The Singing Machine SMM-112 User manual

SMM-112
Instruction Manual
PROFESSIONAL WIRELESS
MICROPHONE
Please read before using this unit.

1
Contents
1. Headset Wireless Microphone x 1
2. Microphone Receiver x 1
3. Microphone Transmitter x 1
Congratulations on your purchase of a Singing Machine Wireless
Microphone. We at the Singing Machine know that it will provide you and
your friends with endless hours of entertainment. Inside you will find
instructions on how to use and maintain this unit.
Microphone Transmitter Details
Settings
The switch on the transmitter of your Singing Machine Wireless
Microphone has three settings:
1. ON - The switch is set to ON position. The microphone will function. The
red indicator light is on. The transmitter will use battery power.
2. STANDBY - The switch is set to STANDBY position. The microphone will
not function. The red indicator light is on. The transmitter will
use battery power.
NOTE: The purpose of this setting is to maintain a connection between the
microphone and the receiver when moving around the area in
which it is being used.
3. OFF - The switch is set to OFF position. The microphone will not function.
The red indicator light is off. The transmitter will not use battery
power.
Important Note: When the microphone transmitter switch is set to OFF,
noise may be generated from the karaoke machine. Please make sure to
reduce both the MASTER VOLUME and MIC VOLUME to the low level OR
switch off the receiver before turning off your microphone.
1 2 3

2
Instructions for Use
1. Insert one (1) active DC 9-Volt battery into the slot located at the
bottom of the transmitter.
2. Insert one (1) active DC 9-Volt battery into the slot located in the back
of the receiver.
3. Plug the 3.5mm microphone cord into the transmitter input jack.
4. Hold the transmitter on the belt by attached clip.
5. Properly wear the wireless headset microphone and adjust the mic
head by its flexible cord to appropriate position.
6. Set the switch on the transmitter to the STANDBY position.
7. Plug the receiver into the Microphone Input Jack of your Singing
Machine karaoke machine.
8. Set the switch on your Singing Machine karaoke machine to the ON
position.
9. Adjust the Master Volume and Mic Volume Controls of your Singing
Machine to a comfortable level.
10. Set the switch on the receiver to the ON position.
11. Set the switch on the transmitter to the ON position.
Your Singing Machine Wireless Microphone is now ready for use!
Maintenance
!To ensure long battery life, please make sure that both the Receiver and
the Transmitter are set to the OFF position when not in use. To be
absolutely certain, we advise you to remove the 9-Volt batteries from
both the Receiver and the Transmitter when they are not in use.
!Please remove the Receiver from the Microphone Input Jack of your
Singing Machine karaoke machine when not in use. This will reduce the
possibility of damage to the Receiver.
Æ

3
1.PROBLEM: The Transmitter indicator light is on, but there is no sound
when I sing.
a) Is the Transmitter switch set to ON?
b) Have you plugged your headset microphone into the transmitter input
jack?
c) Is the Singing Machine karaoke machine correctly plugged in and
switched on?
d) Are the Microphone Volume and Master Volume controls of your Singing
Machine set to a high enough level?
e) Does the Receiver contain one (1) 9-volt battery,is it properly connected
to your Singing Machine, and is it turned on?
2.PROBLEM: The Receiver indicator light is on, but there is no sound when
I sing.
a) Is the Receiver properly connected to your Singing Machine?
b) Is the Transmitter switch set to ON?
c) Have you plugged your headset microphone into the transmitter input
jack?
d) Does the Transmitter contain one (1) 9-volt battery?
e) Is the Singing Machine karaoke machine correctly plugged in and
switched on?
f) Are the Microphone Volume and Master Volume controls of your Singing
Machine set to a high enough level?
3.PROBLEM: The Singing Machine karaoke machine I am using is
switched on, but there is no sound when I sing.
a) Is the Transmitter switch set to ON?
Troubleshooting

4
Troubleshooting
b) Have you plugged your headset microphone into the transmitter input
jack?
c) Does the Transmitter contain one (1) 9-volt battery?
d) Are the Microphone Volume and Master Volume controls of your Singing
Machine set to a high enough level?
e) Does the Receiver contain one (1) 9-volt battery,is it properly connected
to your Singing Machine, and is it turned on?
CAUTION: Two of same microphones should not be used in same location
unless with one wireless and one wired microphone.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
The term IC: before the radio certification number only signifies that
Industry Canada technical specifications were met.
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
""
Wireless Microphone Information

Warning: Modifying, tampering and adjustment to this unit or
replacement of any transmitter component (crystal, semiconductor,
etc.) to this unit that could result in a violation of the rules.
FCC NOTICE
This wireless microphone system complies with Part 90 of FCC Rules.
There is one frequency available for the system. You must get a licence for
the frequency you plan to use before you use the system.
Please look for this website http://wireless.fcc.gov/uls/ to apply the licence
or phone to the nearest FCC offices and contact them to get the necessary
application. Licensibility depends on how you will use the system.
FOR RF EXPOSURE
“IMPORTANT NOTE: To comply with the FCC RF exposure compliance
requirements, no change to the antenna or the device is permitted. Any
change to the antenna or the device could result in the system exceeding
the RF exposure requirements.”
SAFETY INFORMATION
Your wireless microphone contains a low power transmitter. When the EUT
is power on and it sends out radio frequency (RF) signals. In August 1996,
the Federal Communications Commissions (FCC) adopted RF exposure
guidelines with safety levels for wireless devices.
IMPORTANT
To maintain compliance with the FCC's RF exposure guidelines hold the
transmitter and antenna at least 1 inch (2.5 centimetres) from your face and
speak in a normal voice, with the antenna pointed up and away from the
face. Ensure that the antenna is at least 1 inch (2.5 centimetres) from your
body when you using your wireless microphone.
Use only the supplied antenna. Unauthorised antennas, modifications, or
attachments could damage the transmitter and may violate FCC
regulations.
Wireless Microphone Information
5

Specifications
TYPE
-64 dB 600 OHMS IMPENDANCE
UNI-DIRECTIONAL DYNAMIC
MICROPHONE
POWER SOURCE 9V Battery x 2 (Not included)
MICROPHONE DIMENSION 5.5 x 13.0 x 18.0 cm
2.2 x 5.1 x 7.1 Inches
TRANSMITTER DIMENSION 7.7 x 6.2 x 2.7 cm
3.0 x 2.4 x 1.1 Inches
RECEIVER DIMENSION 7.3 x 10.0 x 2.6 cm
2.8 x 3.9 x 1.0 Inches
6

PRINTED IN CHINA
The Singing Machine Company, Inc.
6601 Lyons Road, Bldg. A7, Coconut Creek, FL33073-9902, USA.
TEL: [phone] FAX: [phone]
VISIT OUR WEBSITE www.singingmachine.com
112-0411-ENG01