Thermador T24UR820DS User manual

Page | 1
Model/Modele/Modelo
T24UR820DS
T24UR810DS
T24UR800DP
Double Drawer Refrigerator
Réfrigérateur à double tiroir
Refrigerador de doble cajón
INSTALLATION
GUIDE
GUIDE
D'INSTALLATION
GUIA DE
INSTALACION

Page | 2
3
4
4
9
9
11
15
5
19
20
IMPORTANT:
Before you begin, read these instructions completely and
carefully.
INSTALLER:
Please leave this manual with owner for future reference.
OWNER:
Save these installation instructions for local electrical
inspector’s use and for future reference.
Table of Contents
Introduction ………………………………….
- Inspect the Refrigerator
Tools needed for installation ……………..
Materials supplied …………….………….…
Installing the appliance …………………….
- Transporting
- General measures
- Installation location
- Installing side-by-side
Ventilation …………………………………….
Connecting the appliance …………………
- Electrical connections
Installing the anti-tip-bracket ……………..
Installing the overlay panel ………………..
Customer Service Information ……………
Addendum A ……………………………….…

Page | 3
Introduction
These installation instructions are intended for use by qualified installers.
In addition to these instructions, the appliance shall be installed:
xIn the United States, in accordance with the
National Electric Code/State and municipal
codes and/or local codes.
xIn Canada, in accordance with the Canadian
Electric Code C22.1 –latest edition/Provincial
and Municipal codes and/ or local codes.
Please read these installation instructions completely and carefully.
They will save you time and effort and help to ensure optimum performance.
Be sure to observe all listed warnings and cautions.
Look for the triangles with exclamation marks inside.
WARNING:
This indicates that death or serious
injury may result due to non-observance
of this warning.
CAUTION:
This indicates that minor or moderately
severe injury may result due to non-
observance of this warning.
Important
xNEW INSTALLATION –If the appliance is a new installation, most of the work must be
done before the unit is moved into place.
xREPLACEMENT –If the appliance is replacing another appliance, the connections for
the appliance being replaced must be checked for compatibility with the new unit and
replaced as necessary.
Inspect the Refrigerator
Remove all tape, packaging and plastic covers.
After unpacking the appliance and prior to installation, thoroughly inspect the Refrigerator for possible
freight or cosmetic damage. Report any damage immediately.
NOTE: Please do not discard any bags or items that come with the original package until after the entire
installation has been completed!

Page | 4
Installation Kit
Long Screws: 4 pieces
Short Screws: 16 pieces
Left Hook: 4 pieces
Right Hook: 4 pieces
ONLY FOR T24UR800DP MODELS.
Anti-tip-bracket. 2 pieces.
Screws: 2 pieces.
1 Insulating Foam
(Not illustrated)
20 1/2”
(520mm) x 29 1/8”
(740mm) x 1/8” (3mm)
Tools needed for installation
Tape Measure Philips Screwdriver Level
These are the tools that you may need for the installation of the appliance. However, if you need to
modify the counter or cabinetry to fit the unit, you may need other tools to make counter/cabinetry
modifications before installing the appliance.
Materials supplied

Page | 5
Installing the appliance
Most of the installation work must be done before the Refrigerator is moved into place.
Have a technician install and connect the appliance according to the enclosed installation instructions.
WARNING:
Do not install this appliance:
- Outdoors
- In an environment with dripping water
- In rooms where there is a risk of frost
Transporting
The appliance is heavy and must be handled with caution during transportation and installation.
Because of the weight and dimensions of the appliance, at least two persons are necessary to move the
appliance into position securely and avoid injuries to people or damage to the appliance.
General measures

Page | 6
Installation location
A dry, well ventilated room is suitable as an installation location. The installation location should not be
exposed to direct sunlight and not placed near a heat source, e.g. a cooker, radiator, etc.
If installation next to a heat source is unavoidable, use a suitable insulating plate or observe the following
minimum distance from the heat source:
To electric or gas oven/range 1¼” (3 cm).
To an oil or coal-fired cooker 1113/16” (30cm).
To another Refrigerator or Wine Reserve 1” (2.54cm)
The floor of the installation location must not give way; if necessary, reinforce floor. The appliance must
be upright to function correctly.
For proper operation and appearance of the unit, the cabinet opening should be square and have
dimensions as shown in the next diagrams
TOP VIEW
FRONTAL VIEW
864-889mm
34” – 35”
611mm
24 1/16”
Counter opening
915mm
36”
25.4mm
1”
*24”
(610mm)
Counter opening
14mm
1/2”
(MINIMUM)
610mm
24”
Unit
624mm
24 9/16”
Counter
23 7/8”
607mm
Unit

Page | 7
Installing Side-by-Side
The appliance can be installed beside another Thermador appliance. Follow the next dimensions and
notes for the correct installation of the appliance in a side-by-side layout.
NOTE: Before placing the unit into the niche, adhere the Insulating Foam (included with the product) on
the side of the unit that will be placed next to the additional appliance. Be sure that the Insulating Foam is
even with the surface of the unit and that there are no bubbles or bumps on the Insulation Foam after
adhering it to the unit.
Two Double Drawer Refrigerators side-by-side.
Side of the unit next to
the other appliance.
Insulating Foam
Included with the unit.
1224mm
48 3/16”
607mm
23 7/8”
607mm
23 7/8”
13mm
1/2”
(MINIMUM)

Page | 8
1224mm
48 3/16””
607mm
23 7/8”
607mm
23 7/8”
13mm
1/2”
(MINIMUM)
90°
Doors could hit each other.
One Double Drawer and one swing door appliance: opening of the door should be opposite to the
Double Drawer to avoid interference or damage by hitting.
Do not place a swing door appliance with the opening of the door right beside the Double Drawer.
The drawers and the door may impact each other damaging the units.
90°
!
1224mm
48 3/16”
607mm
23 7/8”
607mm
23 7/8”
13mm
1/2”
(MINIMUM)
Opposite to Drawer
90°

Page | 9
Ventilation
The Refrigerator unit is ventilated only at the Toe-Kick in the base. Never cover that area or place
anything in front of it. Otherwise the refrigeration cooling performance will be affected and the unit must
work harder increasing power consumption.
Additionally, make certain all 4 leveling legs are extended (unit height approximately 34½”), so that
there is sufficient airflow underneath the appliance.
Connecting the appliance
After installing the appliance, wait at least 1 hour to turn on the appliance. During transportation the oil
in the compressor may have flowed into the refrigeration system.
Before switching ON the appliance for the first time, clean the interior of the appliance (see chapter
“Cleaning the appliance”in the Use & Care Guide).
Electrical connection
WARNING:
These installation instructions are intended for use by qualified installers.
WARNING:
Avoid the risk of an electric shock!
Insert into a grounded receptacle.
Never remove grounding phase.
Do not use any adapters.
Do not use any extension cords.
WARNING:
It is the customer’s responsibility to insure that the appliance installation is in compliance with all national
and local electrical codes and ordinances. Non-compliance with these instructions may result in death,
fire or an electric shock.
All legs are adjustable by up to ½ inch.

Page | 10
The receptacle must be near the appliance, 61” (1550mm) to the right of the appliance or 37” (940mm)
to the left of the appliance, and also freely accessible following installation of the appliance for future
service.
The appliance complies with protection class I. Connect the appliance to 115 V/ 60Hz alternating
current via a correctly installed receptacle with grounded terminal.
The appliance comes with a UL registered 3-wire power cord NEMA 5-15p type. The appliance
requires a 3-pole receptacle.
WARNING:
Never connect the appliance to electronic energy saver plugs.
This appliance can be used with mains and sine-controlled inverters. Main controlled inverters are used
for photovoltaic systems which are connected directly to the national grid.
Sine-controlled inverters must be used for isolated applications (e.g. on ships or in mountain lodges)
which are not connected directly to the national grid.
The appliance requires a 3-pole socket. The socket should be connected by an electrician only.
Where there is a 2-pole standard wall socket, it is the responsibility of the customer to have this socket
replaced with a correctly grounded 3-pole wall socket. Do not use any adapter plugs.
Be sure that the location of your Wine Cellar has a near and accessible electric socket.
2-pole standard wall socket must be replaced with a 3-pole grounded socket. Do not use adapters.
Never remove the grounding phase