Thermo Scientific Dionex UltiMate 3000 Series User manual

Thermo Scientific Dionex
UltiMate 3000 Series
Column Compartments
TCC-3000SD and TCC-3000RS
Operating Instructions
(Original Operating Instructions)
Revision: 1.5
Date: September 2013
© 2013 Thermo Fisher Scientific Inc.
Doc. No. 4827.3050

UltiMate 3000 Series:
TCC-3000SD and TCC-3000RS Column Compartments
Operating Instructions

UltiMate 3000 Series:
TCC-3000SD and TCC-3000RS Column Compartments
Operating Instructions Page I
Declaration of Conformity
(Original Declaration of Conformity)
Product: Thermo Scientific Dionex UltiMate 3000 - Column Thermostat
Types: TCC-3000SD and TCC-3000RS
Dionex Softron GmbH herewith declares conformity of the above products with
the respective requirements of the following regulations:
•Low-Voltage Directive 2006/95/EC
•EMC Directive 2004/108/EC
The electrical safety of the products was evaluated based on the following
standard:
•DIN EN 61010-1:2010
Safety requirements for electrical equipment for measurement, control and
laboratory use, Part 1: General Requirements
The Electromagnetic Compatibility (EMC) of the products was evaluated based
on the following standard:
•DIN EN 61326:2006
Electrical equipment for measurement, control and laboratory use
EMC Requirements
This declaration is issued for the manufacturer
Dionex Softron GmbH
Part of Thermo Fisher Scientific Inc.
Dornierstraße 4
D-82110 Germering
by the Managing Director, Rüdiger Obst and
den Vice President HPLC, Fraser McLeod.
September 2, 2013

UltiMate 3000 Series:
TCC-3000SD and TCC-3000RS Column Compartments
Page II Operating Instructions

UltiMate 3000 Series:
TCC-3000SD and TCC-3000RS Column Compartments
Operating Instructions Page i
Table of Content
1Introduction................................................................................................................... 1
1.1 How to Use this Manual ............................................................................................ 1
1.2 Safety ......................................................................................................................... 3
1.2.1 Symbols on the TCC and in the Manual...........................................................3
1.2.2 Safety Precautions ............................................................................................ 4
1.2.3 Consignes de Sécurité....................................................................................... 8
1.3 Intended Use ............................................................................................................ 12
1.4 Federal Communications Commission (FCC) Note................................................ 13
2Overview ...................................................................................................................... 15
2.1 Unit Description....................................................................................................... 15
2.2 Operating Principle.................................................................................................. 16
2.3 Configurations ......................................................................................................... 17
2.4 Front Panel Elements............................................................................................... 18
2.5 Rear Panel ................................................................................................................ 19
2.5.1 Power Switch.................................................................................................. 20
2.5.2 Fuse Cartridge ................................................................................................ 20
2.5.3 USB Port......................................................................................................... 20
2.5.4 Digital I/O....................................................................................................... 20
2.6 Interior Components ................................................................................................ 21
2.7 Gas and Humidity Sensors....................................................................................... 22
2.8 Column Switching Valve......................................................................................... 22
2.9 Column Identification System (Column ID) ........................................................... 24
2.10 Pre-Column Heater .................................................................................................. 24
2.11 Post-Column Cooler ................................................................................................ 25
2.12 Operation from Chromeleon.................................................................................... 26
2.13 System Wellness, Predictive Performance, and Diagnostics................................... 27
3Installation................................................................................................................... 29
3.1 Facility Requirements.............................................................................................. 29
3.2 Unpacking................................................................................................................ 29
3.3 Positioning the TCC in the UltiMate 3000 System ................................................. 31
3.4 Connecting the TCC ................................................................................................ 33
3.4.1 General Information ....................................................................................... 33
3.4.2 Connecting the USB Cable............................................................................. 33
3.4.3 Connecting the Power Cord............................................................................ 34
3.4.4 Connecting the Digital I/O ............................................................................. 34
3.5 Setting Up the TCC in Chromeleon......................................................................... 35
3.5.1 Loading the USB Driver for the TCC ............................................................ 35
3.5.2 Installing the TCC .......................................................................................... 37
3.5.3 Configuring the TCC ...................................................................................... 38
3.6 Setting Up the TCC in DCMSLink.......................................................................... 44

UltiMate 3000 Series:
TCC-3000SD and TCC-3000RS Column Compartments
Page ii Operating Instructions
4Preparation for Operation (Startup) ........................................................................45
4.1 Overview..................................................................................................................45
4.2 General Precautions for Connecting Capillaries......................................................46
4.3 Opening the Column Chamber ................................................................................48
4.4 Inspecting the Valve Drainage.................................................................................49
4.5 Installing a Pre-column Heater ................................................................................49
4.6 Installing a Separation Column................................................................................50
4.7 Installing the Post-Column Cooler Insert.................................................................52
4.8 Connecting the Components to the Column Switching Valve ................................53
4.8.1 Connections on a 2-position, 6-port Column Switching Valve......................54
4.8.2 Connections on a 2-position, 10-port Column Switching Valve....................55
4.8.3 Connections on a Multi-Position Column Switching Valve...........................56
4.9 Connecting Drain Tubing.........................................................................................56
4.10 Equilibrating the System..........................................................................................57
5Operation and Maintenance ......................................................................................59
5.1 Power-Up .................................................................................................................59
5.2 Status Screen............................................................................................................60
5.3 Operation from Chromeleon ....................................................................................61
5.3.1 Connecting to Chromeleon .............................................................................61
5.3.2 Direct Control .................................................................................................62
5.3.3 Automated Control .........................................................................................65
5.4 Display Screens (Function Keys and Menus)..........................................................67
5.4.1 Showing the Function Keys............................................................................67
5.4.2 TCC Menus.....................................................................................................68
5.5 Operational Settings.................................................................................................72
5.5.1 Turning on Column Thermostatting ...............................................................73
5.5.2 Turning on Post-Column Thermostatting.......................................................74
5.5.3 Activating Column Identification (Column ID) .............................................75
5.5.4 Selecting the Column......................................................................................76
5.5.5 Adjusting the Sensitivity of the Gas and Humidity Sensors...........................77
5.5.6 Selecting the Status Screen.............................................................................78
5.5.7 Adjusting the Screen Brightness or Contrast..................................................78
5.5.8 SmartStartup and SmartShutdown..................................................................79
5.6 Special Chromeleon Functions ................................................................................80
5.6.1 Ready Temp Delta and Equilibration Time....................................................80
5.6.2 Predictive Performance...................................................................................82
5.6.3 TCC Diagnostics.............................................................................................83
5.6.4 Recording the Temperature Signals................................................................83
5.6.5 Operational Qualification and Performance Qualification .............................83
5.7 Shutting Down the TCC...........................................................................................84
5.8 Routine and Preventive Maintenance ......................................................................86

UltiMate 3000 Series:
TCC-3000SD and TCC-3000RS Column Compartments
Operating Instructions Page iii
6Troubleshooting .......................................................................................................... 87
6.1 Overview.................................................................................................................. 87
6.2 Messages on the TCC Display................................................................................. 88
6.3 Chromeleon Diagnostics Messages ......................................................................... 91
6.4 Operating Problems ................................................................................................. 92
7Service .......................................................................................................................... 95
7.1 General Notes and Safety Precautions..................................................................... 95
7.2 Removing Gases and Humidity from the Column Chamber................................... 97
7.3 Column Switching Valve......................................................................................... 98
7.3.1 Inspecting the Column Switching Valve for Leakage....................................99
7.3.2 Replacing the Valve Pod .............................................................................. 100
7.3.3 Replacing the Valve Stator........................................................................... 105
7.3.4 Rotor Seal and Stator Face Seal ................................................................... 107
7.4 Replacing the Main Power Fuses........................................................................... 109
7.5 Updating the TCC Firmware ................................................................................. 110
8Technical Information.............................................................................................. 113
9Accessories, Consumables, and Spare Parts .......................................................... 115
9.1 Standard Accessories ............................................................................................. 115
9.2 Optional Accessories ............................................................................................. 117
9.3 Consumables and Spare Parts ................................................................................ 120
10 Appendix - Digital I/O (Pin Assignment)................................................................ 125
11 Index........................................................................................................................... 127

UltiMate 3000 Series:
TCC-3000SD and TCC-3000RS Column Compartments
Page iv Operating Instructions

UltiMate 3000 Series:
TCC-3000SD and TCC-3000RS Column Compartments
Operating Instructions Page 1
1 Introduction
1.1 How to Use this Manual
The layout of this manual is designed to provide quick reference to the sections of interest
to the reader when operating the Thermo Scientific™ Dionex™ TCC-3000 Thermostatted
Column Compartment. However, in order to obtain a full understanding of the TCC,
Thermo Fisher Scientific recommends that you review the manual thoroughly before
beginning operation.
The descriptions in this manual apply to the following column compartments in the
UltiMate™ 3000 series:
•TCC-3000SD
•TCC-3000RS
The following conventions apply to the descriptions throughout this manual:
•The term "the TCC" or "the device" is used throughout the manual. If some detail applies
to only one model or version, the model (version) is identified by name.
•If not otherwise stated, the descriptions for the Viper™ capillary connections apply also
to nanoViper™ and possible other Viper capillary connections.
•The device configuration may vary. Therefore, not all descriptions necessarily apply to
your particular TCC.
•The representation of a component in this manual may be slightly different from the real
component. However, this does not influence the descriptions.
•The descriptions in this manual refer to firmware version 1.32 and Chromeleon™ 6.80
Service Release 13. If you want to operate the TCC from Chromeleon 7, note the
information on page 26.
This manual is provided "as is". Every effort has been made to supply complete and
accurate information and all technical specifications have been developed with the utmost
care. The information contained in this manual should not be construed as a commitment
by Thermo Fisher Scientific. Thermo Fisher Scientific assumes no responsibility for any
errors that may appear in this document that is believed to be complete and accurate at the
time of publication and, in no event, shall Thermo Fisher Scientific be liable for incidental
or consequential damages in connection with or arising from the use of this document. We
appreciate your help in eliminating any errors that may appear in this document.
The information contained in this document is subject to change without notice.

UltiMate 3000 Series:
TCC-3000SD and TCC-3000RS Column Compartments
Page 2Operating Instructions
All rights reserved, including those for photomechanical reproduction and storage on
electronic media. No part of this publication may be copied or distributed, transmitted,
transcribed, stored in a retrieval system, or transmitted into any human or computer language,
in any form or by any means, electronic, mechanical, magnetic, manual, or otherwise, or
disclosed to third parties without the express written permission of Thermo Fisher Scientific
Inc.
Trademarks
Analyst is a registered trademark of AB Sciex.
Compass and Hystar are trademarks of Bruker Daltonics.
Empower is a trademark of Waters Corp.
MP35N is a registered trademark of SPS Technologies.
PEEK is a trademark of Victrex PLC.
TitanHP and TitanHT are trademarks of Idex Corp.
Vespel is a registered trademark of E.I. duPont de Nemours & Company.
Microsoft, Windows, and Windows Vista are registered trademarks of Microsoft Corp.
All other trademarks are property of Thermo Fisher Scientific Inc. and its subsidiaries.

UltiMate 3000 Series:
TCC-3000SD and TCC-3000RS Column Compartments
Operating Instructions Page 3
1.2 Safety
The CE Mark label and cTUVus Mark safety label on the instrument indicate that the
instrument is compliant with the related standards.
1.2.1 Symbols on the TCC and in the Manual
The table shows the symbols that are used on the TCC:
Symbol Description
Alternating current—Courant alternatif
Power supply is on (-)—L'instrument est mis sous tension (-) and Power supply
is off (O)—L'instrument est mis hors tension (O)
Surface becomes hot during operation—La surface devient chaude lors du
fonctionnement.
Refer to the Operating Instructions to prevent risk of harm to the operator and to
protect the device against damage.
Référez-vous à ce manuel pour éviter tout risque de blessure à l'opérateur et/ou
protéger l'instrument contre tout dommage.
Label according to the "Measures for Administration of the Pollution Control of
Electronic Information Products" (China RoHS) guideline
Étiquette "Measures for Administration of the Pollution Control of Electronic
Information Products" (China RoHS)
WEEE (Waste Electrical and Electronic Equipment) label—For more
information, see the WEEE Information section in the "Installation and
Qualification Documents for Chromatography Instruments" binder. Étiquette
DEEE (Déchets d'Equipements Electriques et Electroniques)—Pour plus
d'informations, référez-vous au chapitre WEEE Information dans le classeur
"Installation and Qualification Documents for Chromatography Instruments"
At various points throughout the manual, the following symbols indicate messages of
particular importance:
Tip: Indicates general information, as well as information intended to
optimize the performance of the instrument.
Important: Indicates that failure to take note of the accompanying information
could cause wrong results or may result in damage to the instrument.
Important: Indique que ne pas tenir compte de l'information jointe peut conduire
à de faux résultat ou endommager l'instrument.
˜

UltiMate 3000 Series:
TCC-3000SD and TCC-3000RS Column Compartments
Page 4Operating Instructions
Warning: Indicates that failure to take note of the accompanying information
may result in personal injury.
Avertissement: Indique que ne pas tenir compte de l'information jointe peut entraîner
des blessures corporelles.
1.2.2 Safety Precautions
When working with analytical instrumentation, you must know the potential hazards of
using chemical solvents.
Tip: Before operating the TCC for the first time, read this manual once to
make yourself familiar with the contents of this manual.
For the safety precautions in French, see section 1.2.3 (→page 8).
Warning: All users of the device must observe the following safety precautions
and all additional safety precautions in this manual to avoid the
possibility of personal injury or damage to the device when
operating the device or carrying out any maintenance or service
procedures.
Observe any warning labels on the TCC and see the related sections
in these Operating Instructions.
•Protective equipment
When performing any work on or near the HPLC system, wear personal protective
equipment (protective clothing, safety gloves, safety glasses) as required by the hazard of
the mobile phase and sample. For information about the proper handling of a particular
substance and for advice on specific hazards, refer to the material safety data sheet for the
substance you are using. Observe the guidelines of Good Laboratory Practice (GLP).
An eyewash facility and a sink should be close to the device. If any substance splashes on
the eyes or skin, wash the affected area and seek medical attention.
•Hazardous substances
Many organic solvents, mobile phases, and samples are harmful to health. Be sure that
you know the toxic and infectious properties of all substances that you are using. You
may not know the toxic or infectious properties of many substances that you are using. If
you have any doubt about a substance, treat it as if it contains a potentially harmful
substance. For advice on the proper handling of a particular substance, refer to the Safety
Data Sheet (SDS) of the manufacturer. Observe the guidelines of Good Laboratory
Practice (GLP).

UltiMate 3000 Series:
TCC-3000SD and TCC-3000RS Column Compartments
Operating Instructions Page 5
Dispose of waste substance in an environmentally safe manner that is consistent with all
local regulations. Do not allow flammable, toxic, and/or infectious substances to
accumulate. Follow a regulated, approved waste disposal program. Never dispose of
flammable, toxic, and/or infectious substances through the municipal sewage system.
•Hazardous gases
Install the HPLC system in a well-ventilated laboratory. If the mobile phase or sample
includes volatile or flammable solvents, do not allow them to enter the workspace. If the
mobile phase or sample includes volatile or flammable solvents, avoid open flames and
sparks.
•Electrostatic discharge
Discharge of electrostatic energy may lead to sparking and can constitute a fire hazard.
Keep in mind that liquid flowing through capillaries can generate static electricity. This
effect is particularly pronounced in insulating capillaries and with non-conductive
solvents (for example, pure acetonitrile).
Take appropriate measures to prevent the generation of static electricity neat the HPLC
system. For example, make sure that the air humidity level in the laboratory is
sufficiently high and provide proper ventilation, wear anti-static clothing or shoes,
prevent accumulation of air bubbles in waste lines, and use grounded waste containers.
Use only non-conductive capillaries to direct solvents into the waste container. With
electrically conductive capillaries make sure that they are properly grounded.
•Self-ignition of solvents
Do not use solvents for which the self-ignition temperature is below 150 °C. In case of
leakage, these solvents may self-ignite on a hot surface.
•Capillaries, capillary connections, open connections
♦Capillaries, especially non-metallic capillaries may burst, slip out of their fittings or
may not be screwed in. This may result in substances spraying out of the open
connections.
♦In an UltiMate 3000 system, some components are made of PEEK™. This polymer
has superb chemical resistance to most organic solvents. However, it tends to swell
when in contact with trichlormethane (CHCl3), dimethyl sulfoxide (DMSO), or
tetrahydrofuran (THF). In addition, it is attacked by concentrated acids, such as,
sulfuric acid and nitric acid or a mixture of hexane, ethyl acetate, and methanol. In
both cases, capillaries may start leaking or they can burst. Swelling or attack by
concentrated acids is not a problem with brief flushing procedures.
♦Do not use tubing that is stressed, bent, kinked, or damaged.
♦Capillary connections can be contaminated by harmful substances or harmful
substances can escape from open connections.

UltiMate 3000 Series:
TCC-3000SD and TCC-3000RS Column Compartments
Page 6Operating Instructions
♦In an UltiMate 3000 Bio RS system, some system capillaries are made of MP35N®, a
nickel-cobalt based alloy. Individuals with sensitivity to nickel/cobalt may show an
allergic reaction from skin contact.
♦Always wear safety glasses when handling fused silica tubing, for example, during
installation or when cutting capillaries to the length.
•Hot surfaces
To avoid burns, do not touch any metal or plastic parts inside the column chamber while
the temperature is higher than 50 °C. Wait for the chamber to cool down, for example,
before changing a column or before performing any maintenance procedures.
•Disconnect the TCC from all power sources before removing the panels. When the
panels are removed, dangerous electrical connections will be exposed. The enclosure
must be opened only by Thermo Fisher Scientific service personnel.
•Always replace blown fuses with original spare part fuses authorized by Thermo Fisher
Scientific.
•Replace faulty communication cables.
•Replace faulty power cords. Never use a power cord other than the power cords provided
for the device.
•Use only the original spare parts and accessories authorized for the device by Thermo
Fisher Scientific.
•The column switching valves are filled with 2-propanol when they are shipped from the
factory. During initial operation, make sure that the solvents used are miscible.
Otherwise, use an appropriate intermediate solvent.
•When operating the HPLC system, always set a lower pressure limit for the pump. This
prevents damage resulting from leakage or from running the pump dry.
•To prevent damage to the TCC when lifting or moving, always lift the unit by the bottom
sides or sides. Do not lift the TCC by the bottom front or front panel door. This may
damage the door.
•The open front panel door is not designed to carry weight. Do not place any heavy
objects on the open front panel door; this may damage the door.
•After operation, rinse out buffers and solutions that form peroxides.
•Before switching from buffer to organic solution, rinse the analytical system thoroughly
with de-ionized or HPLC grade water.
•When switching to another solvent, ensure that the new solvent is miscible with the one
contained in the HPLC system. If the solvents are not miscible, the system can be
damaged, for example, by flocculation.

UltiMate 3000 Series:
TCC-3000SD and TCC-3000RS Column Compartments
Operating Instructions Page 7
•If a leak occurs, turn off the TCC immediately, stop the pump flow, and remedy the
situation.
•Use only standard solvents (HPLC grade) and buffers that are compatible with all parts
that may be exposed to solvents.
•Before interrupting operation for several days or more or when preparing the TCC for
transport, observe the precautions for shutting down the TCC (→page 84).
•Do not use the TCC in ways other than those described in these Operating Instructions.
•Keep the operating instructions near the device to be available for quick reference.

UltiMate 3000 Series:
TCC-3000SD and TCC-3000RS Column Compartments
Page 8Operating Instructions
1.2.3 Consignes de Sécurité
Si vous utilisez d'instrumentation analytique, vous devez connaître les risques d'utilisation
de produit chimiques.
Veuillez noter : Avant de commencer à utiliser l'instrument, assurez-vous que vous
vous êtes familiarisés avec le contenu de ce manuel.
Avertissement: Toutes les personnes utilisant l’instrument doivent observer les
consignes de sécurité suivantes et dans les autres chapitres de ce
manuel pour éviter une mise en danger de sa personne ou de
dommage à l’instrument pendant l’utilisation et des opérations de
maintenance ou service de l’instrument.
Observez les étiquettes d'avertissement sur l'instrument et référez-
vous aux sections correspondantes dans ce mode d'emploi.
•Equipment de protection
Pour tous les travaux sur le système HPLC ou à proximité, portez l'équipement de
protection personnel (vêtements de protection, gant de sécurité, lunettes de protection)
qui correspond aux risque découlant de la phase mobile et/ou de l'échantillon. Pour les
informations sur la manipulation correcte des composés et des recommandations pour les
situations de risque spécifiques, veuillez consulter la fiche de données de sécurité des
substances que vous utilisez. Veuillez respecter des directives des Bonnes Pratiques de
Laboratoire (BPL).
Une installation permettant de se laver les yeux ainsi qu'un lavabo doivent se trouver à
proximité du système. Si une substance, quelle qu'elle soit, entre en contact avec vos
yeux ou votre peau, rincez abondamment la zone affectée à l’eau, puis.
•Substances dangereuses
De nombreux solvants organiques, phases mobiles et échantillons sont nuisibles à la
santé. Informez-vous de propriétés toxicologiques et infectieuses de toutes les substances
que vous utilisez. Les propriétés toxicologiques et infectieuses de nombreuses substances
peuvent être mal connues. Au moindre doute concernant une substance, traitez-la comme
s'il contenait une substance potentiellement dangereuse. Pour des instructions comment
utiliser correctement des composés particuliers, veuillez consulter à la fiche de données
des sécurités du fabricant respectif. Veuillez respecter des directives des Bonnes
Pratiques de Laboratoire (BPL).
Débarrassez-vous de tous les déchets de substances de manière écologique,
conformément à la règlementation en vigueur au niveau local. Empêchez impérativement
l'accumulation de solvants inflammables, toxiques et/ou infectieux. Suivez un
programme d'élimination des déchets règlementé et approuvé. Ne jetez jamais de
solvants inflammables, toxiques et/ou infectieux dans le système municipal d'évacuation
des eaux usées.

UltiMate 3000 Series:
TCC-3000SD and TCC-3000RS Column Compartments
Operating Instructions Page 9
•Gaz dangereux
Installez le système HPLC dans un laboratoire bien ventilé. Si la phase mobile ou
l’échantillon contient des solvants volatils ou inflammables, vous devez assurer qu'ils ne
pénètrent dans l'espace de travail. Si la phase mobile ou l’échantillon contient des
solvants volatils ou inflammables, évitez les flammes nues et les sources d’étincelles à
proximité.
•Décharge électrostatique
Décharge électrostatique peut provoquer la formation d'étincelles et peut présenter un
risque d’incendie. Veuillez noter que des solvants fluides dans les capillaires peuvent se
charger automatiquement. Cet effet se peut produire particulièrement forte dans les
capillaires isolants et avec des solvants non-conducteurs (par exemple, l'acetonitrile pur).
Prenez des mesures appropriées pour éviter les charges électrostatiques à proximité du
système HPLC. Par exemple, s'assurez qu'il y a une humidité de l'air suffisante et une
ventilation adéquate dans le laboratoire, portez des vêtements ou équipement de
protection antistatique, évitez l'accumulation de bulles d'air dans les lignes de déchets et
utilisez des réservoirs à déchets mis à la terre.
Utilisez uniquement des capillaires non-conducteurs pour diriger solvants au réservoir de
déchets. Capillaires électriquement conducteur devrait être mis à la terre.
•Inflammation spontanée des solvants
N’utilisez aucun solvants avec une température d‘auto-inflammabilité inférieure à
150° C. Si une fuite se produit, ces solvants peuvent s’auto-enflammer au contact d’une
surface chaude.
•Capillaires, connecteur capillaires, connexions ouvertes
♦Des capillaires, en particulier les capillaires non-métalliques, pourraient fendre ou
glisser des connecteurs ou ne peuvent pas être vissés. Ceci peut en résulter aussi que
des substances pourraient jaillir des connexions ouvertes.
♦Dans un système UltiMate 3000, certaines composantes sont en PEEK. Bien que ce
polymère présente une excellente résistance chimique à la plupart des solvants
organiques, il a tendance à gonfler lorsqu'il est en contact prolongé avec du
chloroforme (CHCl3), du diméthyle sulfoxyde (DMSO) ou du tétrahydrofurane
(THF). De plus, il est attaqué par des acides concentrés tels que l'acide sulfurique et
l'acide nitrique ou d'un composé du hexane, éthyle acétate et méthanol. Ceci peut
causer des capillaires de fuite ou risquer des capillaires d’éclater. Ces acides peuvent
cependant être utilisés dans le cadre de procédures de nettoyage, à condition que
l’exposition soit brève.
♦N'utilisez pas de capillaires écrasés, pliés, abimés ou endommagés.
♦Les connecteurs capillaires pour pourrait être contaminé par des substances
dangereuses ou des substances dangereuses pourrait sortir des connexions ouvertes.

UltiMate 3000 Series:
TCC-3000SD and TCC-3000RS Column Compartments
Page 10 Operating Instructions
♦Dans un système UltiMate 3000 Bio RS, certains capillaires du système Viper sont
faits d'alliage de nickel-cobalt MP35N. Contact avec la peau peut provoquer une
réaction chez les personnes qui sont sensibles au nickel/cobalt.
♦Portez des lunettes de protection lorsque vous manipulez des capillaires en silice
fondue (pendant l'installation, découpe, etc.).
•Surface chaude
Pour éviter tout risque de brûlure, ne touchez à aucune partie en métal ou plastique à
l'intérieur du compartiment de colonne tant que la température est supérieure à 50 °C.
Attendez que le four refroidisse, par exemple, avant de changer une colonne ou avant de
procéder à tous opérations de maintenance.
•Quand les capots de protection de l’appareil sont démontés, vous êtes exposés à des
connexions électriques sous haute tension deviennent accessibles. Débranchez
l'instrument de toute source d'alimentation électrique avant de retirer les capots. Ne
démontez les capots de protection que si cela est explicitement demandé au cours de ces
instructions. Les capots de protection devraient être démontés uniquement par le
personnel de service de Thermo Fisher Scientific.
•Remplacez toujours les fusibles grillés par des fusibles de rechange autorisés par Thermo
Fisher Scientific.
•Remplacez les câbles de communication défectueux.
•Remplacez les cordons d'alimentation électrique défectueux. Utilisez uniquement les
cordons d’alimentation électrique spécifique à l’instrument.
•Utilisez seulement des pièces de rechange originales et des accessoires autorisés par
Thermo Fisher Scientific.
•Les vannes de colonne sont stockées sous 2-propanol. Au cours démarrage de
l'instrument, assurez-vous que les solvants utilisés soient miscibles avec le 2-propanol.
Sinon, suivez les étapes intermédiaires appropriées.
•Réglez toujours une limite de pression minimum pour le système HPLC. Ceci prévient
les dommages résultant de fuites ou du fonctionnement à sec de la pompe.
•Lorsque vous soulevez ou l’instrument, tenez-le toujours par le dessous ou par les côtés
de l'unité. Soulever l’instrument par la partie avant inférieure ou par le panneau avant
peut endommager la porte.
•Ne placez aucun objet lourd sur la porte ouverte du panneau avant. Ceci pourrait
endommager la porte.
•Après utilisation, purgez le système des tampons et des susceptibles de former des
peroxydes.

UltiMate 3000 Series:
TCC-3000SD and TCC-3000RS Column Compartments
Operating Instructions Page 11
•Lorsque vous passez d’une solution saline à un solvant organique, effectuez un rinçage
intermédiaire du système HPLC à l'eau dé-ionisée ou qualité HPLC.
•Lorsque vous passez à un autre solvant, assurez-vous que le nouveau solvant soit
miscible avec celui qui se trouve dans le système HPLC. Dans le cas contraire, le
système HPLC peut être endommagé; par exemple, par des floculations!
•Si une fuite se produit, arrêtez immédiatement l’instrument, stoppez le débit de la pompe
et remédiez au problème.
•Utilisez uniquement des solvants (qualité HPLC) et des solutions salines compatibles
avec les matériaux exposés phase mobiles.
•Avant d'interrompre le fonctionnement pendant plusieurs jours ou plus, observez les
précautions figurant en page 84.
•De nombreux solvants organiques et solutions salines sont toxiques. Informez-vous des
propriétés toxicologiques de toutes les phases mobiles que vous utilisez.
•N'utilisez pas l'instrument de manière autre que celles décrites dans ce manuel.
•Conservez ce manuel á proximité de l’instrument pour pouvoir le consulter facilement.

UltiMate 3000 Series:
TCC-3000SD and TCC-3000RS Column Compartments
Page 12 Operating Instructions
1.3 Intended Use
For Research Use Only. Not for use in diagnostic procedures.
The device is designed to be operated only be qualified and authorized personnel. All users
must know the hazards presented by the device and the used substances.
The TCC is designed for laboratory research use in high-performance liquid
chromatography (HPLC) or ultra-high performance liquid chromatography (UHPLC)
applications. It is part of the UltiMate 3000 system, but can be used also with other HPLC
systems if adequate control inputs and outputs are available. A PC with USB port is
required. The TCC is controlled by the Chromeleon CHROMATOGRAPHY
MANAGEMENT SYSTEM. Being part of the UltiMate 3000 system, the TCC can also be
operated with other data systems, such as
•Xcalibur™, Compass™/HyStar™, or Analyst®
To do so, installation of the DCMSLink (Dionex Chromatography Mass Spectrometry
Link) software is required in addition to the installation of the data system.
•Empower™
Installation of the Dionex Instrument Integration Software is required in addition to the
installation of the data system.
For more information, contact the Thermo Fisher Scientific sales organization for Dionex
HPLC Products.
Observe the following:
•Note that the TCC may be operated only with accessories and spare parts recommended
by Thermo Fisher Scientific (→page 115) and within its technical specifications
(→page 113).
•Use only standard solvents (HPLC grade or LC-MS grade: 0.2 µm filtered) and buffers
that are compatible with components in the flow path of the TCC. Note the special
properties of the solvents, such as the viscosity, boiling point, UV absorption (UV/VIS
detector), and refractive index (refractive index detector).
•pH range
Depends on the pre-column heater (→section 2.10, page 24), post-column cooler
(→section 2.11, page 25), and column switching valve (→section 7.3.4, page 107).
•Buffer concentration
Depends on the pre-column heater, post-column cooler and/or column switching valve
SST: Typically up to 1 mol/L (< 0.1 mol/L chloride ions)
Ti/PEEK: Typically up to 1 mol/L (< 1 mol/L chloride ions)
•Also observe the information about the solvent compatibility of the other UltiMate 3000
system modules. For more information, refer to the Operating Instructions for the
modules.