Thetford N301 Installation instructions

Thetford Customer Support
Telephone: [phone]
Fax: [phone]
Web Site: www.thetford.com.au
WARNING: Improper installation, adjustment, alteration, service or
maintenance can cause personal injury or property damage. Refer to
this manual. For assistance or additional information, contact a qualied
installer, service agency, or the gas supplier.
FOR YOUR SAFETY
Do not store or use gasoline or other ammable vapors and liquid in the
vicinity of this or any other appliance.
FOR YOUR SAFETY
If you smell gas:
1. Open windows.
2. Don’t touch electrical switches.
3. Extinguish any open ame.
4. Immediately call your gas supplier.
Part No. 629108D (11-07)
Installation and Owner’s Manual
For Australian refrigerator models:
N301 (93 liter 2-way operation with propane gas or 240 volts AC)
N301.3 (93 liter 3-way operation with propane gas, 240 volts AC, or 12 volts DC )
N401 (128 liter 2-way operation with propane gas or 240 volts AC)
N401.3 (128 liter 3-way operation with propane gas, 240 volts AC, or 12 volts DC )
N501 (164 liter 2-way operation with propane gas or 240 volts AC)
N501.3 (164 liter 3-way operation with propane gas, 240 volts AC, or 12 volts DC )
WARNING: DO NOT install this refrigerator in below deck marine applications. Do not install this refrigerator in xed
indoor cabin or other dwelling applications. This refrigerator must use only Thetford designed and approved outside
air intake and exhaust ventilation for correct and safe operation. Any other ventilation could cause lethal combustion
exhaust fumes and/or explosive propane gas fumes to be in the living area and/or to be below deck.
Thetford Australia
Unit 3, 7 Adrian Road
Campbelleld, VIC 3061
!
!
More information https://www.caravansplus.com.au

Owner’s Manual 2
Table of Contents
Owners manual
Gas Absorption 3 Year Limited Warranty Policy........................... 2
Gas Absorption Warranty Information ..........................................3
Gas Absorption Warranty Questions ............................................3
Safety Awareness.........................................................................4
Safety Instructions........................................................................4
About Your Refrigerator ................................................................4
Storage volume .....................................................................4
Leveling.................................................................................4
Food compartment ................................................................5
Flip-up shelf..................................................................................5
Door bins...............................................................................5
Freezer compartment............................................................5
Operation during travel..........................................................5
Door latch for travel and storage...........................................5
Temperature control system..................................................5
Operating the Refrigerator Controls .............................................5
Control Panel.........................................................................5
Ignition - propane gas operation............................................6
Do a test of the gas safety valve ...........................................6
Start up - AC operation.......................................................... 6
Start up - DC operation .........................................................6
Shut down .............................................................................6
DC Operation Precautions............................................................6
DC Operation Guidelines..............................................................7
Effects of High Altitude on Propane Gas Operation .....................7
Refrigerator Care Checklist ..........................................................7
Defrosting .....................................................................................7
Cleaning8
Drip tray.................................................................................8
Door Sealing.................................................................................8
Refrigerator Maintenance Checklist .............................................8
Refrigerator Storage.....................................................................9
Refrigerator Maintenance.............................................................9
Gas ame appearance..........................................................9
Remove and clean the burner orice ....................................9
Remove the Refrigerator ............................................................10
Reinstall the Refrigerator............................................................10
Replacement Parts..................................................................... 11
Wiring Pictorial............................................................................ 11
Wiring Diagram........................................................................... 11
Installation Manual
Safety Awareness.......................................................................12
Safety Instructions......................................................................12
Certication and Code Requirements.........................................12
Ventilation Requirements............................................................13
Assemble the Enclosure.............................................................13
Install the Upper and Lower Vents..............................................13
Install the Refrigerator ................................................................14
Installation Options.....................................................................15
Install the decorative door panel .........................................15
Reverse the door swing.......................................................15
Change the travel latch position..........................................15
Connect the Electrical Components ...........................................16
Connect the 240 volt AC supply ..........................................16
Connect the 12 volt DC supply (3-way models only)...........16
Connect the Propane Gas Components.....................................17
Connect the propane gas supply system ............................17
Connect the gas supply line to the refrigerator....................17
Examine the gas supply system for leaks ...........................17
Troubleshooting Refrigerator Problems......................................18
Thetford Australia • Unit 3 • 7 Adrian Road • Campbelleld
VIC 3061
Provided it is properly installed, properly maintained and placed
under normal service and use, Thetford Australia warrants its
refrigeration equipment to be free from defects in material and
workmanship for three years with respect to the equipment’s
component parts, and for two years with respect to the labor to
repair or replace such parts, commencing from the original date
of purchase.
Limitations of warranty
1. This Warranty applies only to Thetford gas absorption
refrigerator operating equipment. This Warranty does not
extend to glassware, electric light bulbs, and replaceable fuses.
2. This warranty does not apply to parts and assemblies that
have been subjected to misuse, improper installation, improper
or abnormal service, transit damage, recharging of the cooling
system, accident, re, improper repair, tampering or abuse.
3. Irrespective of the nature of the warranty protection offered or
claimed, the period of warranty shall in no case extend beyond
three years for component parts and two years for the labor
to repair or replace such parts, commencing from the original
date of purchase of the new equipment.
4. In order to obtain the remedy of repair and replacement, the
refrigerator must be brought to any Thetford Service Center
for warranty service. The end consumer is responsible for
all expenses resulting from any remote service call if the
refrigerator cannot be brought into the Thetford Service Center.
5. It is the responsibility of the end consumer to have
maintenance performed upon the warranted equipment one
time during the second year or before the beginning of the third
year after original date of purchase an authorized Thetford
Service Center. Such maintenance is required to maintain
this warranty in effect and failure to perform such maintenance
will void the remainder of the warranty. Required maintenance
during the second year or before the third year after purchase
is cleaning and checking of the following: Burner, Flue, Spiral
Bafe, Roof Cap Screen, and Control Board (operating
controls) Sequence. The cost of this required maintenance
is the end consumer responsibility. A copy of the receipt
covering the required maintenance must be presented to an
authorized Thetford Service Center before Thetford accepts
warranty coverage for the component part during the third year
of warranty coverage.
LIMITATION OF REMEDY
1. THE RESPONSIBILITY OF THETFORD UNDER THIS
OR ANY WARRANTY IS LIMITED TO THE REPAIR OR
REPLACEMENT (AT THETFORD’S OPTION) OF THE
DEFECTIVE PART OR ASSEMBLY.
Thetford Gas Absorption 3 Year Limited
Warranty Policy
Owner’s Manual
More information https://www.caravansplus.com.au

Owner’s Manual 3
Gas Absorption Warranty Information
2. IN NO EVENT AND UNDER NO CIRCUMSTANCES SHALL
THETFORD BE RESPONSIBLE UNDER THIS LIMITED
WARRANTY FOR ANY OTHER CHARGE WHATSOEVER,
INCLUDING BUT NOT LIMITED TO CHARGES OR
CLAIMS FOR LABOR, LOST BUSINESS, LOST TIME,
LOST PROFITS, LOSS OF USE, OR ANY KIND OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, HOWEVER
DENOMINATED OR DESCRIBED. THE REMEDY UNDER
THIS WARRANTY IS LIMITED TO REPLACEMENT OR
REPAIR.
3. SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE EXCLUSION MAY NOT APPLY
TO YOU.
DISCLAIMER OF OTHER WARRANTIES
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES EITHER EXPRESSED OR IMPLIED. ALL
OTHER WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING ANY WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY
DISCLAIMED AND EXCLUDED.
Legal rights
This warranty gives you specic legal rights, and you may have
other legal rights, which vary from state to state.
Your refrigerator is made to provide the ultimate in cooling
satisfaction and will serve you reliably in the years to come.
Thetford refrigerators are the only RV refrigerators made in the
United States and offer a standard limited three-year warranty.
Thetford also offers an additional warranty coverage plan which
extends the standard limited three-year warranty. To activate
your three-year limited warranty and to receive an invitation to
participate in the extended warranty plan, complete and mail the
warranty registration supplied.
Help us to help you.
Write the model number and serial number below for future
reference. These numbers are on the serial plate in the
refrigerator. The serial plate is located in the fresh food
compartment on the top right hand side. Use these numbers
when receiving service or in any correspondence concerning
your refrigerator.
Model number ___________ Serial number ___________
If a problem occurs with your refrigerator, contact any of the
service centers throughout Australia and New Zealand. To
nd an authorized Thetford Service Center near you, please
telephone Thetford Customer Support at (61) 03-9358-0700 or
visit our web site at www.thetford.com.au
Thetford is committed to providing products that are in harmony
with the environment. Your Thetford refrigerator meets all
environmental safety standards.
Gas Absorption Warranty Questions
About your warranty
This warranty coverage begins on the original date of purchase by
the consumer purchaser and is the only warranty for the Thetford
refrigerator. In no case will the Limited Warranty extend beyond two
(2) years for labor and three (3) years for parts and freight. Thetford
reserves the right to change design or specications of a refrigerator
without obligation to modify previously produced refrigerators. There
are no other warranties, either expressed or implied.
What is coverd by this warranty?
- Defects in material and workmanship.
- Parts and labor for two (2) years
- Parts only for the third year if the required maintenance is
performed.
- Freight (ground service only) for shipment of a replacement part
and for return of the defective part.
What is not covered by this warranty?
- Shipping methods other than ground service.
- Defects in glassware, electric light bulbs, and replacement fuses.
- Adjustment of the burner electrode.
- Cleaning of the burner.
- Fees for mobile repair service.
- Mileage or travel expenses to obtain warranty service.
- Expenses for required maintenance as specied in the Limited
Warranty and in the Owner’s Manual.
- Incidental or consequential loss or damage including but not limited
to charges or claims for labor (including labor when no parts are
used for a repair), lost business, lost time, lost prots, lost food,
and lost use.
- Replacement parts that are not manufactured or supplied by
Thetford.
- Defect of a part or assembly when the defect originates from
misuse, improper installation, improper or abnormal service, transit
damage, recharging of the cooling system, accident, re, improper
repair, tampering, or abuse.
What will Thetford do?
For a refrigerator that is properly installed, maintained, and
used as specied in the Installation/Owner’s Manuals, Thetford
responsibilities are:
- Limited to the repair and replacement of parts.
- To provide no charge parts and labor for two (2) years.
- To provide no charge parts only for year 3 if the required
maintenance is performed.
- To provide freight (ground service only) for shipment of a
replacement part and for return of a defective part for three (3)
years.
What will the refrigerator owner do?
To obtain warranty service, the refrigerator owner responsibilities are:
- To use, service, and maintain the refrigerator as specied in the
Installation/Owner’s Manuals.
- To deliver the warranted product to an authorized Thetford Service
Center for warranty repair.
- To show proof that the refrigerator is within warranty coverage.
- To have the required maintenance performed by an authorized
Thetford Service Center one time during year 2 of the Limited
Warranty.
- To pay to have the required maintenance performed.
- To mail paid receipt to Thetford showing required performed before
expiration of year 2 of the Limited Warranty.
- To show proof of the required maintenance before requesting
warranty service in year 3 of the Limited Warranty.
What rights do you have?
The warranty gives you specic legal rights. You may also have
other rights which vary from state to state.
More information https://www.caravansplus.com.au

Owner’s Manual 4
About Your Refrigerator
- When you discard an appliance, remove all doors to
prevent accidental entrapment and suffocation.
- Do not spray liquids near electrical outlets, connections,
or the refrigerator components. Many liquids are
electrically conductive and can cause a shock hazard,
electrical shorts, and in some cases re.
- Do not use electrical appliances inside the food storage
compartment of the refrigerator unless they are of the
type recommended by the manufacturer.
- The refrigerator cooling system is under pressure. Do
not try to repair or to recharge a defective cooling
system. The cooling system contains sodium chromate.
The breathing of certain chromium compounds can
cause cancer. The cooling system contents can cause
severe skin and eye burns, and can ignite and burn with
an intense ame. Do not bend, drop, weld, move, drill,
puncture, or hit the cooling system.
- At regular intervals, make sure that the refrigerator
ue the burner, the vent areas, and the ventilation air
pathway between the vents are completely free from
any ammable material or blockage. After a period of
storage, it is especially important to check these areas
for any ammable material or blockage caused by
animals.
CAUTION:
- The rear of the refrigerator has sharp edges and
corners. To prevent cuts or abrasions when working on
the refrigerator, be careful and wear cut resistant gloves.
Storage Volume:
This refrigerator is made to store fresh and frozen foods and for
making ice.
N301 N401 N501
Total capacity 93 L 128 L 164 L
Freezer capacity 11 L 20 L 20 L
Food compartment capacity 82 L 108 L 144 L
Leveling:
CAUTION: The refrigerator is made to operate
within 3° off level side-to-side and 6° off level front-
to-back (as looking at the front of the refrigerator).
Operating it at more than these limits can cause
damage to the cooling system and create a risk of
personal injury or property damage. Make sure the
vehicle is level before you operate the refrigerator.
Operation during travel:
While the refrigerator should be level when the vehicle is
stopped, performance during travel is not usually effected. Do
not operate the refrigerator on propane gas while travelling. This
can reduce performance, cause an unstable ame, or extinguish
the ame.
WARNING:
- The storage of ammable materials behind or around
the refrigerator creates a re hazard. Do not use the
area behind the refrigerator to store anything, especially
ammable materials (gasoline, cleaning supplies, etc.)
- Do not remove the round ground prong from the
refrigerator AC power cord. Do not use a two prong
adapter or extension cord on the AC power cord.
- A circuit overload can result in an electrical re if the
wires and/or fuses are not the correct size. Either use
the wire and fuse sizes as written in the “Installation
Manual” or refer to your local codes for the correct wire
and fuse sizes.
- Incorrect installation, adjustment, change to, or
maintenance of this refrigerator can cause personal
injury, property damage, or both. Have service and
maintenance work done by your dealer or by a Thetford
authorized Service Center.
- Disconnect both the AC and DC power sources before
doing any maintenance work on the refrigerator. All
service work on this refrigerator must be done by a
qualied service technician.
- Do not bypass or change the refrigerator’s electrical
components or features.
- This refrigerator is not intended for use by children or
by inrm persons unless they have been sufciently
supervised by a responsible person to make sure that
they can use the refrigerator safely.
- Young children should be supervised to make sure that
they do not play with the refrigerator.
Safety Instructions
Read this manual carefully and understand the contents before
you use the refrigerator.
Be aware of possible safety hazards when you see the safety
alert symbol on the refrigerator and in this manual. A signal word
follows the safety alert symbol and identies the danger of the
hazard. Carefully read the descriptions of these signal words to
fully know their meanings. They are for your safety.
WARNING: This signal word means a hazard,
which if ignored, can cause dangerous personal
injury, death, or much property damage.
CAUTION: This signal word means a hazard,
which if ignored, can cause small personal injury or
much property damage.
Safety Awareness
!
!
!
!
!
More information https://www.caravansplus.com.au

Owner’s Manual 5
Control panel:
For N301 models (See Art00976).
For N401 / N501 models (See Art01280).
Thermostat............................................................................ 1
Selector switch...................................................................... 2
Piezo lighter .......................................................................... 3
Gas safety valve ................................................................... 4
Flame meter.......................................................................... 5
The thermostat [1] is the temperature control of the refrigerator.
Number 1 is the warmest temperature setting.
NOTE: If the cooling load changes, you must manually change
the thermostat to maintain the same temperature inside
the refrigerator.
When the outside air temperature is below 10° C, the refrigerator
may have a tendency to freeze food at the colder temperature
settings. To reduce the tendency to freeze food:
- Turn the thermostat to a warmer temperature setting.
- Keep the refrigerator full.
- Put foods that are more likely to freeze on the lower shelf.
The selector switch [2] changes the energy source of the
refrigerator between propane gas ( ), AC electric ( ), DC
electric ( ), and OFF ( ).
The gas safety valve [3] is built into the control panel. As long
as a ame is present, the valve is open and allows propane gas
to ow into the burner. Any loss of ame (empty propane gas
tank, blow out, etc.) closes the safety valve and stops the ow of
propane gas.
The piezo igniter [4] makes a spark which ignites the ame in the
burner.
The ame meter [5] shows if a ame is present in the burner.
Operating the Refrigerator Controls
Food compartment:
Ignite or start up the refrigerator and let it cool for eight hours
before loading with food. If the refrigerator does not start to cool
down after about two hours, contact your dealer or an authorized
Thetford Service Center.
For the best cooling performance:
- Let air move freely inside the entire food compartment.
- Do not cover the shelves with plastic, paper, etc.
To decrease the amount of ice that collects on the cooling ns:
- Cover all liquids and moist foods.
- Let all hot foods cool before putting them in the refrigerator.
- Do not open the door any longer than necessary.
Flip-up shelf (N401 / N501):
The ip-up shelf supplies a space to store tall bottles. To use the
ip-up shelf, lift the center of the shelf and fold it up against the
inside wall of the refrigerator.
Door Bins:
You may put the door bins [52] of the fresh food compartment in
a location that best meets your need (See Art01114). To remove
the bins, lift them over the locator and pull them forward. To
install the bins, push them onto the locator.
NOTE: Do not wash the door bins in a dishwasher. The door
bins are not dishwasher safe.
Freezer compartment:
The freezer compartment is made to keep pre-frozen food frozen
and not to quick freeze food. Keep pre-frozen foods in the
freezer compartment.
NOTE: Do not put other items on the ice tray while the water
is freezing. The water freezes more rapidly if the
thermostat is at the coldest temperature setting.
Door latch for travel and storage:
During travel, the door latch prevents the door from opening.
There are no chains, slides, or any devices that you must
engage.
During storage, the door latch prevents the door from completely
closing. Use it to prevent odors when the refrigerator is shut
down for a long period of time.
To use the door latch for storage (See Art00979):
- Open the door just so the door latch [161] is between the ribs
[166] of the latch plate [162].
1
2
3
4
5
1
5
Art00976
2
13
5
4
1
234
5
1
2
5
43
1
5
Art01280
More information https://www.caravansplus.com.au

Owner’s Manual 6
Ignition - propane gas operation:
1. Open the valve at the propane gas storage tank.
2. Turn the thermostat [1] to the 5 position.
3. Turn the selector switch [2] to the propane gas position ( ).
4. Push and hold in the safety valve [4] and push in the igniter [3]
several times in rapid succession, for about ve seconds:
WARNING: Do not hold in the safety valve for
more than 30 seconds. If there is no ame in
this time, wait at least ve minutes before you try
ignition again. If you continue to hold in the safety
valve, gas will collect in the burner area. This could
cause a re or explosion and result in dangerous
personal injury or death.
- When a ame is present and the ame meter [5] moves into
the green area, wait about ve seconds and release the
safety valve.
- If the ame meter does not move into the green area, do this
step again.
5. Turn the thermostat to the temperature setting that you wish.
Do a test of the gas safety valve:
With an established ame in GAS mode:
1. Close the manual gas shutoff valve [91] of the refrigerator
(See Art01890).
2. After the ame is extinguished, you should hear a sharp “click”
sound within 90 seconds.
NOTE: The gas safety valve should close with a sharp “click“
sound.
3. Open the manual gas shutoff valve of the refrigerator.
4. Without pushing in the gas control, push the igniter several
times rapidly in succession. The burner ame should not
ignite. This means that the gas safety valve is working
correctly.
Start up - AC operation:
- Make sure that 240 volts AC is available.
- Turn the selector switch to the AC position ( ).
- Turn the thermostat to the temperature setting (numbers 2
-5) that you wish.
NOTE: In AC operation only, the number 1 setting of the
thermostat turns the refrigerator off.
Start up - DC operation (3-way models only):
- Make sure that 12 volts DC is available.
- Turn the selector switch to the DC position ( ).
Shut down:
- Turn the selector switch to the OFF position ( ).
DC operation precautions:
This refrigerator is made to operate on DC power while your
vehicle is “in transit” and AC power or propane gas sources are
not available. Operate the refrigerator on DC power only when
the vehicle engine is running.
For the refrigerator to operate correctly on DC power, the battery
must be maintained in a fully charged condition.
For the battery to be fully charged at all times during refrigerator
operation on DC, the vehicle engine must be running and the
battery charging system must be in good operating condition.
Keep in mind the following electrical precautions for DC operation
of the refrigerator:
- Good battery condition is necessary for correct DC operation.
- The capacity of the battery charging system must be more
than what is necessary for the refrigerator and other DC
appliances.
- While the vehicle engine is running, make sure the voltage
of the DC power supply leads at the refrigerator is more than
11.5 VDC.
DC operation guidelines:
DC operation is intended only to maintain the temperature of the
refrigerator and its contents when they are already cool.
The DC operation is not intended for the initial start up and
cooling of the refrigerator. Always use either the AC operation
or propane gas operation to initially start up and cool the
refrigerator. The refrigerator must be cooled and the temperature
must be steady before you operate the refrigerator on DC.
Keep in mind the following guidelines for DC operation of the
refrigerator:
- Use DC operation of the refrigerator while the vehicle is in
transit.
- Do not use DC operation until the refrigerator and its
contents are completely cooled.
- Only use DC operation if the vehicle battery and battery
charging system are in good operating condition.
!
More information https://www.caravansplus.com.au

Owner’s Manual 7
Effects of High Altitude on Propane Gas Op-
eration
When you operate the refrigerator on propane gas at altitudes
higher than 1.7 km above sea level:
- You may experience reduced cooling performance of the
refrigerator.
- You may experience burner outages.
To avoid these possible problems, Thetford recommends that you
operate the refrigerator on AC when at altitudes higher than 1.7
km above sea level.
Defrosting
Refrigerator Care Checklist
Your refrigerator will give you years of trouble free service if you
do these simple checks every three to six months:
- Keep the food compartment and the freezer clean. See
“Cleaning”.
- Defrost the refrigerator as necessary. See “Defrosting”.
- Make sure the door seals correctly. See “Door Sealing“.
- Be aware of any cooling changes that are not because of
weather, loading, or gas control changes. If changes occur,
contact your dealer or an authorized Service Center.
- Make sure the gas supply is propane gas only and not
butane or a butane mixture.
- When in propane gas operation, examine the appearance of
the ame. See “Gas Flame Appearance”.
- Make sure the air ow in the lower intake vent, through the
refrigerator condenser and coils and out the upper exhaust
vent is not blocked or decreased.
- Make sure the area behind the refrigerator is clear. Do
not use the area behind the refrigerator for storage of any
materials or combustible materials, especially gasoline and
other ammable vapors and liquids.
The cooling ns of the refrigerator operate at below freezing
temperature and will naturally form frost from humidity, which is
always present in the air. The humidity inside the refrigerator
increases:
- with higher outside temperature and humidity.
- with the storage of non-sealed fresh foods or warm foods.
- with the amount of time that the door(s) are open.
- with any air leakage into the refrigerator.
It is normal for frost to collect inside the freezer. Excess frost
decreases the cooling performance of the refrigerator. Defrost
the refrigerator and freezer as necessary:
- Remove all food from the refrigerator.
- Turn the refrigerator OFF.
NOTE: Defrosting the refrigerator makes excess water inside
the refrigerator.
- Remove the drain hose from the drip cup at the rear of the
refrigerator (N401 and N501 models only).
- Put the drain hose into a two liter or larger container to
capture water (N401 and N501 models only).
- Put dry towels (etc.) inside the refrigerator and freezer to
absorb melted frost.
CAUTION: High temperatures can cause the
inside surfaces of the refrigerator to warp or melt.
Do not use pans of HOT water, a hair dryer, or
any other high temperature devices to defrost the
refrigerator. Do not use any hard or sharp objects
to remove frost. Damage to the interior of the
refrigerator can occur.
- To increase the speed of defrosting, put pans of WARM
water in the refrigerator and freezer.
- Remove the wet towels (etc.) and dry the interior.
- Remove the drain hose from the large container and put the
drain hose back into the drip cup (N401 and N501 models
only).
- Remove the large container from the enclosure.
- Start up the refrigerator.
- Allow the refrigerator to cool down.
- Return all food to the refrigerator.
!
More information https://www.caravansplus.com.au

Owner’s Manual 8
Refrigerator Maintenance Checklist
Read and understand the following maintenance sections of this
manual.
NOTE: Thetford is not responsible for installation,
adjustment, alteration, service, or maintenance
performed by anyone other than a qualied RV
dealer or an authorized Thetford Service Center.
Have a qualied RV dealer or an authorized Thetford Service
Center do these annual safety and maintenance checks:
- Examine the gas supply lines for leaks.
- Replace or repair if necessary.
- Make sure the propane gas pressure is 2.7 kPa.
- Adjust if necessary.
- Make sure the combustion seal is complete and intact.
- Replace or repair it if necessary.
Door Sealing
If the door does not seal correctly, excess frost will collect inside
the refrigerator. Make sure the door seals correctly:
- Close the door on a piece of paper that is about the size and
thickness of a dollar bill (See Art00980).
- Gently pull the paper.
- You should feel a slight drag between the gasket and the
cabinet.
- Do this on all four sides of the door.
- If you do not feel a slight drag on the
paper, the door is not sealing correctly:
- Make sure the screws of the hinges are tight.
- Make sure the door gasket does not touch the door
latch:
- If the door gasket touches the door latch,
loosen the screws of the door latch.
- Raise the door latch just so it does not touch
and tighten the screws of the door latch.
- Make sure the door latch holds the door closed
A good time to clean the refrigerator is just after you defrost it.
Clean the inside of the refrigerator as often as necessary to avoid
food odors:
- Remove all food from the refrigerator.
NOTE: Do not use abrasive cleaners, chemicals, or
scouring pads because they can damage the
interior of the refrigerator.
- Wash the interior with a solution of liquid dish detergent and
warm water.
- Rinse with a solution of baking soda and clean water.
- Dry with a clean cloth.
- Put all food in the refrigerator.
Drip tray:
To remove and clean the drip tray:
- Locate the plastic clip that is around the wire shelf in front of
the drip tray.
- Remove and save the screw that attaches the plastic clip to
the inside of the refrigerator cabinet.
- Pull the shelf forward to remove from the refrigerator
- Make sure that the drip tray is empty of water.
- Pull the drain tube plug out from the inside of the drip tray
and out of the drain hose.
- Pull the drip tray forward to remove from the slots in the
refrigerator cabinet.
- Clean the drip tray.
- Put the drain tube plug down into the drip tray and push the
drip tray back into the original position.
- Push the drain hose back onto the drain tube plug.
- Put the wire shelf and plastic clip back in the original position.
- Attach the plastic clip with the screw.
Cleaning
More information https://www.caravansplus.com.au

Owner’s Manual 9
Refrigerator Storage
Before the refrigerator is stored for an extended (seasonal)
period of time:
- Defrost and clean the interior of the refrigerator.
- Close the doors with the storage latch.
If the refrigerator is stored for an extended period of time, before
start up:
- Make sure there are no obstructions in the vents, the
ventilation air pathway, the burner, the orice, or the ue
area.
- Make sure the burner and the burner orice are clean (See
Art00956).
- Clean if necessary.
- Make sure the electrode spark gap [3] is 3-5 mm (See
Art00955).
- Adjust if necessary.
- Make sure the AC voltage is 216 - 252 volts and the DC
voltage is 11.7 - 15.4 volts.
- Make sure the thermocouple tip is clean and secure.
- Make sure the area at the rear of the refrigerator is free of
any combustible materials, gasoline, and other ammable
vapors and liquids.
Refrigerator Maintenance
Gas ame appearance:
While in propane gas operation, examine the appearance of the
gas ame:
- Turn the thermostat to the 5 position.
- Open the lower intake vent.
CAUTION: The burner box cover can be hot.
Wear gloves to avoid burns.
- Open the burner box door [165] and look at the gas ame
[75] (See Art00955 and Art01890).
- The ame should be:
- a darker blue color on the inside of the ame and a
lighter blue color on the outside of the ame.
- a constant shape without ickering.
- Contact your dealer or Thetford authorized service
center if the ame is:
- yellow
- ickering or changing shape.
- Make sure the ame does not touch the inside of the
ue tube [76].
- If the ame touches the inside of the ue tube, contact
your dealer or an authorized Thetford Service Center.
- Close the burner box door.
Remove and clean the burner orice:
NOTE: Your dealer or an authorized Thetford Service Center
must do this procedure.
To remove and clean the burner orice:
- Close the valve at the propane gas tank(s).
- Close the manual shut off valve of the refrigerator.
- Shut down the refrigerator..
- Open the lower intake vent.
CAUTION: The burner box cover can be hot.
Wear gloves to avoid burns.
- Remove the burner box cover by removing one screw.
WARNING: To avoid possible propane gas leaks,
always use two wrenches to loosen and tighten the
gas supply line at the refrigerator’s manual shut off
valve.
- Remove the are nut from the orice assembly [77] (See
Art00956).
- Remove the orice assembly from the burner [78].
WARNING: Do not try to remove the orice
[79] from the orice adapter [80] when cleaning.
Removal will damage the orice and seal of the
orice and can cause a propane gas leak. Leaking
propane gas can ignite or explode which can result
in dangerous personal injury or death. Do not clean
the orice with a pin or other objects.
!
!
!
!
More information https://www.caravansplus.com.au

Owner’s Manual 10
NOTE: Your dealer or an authorized Thetford Service Center
must do this procedure.
WARNING: Make sure the combustion seal is
not broken, is completely around the refrigerator
mounting anges, and is between the mounting
anges and the wall of the enclosure. If the
combustion seal is not complete, exhaust fumes
can be present in the living area of the vehicle. The
breathing of exhaust fumes can cause dizziness,
nausea, and in extreme cases, death.
1. Push the refrigerator completely into the enclosure.
2. Remove the door from the refrigerator.
3. Put the screws though the mounting anges and into the wall.
4. Attach the door to the refrigerator
CAUTION: The rear of the refrigerator has sharp
edges and corners. To prevent cuts or abrasions
when working on the refrigerator, be careful and
wear cut resistant gloves.
5. Open the lower intake vent and put the screws through
refrigerator and into the oor.
WARNING: To avoid possible propane gas leaks,
always use two wrenches to loosen and tighten the
gas supply line at the refrigerator’s manual shut off
valve.
6. Attach the gas supply line to the manual shut off valve of the
refrigerator.
7. Open the valve at the propane gas tank(s).
WARNING: Do not allow the leak checking
solution to touch the electrical components. Many
liquids are electrically conductive and can cause a
shock hazard,electrical shorts, and in some cases
re.
8. Examine the gas supply line for leaks.
9. Connect the DC wiring to the refrigerator:
- Install the DC fuse or connect the DC wiring to the battery or
the converter.
- Connect the DC wires from the refrigerator.
10. Connect the AC power cord to the receptacle.
Reinstall the Refrigerator
Remove the Refrigerator
NOTE: Your dealer or an authorized Thetford Service Center
must do this procedure.
CAUTION: The rear of the refrigerator has sharp
edges and corners. To prevent cuts or abrasions
when working on the refrigerator, be careful and
wear cut resistant gloves.
1. Close the valve at the propane gas tank(s).
WARNING: To avoid possible propane gas leaks,
always use two wrenches to loosen and tighten the
gas supply line at the refrigerator’s manual shut off
valve.
2. Open the lower intake vent and remove the gas supply line
from the manual shut off valve of the refrigerator.
3. Remove the AC power cord from the power point.
4. Remove the DC wiring from the refrigerator:
- Remove the DC wiring from the battery or the converter of
the vehicle.
- Put a mark on the DC wires so you can put them back in the
correct location.
- Remove the DC wires from the refrigerator.
5. Remove the screws which fasten the refrigerator to the oor.
6. Remove the door from the refrigerator.
7. Remove the screws which fasten the refrigerator to the wall.
8. Remove the refrigerator from the opening.
9. Attach the door to the refrigerator.
- Clean the orice assembly with air pressure and alcohol only.
- Using a wrench, assemble the orice assembly to the burner.
- Assemble the are nut to the orice assembly.
- Tighten the are nut by hand.
- Hold the orice assembly securely and, using a wrench,
tighten the are nut 1/4 revolution only.
- Examine all of the connections for gas leaks.
!
!
!
!
!
!
More information https://www.caravansplus.com.au

Owner’s Manual 11
The parts of the wiring pictorial are (Art01855):
1............................................................. 240 VAC Power cord
2..............................................................................DC heater
3............................................................................ 3 Amp fuse
4...................................................................... Selector switch
5....................................................................... Thermocouple
6............................................... Thermostat / gas safety valve
7......................................................Thermocouple interrupter
8.......................................................................... Flame meter
9.............................................................................. AC heater
10........................................................-12 VDC Power supply
11 ....................................................... +12 VDC Power supply
12...........20 Amp fuse(N301) 25 Amp fuse (N401 and N501)
Wiring Pictorial
Replacement Parts
You may purchase replacement parts through your local RV
dealer or an authorized Thetford Service Center.
More information https://www.caravansplus.com.au

Owner’s Manual 12
Safety Instructions
Safety Awareness
Read this manual carefully and understand the contents before
you install the refrigerator.
Be aware of possible safety hazards when you see the safety
alert symbol on the refrigerator and in this manual. A signal word
follows the safety alert symbol and identies the danger of the
hazard. Carefully read the descriptions of these signal words to
fully know their meanings. They are for your safety.
WARNING: This signal word means a hazard,
which if ignored, can cause dangerous personal
injury, death, or much property damage.
CAUTION: This signal word means a hazard,
which if ignored, can cause small personal injury or
much property damage.
WARNING:
- This refrigerator is made for use in RV and towable
applications, and is correct for camping use. It is made
to operate with, and be connected to, multiple energy
sources. Disconnect all energy sources before you
remove the refrigerator or do servicing to the refrigerator.
- This refrigerator is not approved for use as a free standing
refrigerator. It is equipped for the use of propane gas only
and can not be changed to use any other fuels (natural
gas, butane, etc.).
- Incorrect installation, adjustment, alteration, or
maintenance of this refrigerator can cause personal injury,
property damage, or both.
- Obey the instructions in this manual to install the intake
and exhaust vents.
- Do not install the refrigerator directly on carpet. Put the
refrigerator on a metal or wood panel that extends the full
width and depth of the refrigerator.
- Do not allow anything to touch the refrigerator cooling
system.
- Propane gas can ignite and cause an explosion that can
result in property damage, personal injury, or death. Do
not smoke or create sparks. Do not use an open ame
to examine the propane gas supply line for leaks. Always
use two wrenches to tighten or loosen the propane gas
supply line connections.
- Make sure the electrical installation obeys all applicable
codes. See “Certication and Code Requirements”
section.
Certication and Code Requirements
Installation Manual - Do not bypass or change the refrigerator’s electrical
components or features.
- Do not spray liquids near electrical outlets, connections, or
the refrigerator components. Many liquids are electrically
conductive and can cause a shock hazard, electrical
shorts, and in some cases re.
- The refrigerator cooling system is under pressure. Do not
try to repair or to recharge a defective cooling system.
- The cooling system contains sodium chromate. The
breathing of certain chromium compounds can cause
cancer. The cooling system contents can cause severe
skin and eye burns, and can ignite and burn with an
intense ame. Do not bend, drop, weld, move, drill,
puncture, or hit the cooling system.
CAUTION:
- The rear of the refrigerator has sharp edges and corners.
To prevent cuts or abrasions when working on the
refrigerator, use caution and wear cut resistant gloves.
This refrigerator is certied under the latest edition of the
Australian Gas Association Standard AS4555/AG105 and the
Australian National Electric Standard for household and similar
electrical appliances AS/NZS 3350.1:1994.
The refrigerator is made for installation in a caravan or a
recreational vehicle. The installation must obey the requirements
of this “installation Manual” for the THETFORD limited warranty
to be in effect.
The installation must agree with local codes. In the absence of
local codes, the installation must obey these standards:
- Gas Installations AS5601.
- National Fuel Gas Code, ANSI Z223.1 (latest edition).
- Manufactured Home Construction and Safety Standard, Title
24 CFR, Part 3280.
- Standard for Recreational Vehicles, RVIA A119.2 latest
edition.
- All gas supply piping and ttings must obey local, and
national codes about type and size.
!
!
!
!
More information https://www.caravansplus.com.au

Owner’s Manual 13
Ventilation Requirements
WARNING: The completed installation must:
- Make sure there is sufcient intake of fresh air for
combustion.
- Make sure the living space is completely isolated from
the combustion system of the refrigerator.
- Make sure there is complete and unrestricted ventilation
of the ue exhaust which, in gas mode, can produce
carbon monoxide. The breathing of carbon monoxide
fumes can cause dizziness, nausea, or in extreme
cases, death.
- Make sure the refrigerator is completely isolated from its
heat generating components through the correct use of
bafes and panel construction.
Certied installation needs one lower intake vent and one upper
exhaust vent. Install the upper exhaust vent either through the
roof or through the side wall of the vehicle exactly as written
in this manual. Any other installation method voids both the
certication and the factory warranty of the refrigerator.
The bottom of the opening for the lower intake vent, which is also
the service access door, must be even with or immediately below
the oor level. This allows any leaking propane gas to escape to
the outside and not to collect at oor level.
While there are no maximum clearances specied for
certication, the following maximum clearances are necessary for
correct refrigeration:
Bottom 0 mm min. 0 mm max.
Each Side 0 mm min 3 mm max.
Top 0 mm min. 6 mm max.
Rear 0 mm min. 25 mm max.
These clearances plus the lower and upper vents cause the
natural air draft that is necessary for good refrigeration. Cooler
air comes in through the lower intake vent, goes up around the
refrigerator coils where it removes the excess heat from the
refrigerator components, and goes out through the upper exhaust
vent. If this air ow is blocked or decreased, the refrigerator will
not cool correctly.
Assemble the Enclosure
1. Make sure the enclosure is:
N301 models
756 mm high x 521 mm wide x 543 mm deep.
N401 models
929 mm high x 602 mm wide x 620 mm deep.
N501 models
1083 mm high x 602 mm wide x 620 mm deep.
2. Make sure the oor is solid and level.
- The oor must be metal or a wood panel and extend the full
width and depth of the enclosure.
- The oor must be able to support the weight of the
refrigerator and its contents.
3. Make sure there are no adjacent heat sources such as a
furnace vent, a hot water heater vent, etc.
Install the Lower and Upper Vents
1. Using the following chart, decide which vents and rough
opening (RO) sizes to use.
Certied Vent P/N RO Height RO Width
Upper Roof 622293 610 mm 133 mm
Exhaust Vent
Upper Side 617485 184 mm 457 mm
Exhaust Vent
Lower Side 617484 248 mm 492 mm
Intake Vent
Universal Upper 620505 157 mm 452 mm
& Lower Vent
Universal Upper 621156 349 mm 546 mm
& Lower Vent
2. Install the lower intake vent (See Art01608):
NOTE: The lower intake vent is also the service access opening
for the components on the rear of the refrigerator.
WARNING: Make sure the bottom of the opening
of the lower intake vent is even with or immediately
below the oor level. This allows any leaking
propane gas to escape to the outside and not to
collect at oor level.
- Make sure the bottom of the opening of lower intake vent is
even with or immediately below the oor level.
- Align the lower intake vent [9] vertically below the coils [10]
and the condenser [11] of the refrigerator.
!
!
More information https://www.caravansplus.com.au

Owner’s Manual 14
3. Install the upper exhaust vent:
- If you install the roof exhaust vent (see Art01638):
CAUTION: Make sure that no sawdust, insulation,
or other construction debris is on the refrigerator or
in the enclosure. Debris can cause a combustion
hazard and prevent the refrigerator from operating
correctly.
NOTE: Tighten the screws of the upper roof exhaust cap to 11.5
kgf/cm max. Also make sure that the air ow around the
upper roof exhaust cap is not blocked or decreased by
other roof mounted features such as a luggage carrier,
an air conditioner, a solar panel, etc.
- If the design of the vehicle allows, install the roof
exhaust vent [12] directly above the condenser [11] of
the refrigerator.
- Install a bafe [13] to prevent stagnant hot air in the
area [14] above the refrigerator.
- Make sure there is less than 6 mm clearance
[15] between the bafe and the top of the
refrigerator.
- Make sure the bafe is the full width of the
inside of the enclosure.
- If the design of the vehicle does not allow you to install
the roof exhaust vent directly above the condenser of
the refrigerator:
- Align the roof exhaust vent [12] above the lower
intake vent and move it inboard as necessary (See
Art01639).
- Install two bafes [13] to prevent stagnant hot air in
the area [14] above the refrigerator.
- Make sure both bafes are the full width of the
inside of the enclosure.
- Make sure that both bafes are no more than
45° from vertical [20].
- Put one bafe between the top rear edge of the
refrigerator and the inside edge of the upper
exhaust vent opening.
- Make sure there is less than 6 mm
clearance [15] between the bafe and the
top of the refrigerator.
- Put the other bafe between the outside edge
of the upper exhaust vent opening and the side
wall of the vehicle.
- If you install the upper side exhaust vent (See Art01637):
- Make sure the distance [25] from the oor level to the
top of the rough opening for the upper exhaust vent is
at least 940 mm for N301 models, 1060 mm for N401
models, and 1210 mm for N510 models or poor cooling
performance can occur.
- Align the upper exhaust vent [24] horizontally above the
lower intake vent [9] of the refrigerator.
- Install a bafe [13] to prevent stagnant hot air in the area
[14] above the refrigerator.
- Make sure there is less than 6mm clearance
[15] between the bafe and the top of the
refrigerator.
- Make sure the bafe is the full width of the
inside of the enclosure.
- If there is more than 25 mm of clearance between the rear
of the refrigerator and the enclosure, add two bafes [16]
to the rear of the enclosure (See Art01637, Art01638, and
Art01639):
- Put one bafe at the top edge of the lower intake vent
[9].
- Put the other bafe at the lower edge of the condenser
[11] of the refrigerator.
- Make sure the bafes are less than 6 mm from the
coils [10] and condenser of the refrigerator.
- Make sure the bafes are the full width of the inside
of the enclosure.
- If there is more than 13 mm of clearance between either side
of the refrigerator and the wall, ll the space with berglass
insulation or add a bafe to eliminate the excess clearance.
Put the refrigerator in position (see Art01288):
WARNING: Make sure the combustion seal [28]
is not broken, is completely around the refrigerator
mounting anges [156], and is between the
mounting anges and the wall of the enclosure. If
the combustion seal is not complete, exhaust fumes
can be present in the living area of the vehicle. The
breathing of exhaust fumes can cause dizziness,
nausea, or in extreme cases, death.
- On N401 and N501 models, remove the door from the
refrigerator (See “Reverse the door swing” section).
- Put screws through the holes of the refrigerator mounting
anges and into the enclosure wall.
- Attach the door to the refrigerator.
- Put a screw through the holes [121] in the braces at the
lower rear corners of the refrigerator and into the oor.
Install the Refrigerator
!
!
More information https://www.caravansplus.com.au

Owner’s Manual 15
Installation Options
Install the decorative door panel:
NOTE: The decorative panels must be 5 mm or less in thickness.
- Make a decorative door panel [38] that is (See Art00977):
- 659 mm high x 511 mm wide for N301 models.
- 787 mm high x 541 mm wide for N401 models.
- 939 mm high x 541 mm wide for N501 models.
- Push the decorative door panel into the slots [157] of the
door end caps [158].
- Push each panel retainer [37] into the slot on the edge of the
door.
Reverse the door swing:
This refrigerator has hinges that allow you to change the direction
that the door opens by moving the hinges to the opposite corner
(See Art01313).
1. Remove the door:
- Turn out and save the upper hinge pin [63].
- Open the door a small amount and pull the top of the door
away from the upper hinge of the refrigerator.
- Lift the door off of the lower hinge pin [64].
- Turn out and save the lower hinge pin.
2. Change the position of the hinges:
- Remove the screws from the upper hinge [159].
- Put this hinge on the other side as the lower hinge.
- Attach the hinge with the screws.
- Turn the lower hinge pin down into this hinge.
- Remove the screws from the lower hinge [160].
- Remove the screws from the travel latch [161].
- Put this hinge on the other side as the upper hinge.
- Attach the hinge with the screws.
3. Change the position of the travel latch (See Art01313 and
Art01571):
- Put the travel latch on the other side of the refrigerator.
- Attach the travel latch with the screws.
- Remove the screw [41] from the travel latch plate [162] on
the door.
- Remove the screw [41] from the ller plate [163] on the door.
- Put the travel latch plate on the other side of the door.
- Attach the travel latch plate with the screw.
- Put the ller plate on the other side of the door.
- Attach the ller plate with the screw.
4. Install the door:
- Put the door down onto the lower hinge pin.
- Align the holes in the upper hinge and the ller plate and hold
in this position.
- Screw the upper hinge pin down into the upper hinge and
into the door.
- Tighten all of the screws.
- Make sure the travel latch fully engages the travel latch plate.
- The travel latch should engage the travel latch plate 5
mm.
- If not, loosen the screws and adjust the height of the
travel latch.
- Tighten the screws.
Change the travel latch position:
This refrigerator allows you to put the travel latch either at the top
of the door or at the bottom of the door regardless of the door
swing direction (See Art01570 and Art01572).
1. Change the position of the travel latch plate:
- Remove the screw [41] from the travel latch plate [162] on
the door.
- Remove the screw [41] from the ller plate [163] on the
oposite end of the door.
- Put the travel latch plate on the opposite end of the door.
- Attach the travel latch plate with the screw.
- Put the ller plate on the opposite end of the door.
- Attach the ller plate with the screw.
2. Change the position of the travel latch:
- Remove the screws from the travel latch [161].
- Put the travel latch on the opposite end of the refrigerator.
- Attach the travel latch with the screws.
More information https://www.caravansplus.com.au

Owner’s Manual 16
NOTE: The current draws are nominal values.
N301 models
AC Operation 240 volts AC
(216 volts min. - 264 volts max.)
Current Draw 0.75 Amps at 240 volts AC
DC Operation 12 volts DC
(11.5 volts min. - 15.4 volts max.)
Current Draw 12.0 Amps at 12 volts DC
14.0 Amps at 14 volts DC
N401 and N501 models
AC Operation 240 volts AC
(216 volts min. - 264 volts max.)
Current Draw 1.0 Amps at 240 volts AC
DC Operation 12 volts DC
(11.5 volts min. - 15.4 volts max.)
Current Draw 14.1 Amps at 12 volts DC
16.5 Amps at 14 volts DC
This refrigerator operates on both AC and DC electrical sources.
Operation out of these limits may damage the refrigerator’s
electrical circuit parts and will void the warranty.
WARNING: The rear of the refrigerator cooling
system has hot surfaces and sharp surfaces that
can damage electrical wiring. Make sure that there
is a good clearance between all electrical wiring
and the cooling system of the refrigerator. Position
any electrical wiring within the refrigerator enclosure
opposite the burner side of the refrigerator. Do not
put any electrical wiring through the roof exhaust
vent. Failure to correctly position electrical wiring
can result in electrical shock or re.
Connect the 240 volt AC supply:
WARNING: Connect the AC power cord only to a
grounded three-prong power point. Do not remove
the earth pin from the power cord. Do not use a
two-prong adapter or an extension cord. Operation
of the refrigerator without correct ground can cause
dangerous electrical shock or death if you are
touching the metal parts of the refrigerator.
Put the AC power cord into a grounded three-prong power point:
- Make sure the power point is 100-150 mm above the oor
of the enclosure and is positioned within easy reach of the
lower intake vent.
- Make sure the power cord does not touch the burner cover,
the ue pipe, or any hot component that could damage the
insulation of the power cord.
Connect the Electrical Components Connect the 12 volt DC supply (3-way models only):
As the distance from the vehicle battery to the refrigerator
increases, the correct wire size and fuse size also increases. If
the wire size is too small for the distance, a voltage drop occurs.
The voltage drop decreases the output of the system heater and
causes poor cooling performance.
1. Determine the min. wire size and the max. fuse size to use:
WARNING: If you use an incorrect wire size and/
or fuse size, electrical re can result.
- Measure the distance from the vehicle battery to the
refrigerator and use the following size wire and fuse:
Distance Models Min wire size Fuse size
5 m N301 4 mm² 20 Amp
N401/N501 4 mm² 30 Amp
8 m N301 6 mm² 30 Amp
N401/N501 6 mm² 40 Amp
- If the wire is larger than the min. size, use the correct fuse
per local codes.
The wire connections must be clean, tight and free of corrosion.
If any of these items are not correct:
- A voltage drop to the refrigerator will occur.
- The voltage drop will reduce the cooling performance of the
refrigerator.
The terminals for connecting the DC power supply are marked
positive (+) and negative (-). Make sure that:
- Each DC power supply wire is attached to the correct polarity
terminal.
- The chassis or the vehicle frame is not used as one of the
conductors.
- The DC power supply wires including the fuses are routed
directly from the battery to the refrigerator.
!
!
!
More information https://www.caravansplus.com.au

Owner’s Manual 17
2. Connect the D.C. power supply wires:
- Attach a fully insulated 6.35 mm Quick Connect terminal to
each DC power supply wire.
- Push the positive (+) DC power wire onto the white DC wire.
- Push the negative (-) DC power wire onto the yellow DC
heater wire.
- Make sure each DC power supply wire is on the correct
polarity terminal.
Connect the Propane Gas Components
This refrigerator operates on propane gas at a pressure of
2.7kPa propane. The refrigerator gas usage is:
N301 models 1.25 MJ/h
N401 and N501 models 1.4 MJ/h
Connect the propane gas supply system:
WARNING: Be very careful when working on or
near the propane gas system.
- Do not smoke or use an open ame near the propane
gas system.
- Do not use an open ame to examine for leaks.
- Do not connect the refrigerator to the propane gas tank
without a pressure regulator between them.
- To avoid a propane gas leak, always use two wrenches
to tighten or loosen the gas supply line connections.
- Leaking propane gas can ignite or explode and result in
dangerous personal injury or death.
Connect the gas supply line to the refrigerator:
- Make sure all tubing and ttings obey all local, state, and
national codes about size and type.
- Use of 3/8 inch copper tubing as the gas supply line and
a 3/8 inch SAE (UNF 5/8-18) male are tting as the
connection to the refrigerator.
- Put the propane gas supply line up through the oor of the
enclosure.
- Make sure the hole through the oor is large enough to allow
clearance for the gas supply line.
- Put a weather resistant seal (grommet, sealant, etc.) around
the gas supply line where it goes through the oor to prevent
vibration and abrasion.
- To prevent vibration and abrasion, make sure that the gas
supply line is not against anything in the enclosure.
- Attach the gas supply line to the bulkhead tting [91] of the
refrigerator (See Art01890).
Examine the gas supply system for leaks:
WARNING: Do not allow the leak detecting
solution to touch the electrical components. Many
liquids are electrically conductive and can cause a
shock hazard, electrical shorts, and in some cases,
re.
Use a leak detecting solution to examine the gas supply line and
all propane gas connections for leaks.
If you use compressed air for the test:
- The pressure at the manual shut off valve of the refrigerator
must not be more than 3.5 kPa.
- If the air pressure is more than 3.5 kPa, remove the gas
supply line from the bulkhead tting of the refrigerator before
the test.
- If the air pressure is equal to or less than 3.5 kPa, close the
manual shutoff valve of the refrigerator before the test.
!
!
More information https://www.caravansplus.com.au

Owner’s Manual 18
Troubleshooting Refrigerator Problems
If you unable to correct your refrigerator problem after using this guide, see your dealer or an authorized Thetford Service
Center.
Problem Corrective Action
The refrigerator does not operate on AC
Check:
- That the refrigerator is plugged in.
- That the thermostat is turned to setting numbers 2-5. Setting number 1
is an OFF position in AC operation.
The refrigerator does not operate on propane
gas.
Check:
- That the propane gas supply line is purged.
- That the propane gas tank(s) are not empty.
- That the valve of the propane gas tank(s) is open.
- That the propane gas is at the correct pressure.
- That the manual shut off valve of the refrigerator is open.
The refrigerator does not operate on DC.
Check:
- That the battery charging equipment of the vehicle is operational.
- That the AC/DC converter is operational (if applicable).
- That the DC connection to the refrigerator is not loose.
- See your dealer or authorized Thetford Service Center.
The refrigerator does not cool correctly on AC,
DC, or propane gas.
Check:
- That the refrigerator vents are unobstructed and remove any obstructions.
- That the vehicle is level within 3° from side-to-side and 6° from front-to-
back.
Excessive frost collects in the freezer or on the
ns in the refrigerator compartment.
Check:
- That all food storage containers in the refrigerator are sealed.
- That you open the refrigerator door only when necessary.
- That the door gasket seals correctly.
- That the refrigerator and freezer are defrosted.
Art01854
More information https://www.caravansplus.com.au

Owner’s Manual 19
Art 00956
77 78
79
80
Art00977
1
2
3
4
1
3
2
Art00979
Art00980
75
76
Art00955
167
Art01114
52
More information https://www.caravansplus.com.au

162
163
41
41
Art01570
Art01571
162
163
41
Art01288
28
156
121
Art01313
63
64
159
160
161
More information https://www.caravansplus.com.au