thermastor Santa-Fe Advance User manual

© 2007 Therma-Stor LLC •Manual P/N TS-383 8/07
For small usage:
P.O. Box 8680 Madison, WI 53708 •TOLL-FREE 1-800-533-7533 •www.thermastor.com •[e-mail]
Designed For Crawlspace Dehumidification
INSTALLER’S & OWNER’S MANUAL
HVAC INSTALLER: PLEASE LEAVE MANUAL FOR HOMEOWNER

SANTA FE ADVANCE INSTALLER'S AND OWNER'S MANUAL
2Santa Fe Advance Installer’s & Owner’s Manual 3Santa Fe Advance Installer’s & Owner’s Manual
Table of Contents
Precautions ...............................................................................1
1. Intended Application ..............................................................2
2. Registrations .........................................................................2
3. Specifications ........................................................................3
4. Unit Assembly ........................................................................3
4.1 Installing Feet ......................................................................3
4.2 Attaching Drain Hose ...........................................................3
5. Installation .............................................................................3
5.1 Location ..............................................................................3
5.2 Electrical Requirements .......................................................4
5.3 Condensate (Water) Removal ...............................................4
6. Operation ...............................................................................4
6.1 Humidity Control Adjustment ...............................................4
6.2 Defrost Cycle .......................................................................4
6.3 Blower (Fan) Switch .............................................................4
7. Maintenance ..........................................................................5
7.1 Air Filter ...............................................................................5
7.2 Cleaning and Replacement ..................................................5
7.3 Removing Filters ..................................................................5
7.4 Installing Filters ...................................................................5
8. Service ..................................................................................5
8.1 Technical Description ...........................................................5
8.2 Troubleshooting ...................................................................6
9. Accessory/Replacement Parts ................................................6
Remote Humidity Control........................................................ 7-9
Condensate Pump Kit ...............................................................10
8 Inch Collar Assembly .............................................................11
Duct Kit Assembly.....................................................................12
Warranty ..................................................................................13
Precautions
• Do not operate the unit with a cut or frayed power cord.
• Do not unplug the unit by pulling on the cord. Grasp the plug
firmly and pull it out of the wall socket or power receptacle.
• Always use a grounded outlet.
• Never operate electrical equipment near or in standing water.
• Do not stick your fingers or other objects through the safety grills.
• Do not restrict airflow into or out of the unit. This may cause the
unit to overheat.
• Unit should never be serviced or cleaned while it is plugged in.
• Do not sit or stand on the unit or use as a shelf or table.
• Before leaving the Santa Fe Advance unattended, ensure children
do not have access to the equipment. Do not allow children to
play with or near the unit or in its air flow.
• The Santa Fe Advance is designed to be installed indoors only.
Read the installation, operation and maintenance instructions
carefully before installing and using this unit. Proper adherence to
these instructions is essential to obtain maximum benefit from your
Santa F.e dehumidifier.
Read and Save These Instructions
WARNING! — Indicates the possibility of death or
serious injury.
IMPORTANT! — Indicates the possibility of injury
or damage to property only.
1. Intended Application
The Santa Fe Advance is intended for installation in crawl spaces
or basements that experience short or long-term high humidity
conditions; however, the attractively designed unit can be placed
in almost any residential setting where dehumidification is desired.
Use in non-residential applications and pool areas will void
warranty.
The Santa Fe Advance is designed to operate in temperatures
between 56° and 95°F. Temperatures outside of these ranges may
affect dehumidifier performance.
In order to efficiently control the humidity levels, the area in which
the dehumidifier is to be placed must be free of water intrusion or
excessive fresh (outside) air infiltration. Before installing the Santa
Fe Advance, water intrusion and air infiltration problems should be
addressed.
2. Registration
The Santa Fe Advance conforms to UL STD 474 and CSA standard
C22.2 No. 92
3. Specifications
Model: Santa Fe Advance (P/N 4025699)
Electrical: 110-120 VAC, 6.35 Amps @ 80°F, 60% RH,
60 Hz, grounded
Capacity: 90 pints/day @ 80°F, 60% RH
Operating Temp: Between 56°F and 95°F Max
Air Flow: 240 CFM without external restriction
Refrigerant Charge: 1 lb, 8 oz R22
Unit Size: 33” L x 141/2” W x 19” H
Shipping Size: 39” L x 22” W x 25” H
Unit Weight: 71 lbs
Shipping Weight: 78.5 lbs

SANTA FE ADVANCE INSTALLER'S AND OWNER'S MANUAL
2Santa Fe Advance Installer’s & Owner’s Manual 3Santa Fe Advance Installer’s & Owner’s Manual
4. Unit Assembly
4.1 Installing Feet (Optional)
Included with your Santa Fe
Advance are four leveling feet. It
is important to level the unit for
proper draining. (See section
5.1.4, Figure 6)
Installing Leveling Feet
See Figures 2 and 2a for installing leveling feet.
1. Lay down a protective pad (pillow, blanket, etc.).
2. Carefully turn unit onto side opposite filter opening and drain
port.
3. Align leveling foot shaft with one of the four threaded hole
locations as shown in Figure 2.
4. Screw each leveling foot in ten revolutions.
5. Carefully bring unit to upright position.
6. Level unit for proper drainage as described in section 5.1.4
(Figure 6) of this manual.
7. Wait 10 minutes before operating.
IMPORTANT!
Note: Operating the unit immediately after bringing it to an upright
position can possibly damage the compressor. A short amount
of time is needed to allow the oil to return to it’s reservoir for
lubrication.
4.2 Drain Hose
Take drain hose off of drain port. With scissors, cut one inch off of
hose end to eliminate dented area. Place drain hose end on drain
port until fully seated. Refer to Section 5.1.4 regarding proper
drainage.
5. Installation
5.1 Location
The Santa Fe Advance can be installed in a variety oflocations to
meet the owner’s needs, but should beinstalled directly in the area
to be dehumidified. Other considerations include:
1. Providing access to a 115 VAC power outlet (10’ power cord
is provided).
2. Locating near a floor or other suitable drain (8’ drain hose
included).
3. Do not install the Santa Fe Advance with the intake or
exhaust of the unit within 1’ of a wall or other obstruction.
Do not place the unit where curtains or debris can be
drawn onto the intake and restrict airflow. Do not operate in
standing water or place the unit near open water. Refer to
Figure 5.
4. The Santa Fe Advance drains via a gravity system. A level
indicator has been included near the intake of the unit.
To ensure the unit will drain properly, the unit should be
positioned so the level bubble appears in the non-shaded
area of the level indicator as shown. Refer to Figure 6. If
the unit is placed on an unlevel surface, adjust leveling feet
using a crescent wrench or 7/16” open wrench. Move handle
end of wrench from left to right to lower one foot. Adjust all
four feet underneath the unit until bubble in the level dial is
in the correct position. Failure to level the unit may result
in leakage or improper drainage. See Section 4.2 regarding
drain hose installation.
Figure 2: Insert leveling feet in
locations
Figure 2a: Screw each leveling
foot in ten revolutions
Figure 1: Four leveling feet
Figure 3: Drain port Figure 2a: Drain hose position
Figure 5: Installing Santa Fe Advance in area with proper clearance.
Figure 6: Level bubble should be in indicator area for proper drainage.

SANTA FE ADVANCE INSTALLER'S AND OWNER'S MANUAL
4Santa Fe Advance Installer’s & Owner’s Manual
5.2 Electrical Requirements
The Santa Fe Advance plugs into a common grounded outlet on a
15-Amp circuit. While operating, it draws less than 7 amps @ 80°F,
60% RH and less than 6 amps @ 75°F, 50% RH. Use of a ground
fault circuit interrupter (GFCI) protected circuit is recommended.
The unit should not be used in areas prone to flooding.
5.3 Condensate (Water) Removal
The Santa Fe Advance drains via a gravity system - it is not able
to push condensate (water) uphill. The drain hose must run flat or
downhill toward the drain location. Be sure the hose is not kinked
or otherwise restricted so that water can pass through it. Improper
hose installation may result in water leakage.
To increase the efficiency of the unit, position the hose to create a
“trap” as shown in Figure 8. By creating a trap, it will hold a small
amount of water. Position the trap on the hose approximately 12’’
- 20’’ away from the unit. Check hose regularly to ensure it is clear
and water is draining properly.
If floor drain is not easily accessible, a condensate pump kit with a
20’ hose is available. Refer to page 5 for ordering accessories.
6. Operation
6.1 Humidity Control Adjustment
The humidity control is an adjustable switch that turns the
dehumidifier on and off. It turns on when the relative humidity of
the air in which it is located rises to the dial set point. It turns off
when the RH drops 5% below the set point.
Approximate Humidity Levels Per Setting
“Dry” 35% to 45% Relative Humidity
“Normal” 45% to 55% Relative Humidity
(Recommended for most applications)
“Humid” 55% to 65% Relative Humidity
The dehumidifier will run continuously until the relative humidity
(RH) is reduced to the humidity control dial setting. There is no
benefit to setting the humidity control to “dry” in rooms under 65°;
doing so will result in long periods of ineffective dehumidifier run
time.
Quality humidity meters are available from Therma-Stor and are
recommended to accurately monitor humidity levels. Please call
1-800-533-7533 to order.
Once the dial has been set to the desired level of humidity control,
the Santa Fe Advance will maintain the same percentage of relative
humidity regardless of room temperature.
To turn the unit off, position the humidity dial to the far left and set
fan control to “auto.”
6.2 Defrost Cycle
An automatic defrost thermostat is attached to the refrigerant
tubes inside the unit. It will automatically shut the compressor
off if excessive frost forms on the evaporator coil. The blower
will continue to run, causing air to flow through the evaporator
coil and melt the ice. When the ice has melted, the evaporator
temperature will rise and the thermostat will automatically restart
the compressor. During this process, cool air may be coming out of
the unit.
6.3 Electrical Requirements
Turning the fan switch “FAN ON” will
cause the unit’s internal blower to
run continuously, whether the unit is
dehumidifying or not. This function
is desirable if the unit is used for air
circulation or filtration. Turning the fan
switch to “FAN AUTO” will cause the unit’s
internal blower to run only while the unit is dehumidifying.
FAN
ON
FAN
AUTO

SANTA FE ADVANCE INSTALLER'S AND OWNER'S MANUAL
5Santa Fe Advance Installer’s & Owner’s Manual
7. Maintenance
IMPORTANT!
NOTE: Do not operate the unit without the proper filter or with
a less effective filter. The heat exchange coils inside the unit
could become clogged, resulting in a loss of effectiveness
and/or efficiency and may require disassembly to clean.
7.1 Air Filter
The Santa Fe Advance ships with a standard MERV-11 65%
1” pleated fabric filter and a 1/4” aluminum framed pre-filter
installed. Operating the unit with a dirty or obstructed filter will
reduce dehumidifier capacity and efficiency and may cause the
compressor to cycle on and off unnecessarily.
7.2 Cleaning & Replacement
Check filters every six months. Clean and/or replace when filters are
visibly dirty. See cleaning instructions below. Replacement filters can
be ordered from Therma-Stor by calling 1-800-533-7533.
The 1/4” washable pre-filter
should not to be discarded.
Inspect the pre-filter for debris,
dirt, or other obstructions at
the same time the 1” pleated
fabric filter is checked. Wash the
1/4” pre-filter every time the 1”
pleated fabric filter is replaced. To
clean the 1/4” pre-filter, remove
filter from the unit, rinse the 1/4”
pre-filter in water with the water
flowing through the aluminum
support mesh side. Refer to
Figure 11. Allow the filter to dry
completely before reinstalling.
Reinstall the filters per the
instructions below or on the tag
located on the 1/4” pre-filter.
IMPORTANT!
NOTE: Failure to follow filter handling instructions may result
in improper function of the dehumidifier and cause premature
filter wear.
7.3 Remove Filters
1. Gently remove the 1/4” pre-filter by pulling on the tab
attached to the filter.
2. Gently remove the 1” pleated fabric filter by pulling it out
of the unit.
7.4 Installing Filters
1. Gently slide 1” pleated filter into filter slot. Do not force.
If resistance is felt, check alignment for obstructions or
debris inside the filter housing.
2. Gently slide 1/4” pre-filter to left of 1” pleated filter.
Do not force. If resistance is felt, check alignment for
obstructions or debris inside the filter housing.
8. Service
WARNING!
Servicing the Santa Fe Advance with its high pressure refrigerant
system and high voltage circuitrypresents a health hazard which
could result in death, serious bodily injury, and/or property
damage. Only qualified service people should service this unit.
8.1 Technical Description
The Santa Fe Advance uses a refrigeration system similar to an air
conditioner’s to remove heat and moisture from incoming air and
add heat to the air that is discharged. Hot, high pressure refrigerant
gas is routed from the compressor to the condenser coil. The
Figure 13: Santa Fe Advance refrigeration system.
Figure 14: Wiring diagram.

SANTA FE ADVANCE INSTALLER'S AND OWNER'S MANUAL
6Santa Fe Advance Installer’s & Owner’s Manual
refrigerant is cooled and condensed by giving up its heat to the
air that is discharged from the dehumidifier. The refrigerant liquid
then passes through capillary tubing which cause the refrigerant
pressure and temperature to drop. It next enters the evaporator coil
where it absorbs heat from the incoming air and evaporates.
The evaporator operates in a flooded condition, which means
that all the evaporator tubes contain liquid refrigerant during
normal operation. A flooded evaporator should maintain constant
pressure and temperature across the entire coil, from inlet to outlet.
The mixture of gas and liquid refrigerant enter the accumulator
after leaving the evaporator coil. The accumulator prevents any
liquid refrigerant from reaching the compressor. The compressor
evacuates the cool refrigerant gas from the accumulator and
compresses it to a high pressure and temperature gas to repeat the
process.
8.2 Troubleshooting
No dehumidification. Neither blower, nor compressor run with fan
switch AUTO.
1 Unit unplugged or no power to outlet, circuit breaker
tripped.
2 Humidity control set to “Humid” setting.
3 Loose connection in internal wiring.
4 Humidity control is defective.
No dehumidification. Compressor does not run but blower runs
with fan switch AUTO and humidity control turned to ON.
1 Defrost thermostat open, ambient temperature too low.
2 Loose connection in compressor circuit.
3 Defective compressor overload.
4 Defective compressor or compressor run capacitor.
Blower runs with fan switch AUTO but compressor
cycles on & off.
1 Low ambient temperature and/or humidity causing unit
to cycle through defrost mode.
2 Defrost thermostat defective.
3 Defective compressor overload.
4 Defective compressor.
Blower does not run with fan switch in either position.
Compressor runs briefly but cycles on and off.
1 Loose connection in blower circuit.
2 Obstruction prevents impeller rotation.
3 Defective blower.
4 Defective blower switch.
Evaporator coil frosted continuously, low dehumidifying capacity.
1 Dirty air filter or air flow restricted.
2 Defrost thermostat loose or defective.
3 Low refrigerant charge.
If none of the above has fixed the issue, call the service department
at 1-800-533-7533.
9. Accessory/Replacement Parts
4025568 Pleated Air Filter .88” x 11.75” x 11.75”
4025831 Pre-Filter
4021495 Control Knob
4025577 Hose, PVC, Clear, .625” diameter, 8’ long
4025741 Thermostat, Defrost Control
4026450 Leveling Feet
4026607 Casters Kit
4025571 Level Vial
4025322 Humidity Meter
4025569 Adapter, .625” Hose x .75” MNPT

PREPARING THE SANTA FE ADVANCE FOR REMOTE HUMIDITY CONTROLLER
7Santa Fe Advance Installer’s & Owner’s Manual
Step 1. Remove pre-filter and primary filter.
Step 2. Remove all eight (8) #10-32 screws with a
Phillips head screw driver. These are located around the
perimeter of the top cover.
Step 3. Remove two (2) #10-24 screws from the control
plate using a Phillips head screw driver.
Step 4. Removed humidity control switch knob.
Step 5. Remove control plate and top cover from
dehumidifier. Set aside.
Step 6. Remove two (2) #8 screw from the electrical box.
These screws hold the humidity control switch in place.
Preparing Dehumidifier for Remote Humidity Controller
The following instructions detail the dehumidifier disassembly, removal of high voltage controls, designation of high voltage wiring, and dehumidifier
reassembly.
WARNING! THESE OPERATIONS SHOULD ONLY BE CONDUCTED BY A LICENSED ELECTRICIAN!
THE CONTROL THAT WILL BE INSTALLED MUST BE ABLE TO SWITCH/OPERATE AT 115 VAC! ALL
ELECTRICAL CONNECTIONS SHOULD FOLLOW THE NEC REGULATIONS!

PREPARING THE SANTA FE ADVANCE FOR REMOTE HUMIDITY CONTROLLER
Step 7. Remove the electrical box assembly from the
styrofoam case. Electrical box is taped to Styrofoam.
You may need to pull firmly. Do not lean, pry, or press
anywhere on the Styrofoam case! You may damage the
Styrofoam case.
Step 8. Turn electrical box over and twist two (2) locking
tabs. Align the locking tabs with the rectangular slots.
Step 9. Partially open the box by hand. Do not bend any
further than shown.
Step 10. Remove humidity control switch from the
electrical box.
Step 11. Remove orange/black wires and blue wire
from humidity control switch.
Step 12. Electrical connections should be conducted
by a licensed electrician and all electrical connections
should follow the NEC regulations. Connect new
controller power wires to orange/black wires and
blue wire, as shown in above diagram. New controller
must be able to handle 115 VAC switched. Ensure any
connections are housed in the electrical box.
8Santa Fe Advance Installer’s & Owner’s Manual
115 VAC, 60 Hz, SINGLE PHASE
BLK
BLK WHT
WHT
GRN
GRN
YEL
RED
FAN SWITCH
DEFROST
THERMOSTAT
FAN MOTOR
COMPRESSOR
3
1
2
BLK BLK
BLU ORG
S
CR
GRN
FAN ON
FAN AUTO
DEHUMIDISTAT
RUN
CAPACITOR
115 VAC, 60 Hz, SINGLE PHASE
BLK
BLK WHT
WHT
GRN
GRN
YEL
RED
FAN SWITCH
DEFROST
THERMOSTAT
FAN MOTOR
COMPRESSOR
3
1
2
BLK BLK
BLU ORG
S
CR
GRN
FAN ON
FAN AUTO
NEW CONTROL
RUN
CAPACITOR
Wiring Before Changes Wiring After Changes

PREPARING THE SANTA FE ADVANCE FOR REMOTE HUMIDITY CONTROLLER
9Santa Fe Advance Installer’s & Owner’s Manual
Step 13. Bend rear flange of electrical box.Twist locking
tabs to close box.
Step 14. Place electrical box back on Styrofoam
part. 7/8” diameter hole can be used for strain relief.
Make sure that all electrical connections are inside the
electrical box.
Step 15. Place top cover back on the dehumidifier.
Install front cover plate with the same screws removed
in step 3. Be careful not to over torque the screws.
Step 16. Hand start the top cover screws. Use same
screws removed in step 2. Use a Phillips head screw
driver to tighten. Be careful not to over torque the
screws.
Step 17. Slide in primary filter and pre-filter.
115 VAC, 60 Hz, SINGLE PHASE
BLK
BLK WHT
WHT
GRN
GRN
YEL
RED
FAN SWITCH
DEFROST
THERMOSTAT
FAN MOTOR
COMPRESSOR
3
1
2
BLK BLK
BLU ORG
S
CR
GRN
FAN ON
FAN AUTO
DEHUMIDISTAT
RUN
CAPACITOR
115 VAC, 60 Hz, SINGLE PHASE
BLK
BLK WHT
WHT
GRN
GRN
YEL
RED
FAN SWITCH
DEFROST
THERMOSTAT
FAN MOTOR
COMPRESSOR
3
1
2
BLK BLK
BLU ORG
S
CR
GRN
FAN ON
FAN AUTO
NEW CONTROL
RUN
CAPACITOR
Wiring Before Changes Wiring After Changes

10 Santa Fe Advance Installer’s & Owner’s Manual
CONDENSATE PUMP ASSEMBLY INSTRUCTIONS FOR SANTA FE ADVANCE
STEP 2. Remove middle top cover screw on the
dehumidifier. The screw is located on the drain port side. Do
not discard this screw. It will be used to attach the mounting
bracket. Install hose elbow assembly. Ensure that the
shorter hose is connected to the dehumidifier drain port.
STEP 4. Reinstall screw that was removed
from top cover.
STEP 6. Install the 20 foot drain hose onto the exit port of
the pump. Route drain hose to appropriate drain. Plug in the
condensate pump power cord.
STEP 1. Install hose connector on to drain port.
Install Hose Connector
onto Drain Port.
STEP 3. Align mounting bracket through hole with
dehumidifier screw hole.
Align Bracket and
Screw Hole.
STEP 5. Insert drain hose into the pump opening.
Put Hose into Pump
Install 20ft Hose
Onto Pump Outlet.
Remove Middle Top
Cover Screw.
Install Hose Elbow Assembly. Ensure
that the Shorter Hose is Connected to
the Dehumidifier Drain Port
Santa Fe Advance Condensate Pump Kit Assembly Instructions
Note: Before attaching pump assembly, ensure that the dehumidifier has either the casters or leveling legs installed in it. These will be needed for
additional height. The mounting bracket is not to be used as a support bracket for the dehumidifier.

8" COLLAR ASSEMBLY FOR SANTA FE ADVANCE
Position collar on a flat
surface with tabs up.
Repeat process for exhaust duct. p/n 4026053
Collar
Sheet metal
plenum
Sheet metal
plenum
Collar
Position collar into large
hole. Press firmly so that
tabs of collar go through
the plenum hole.
Press down firmly on the
sheet metal plenum. Lock
the collar in position by
bending the collar tabs
outwards and flatten.
All collar tabs are
flattened.
Step 1.
Step 2.
Step 3.
Step 4.
11 Santa Fe Advance Installer’s & Owner’s Manual

SANTA FE ADVANCE DUCT KIT ASSEMBLY
12 Santa Fe Advance Installer’s & Owner’s Manual 13 Santa Fe Advance Installer’s & Owner’s Manual
Step 1
FRONT DUCT ASSEMBLY: REFER TO FIGURE 1
1. Check sealing foam on the front duct assembly. Ensure that none
has come loose.
2. Place front duct assembly on the intake side of the dehumidifier.
3. Center the front duct assembly. Ensure the sealing foam makes
contact around the plastic intake grill surface. Sealing foam should
not cover any of the inlet portion of the intake grill.
4. DO NOT DRILL PILOT HOLES FOR SCREWS. You will risk
possibly damaging the internal components. Using the
through holes provided in the top duct assembly, screw in the
10-16 X 1/2 screws directly into the plastic housing. Be careful
not to strip. Lightly tighten screws. Do this in all four through hole
locations.
Step 2
TOP DUCT ASSEMBLY: REFER TO FIGURE 1 & 2
1. Check sealing foam on the top duct assembly. Ensure none has
come loose.
2. Place top duct assembly, ensure the sealing foam makes contact
around the plastic surfaces.
3. Center the top duct assembly, ensure the sealing foam makes
contact around the plastic surfaces.
4. Ensure the rear flange of the top duct assembly is seated flush
against the back of the plastic housing. See Figure 2.
5. DO NOT DRILL PILOT HOES FOR SCREWS. You will risk
possibly damaging the internal components. Using the
through holes provided in the top duct assembly, secure back
flange of the top duct assembly first. Drive two 10-16 X 1/2
screws directly into the plastic housing.After the back flange has
been secured, drive in the last two screws (located on the top) into
the plastic housing using the same procedure.
Step 3
1. Start unit and check for any air leaks around the perimeter of the
ducts.
2. If any leaks are found, seal leak with foil tape.
Santa Fe Advance Duct Kit Assembly Instructions
Do not drill any pilot holes into the plastic housing. You may damage the internal components. When installing screws, be careful
not to strip. Lightly tighten screws.

12 Santa Fe Advance Installer’s & Owner’s Manual 13 Santa Fe Advance Installer’s & Owner’s Manual
WARRANTOR:
Therma-Stor LLC
PO Box 8680
Madison, WI 53708
Telephone: [phone]
WHO IS COVERED: This warranty extends only to the
original residential end-user of the Santa Fe Advance
dehumidifier, and may not be assigned or transferred.
FIRST AND SECOND YEAR WARRANTY: Therma-Stor
LLC warrants that, for two (2) years after date of original
purchase the Santa Fe Advance Dehumidifier will operate
free from any defects in materials and workmanship.
Therma-Stor LLC’s exclusive obligation under this warranty
will be to supply, without charge, a replacement for the
dehumidifier which is found to be defective within a two (2)
year period from date of purchase and which is returned
not later than thirty (30) days after said two (2) year period
to Therma-Stor LLC, Madison, WI together with proof of
purchase of the dehumidifier.
THIRD THROUGH FIFTH YEAR WARRANTY: Therma-
Stor LLC further warrants that for a period of five (5) years,
the condenser, evaporator, and compressor of the Santa
Fe Advance dehumidifier will operate free of any defects
in material or workmanship, or Therma-Stor LLC, at its
option, will repair or replace the defective part(s), provided
that all labor and transportation charges for the part(s) shall
be borne by the end-user.
END-USER RESPONSIBILITIES: If warranty service is
to be performed on the Santa Fe Advance, a technician
authorized by Therma-Stor LLC must perform such service.
If the End-user is unable to locate or obtain warranty
service from an authorized technician, he should call
Therma-Stor LLC at the above number and ask for the
Service Department, which will then arrange for covered
warranty service. Warranty service will be performed
during normal working hours.
The End-user must present proof of purchase (lease) upon
request, by use of the warranty card, receipt, invoice or
other reasonable and reliable means. The end-user is
responsible for normal care. This warranty only applies
to residential applications, and is void if the Santa Fe
Advance Dehumidifier is used in commercial and/or
industrial applications including but not limited to water
treatment facilities and industrial process applications.
This warranty is void if the Santa Fe Advance is used in
any swimming pool application. This warranty does not
cover any defect, malfunction, etc. resulting from misuse,
abuse, lack of normal care, corrosion, freezing, flooding,
tampering, modification, unauthorized or improper repair
or installation, accident, acts of nature or any other cause
beyond Therma-Stor LLC’s reasonable control.
LIMITATIONS AND EXCLUSIONS: If any Santa Fe
Advance Dehumidifier part is repaired or replaced, the
new part shall be warranted for only the remainder of the
original warranty period applicable thereto (but all warranty
periods will be extended by the period of time, if any, that
the Santa Fe Advance Dehumidifier is out of service while
awaiting covered warranty service).
UPON THE EXPIRATION OF THE WRITTEN WARRANTY
APPLICABLE TO THE SANTA FE ADVANCE DEHUMIDIFIER
OR ANY PART THEREOF, ALL OTHER WARRANTIES
IMPLIED BY LAW, INCLUDING MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, SHALL ALSO
EXPIRE. ALL WARRANTIES MADE BY THERMA-STOR
LLC ARE SET FORTH HEREIN, AND NO CLAIM MAY BE
MADE AGAINST THERMA-STOR LLC BASED ON ANY
ORAL WARRANTY. IN NO EVENT SHALL THERMA-STOR
LLC, IN CONNECTION WITH THE SALE, INSTALLATION,
USE, REPAIR OR REPLACEMENT OF ANY SANTA FE
DEHUMIDIFIER OR PART THEREOF BE LIABLE UNDER
ANY LEGAL THEORY FOR ANY SPECIAL, INDIRECT OR
CONSEQUENTIAL DAMAGES INCLUDING WITHOUT
LIMITATION WATER DAMAGE (THE END-USER SHOULD
TAKE PRECAUTIONS AGAINST SAME), LOST PROFITS,
DELAY, OR LOSS OF USE OR DAMAGE TO ANY REAL OR
PERSONAL PROPERTY.
Some states do not allow limitations on how long an
implied warranty lasts, and some do not allow the
exclusion or limitation of incidental or consequential
damages, so one or both of these limitation may not apply
to you.
LEGAL RIGHTS: This warranty gives you specific legal
rights, and you may also have other rights which vary from
state to state.
Santa Fe Advance Dehumidifier Limited Warranty

Information in this document is subject to change without notice. No part of
this document may be reproduced or transmitted in any form or by any means,
electronic or mechanical, for any purpose, without the express written permission
of Therma-Stor LLC. © 2006 Therma-Stor LLC. All rights reserved.
PO Box 8680 • Madison, WI 53708
Phone: [phone] • Fax: [phone]
Web: www.thermastor.com • Email: [e-mail]