The Handy THLS-6G Manual

ADDED INFORMATION SHEET - THLS-6G & 4G LOG GUARD
Guard Bottom Plate
1. Mount the guard bottom plate to the rear guiding plate and secure with two M6×12 screws and locknuts
with a 5mm Allen Key and 10mm Spanner. Ensure the triangular longside sits against the cut away of the
rear guiding plate.
2. Loosen the socket head cap screw and big washer on the wheel bracket with a 5mm Allen Key, insert the
open end of support strut B between the big washer and wheel bracket and tighten screw with 5mm Allen
Key.
Triangular Longside
Rear Guiding Plate
Socket Head Cap Screw
Support Strut B
Open End of
Support Strut

3. Connect the upper end of support strut B to the guard bottom plate with cross head screw M6×12 and
locknut M6 and then tighten with Phillips Screwdriver and 10mm Spanner.
Log Tray A
1. Remove the Allen Key screw M6x12 with spring washer from the log splitter body, using 5mm Allen Key.
Support Strut B

2. Align the mounting hole of the log tray A to the hole in the log splitter body and refit the M6x12 Allen Key
screw with spring washer 6, using a 5mm Allen Key.
3. The right side of Log Tray A, is secured using Allen Key screw M16×12 and locknut M6 on to the rear
guiding plate and secure with 5mm Allen Key and 10mm Spanner.
4. Loosen the cup head bolt and nut using 12mm Spanner on left side of the front leg and insert the open
end of support strut A onto the bolt and then tighten the nut.
Support Strut A
Log Tray A
Front Leg Cup Head
Bolt

5. Connect the upper end of support strut A to log tray A with cross head screw M6×12 and locknut M6 and
then tighten with Phillips Screwdriver and 10mm Spanner.
Log Tray B
Now rotate the machine 180odegrees.
1. Remove the Allen Key screw M6x12 with spring washer from the log splitter body, using 5mm Allen Key.

2. Align the two mounting holes of the log tray B to the holes on the side of the splitter. Insert one socket
head cap screw M6×12 and spring washer 6 back into the mounting hole, using 5mm Allen Key.
3. Insert Allen Key screw M6×12 and locknut M6 through the Log Tray B and Rear Guiding Plate and tighten
using 5mm Allen Key and 10mm Spanner.
4. Loosen the cup head bolt and nut on the front leg, insert the open end of support strut A onto the bolt
and then tighten the nut using 12mm Spanner.

5. Connect the upper end of support strut A to the log tray B with cross head screw M6×12 and locknut M6
and then tighten with Phillips Screwdriver and 10mm Spanner.
6. Secure Log Tray A to Log Tray B, using the two cross head screw M6×12 and locknut M6 and then tighten
with Phillips Screwdriver and 10mm Spanner.

Steel Guard
1. Attach the front guard plate to the logsplitter, using a M6x12 bolt and locknut. It is secured within the
Control Lever Guard and tighten with Phillips Screwdriver and 10mm Spanner.

2. Align the holes of the guard side plates with the fitted trays and secure using M5x12 bolts and locking nuts
using Phillips Screwdriver and 8mm Spanner.

3. Secure the two guard side plates together with the four hole, silver bracket and secure with cross head
M5x12 screws and M5 locknuts and tighten with 5mm Allen Key and 8mm Spanner.

4. Attach the single guard side plate to fitted log trays on the working side of the logsplitter, using M5x12
screws and M5 locknuts and tighten with 5mm Allen Key and 8mm Spanner.
5. Now add the top guard plates, starting with the smaller plate, which sits above the working area. Secure it
to the front guard plate and the rear of the two side guard plates, using using M5x12 screws and M5
locknuts and tighten with 5mm Allen Key and 8mm Spanner in the holes provided.

6. Now you can secure the large top plate to the two side guard plates, using M5x12 screws and M5 locknuts
and tighten with 5mm Allen Key and 8mm Spanner in the holes provided.
7. The final step is to secure both top guards to one another, using the supplied silver plate and secure with
M5x12 screws and M5 locknuts and tighten with 5mm Allen Key and 8mm Spanner in the holes provided.
Your logsplitter is now ready for you to follow the operation instructions, within the manual supplied with the
machine.