Texi SIRIUS User manual
Operation Manual
Laser Machine
SIRIUS
Security Considerations
Before operating the equipment, it is strongly recommended that the users should read this
specification and follow the operation manual strictly and NOBODY is allowed to start up
the machine EXCEPT THE PROFESSIONALS.
This equipment adopts four kind of laser device (Strong laser radiation), the radiation may
cause the following accident: 1) Fire the tinder surroundings. 2) While processing, some
other radiation and toxic, harmful gases may appear depend on the material. Direct laser
radiation can do harm to human body. Therefore, fire-fighting equipment must be prepared
around where the machine stands. It is strictly forbidden to put flammable, explosive articles
around the table and equipment, while keeping the good ventilation, non-professional
personnel is allowed near the equipment.
Manufacturing objects and emissions should accord with local laws and regulations.
Laser processing may cause risks, users should carefully consider whether processed object
is suitable for laser operation or not.
High voltage or other potential danger may be inside the laser equipment, we insist you
assemble it under the guidance of factory professionals.
When the equipment powered on, it should be attended and not left without man watching.
POWER OFF THE EQUIPMENT BEFORE YOU LEAVE.
When laser equipment is processing, it’s forbidden to open any end cover.
Before the machine is powered on, it should be earthed as well as the relevant accessories.
It is strictly prohibited to placed any irrelevant total reflection or diffuse reflection object near
the equipment, prevent the laser reflection from doing harm to the body or flammable items.
When the operation is in process, the operator must watch the status of the equipment at any
moment, if abnormal condition occurs, the power supply of the machine should be cut off
immediately and corresponding measures should be taken in time.
The surrounding environment should be dry, without pollution, no vibration, no strong electric,
strong magnetic interference and influence. Working temperature 5-40 ℃, humidity 5-95% (non
condensate).
This laser cutter enegraver should be far away from the electrical-sensitive equipment, for
itmay produce electromagnetic interference.
Working voltage: AC220V, 50HZ. When the voltage is not stable or does not match the
machine, it is strictly prohibited to boot the equipment.
*For any loss of improper Operation or violation against the items above, we
are not responsible for it.
Catalog
A Appearance of the machine and accessories
B Process for installing machine
C Laser tube installation and optical path adjusting
D Software installation (Attached)
E Equipment operating instructions (Attached)
F Daily maintenance of machine and analysis of common problems to solve
G Warranty terms
H Attachment
Appearance of the machine and accessories:
Pic 1-1
The whole appearance
The whole appearance
Pic 1-2
Power cord
Pic 1-3
Connection of the whole machine and the accessories
Pic 1-4
Air pump
Pic 1-5
Machine foundation
Pic 1-6
The blower pipe clamp
Pic 1-7
The laser signal line
The connector of water
in or out
Water chiller
Pic 1-8
The exhauster pipe
Pic 1-9
Blower
Pic 1-10
Chiller accessories
Pic 1-11
English
operation
panel
Pic 1-13
Laser tube installation：
Please notice when customers is in the installation of the laser tube
A In the positive and negative pole connected to the situation of optical laser tube, the anode is
the light side, the electrode is the laser tube with spiral side as shown in Figure 1-14 (laser tube
high pressure cap), such as wrong would lead to the laser tube damage
The water inlet
Outlet of
water
Laser tube base
Pic 1-14
B Installation of the laser tube should be lightly not encountered any place, put the laser tube
on the laer tube base steady and Tighten the relevant screws.
C Laser tube outlet should be from the first reflector to a distance of at least 3-5CM as shown
in Figure 1-15.
Negative
electrode line
The first reflector frame
Pic 1-15
D Water work, in order to prevent the laser tube having the bubble phenomenon, take the way
that make the water from low to higher as shown in Figure 1-2 (cathode in anode out, low into
higher refers to the inlet and outlet of the laser tube).
Laser tube installation and adjusting optical path:
Engraving machine in the process of using ,a variety of reasons may occur light path offset,
resulting in no light or optical phenomenon is not correct, please refer to the following methods
optical path adjustment:
Laser tube
Pic 1-16
The first step: make sure the light from the laser tube can be launched in the first Reflector
center. (light spot should be complete)
Adjusting screw and nut
Pic 1-17
The second step: when you adjust the second reflector ,stick on light block on it (can make objects),
move the beam to the position most close to the first frame , press the pulse button (point click),
marking the mark (Attention: please use the non metal sheet metal shielding to prevent the laser
radiation hurt , test spot about the location , and then adjusted). Gradually move the beam to the
farthest from the first reflector position, then press the pulse, make a mark. If the two markers do
not coincide, adjust the copper screws on the first reflector , so that the two laser spot center mark
coincidence (repeated debugging until the two marks overlap completely).
The second reflecting mirror
Adjusting screw and nut
Pic 1-18
The third step: adjust the third reflector and attached to the light block(The laser head) on it,move
the laser head to the position that nearest the second reflector. Put the pulse button . Make sure far
beam and the dipped beam overlap completely,and the light spot should be in the light hole center of
the laser head.( The laser head cut out object in the middle of the machine ( watch the verticality)
Auxiliary air tube
Laser head
Pic 1-19
Laser tube
Pic 1-20
The fourth step: if the laser does not fall within the light hole center, such as deviation: to raise
or lower the light pipe. And deviation: only second reflector inwards or outwards adjustment.
(such as adjusting the laser tube or a reflector position need to redo the second step and the third
step, the spot completely Coincidence)
Diagram of center adjustment
Pic 1-21
Attention please : The above work, the operator must be trained professionally before operation
Production equipment maintenance
Equipment’s routine maintenance is reduce the wear to make the equipment always in a
basic work with good technology condition. The basic requirements of routine maintenance are:
Operator use the equipment should strictly follow the rules,always observe the working condition
of the equipment,the device should be kept intact,accessories should kept tidy,complete the safety
equipment,wiring,and plumbing should intact; individual parts of equipment should always
wipe, kept free of grease, no oil, kept in flexible operation.
First, boot the equipment
Check whether the power ,electrical control switches and the knobs are safe and reliably;
whether the location of each control mechanism, transmission parts, stop dog, limit switch
position is normal; each operation is well lubricated sliding parts, oil cup, hole, oil lines,
etc.whether fuel is sufficient ; check whether the oil cup, oil level and oil filters are clean. After
confirming all normal can start commission. At startup and commissioning, you should check
whether the work situation of all parts have the abnormal phenomena and sound.
Second,release the water and clean the water tank.( recommended clean and replacement
the circulating water once a week)
Note: Before the machine work must ensure that the laser tube is filled with circulating water.
Circulating water quality and temperature directly affect the life of laser tube, it is recommended to use pure
water, and controlled the water temperature below 35℃. If more than 35℃ need to replace the circulating
water or add ice cubes to the water to reduce the temperature.
Clean water tank: First turn off the power, unplug the water saliva pipe, allowing water
of laser tube to automatically flow into the tank, open the tank, remove the pump, clean the
pump. Clean the tank , replace circulating water, reverts back the pump to the tank, connect
the pump pipe insert inlet, collated the joints. The pump is powered separately and run for
2-3 minutes (make the laser tube filled with circulating water).
Third,the use of fan.
Use the fan for a long time will make the internal fan accumulate a lot of solid dust. Make
the fan have a lot of noise. And it not conducive to the exhaust and remove sapor.When the fan
suction insufficient and exhaust poor, first turn off the power,discover the air out/in from the
duct, remove the dust inside of the fan, then upside down the fan, move the fan blade until clean
, then install the fan. And according to dosage clean it regular.
Fourth, cleaning lens
It’s recommended that clean before work and must be operate at the machine in the off state.
Clean focus lens:take the focus lens off from mirror bracket,bens the lent cleaning paper,wet it
with professional cleaning fluid or ethanol,gently wipe the lens surface of the lens with a damp paper
repeated several times until the mirror clean.
Note:
① gently wipe the lens and should not damage the surface coating;
② wiping process should gently to prevent falls;
③ Please be sure that the convex upward at install the lens
Fifth, clean rail (recommended cleaned once every two weeks,operations when shut down ) Rail, linear
shaft as one of the core components of the device, due to the different pieces of processed material and
some special materials will generate a lot of dust and corrosive fumes during processing, has a great
influence on the accuracy and the life of the equipment, in order to ensure the machine;s normal steady
work and ensure quality of processed products, must in accordance with
regulations regularly routine maintenance the rails, linear axis.
Note: Clean the rails please prepare - dry cotton and lube
First, ensure that the machine in the case of power failure, move the laser head to the far right
(or left), wipe clean with a dry cloth until shiny (kerosene can help you clean it up), and then use
lube (can use sewing machine oil, do not use engine oil), slowly push the laser head around a few
times, so that oil can be evenly distributed
Sixth ,fastening screws and coupling
Equipment in use for some time, you should test the connection, avoid connecting screws
and coupling come loose, which affect the smooth of mechanical movement, so you should
observe whether the transmission components of the machine there have abnormal noise or
anomalies at working, found the problem should promptly rugged and maintenance. At the same
time the device should use certain tools individually sturdy screws. The first test should be after
use the equipment one month and take the text once every three months.
Seventh, laser tube cleaning
1,Pay attention to protect the laser output window to avoid the generated smoke sputtered
to the output window surface at work process (including the debugging optical path process),
prevent the outer surface of the output window to polluted, leading to power down, can use cotton
or silk dip ethanol gently wipe the outer surface of the output window;
2, Pay attention to clean the dust grease on the laser tube, to avoid the accumulation of dust
in the vicinity of high-voltage electrode that resulting in high-voltage ignition. Laser tube should
be regularly cleaned at outage.
Eighth,maters need attention of daily operate.
(1) Strictly in accordance with procedures using the machine. Can’t appear illegal operation.
(2) Do not place the tool, measure gauge, clamp, cutting tools, workpieces, raw materials
,etc.on the machine. Ensure that activities guide surface and rail junction surface without chips,
dust, no oil, rust and other phenomena.
(3) At the equipment revolving,must have a professional operator, rigorous off-site,
unattended and so on.
(4) After equipment have errors, the power should bu probably cut off,you should contact
with the professional repairman, rigorous appear boot secondary damaged phenomenon .
(5)When the machine stops working,you should clean the machine comprehensively. The
equipment work areas hold be clean and tiny no oil or waste on the ground; equipment
accessories should be complete, properly, clean.
In order to ensure the normal operation of the equipment to extend the service life of the
equipment operator, routine maintenance, each shift before the end of the work, the holiday and
festival before the holiday time should maintain the machine in accordance with the regular
maintenance to the continuous operation equipment cannot Shutdown maintenance. Complete
maintenance rules specified in the work content and requirements.
C
ommon problems of laser cutting engraving system
No.
Analysis method
Treatment method
phenomenon
1 Boot
but
1.Check whether
the
1.check the electrical wires
machine is not
machine electricity is ok
again
start
2.check
the
main
2.set up the parameters refer
parameters
is correct
by software instructions
2
1.Adjust the
light path
1.Check wether the optical
Working
path skewing
2.Judgment
with
plug
the
without laser
rays into the power of the
2.Line problem
signal terminal
3 The laser
on 1.Check whether the water
1.Clean the water tank and
and off at
cycle is ok
water pump,clear the pipe
work
2.whether
the
supply 2.Add voltage stabilize to
voltage is stabilize
power supply
4 The online 1.whether
the
1.Shutdown
and
reconnect
data
can’t
be communication cable
is
the cable
disposed
connected
2.Reinstall the software and
2.whether
the software USB drive
USB is installed
5
Processing
1.Install the software
1.install
the original
size does
not
2.Adjust action
software to recover original
consistent
parameters
with
software
2.sized
the
working
area
set
and trim size .calculate refer
to software
6 The control 1.Line is loose
Check whether
the
panel
no
connecting
line
is
loose
light
from main board to panel
7 Boot
reset
is There is
problem of limit
Check
parameter
of
limited
switch and signal
software
and limit
switch
setting
8 Carving
1Electrostatic interference
1.Reconnect
ground
wire
dislocation
2.Drive parts is loose
two meters below ground
2.Check if the gear top silk
and strap is loose
Warranty clause
Thank you for purchasing our laser machine.We have to announce to you that if you operate
don’t according to specified items in “operating manual” ,we don’t warranty the damage of the
machine.
One. The content and deadline of the warranty
1 Warranty contents
If the laser engraving machine you have buy generate quantity problem due to the material or
manufacturing below the mark, our company will warranty refer to terms of the warranty period
given.
2 Warranty deadline
Since the whole year from the date of purchase, (particular parts guarantee period please see
the attached sheet)
Two. Some unsuitable issues of warranty.
1. beyond the warranty period or can’t provide the machine warranty card.
2.can be considered that the phenomenon has no effect on performance,just is sensuousness (eg:
sound, vibration, static electricity, etc.)
2. the use of losses and long aging (such as: painting, spray, plating, plastic parts
3. naturally fade cracking, etc.).
4. Failure to perform the obligation according to the contract.
5. Unused high-quality hardware provided by our company to and purchase hardware by self.
6. Damage from dust,chemicals and other similar factors.
7. Damage caused by the non-specified maintenance department of our company’s dismantled
repair.
8. Damage caused by force majeure such as natural disasters,fire,theft,etc..
Table of contents
