Texmate CL-B101D40-RTD User manual

CL-B101D40-TCRTD Manual (d0099) Page 1

CL-B101D40-TCRTD

Smart 101 segment 4 digit LED Tricolor or Mono-color

digital bargraph controller with four fully programmable

set points for J, K, R, and T type thermocouples and

RTD inputs in a switchboard style case.

0.56” LEDs

•

External transmitters or signal conditioners can be eliminated by

direct connection of the sensor output to Plug-in Input Signal

Conditioners- available are thermocouples (J, K, R and T types)

or RTD (Pt-100. 385 and 392 curves. 3 wire/4wire). Digitally

Linearized.

•

Optional isolated 16 bit analog output. User or factory scalable to 4

to 20 mA, 0 to 20 mA or 0 to 10 V across any desired digital span

from ± one count to the full scale range of – 1999 to 9999 (12000

counts).

•

A Programmable Tricolor (Red-Green-Orange) or mono color (red or

green), 101 segment high brightness bargraph.

•

Red 4-digit LED display with a range of -1999 to 9999

(12000 counts). Optional green digital display.

•

Front panel LED annunciators provide indication of setpoint status.

•

Two 9 Amp Form C, and two 4 Amp Form A or 4 x 4 Amp Form A

relays available

•

Auto-sensing AC/DC power supply. For voltages between

85-265 V AC / 95-300 V DC (PS1) or 18-48 V AC / 10-72 V DC

(PS2).

•

Provision to connect an external programming lockout switch.

•

Provision for external DIM switch to reduce the brightest

display setting by 50%.

•

Automatic intelligent averaging, smooths noisy signals while

providing a fast display response to real level changes.

General Features

Specifications

• Thebargraphcandisplay,full

scale, any desired portion of

the digital reading.

• Setpoint1hasdelay-on-make

and delay-on-break plus

a special “pump on pump

off” mode that creates a

Hysteresis Band between SP1

and SP2.

Software Features

•

Four programmable setpoints

with adjustable Hysteresis.

•

Bargraph center zero function.

• Relayactivationcanbeselect-

ed to occur above (hi) or below

(Lo) each setpoint.

• Digitaldisplayblanking.

• Decimalpointsetting.

• Four-levelbrightnesscontrol

LEOPARD

FAMILY

Input Specs:�� Depends on Input signal conditioner

A/D Converter:�� 14 bit single slope

Accuracy:�� ±(0�05% of reading + 2 counts)

Temp. Coeff�: �� 100 ppm/°C (Typical)

Warm up time:�� 2 minutes

Conversion Rate:�� 10 conversions per second (Typical)

Digital Display:��

4 digit 0.56" LED red (std), green (optn)

Range

–1999 to 9999 counts�

Bargraph Display:��

101 segment 235º circular red (standard),

Green (optional) or tricolor (optional) LED�

Polarity:�� Assumed positive� Displays – negative

Decimal Selection:�� Front panel button selectable, X•X•X•X•

Positive Overrange:�� Bargraph and top segments of digital display

flash�

Negative Overrange:�� First segment of bargraph and bottom seg-

ments of digital display flash�

Relay Output:�� Two 9 Amp Form C relays, two 4 Amp Form

A relays or

4 x 4 Amp Form A relays

Analog Output:�� Isolated 16 bit user scalable mA or V

OIC (mA out) ��

4-20 mA @ 0 to 500Ω max loop resistance

OIV (volts out) �� 0-10 V DC @ 500 Ω or higher resistance

Power Supply:�� AC/DC Auto sensing wide range supply

PS1 (std)��

85-265 VAC / 95-300 VDC, 50-400Hz 4.2W

PS2��

18-48 VAC / 10-72 VDC, 50-400Hz 4�2W

Operating Temp�: �� 0 to 60°C

Storage Temp:�� –20°C to 70°C

Relative Humidity:�� 95% (non condensing)

Case Dimensions:��

Bezel (4.48"x4.48") 113.8x113.8mm

Depth behind bezel (4.23") 107.46 mm

Plus (0�48”) 12�24 mm for connectors

Weight:�� 16 oz�, 1lb 4 oz when packed

Table of Contents

Bargraph Center Point Display Mode Selection ... 6

Bargraph Color Programming Mode ........ 9

Case Dimensions ...................... 11

Component Layout..................... 11

Connector Pinouts ...................10-11

Controls and Indicators .................. 2

Decimal Point and Brightness Selection ..... 5

Programming Conventions................ 2

Setpoint Setting & Relay Conf. Mode ......8-9

Software Features ...................... 1

Software Logic Tree ..................... 3

Specifications.......................... 1

Two Point Analog Range Setting & Calibration .... 7

Thermocouple and RTD Type Selection Mode......4

Digital Span Selection for Bargraph Display .. 5

Digital Span Selection for Analog Range Output... 6

Functional Diagram .................... 10

General Features ....................... 1

Input Module Calibration Procedures ...... 12

Ordering Information ................... 13

Pin Descriptions ....................... 10

Page 2 CL-B101D40-TCRTD Manual (d0099)

Front Panel Buttons

Program Button

The

button is used to move from one program step to the next.

When pressed at the same time as the button, it initiates the

calibration mode. When pressed at the same time as the but-

ton, it initiates the setpoint setting mode.

101 Segment

Bargraph

Up Button

When in the operational display, pressing the button allows you

to view the setting of the saved Peak and Valley Values.

When setting a displayed parameter during programming, the

button is used to increase the value of the displayed parameter.

Down Button

When in the operational display, pressing the button allows you

to change the Brightness Level as well as to view the setting of

the setpoints SP1, SP2, SP3 & SP4.

When setting a displayed parameter during programming, the

button is used to decrease the value of the displayed parameter.

Front Panel LED Display

Annunciator LEDs

The annunciator LEDs indicate the alarm status. They are labeled

from bottom to top: SP1, SP2, SP3, SP4.

Digital LED Displays

The digital LED displays are used to display the meter input

signal readings. They also display the programming settings

during programming.

Setpoint Indication

The position of setpoints on the bargraph display are indicated by

an ON or OFF segment dependent on the bargraph display being

above or below the setpoint.

Setpoints

indicated

by an ON

Segment

Setpoints indicated

by an OFF Segment

Controls and Indicators

This symbol represents the

OPERATIONAL DISPLAY.

This is the PROGRAM button.

This is the UP button.

This is the DOWN button.

When a button is shown, press and

release it to go onto the next step in the

direction indicated by the arrow. When

an alternative dotted line is shown, this

indicates that an alternative logic branch

will be followed when a particular option

is present.

When two buttons are shown side by side

and enclosed by a dotted line, they must

be pressed at the same time then released

to go onto the next programming step.

If an X appears through a digit, it means that

any number displayed in that digit is not rel-

evant to the function being explained.

[Span]

[10000]

When the

and

buttons are shown

together, the display value can be increased

by pressing and releasing the

button

or decreased by pressing and releasing the

button.

When the

and

buttons are shown

with two displays, either display can be

selected by pressing and releasing the

buttons.

When two displays are shown together

with bursts, this indicates that the display is

toggling (flashing) between the name of the

function and the value.

Text or numbers shown between square

brackets in a procedure indicate the pro-

gramming code name of the function or the

value displayed on the meter display.

When there are more than two display selec-

tions they are shown in brackets below the

first display and are also selectable by

pressing and releasing the

buttons.

A dotted line enclosing an entire logic dia-

gram indicates that programming branch

will appear only when a particular option is

present.

To explain software programming procedures, logic diagrams are

used to visually assist in following the programming steps. The

following symbols are used throughout the logic diagrams to

represent the buttons and indicators on the meter:

Programming Conventions

[X•XXX]

[XX•XX]

[XXX•X]

[XXXX•]

[XXXX]

Front Panel Controls and Indicators

LED

Annunciators

for Setpoints

1-4

Single or

Tri-color

Bargraaph

Display

Button

DOWN

Button

PROGRAM

Button

7 Segments

Digital

Display

CL-B101D40-TCRTD Manual (d0099) Page 3

Software Logic Tree

The CL-B101D40-TCRTD is an intelligent bargraph meter with a

hierarchical software structure designed for easy programming

and operation, as shown below in the software logic tree.

Software Version is Displayed on Power-up

When power is applied, all segments of the bargraph and

digital display light up for 3 seconds. The version number of

the installed software is then displayed for 2 seconds, after

which, the operational display indicates the input signal.

15 Second Program Timeout

Except for ZERO and SPAN settings in the Analog Output Range Setting and

Calibration Mode (cLo and chi), the meter has a 15 second program timeout. If

no buttons are pressed for 15 seconds in any of the other programming

sequences, the meter will exit the programming mode and return to the opera-

tional display. Any program changes that were made prior to pressing the

button in the preceding step will not be saved.

[orAn]

[rEd]

[H]

[L]

NOTE: Will only

appear if a tricolor

display is installed

[orAn]

[rEd]

[orAn]

[rEd]

[orAn]

[rEd]

[orAn]

[rEd]

BARGRAPH COLOR

PROGRAMMING MODE

See Page 9

Tricolor Bargraph

The tri-color bargraph is designed

like a traffic light, to display either

red, orange or green, but only one

color at a time. The color to be

displayed is selected in two ways.

The first step is to select the color to

be displayed when the bar is “below”

whichever set point is set to the

lowest position.

The second step is to select the color

to be displayed when the bar is

above each specific setpoint,

regardless of the order or position to

which the set points are set.

However, if two or more setpoints

with differently specified colors are

positioned at the same set point

value, the color specified for the set

point with the highest identifying

number will be displayed.When

setpoints are set to the same value,

the SP4 color overrides the SP3

color, the SP3 color overrides the

SP2 color, and the SP2 color

overrides the SP1 color.

Set Setpoint 1

(SP1)

Delay-on-Make

(doM)

Delay-on-Break

(dob)

0 to 9999 seconds

Relays

Activation

[rLYS] (H) High

the relay

energizes when

the setpoint is

exceeded

[rLYS] (L) Low

the relay

energizes below

the setpoint.

Setpoint 2 (SP2)

NOTE: [dom] [dob]

Functions are only

available for SP1

0 to 9999 seconds

Pump (PUM)

Hysteresis (hYSt)

Setpoint 3 (SP3)

Setpoint 4 (SP4)

Operational Display

MAIN MENU

BRIGHTNESS AND

SETPOINT VIEW MODE

Bargraph Center Point

Display Selection (cto)

This branch will

only appear if

the analog

output option

is installed

Back to

Operational

Display

Digital Display ON/OFF

Selection (diSP)

Sub-menu MODE

Calibration Mode

Calibration

Input

Calibration

Output

Calibrate Analog

Output Lo

Calibrate Analog

Output Hi

Select the Digital

Reading at which

the Analog Output

Hi (chi) will occur

Select the Digital

Reading at which

the Analog Output

Lo (cLo) will occur

This branch will only appear

if the analog output option

is installed

DIGITAL SPAN SELECTION

FOR ANALOG RANGE OUTPUT

See Page 6

DIGITAL DISPLAY ON/OFF

See Page 6

BARGRAPH CENTER POINT

DISPLAY MODE SELECTION

See Page 6

TWO POINT ANALOG OUTPUT

RANGE SETTING AND CALIBRATION

See Page 7

Bargraph Display

Scale Lo Range

Setting (bLo)

Bargraph Display

Scale hi Range

Setting (bhi)

Display

Brightness (br)

1 Dimmest

2 Dim

3 Bright

4 Brightest

BRIGHTNESS SELECTION

See Page 5

DIGITAL SPAN SELECTION

FOR BARGRAPH DISPLAY

See Page 5

if Analog Output is not installed,

goes directly to Input selection

–

4.00

–

20.00

1 Dimmest

2 Dim

3 Bright

4 Brightest

SETPOINT SETTING AND

RELAY CONFIGURATION MODE

See Page 8

H or L

SP1

[H]

[L]

SP2

[H]

[L]

SP3

[H]

[L]

SP4

[K]

[r]

[t]

If RTD module is installed

this menu will appear.

3 or 4 wire

RTD input

selection

RTD select type

P385 or P392

If Thermocouple module is

installed this menu will appear.

Resolution select

Thermocouple

select

Select J, K, R or T

1°

0.1°

Degree select

°C

°F

THERMOCOUPLE OR RTD TYPE,

RESOLUTION AND DEGREE

C OR °F SELECT

See Page 4

Pump On Pump Off

When PUM is selected ON,

and SP2 is set at a value

higher than SP1, the SP1

relay will operate in

a special "pump on pump off"

Hysteresis mode. SP2 acts

as the upper limit and SP1

acts as the lower limit of the

Hysteresis Band.

For filling applications, rLYS

should be set to LhLh. SP1 will

then activate for inputs less than

the SP1 setpoint, and remain

ON until the SP2 setpoint is

reached.

For emptying applications,

rLYS should be set to hhhh.

SP1 will then activate for inputs

greater than the SP2 setpoint,

and remain ON until the SP1

setpoint is reached.

Peak

[PEAK]

Reset

PEAK

Reset

VA LY

Valley

[VALY]

PEAK & VALLEY

VIEW & RESET

FL-B101D40H_LogicTree_v2.0

°C

°F

Displays °C or °F whichever

is the opposite of the

selected operational display

Page 4 CL-B101D40-TCRTD Manual (d0099)

STEP A Enter the Calibration Mode

Press the

and buttons at the same time.

Display toggles between [CAL] and [oFF].

2) Press the or button. Display changes from [oFF]

to [on].

3) Press the

button.

STEP B If the Display toggles between [CAL] and [out] the

optional Analog Output hardware is installed. In which

case select [CAL] [out]. Display toggles between [thEr]

or [rtd] depending on whether a IT10 Thermocouple

Input Module or a IT11 RTD Input Module are detect-

ed by the soft ware. If no optional output hardware is

installed the menu will skip directly to STEP C.

STEP C Sensor Type Selection

1) Using the and buttons, adjust the display

to the desired sensor type.

2) Press the

button. Display toggles between

[rES] resolution select and previous [rES] setting.

STEP D Set the Resolution

1) Using the and buttons, adjust the display

to the desired resolution [rES] value.

Press the

button.

Display toggles between

[dEG] and previous [dEG] selection.

STEP E Selection of Degree C or Degree F

1) Using the and buttons, adjust the display to

either ˚C or ˚F.

2) Press the

button.

Calibration Procedure

MAIN MENU

Operational Display

Sub-menu

MODE

STEP A Calibration

Mode

STEP B Calibration

Mode

To Digital Span Selection for

Bargraph Display Page 5

cAL out/iP branch will only appear if

the analog output option is installed,

otherwise cAL on goes directly to step c.

To Digital Span Selection

for Bargraph Display

See Page 6

To Two Point Analog

Output Range Setting

and Calibration

See Page 7

[K]

[r]

[t]

If RTD module is installed

this menu appears

3 or 4 wire

RTD input

selection

RTD select type

P385 or P392

If Thermocouple module is installed

this menu appears

Resolution select

Thermocouple select

Select J, K, R or T

STEP C

STEP D

STEP E

1°

0.1°

Degree select

°C

°F

THERMOCOUPLE OR RTD TYPE,

RESOLUTION AND DEGREE C OR F SELECT

Input Sensor Reso-

lution °C Range °F Range

J T/C

K T/C

R T/C

T T/C

100ΩRTD (385 curve)

100ΩRTD (392 curve)

-120 to 760°C

-120.0 to 530.0°C

-120 to 1370°C

-120.0 to 530.0°C

0 to 1760°C

0 to 530.0°C

-120 to 400°C

-120.0 to 400.0°C

-200 to 800°C

-199.9 to 530.0°C

-200 to 800°C

-199.9 to 530.0°C

-200 to 1400°F

-199.9 to 999.9°F

-200 to 2500°F

-199.9 to 999.9°F

32 to 3210°F

32.0 to 999.9°F

-200 to 750°F

-199.9 to 750.0°F

-200 to 1470°F

-199.9 to 999.9°F

-200 to 1470°F

-199.9 to 999.9°F

Sensor Range Table

1°

0.1°

1°

0.1°

1°

0.1°

1°

0.1°

1°

0.1°

1°

0.1°

Thermocouple type or RTD type selection mode

Input Module Calibration Procedure

See page 12 for the Calibration instructions of each Input Module type.

CL-B101D40-TCRTD Manual (d0099) Page 5

Example

From Thermocouple

or RTD Type Selection

Mode See Page 4

STEP A

STEP B

See Example Above

of Bargraph Display

Scale Range

DIGITAL SPAN SELECTION

FOR BARGRAPH DISPLAY

STEP C

To Digital Span Selection

for Analog Range Output or

Bargraph Center Point

Display Mode Selection

on Page 6

STEP A Enter the Calibration Sub Menu Mode

1) Press the

and buttons at the same time.

Display toggles between [CAL] and [oFF].

2) Press the

button. Display toggles between

[bhi] and the previous setting.

STEP B Set the Digital Span of the Bargraph Display (See

example above)

1) Using the and buttons, adjust the display

to the desired high parameter reading, e.g.

6000 counts.

2) Press the

button. Display toggles between

[bLo] and the previous setting.

3) Using the and buttons, adjust the display

to the desired low parameter reading, e.g. 4000

counts.

4) Press the

button. Display changes from

[4000] to [dP].

Brightness Selection

STEP C

Press the

button. Display toggles between [br]

and the previous brightness setting.

Set the Bargraph and Digital Display Brightness

1) Using the and buttons, adjust the display

to the desired brightness setting (4 is the

brightest setting).

2) Press the

button. Display toggles between

[Anhi] and the previous [Anhi] setting.

Note: If at this point, the display skips directly to STEP G and

toggles between [Cto] and [oFF], the software is detecting

that the optional analog output hardware is NOT installed.

Digital Span Selection For Bargraph Display

Bargraph does not light

up for Input Signals up to

3999 counts

Bargraph lights up for

Input Signals above

4000 counts

Bar

High

Bar

Low

Bar

High

Bar

Low

25 75

100

25 75

100

No bargraph display

Digital display

No bargraph display

Digital display

An example of setting the

digital span of the bargraph

display to be different than

the digital display range

The bargraph can be set to display full scale (0-101 bars) any portion

of the digital reading from a minimum of 100 counts to a maximum of

12,000 counts. This provides higher resolution bargraph indication for

those applications where the normal operating input signal range is less

than the desired full scale display range of the digital display.

For Example:

If the full scale range of the meter has been set from -1999 to

9999 (0-12,000 counts), but the normal operating range of the

input signal is between 4000 & 6000. The bargraph high parame-

ter [bhi] can be set to 6000 and the bargraph low parameter [bLo]

can be set to 4000.

This means that although the meter could digitally display a signal

from -1999 to 9999 (0-12,000 counts), the bargraph display only

begins to function at a reading of 4000, and reaches full scale

indication at a reading of 6000. Although the digital display will

continue reading up to 9999 before indicating overrange, the bar-

graph display will indicate its overrange by flashing for readings

above 6000.

Page 6 CL-B101D40-TCRTD Manual (d0099)

Example of Using the Center Point Bargraph Display Mode

with a Unipolar Input

If the meter's full scale range is set to 5000 counts, the midpoint would

be 2500 counts. If a signal of 2500 counts is applied only one segment at

the 2500 count mark will light up. If a signal of 4000 counts is applied the

segments between the center segment (2500 counts) and the 4000 count

mark light up.

If a signal of 1000 counts is applied, the segments between the center seg-

ment (2500 counts) and the 1000 count mark will light up.

Example of Using the Center Point Bargraph Display Mode

with Bipolar Signal Inputs

The meter may also be calibrated to display symmetrical bipolar signals such

as ± 1 V or ± 10 V. When the center point display mode is selected, it will

then function as a center zero meter. When positive signals are applied, the

bar will go up from the center point, and when negative signals are applied,

the bar will go down from the center point.

STEP E Selecting the [Anhi] Digital Value for Analog High Output

1) Using the and buttons, adjust the display to the desired

digital value at which the [chi] Calibrated Analog High output will

occur. For digital readings outside the digital span selected, the

analog output will linearly rise above the value set for chi, up to the

maximum analog output capability. However, the analog output will

not go lower than the calibrated value set for cLo (see below).

2) Press the

button. Display toggles between [AnLo] and

previous [AnLo] setting.

STEP F Selecting the [AnLo] Digital Value for Analog Low Output

1) Using the and buttons, adjust the display to the desired

digital value at which the [cLo] Calibrated Analog Low output will

occur. For Digital readings outside the Digital Span selected, the

analog output will not go lower than the calibrated value set for

cLo.

2) Press the

button. The display toggles between [cto] and

[oFF].

Note: Any two digital span points from –1999 to 9999 can be selected. The digital

values for [Anhi] analog high and [AnLo] analog low can be reversed to provide a 20 to

4mA output. The digital span selected can be as small as two counts, when using the

analog output to function as a Control or Alarm Driver. Small digital spans will cause

the high resolution 16 bit D to A to increment digitally in stair case steps.

Digital Span Selection for Analog Range Output

Bargraph Center Point Display Mode Selection

STEP G

Bargraph Center Point Mode Selection (See example above)

1) To select bargraph center point mode, press the or

button. Display changes from [oFF] to [on].

2) Press the

button. Display toggles between [diSP] and

[on] or [oFF].

STEP H Digital Display ON/OFF Selection

1) To set the display to [oFF], press the or button.

Display toggles between [diSP] and [oFF].

2) Press the

button. The display exits the calibration mode

and returns to the operational display. Only the bargraph

display is on and the digital display is off.

If the digital display is selected to be off, pressing any button to

make programming changes or to view setpoints activates the digital display.

When the procedure is complete, the digital display will then automatically

switch off.

The Display/Bargraph settings are now complete.

Operational Display

STEP G

STEP H

See Example of Bargraph

Center Point Display Mode

Selection Above

From Digital Span Selection

for Analog Range Output Above

or Direct From Decimal Point

and Brightness Selection Page 5

if Analog Output Option is Not Present

BARGRAPH CENTER POINT

DISPLAY MODE SELECTION

STEP E

STEP F

This branch will only

appear if the analog

output option is installed

To Bargraph Center

Point Display Mode

Selection Below

From Decimal Point and

Brightness Selection

See Page 5

DIGITAL SPAN SELECTION

FOR ANALOG RANGE OUTPUT

-1V +1V

0.800

-0.800

-1V +1V

Center Point

Single Bar Lit

Center Point

As signal

increases

Digital display

Center Point

As signal

decreases

Digital display

05000

5000

2500

4000

5000

2500

1000

Center Point

Single Bar Lit

Center Point

As signal

increases

Digital display

Center Point

As signal

decreases

Digital display

Unipolar Signal Input Bipolar Signal Input

CL-B101D40-TCRTD Manual (d0099) Page 7

Operational Display

Sub-menu

MODE

STEP A Calibration

Mode

STEP B Calibration

Mode

STEP E

Calibrate

Analog

Output

STEP F

Calibrate

Analog

Output

Will only appear if the analog

output option is installed

To Digital Span Selection

for Bargraph Display

See Page 5

To Thermocouple

or RTD Selection

Mode See Page 4

Operational Display

TWO POINT ANALOG OUTPUT

RANGE SETTING AND CALIBRATION

–x

4.00

–x

20.00

Determine if the Analog Output Selection Header is in the 4 to 20mA

(0-20mA) position or the 0 to 10VDC position. If necessary, the mod-

ule may have to be removed and the header position changed (see

Component Layout below).

Note: Always disconnect power from the meter before removing the

analog output module to adjust the mA or Volts output selection head-

er and reinstalling it. When power is reconnected, the meter’s software

will automatically detect the presence or absence of the analog output

module.

STEP A Enter the Calibration Mode

Press the

and buttons at the same time. Display

toggles between [cAL] and [oFF].

Press the or button. Display changes from [oFF] to

[on].

Press the

button. Display toggles between [cAL] and

[out] input calibration.

Note: If at this point the display skips directly to toggle between

Zero and the previous Zero setting, the software is detecting that the

optional analog output hardware is NOT installed.

STEP B Enter the Two Point Analog [ouT] Output Range Setting

and Calibration Mode

Press the

button. Display toggles between [cLo] and an

internal scale factor.

STEP E Set or Calibrate [cLo] the Low Analog Value of the

Analog Output Range

Connect a multimeter to analog output pins 17 and 18

(see Rear Panel Pinouts on page 10). Using the and

buttons, adjust the analog output to the desired low value as

measured on the multimeter. cLo may be adjusted to any

value from –0.3 mA to 18 mA (mA output selected) or from

–0.6 V to 8 V (volt output selected). However, the output of

cLo must always be less than the value selected for chi. If a

reversed analog output is desired, the values selected to

establish the Digital Span can be reversed (see top of page

6). For digital readings outside the Digital Span selected, the

analog output will not go any lower than the calibrated value

set for cLo. However, the analog output will linearly rise

above the value set for chi, up to the the maximum analog

output capability (see chi below).

Press the

button. Display toggles between [chi] and an

internal scale factor.

STEP F Set or Calibrate [chi] the High Analog Value of the

Analog Output Range

1) Using the and buttons, adjust the analog output

to the desired high value as measured on the multimeter

display. chi may be adjusted to any value from 18 mA to

24 mA (mA output) or from 8 V to 10.3 V (volt output).

However, the value must be higher than the value select-

ed for cLo. For digital readings outside the Digital Span

selected, the analog output will linearly rise above the

value set for chi, up to the maximum analog output capa-

bility.

2) Press the

button. The meter exits the calibration

mode and returns to the operational display.

Note: The analog output range established by the values selected

for cLo and chi will occur, automatically scaled, between the two

digital values selected for AnHi and AnLo. However, the analog

output can linearly rise above the chi value set for digital readings

outside the digital span selected. See Digital Span Selection on

page 6.

Two Point Analog Output Range Setting and CalibrationTwo Point Analog Output Range Setting and Calibration

Page 8 CL-B101D40-TCRTD Manual (d0099)

Operational Display

SETPOINT SETTING

AND RELAY

CONFIGURATION MODE

STEP A

STEP B

STEP C

STEP D

No [doM] or [dob]

STEP E

STEP F

STEP G

STEP H

STEP I

STEP J

STEP K

STEP L

To Step M of Setpoint

Setting and Relay

Configuration Page 9

The following programming steps are required to enter the setpoint values and configure the relay functions

in a meter with four relays using four setpoints� Generally if less than four relays are installed, the setpoints

without relays are operational in software for tri-color control or display only purposes� To remove unwanted

setpoint indications, set them to 9999 or -1999 depending on the relay activation mode selected�

STEP A Enter the Setpoint Mode

1) Press the

and buttons at the same time� Display toggles between [SP1] and the previous

SP1 setting�

STEP B Set Setpoint 1 [SP1]

1) Using the and buttons, adjust the display to the desired SP1 value�

2) Press the

button� Display toggles between [doM] and the previous [doM] setting�

STEP C Set the SP1 Delay-on-Make [doM] Delay Time Setting

Using the and buttons, adjust the display to the desired [doM] value (0 to 9999 seconds)�

The reading must continuously remain in an alarm condition until this delay time has elapsed before

the relay will make contact (energize)�

2) Press the

button� Display toggles between [dob] and the previous [dob] setting�

STEP D Set the SP1 Delay-on-Break [dob] Delay Time Setting

Using the and buttons, adjust the display to the desired [dob] value (0 to 9999 seconds)�

The reading must continuously remain in a non-alarm condition until this delay time has elapsed

before the relay will break contact (de-energize)�

2) Press the

button� Display toggles between [hYSt] and the previous [hYSt] setting�

STEP E Select the Hysteresis [hYSt]

Using the and buttons, select the Hysteresis to be ON or OFF�

2) Press the

button� Display toggles between PUM and (on) or (oFF)�

STEP F Select Pump [PUM] (on) or (oFF)

Using the and buttons, select the Pump to be ON or OFF� When PUM is selected ON, and

SP2 is set at a value higher than SP1, the SP1 relay will operate in a special "pump on pump off" mode�

SP2 acts as the upper limit and SP1 acts as the lower limit of the Hysteresis Band on the SP1 relay�

For filling applications:

[rLYS] should be set to [LhXX] (see step M)� The SP1 relay and SP1 LED Annunciator will then activate for inputs

less than the SP1 setpoint, and remain ON until the SP2 setpoint is reached�

For emptying applications:

[rLYS] should be set to [hhXX] (see step M)� The SP1 relay and SP1 LED Annunciator will then activate for inputs

greater than the SP2 setpoint, and remain ON until the SP1 setpoint is reached�

2) Press the

button� Display toggles between [SP2] and the previous SP2 setting�

STEP G Set Setpoint 2 (SP2)

1) Using the and buttons, adjust the display to the desired SP2 value�

2) Press the

button� Display toggles between [hySt] and the previous [hySt] setting�

STEP H Select the Hysteresis [hYSt]

1) Using the and buttons, select the Hysteresis to be ON or OFF�

2) Press the

button. Display toggles between [SP3] and the previous [SP3] setting.

STEP I Set Setpoint 3 (SP3) (No [doM] or [dob])

1) Using the and buttons, adjust the display to the desired SP3 value.

2) Press the

button� Display toggles between [hySt] and the previous [hySt] setting�

STEP J Select the Hysteresis [hYSt]

1) Using the and buttons, select the Hysteresis to be ON or OFF�

2) Press the

button� Display toggles between [SP4] and the previous [SP4] setting�

STEP K Set Setpoint 4 (SP4) (No [doM] or [dob])

1) Using the and buttons, adjust the display to the desired SP4 value�

2) Press the

button� Display toggles between [hySt] and the previous [hySt] setting�

STEP L Select the Hysteresis [hYSt]

1) Using the and buttons, select the Hysteresis to be ON or OFF�

2) Press the

button� Display toggles between [rLYS] and the previous relay setting�

Please Continue On Next Page.

Setpoint Setting and Relay Configuration Mode

CL-B101D40-TCRTD Manual (d0099) Page 9

STEP M

STEP N

STEP O

STEP P

STEP Q

STEP R

STEP S

STEP T

STEP U

[orAn]

[rEd]

NOTE: Will only

appear if a tricolor

display is installed

[orAn]

[rEd]

[orAn]

[rEd]

[orAn]

[rEd]

[orAn]

[rEd]

BARGRAPH COLOR

PROGRAMMING MODE

Operational Display

From From Step L of

Setpoint Setting and Relay

Configuration Page 8

L or h

To comply with the latest safety requirements, the tri-color bargraph is designed like a traffic light, to

display either red, orange or green, but only one color at a time. When the bar reaches a selected

color change point, the entire bar will change to the color designated for that zone. This eliminates any

ambiguity as to the signal status, especially just after transitioning to a new zone.

First (Step Q) is to select the color to be displayed, when the bar is “below*”, whichever set point is set

to the lowest position.

Second (Steps R, S, T, and U) is to select the color to be displayed when the bar is above each specific

set point, regardless of the order or position to which the set points are set.

However, if two or more setpoints with differently specified colors are positioned at the same set point

value, the color specified for the set point with the highest identifying number will be displayed. When

set points are set to the same value, the SP4 color overrides the SP3 color, the SP3 color overrides the

SP2 color, and the SP2 color overrides the SP1 color.

STEP Q Select Bargraph Color when the bar is BELOW* the Setpoint that is set to the lowest

position