The Andersons LCO-1000 Quick setup guide

The following tools:
—7/16” and a 3/8” open-end wrench (or adjustable
wrenches)
—Phillips Head Screwdriver
—Pliers
Assembly, Use and Care
Our toll-free number is 1-800-225-2639 (U.S. Only)
Before You Begin ...
To assemble your side
deflector, we highly
recommend that you read
all the instructions thoroughly,
familiarize yourself with the
assembly and components, and
verify that all parts are included
in the package.
Model LCO-1000
You Will Need ...
Side Deflector Kit

Assembly
Remove the components from the carton. On the
RH. side of the spreader as shown, remove the
two nuts and lock washers holding the hopper onto the
frame. Install the mounting plate to the frame and
reinstall nuts and lock washers previously removed but
do not tighten. Insert the #10-24 x 1 1/2” screw into the
hole in the front of the mounting plate and frame. Secure
with a locknut supplied. Tighten all the
1)
Install the deflector plate spring into the hole in the
deflector plate. Attach the deflector plate to the
mounting bracket as shown using (2) 1/4-20 x 5/8”
hex bolts and locknuts. TIGHTEN NUTS THEN
LOOSEN NUTS JUST ENOUGH TO ALLOW THE
DEFLECTOR TO SWING FREELY. Attach the kick
plate to the deflector using (2) #10-24 x 1/2” bolts and
locknuts.
2)
On the back of the spreader, remove the (2)
plastic plugs and install the spring bracket
onto the hopper as shown using (2) #10-24 x 1/2”
screws and locknuts. Using pliers, attach the spring to
the spring bracket. *If holes are not drilled in the
hopper, use the drill guide on the last page for
correct placement.
3)
Insert the hooked end of the push/pull cable into
the hole in the auxiliary shut off plate. Slide the
auxiliary shutoff plate under the LH. side of the shutoff
plate and between the guide as shown. Auxiliary
shutoff plate should slide freely after installation.
5)
Attach the auxiliary shutoff bracket to the right
side of the upper handle using (2) #10 x 1/1/2”
Philips screws and locknuts. Apply the shutoff label
to handle positioned as shown. “CLOSED” should
be toward hopper.
4)
Slide Push/Pull Cable into notch on bracket
between the washer and hex nut. Tighten nuts
taking care not to twist the cable. Secure cable to
the leg with the wire tie.
Slide the cable clamp onto the cable positioned as
shown. Secure with a #10-24 x 3/8” screw but do
not tighten. Push the Cable Knob in and position the
cable in the clamp so the hopper hole is completely
closed. Tighten screw.
6)
7)
Mounting Plate
#10-24 x 1 1/2
Screw & Locknut
Spring
Deflector Plate
1/4-20 x 5/8 Bolt
& Locknut
#10-24 x 1/2”
Screw & Locknut
Spring
#10-24 x 1/2”
Screw & Locknut
Spring Bracket
Aux. Shutoff
Bracket
#10-24 x 1 1/2
Screw & Locknut
Position
“CLOSED” toward
hopper
Push/Pull Cable
#10-24 x 3/8”
Screw Cable Clamp
Hopper Hole
Completely Closed
Aux. Shutoff Plate Hooked End of
Push/Pull Cable
Shutoff Plate
Guide
Kick Plate

Operation
The deflector shield is used to block off the right side portion of the swath width. It should be used in the
“ON” position (down) together with the auxiliary shutoff in the closed position (done by pushing the control
knob forward). IMPORTANT: Turf products will be applied excessively at the center of the swath if
the auxiliary shutoff is not closed when the deflector is in use. Always remember to re-open the
auxiliary shutoff (by pulling the control knob back) when returning to a full swath width.
DEFLECTOR ON (DOWN) DEFLECTOR OFF (UP)
Ordering
1) Part number (DO NOT use key numbers when ordering parts. ALWAYS use part numbers.)
2) Part description
3) Side Deflector Kit (product code SDSHIELDCO)
See diagram for assistance in identifying specific parts.
For parts orders, call 1-614-559-2655. (Note: Sales of parts for the Andersons spreaders are handled by PSB Company.
IMPORTANT: When ordering replacement parts, always provide the following information:
12
345
67
8911
KEY PART DESCRIPTION PART #
1Mounting Plate P16609
2Deflector Plate P16610
3Kick Plate P15654
4Spring Bracket P16611
5Auxiliary Shutoff Plate-LH. P16612
6Control-Push/Pull P790490
7Spring P15653-1
8Fastener/Parts Package P16613
9Cable Clamp P90600
10 Aux. Shutoff Bracket P790552
11 Label-Push/Pull Control P15590
Push Control
Knob In Pull Control
Knob Out
10

Warranty
It is our first priority to improve our products’ quality
and performance whenever possible.
Your comments and questions are always welcome!
Please call our Helpline: 1-800-225-2639
(U.S. Only)
Or Visit Our Website at …
www.andersonsplantnutrient.com
The Andersons Inc.
1947 Briarfield Blvd.
Maumee, Ohio 43537
The Andersons warrants to Purchaser the following:
1. Product will be free of defects in materials and workmanship for a period of one year from date of purchase.
2. If the spreader is used for commercial rental the Limited Warranty shall be limited to a period of 90 days.
3. All Unit and part replacement will be performed at the reasonable discretion of The Andersons and EarthWay.
4. Labor charges are not covered and the unit need not be returned to the dealer for warranty service.
5. Proof of purchase must be supplied to The Andersons.
6. For warranty questions, contact EarthWay at 1-800-294-0671.
The Andersons sole obligation under this warranty is limited to repairing or replacing the defective part.
This warranty does not extend to any Product or parts thereof that have been allowed to corrode, subjected to misuse, neglect, accident, or modification
by anyone other than The Andersons or that have been affixed to any nonstandard accessory attachment or that have been used, stored, installed,
maintained operated in violation of The Andersons instructions or standard industry practice. No agent, employee or representative of The Andersons
has any authority to bind The Andersons to any affirmation, representation or warranty concerning the Product and any affirmation, representation or
warranty made by any agent, employee or representative shall not be enforceable by Purchaser.
THIS WARRANTY EXTENDS ONLY TO THE ORIGINAL PURCHASER AND IS EXPRESSLY IN LIEU OF ANY OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDING
WITHOUT LIMITATION ANY IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS OR INTENDED USE FOR A PARTICULAR PURPOSE AND OF ANY OTHER
OBLIGATION ON THE PART OF The Andersons. The Andersons SHALL NOT BE LIABLE FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL LOSS, DAMAGE OR
EXPENSE DIRECTLY OR INDIRECTLY ARISING FROM THE USE OF ANY OF THE PRODUCT INCLUDING, BUT NOT LIMITED TO, DAMAGE OR LOSS OF OTHER PROPERTY
OR EQUIPMENT, LOSS OF PROFITS OR REVENUE, COST OF CAPITAL, COST OF PURCHASED OR REPLACEMENT GOODS, OR CLAIMS OF CUSTOMERS OF
PURCHASER.

Spring Bracket
Drill Guide Template
You will need a 3/16” drill to make the hole.
Step 1. Cut the guide below on the cut line
Step 2. Position the guide to the right side and above the Pivot Bracket
Step 3. Mark the center line of each Spring Bracket hole
Step 4. Drill the holes for the Spring Bracket
Step 5. Mount the Spring Bracket as directed on page 2, #3.