1-3
Introduction
1.2 Description
The TPA701 MSOP Audio Power Amplifier Evaluation Module is a complete,
low-power single-channel audio power amplifier. It consists of the TI TPA701
700-mW Low-Voltage Audio Power Amplifier IC in a very small MSOP
package, along with a small number of other parts mounted on a circuit board
that is approximately one and a quarter inches square (Figure 1–1).
Figure 1–1.The TI TPA701 Audio Amplifier Evaluation Module
OUT+
IN
GND
Vdd GND
U1 †
R2
Shutdown
R3
OUT–
GND
C3
TEXAS
INSTRUMENTS
SLOP213
TPA701 MSOP EVM
C5
C2
C1 C4
S1 R1
+
†Due to the very small size of the MSOP IC package, the standard part number TPA701 is replaced with the code TIABA.
Single in-line header pins are mounted to the underside of the module circuit
board to allow the EVM to be plugged into the TI Plug-N-Play Audio Amplifier
EvaluationPlatform or to be wired directlyintoexistingcircuitsand equipment
when used stand-alone.
The platform has room for a pair of TPA701 MSOP evaluation modules and
is a convenient vehicle for demonstrating TI’s audio power amplifier and
related evaluation modules. The EVMs simply plug into the platform, which
automatically provides power to the modules, interconnects them correctly,
andconnectsthemtoaversatilearrayofstandardaudioinputandoutputjacks
and connectors. Easy-to-use configuration controls allow the platform and
EVMs to quickly model many possible end-equipment configurations.
There is nothing to build, nothing to solder, and nothing but the speakers
included with the platform to hook up.

TPA701 EVM Specifications
1-4
Introduction
1.3 TPA701 EVM Specifications
Supply voltage range, VDD 2.5 V to 5.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supply current, IDD 450 mA, max. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous output power, PO:8-ΩBTL, VDD=5 V 700 mW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio input voltage, VI2 Vpp, max. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Minimum load impedance, RL8 Ω. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-1
Quick Start
Quick Start
ThestepsinthischaptercanbefollowedtoquicklypreparetheTPA701MSOP
audio amplifier EVM for use. Using the TPA701 MSOP EVM with the TI
Plug-N-Play Audio Amplifier Evaluation Platform is a quick and easy way to
connectpower,signalandcontrolinputs,andsignaloutputstotheEVM,using
standard connectors. However, the audio amplifier evaluation module can be
usedstand-alonebymakingconnectionsdirectlytothemodulepins,anditcan
be wired directly into existing circuits or equipment.
Theplatform switch and jumper settings shown in Table 2–1 are typical for the
TPA701 MSOP EVM. They will cause the TPA701 device to shutdown when
a plug is inserted into platform headphone jack J10.
Table 2–1. Typical TI Plug-N-Play Platform Jumper and Switch Settings for the TPA701
MSOP EVM
EVM JP6 JP7 JP8 S2 S3
TPA701 Mute X Hi Note 2 X
Notes: 1) X = Don’t care
2) SetS2to ONwhen signal conditioningboard isinstalled in U1;set S2
to OFF when no signal conditioning board is installed.
Topic Page
2.1 Precautions 2–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2 Quick Start List for Platform 2–3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3 Quick Start List for Stand-Alone 2–4. . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 2

Precautions
2-2
Quick Start
2.1 Precautions
Power Supply Input Polarity and Maximum Voltage
Always ensure that the polarity and voltage of the external power
connected to VCC power input connector J1, J2, and/or VDD power
input connector J6 are correct. Overvoltage or reverse-polarity
power applied to these terminals can open on-board soldered-in
fuses and cause other damage to the platform, installed evaluation
modules, and/or the power source.
Inserting or Removing EVM Boards
Do not insert or remove EVM boards with power applied – damage
to the EVM board, the platform, or both may result.
Figure 2–1. Quick Start Platform Map
3
110
9
8
6b
6b
6a
6b
5
4
6b
2
Signal Conditioning
****CAUTION****
Do not insert or remove
EVM boards with power
applied
ICC
JP4
F1
VR1
R1
JP3
JP2
JP1 AC/DC
(J2) VCC(J1)
D1 D2 D3
D4 J2
J3 J4 J5
AC/DC
In
VCC
In
+
J1
DC
SOURCE
LED1 VCC
LED2
VDD
R2
JP5 IDD
B1
U6
POWER
SUPPLY
U3 U4
U5
U1
U2
Audio
Power
Amps
On
Off ConditioningS2
J7 J8 Right
Out Left
Out
+–+–
JP6
Mode
Mute
Spk(U2-U4)
JP8
J9 Left
Out
JP7 S3
HP Source
U2-U4
U5
Polarity
Lo
Hi
HP(U5)
C3 C2
++
R3
R4 R5
J10
Stereo
HP Out
TP1 GND
Plug-N-PlayAudio Amplifier
Evaluation Platform
SLOP097 Rev. C.1
Stereo
In
Right
In Left
In
J6 In/Out VDD
F2
VR2
+
DC
Power
In/Out
Speaker
Output
Headphone
Output
Audio
Input
Power
Input
Batt
C1+
Right
Out
On Off Pwr
S1
TEXAS INSTRUMENTS 1997

Quick Start List for Platform
2-3
Quick Start
2.2 Quick Start List for Platform
Follow these steps when using the TPA701 MSOP EVM with the TI
Plug-N-Play Audio Amplifier Evaluation Platform (see the platform user’s
guide, SLOU011, for additional details). Numbered callouts for selectedsteps
are shown in Figure 2–1 and details appear in Chapter 3.
- Platform preparations
1) Ensurethatallexternalpowersourcesaresetto
OFF andthattheplatform
power switch S1 is set to
OFF.
2) Install a TPA701 MSOP module in platform sockets U3 and U4 for stereo
operation (or a module in either U3
or U4 for single channel operation),
taking care to align the module pins correctly.
3) Use switch S2 to select or bypass the signal conditioning EVM (U1).
4) Set control signal Polarity jumper JP8 to
Hi.
5) Set jumper JP6 to select the Mute control input (causes the TPA701 to
shutdown if a plug is inserted into platform headphone jack J10).
Table 2–2. Platform Jumper and Switch Settings for the TPA701 MSOP EVM
EVM JP6 JP7 JP8 S2 S3
TPA701 Mute X Hi Note 2 X
Notes: 1) X = Don’t care
2) SetS2 to
ON whensignal conditioning boardis installed inU1; set S2
to
OFF when no signal conditioning board is installed.
- Power supply
6) Select and connect the power supply:
a) Connectan external regulated power supplysettoa voltage between
2.5Vand5.5VtoplatformVDD powerinputconnectorJ6, takingcare
to observe marked polarity, or
b) InstallavoltageregulatorEVM(SLVP097orequiv.)inplatformsocket
U6. Install a 9-V battery in B1 or connect a 7 V – 12 V power source
to a platform VCC power input J1 or J2 and jumper the appropriate
power input (see platform user’s guide).
- Inputs and outputs
7) Ensure that signal source level is set to minimum.
8) Connect the audio source to left and right RCA phono jacks J3 and J5 or
stereo miniature phone jack J4.
9) Connect 8-Ω– 32-Ωspeakers to left and right RCA jacks J7 and J9 or to
stripped wire connectors J8.
- Power-up
10) Verifycorrect voltage and input polarityand set the external power supply
to
ON. IfVCCandanon-boardregulatorEVMareusedtoprovideVDD,set
platform power switch S1 to
ON.
PlatformLED2shouldlightindicatingthepresenceofVDD,andtheevaluation
modules installed on the platform should begin operation.
11) Adjust the signal source level as needed.

Quick Start List for Stand-Alone
2-4
Quick Start
2.3 Quick Start List for Stand-Alone
Follow these steps to use the TPA701 MSOP EVM stand-alone or when
connecting it into existing circuits or equipment. Connections to the TPA701
MSOP module header pins can be made via individual sockets,
wire-wrapping, or soldering to the pins, either on the top or the bottom of the
module circuit board. Numbered callouts for selected steps are shown in
Figure 2–2 and details appear in Chapter 3.
Figure 2–2. Quick Start Module Map
5
2
6
4
OUT+
IN
GND
Vdd GND
U1 †
R2
Shutdown
R3
OUT–
GND
C3
TEXAS
INSTRUMENTS
SLOP213
TPA701 MSOP EVM
C5
C2
C1 C4
S1 R1
+
†Due to the very small size of the MSOP IC package, the standard part number TPA701 is replaced with the code TIABA
- Power supply
1) Ensure that all external power sources are set to
OFF.
2) Connect an external regulated power supply set to 5 V to the module Vdd
and GND pins, taking care to observe marked polarity.
- Inputs and outputs
3) Ensure that the signal source level is set to minimum.
4) Connect the audio source to the module IN and GND pins, taking care to
observe marked polarity.
5) Connect the Shutdown (S1) pin to VDD througha NormallyOpen switch.
6) Connect an 8-Ω– 32-Ωspeaker to the module OUT+ and OUT– pins.
- Power-up
7) Verifycorrect voltage and input polarityand set the external power supply
to
ON.
The EVM should begin operation.
8) Adjust the signal source level as needed.

3-1
Details
Details
This chapter provides details on the TPA701 IC, the evaluation module, the
stepsin theQuick-StartList, additionalapplicationinformation, andapartslist
for the TPA701 MSOP evaluation module.
Topic Page
3.1 Precautions 3–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2 The TPA701 MSOP Audio Power Amplifier Evaluation Module 3–3. .
3.3 Using The TPA701 MSOP EVM With The Plug-N-Play
Evaluation Platform 3–6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4 Using The TPA701 MSOP EVM Stand-Alone 3–11. . . . . . . . . . . . . . . . . . . .
3.5 TPA701 MSOP Audio Power Amplifier Evaluation
Module Parts List 3–12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 3

Precautions
3-2
Details
3.1 Precautions
Power Supply Input Polarity and Maximum Voltage
Always ensure that the polarity and voltage of the external power
connected to VCC power input connector J1, J2, and/or VDD power
input connector J6 are correct. Overvoltage or reverse-polarity
power applied to these terminals can open on-board soldered-in
fuses and cause other damage to the platform, installed evaluation
modules, and/or the power source.
Inserting or Removing EVM Boards
Do not insert or remove EVM boards with power applied – damage
to the EVM board, the platform, or both may result.
Figure 3–1.The TI Plug-N-Play Audio Amplifier Evaluation Platform
Signal Conditioning
****CAUTION****
Do not insert or remove
EVM boards with power
applied
ICC
JP4
F1
VR1
R1
JP3
JP2
JP1 AC/DC
(J2) VCC(J1)
D1 D2 D3
D4 J2
J3 J4 J5
AC/DC
In
VCC
In
+
J1
DC
SOURCE
LED1 VCC
LED2
VDD
R2
JP5 IDD
B1
U6
POWER
SUPPLY
U3 U4
U5
U1
U2
Audio
Power
Amps
On
Off ConditioningS2
J7 J8 Right
Out Left
Out
+–+–
JP6
Mode
Mute
Spk(U2-U4)
JP8
J9 Left
Out
JP7 S3
HP Source
U2-U4
U5
Polarity
Lo
Hi
HP(U5)
C3 C2
++
R3
R4 R5
J10
Stereo
HP Out
TP1 GND
Plug-N-PlayAudio Amplifier
Evaluation Platform
SLOP097 Rev. C.1
Stereo
In
Right
In Left
In
J6 In/Out VDD
F2
VR2
+
DC
Power
In/Out
Speaker
Output
Headphone
Output
Audio
Input
Power
Input
Batt
C1+
Right
Out
On Off Pwr
S1
TEXAS INSTRUMENTS 1997

The TPA701 MSOP Audio Power Amplifier Evaluation Module
3-3
Details
3.2 The TPA701 MSOP Audio Power Amplifier Evaluation Module
The TPA701 MSOP Audio Power Amplifier Evaluation Module is powered by
a TPA701 700-mW Low-Power Audio Amplifier IC and includes an on-board
shutdown control signal switch.
The module can be used with the TI Plug-N-Play Audio Amplifier Evaluation
Platform (Figure 3–1) or wired directly into circuits or equipment. The module
has single in-line header connector pins mounted to the under side of the
board. These pins allow the module to be plugged into the TI platform, which
automatically makes all the signal input and output, power, and control
connections to the module.
The module connection pins are on 0.1-inch centers to allow easy use with
standard perf board and plug board-based prototyping systems. Or, the EVM
can be wired directly into existing circuits and equipment when used
stand-alone.
The module appears in Figure 3–2 and its schematic is shown in Figure 3–3.
Figure 3–2.TPA701 MSOP EVM
OUT+
IN
GND
Vdd GND
U1 †
R2
Shutdown
R3
OUT–
GND
C3
TEXAS
INSTRUMENTS
SLOP213
TPA701 MSOP EVM
C5
C2
C1 C4
S1 R1
+
†Due to the very small size of the MSOP IC package, the standard part number TPA701 is replaced with the code TIABA
Figure 3–3.TPA701 MSOP EVM Schematic Diagram
C1
1 µF
C2
1 µF
R1
20 kΩ
Audio Input–
GND
Shutdown S1
C5
5 pF
OUT–
GND
OUT+
R3
39 kΩ
R2
20 kΩ
No
C3
10 µF
C4
1 µF
Shutdown
Bypass
In+
In–
VO–
GND
VDD
VO+
8
7
6
5
1
2
3
4
GND
VDD
2.5 V to 5.5 V
+

The TPA701 MSOP Audio Power Amplifier Evaluation Module
3-4
Details
3.2.1 TPA701 Audio Amplifier IC
TheTPA701audioamplifierICisaCMOSdeviceintendedforbridge-tiedload
(BTL) operation in battery-powered applications. It is supplied in a very small
surface-mount package and has been designed to operate from low supply
voltages (between approximately 2.5 V and 5.5 V) and deliver up to
approximately 700 mW into an 8-Ω, BTL (Figure 3–4). Typical applications
include portable phones, toys, games, and similar hand-held audio
applications.
Figure 3–4.TPA701 Amplifier IC
5
OUT+
4
IN –
OUT–
8
3
IN+
_
_
+
+
7
2VDD/2
VDD
GND
6
Bias Control
SHUTDOWN
1
BYPASS
The IC includes two separate internal amplifiers. The two amplifiers operate
as mirror images of each other for increased power. BTL operation provides
many benefits, including quadruple the output power of single-ended
operation and no need for bulky output coupling capacitors. For more
information, see the TPA701 amplifier IC data sheet, TI Literature Number
SLOS229.
3.2.2 BTL Operation
The output signal from OUT+ must go through the speaker load and be
returned directly to OUT–, and
NOT to system ground. This requires that the
OUT– line be isolated not only from system ground, but also from the OUT–
linesofanyotheramplifiersinthesystem.Theplatformprovidessuchisolated
output lines from the amplifier EVM sockets directly to separate left and right
speaker connectors.
3.2.3 Module Gain
The TPA701 MSOP evaluation module has a set gain of 2. However, the gain
can be adjusted to a maximum of 22 by changing the value of resistor R3
(Figure 3–3). Use the following equation to determine value of R3:
Gain +
–R3
R2
2 for BTL

The TPA701 MSOP Audio Power Amplifier Evaluation Module
3-5
Details
The TPA701 amplifier IC, like most other amplifiers, exhibits its best distortion
andnoiseperformanceatlowergainlevels(seetheTPA701datasheet).Even
so, the TPA701 at its highest gain setting has significantly less distortion than
most low-cost speakers.
Gain versus total harmonic distortion (THD) should be considered in each
application.BoththemoduleinputsignallevelandtheTPA701MSOPmodule
gain should be adjusted to obtain the lowest overall distortion level for a
particularoverallgain.Aquickrule ofthumb (everythingelse beingequal):the
module input signal level should be as high as possible without clipping or
overloading the TPA701 input, and the TPA701 gain should be kept as low as
possible.
3.2.4 Shutdown
When the shutdown terminal of the TPA701 amplifier IC is taken high, the IC
ceases operation and enters an ultra-low power state. This is accomplished
by applying a control signal to the module Shutdown pin or by pressing the
Shutdown switch, S1, on the module. When the control signal goes low or is
removed (or the switch is released), amplifier operation resumes.
The Plug-N-Play platform can generate the shutdown (mute) signal for the
moduleeither when a plug is
inserted into the platform headphone output jack
or when the plug is
removed , as selected by a platform jumper (JP8).

Using The TPA701 MSOP EVM With the Plug-N-Play Evaluation Platform
3-6
Details
3.3 Using The TPA701 MSOP EVM With the Plug-N-Play Evaluation Platform
The TPA701 MSOP Audio Amplifier Evaluation Module was designed to be
used with the TI Plug-N-Play Audio Amplifier Evaluation Platform. It simply
plugs into socket U3 or U4.
The following paragraphs provide additional details for using the TPA701
MSOP EVM with the platform.
3.3.1 Installing and Removing EVM Boards
TI Plug-N-Play evaluation modules use single-in-line header pins installed on
the underside of the module circuit board to plug into sockets on the platform.
The EVM pins and the platform sockets are keyed such that only the correct
type of EVM can be installed in a particular socket, and then only with the
proper orientation.
Evaluation modules are easily removed from the platform by simply prying
them up and lifting them out of their sockets. Care must be taken, however, to
prevent bending the pins.
3.3.1.1 EVM Insertion
1) Remove all power from the evaluation platform.
2) Locate socket U3 or U4 on the platform.
3) Orient the module correctly.
4) Carefully align the pins of the module with the socket pin receptacles.
5) Gently press the module into place.
6) Check to be sure that all pins are seated properly and that none are bent
over.
3.3.1.2 EVM Removal
1) Remove all power from the evaluation platform.
2) Using an appropriate tool as a lever, gently pry up one side of the module
a small amount.
3) Changetotheoppositesideofthemoduleanduse thetooltoprythatside
up a small amount.
4) Alternate between sides, prying the module up a little more each time to
avoid bending the pins, until it comes loose from the socket.
5) Lift the EVM off of the platform.