THERMEx PRO-AS30 User manual

USER MANUAL
CAREMEX HYGIENE STATION
Please read user manual carefully before using.

LED Indicator
Control Box
1. Remove the lid from the drain tank
2. Take out the drain tank and clean
the liquid residual inside
Mind the installation
direction of base plate
Front
Parts List
Sensor Type
Product Name
Sensor Range 2~12cm
Aluminum+Iron Sheet Metal+ABS
5L
Liquid Volume Adjustor
Suitable Liquid
Capacity
SprayLiquid Output
4 pcs AA alkaline batteries
(not included)
Liquid alcoholicity: 75%
1: 0.3ml 2: 0.6ml
Caremex Hygiene Station
Infrared Sensor
Material
Battery
Power Adapter Input Voltage: AC100-240V 50/60Hz
Output Voltage: DC6.0V≥0.8A
Specification
Top Cover Lock
Base Plate
Liquid Tube Connecter
Power / Liquid Adjust Switch
Battery Chamber
Drain Tank
Sensor Zone
Liquid Outlet
Top Cover
①
②
-1-
Back
Back Door Lock
Liquid Tube
5L Liquid Tank
Back Door
Tank Mouth
1190mm
500mm
260mm
390mm
205mm 140mm
Adapter Socket

Installation
Pre-Operation
FM4*13 Screw
(Not included screwdriver）
※The side with screw hole concavity should be placed facing outward
-2-
Unlock the back door, unscrew
the tank cap to take out the tank
for refilling then place it back.
Unlock the top cover to
take out the control box
for battery loading.
Turn on the power and set the
liquid spray volume, there are
two setting.
I small volume: 0.3ml
II large volume: 0.6ml
Replace the control box back inside
then replug the tube in, please make
sure the liquid nozzle is at the right
location.
Lock the top cover.
Place the product horizontally, put the base plate corresponding to the position
of 2 guide posts at the bottom of product.
Install 4 screws to fixate the base plate onto the product, please mind the
installation direction of base plate to make sure an even bottom.
Guide Posts
Filter Valve
1Move the product to stand. 3
2
1 2 Unplug the tube then take
out the whole control box.
3
5
1. Open the battery cap by
pressing the buckle to the left
then insert 4 "AA" batteries
according to the right direction.
2. Connect the DC wire onto
the power port on the right
side of control box.
46
7
Press
down

Ignoring or misunderstanding these signs will result in the following two situations:
This sign indicates “may cause personal injury or property damage”
Mandatory Keep away from fire
Instruction Prohibited Do not disassemble
without permission
Do not expose the unit to direct sunlight to avoid deformation.
Do not use the product rudely.
The product must be securely installed in a stable and reliable place. If the product is not firmly installed,
it will cause damage to the body.
Do not rely on or sit on the product. Otherwise, the product may fall and cause injury.
Please take out the batteries and empty the tank when in long-term unused condition.
Please clean the unit regularly.
Do not clean the unit with water.
Do not intentionally break or crash the unit.
Do not clean the unit with strong corrosive chemical solvent.
-Will cause surface damage or deformation.
Do not let the dust into the liquid tank.
-May block the tube and need to replace the liquid and clean the tank.
Do not disassemble, repair or transform without permission.
Do not fill in corrosive chemicals.
Keep away from fire.
-Will cause breakdown. Please consult the purchase store or customer service for repair issue.
This sign indicates “may cause damage to the product”
Attention
Warning
Attention
Ready For Use
※The drain tank can be taken out for liquid residual clearance.
※The sensor has no reaction on dark or black objects.
※The key for top cover and back door is the same one.
Place your hand under the sensor zone to activate the function, first time use you might need to
operate it few times to let the air out from the tube.
- When use, LED flash white light.
- When battery is low, LED flash red light to remind battery changing.
Trouble Shooting
Safety Precautions
No liquid out
Issue Trouble shooting
a. Check the batteries status;
① If red LED light blinks once every 3 seconds when standby, it indicates the battry voltage is between 3.9V
and 4.8V, the product remains functional.
② If red LED light blinks twice when sensor activated, it Indicates the battery voltage is lower than 3.9V, the
product is out of function.
b. Check if all parts are installed properly;
c. Check if the liquid tank is empty and the liquid is compatible with the product type;
d. Check the motor sound to confirm if the motor works.
e. Clean spray nozzle.
-3-
Warning
LED
INDICATION
ATTENTION