THORLABS PDA015C User manual


January26,2017
TTN122711‐D04,RevA



PDA015C(/M) InGaAs Amplified Detector
Safety & Quick Start Guide
Note:Theinformationcontainedinthisdocumentisforsafetypurposes.Thorlabs'greenefforts
areaimedatreducingwasteandpreservingourplanet'snaturalresources.Tothatend,wehave
createdawebpagesothatyoucandigitallyread,download,andsaveacopyofthefullproduct
manualand/orotherdocumentationforanyitemonourwebsite:www.thorlabs.com/manuals
Description: The PDA015C(/M) is a fixed gain, 380 MHz BW, InGaAs detector designed for detection of
optical signals in the 800 to 1700 nm wavelength range. It has a frequency response from DC-380 MHz, an
impulse response of 1 ns, and a transimpedance gain of 50 kV/A. Each PDA015A has a power supply connector
designed to work with the LDS1212 linear power supply (±12 VDC, 200 mA) that is included with each unit.
The PDA015C also includes a removable SM1T1 SM1 Adapter with internal threads and SM1RR retaining ring.
Safety Information
General: All statements regarding safe operation and technical data in the instruction manual will only apply
when the unit is operated correctly. A copy of the full product manual can be accessed online at the
following website: www.thorlabs.com/manuals
Before Applying Power: Each PDA015C is supplied with an external ±12 V power supply. Before connecting
the power supply to the mains make sure that the RED Line Voltage Switch on the Power Supply Module is set
to the proper voltage range so that it agrees with your local mains supply voltage. The PDA015C should
always be powered up using the power switch on the power supply or the PDA015C itself. Hot plugging the
unit is not recommended.
Covers and Service: Do not remove the cover of the PDA015C. There are no user serviceable parts in this
product. Refer servicing to qualified personnel. Do not cover the device in order to prevent overheating of
the instrument.
Explosive Environments: Do NOT operate this device in explosive environments.

Please read the Operational Precautions on the other side of this sheet

January26,2017
TTN122711‐D04,RevA
www.thorlabs.com/contact
Operational Precautions
ESD Sensitivity: The components inside the PDA015C(/M) are ESD sensitive. Take all appropriate
precautions to discharge personnel and equipment before making any electrical connections to the unit.
Shielded Connections: The PDA015C must be operated with proper shielded connection cables. Attach a
50 BNC-type coaxial cable (i.e. RG-58U) to the output of the PDA015C. For best performance, we
recommend terminating the cable with a 50 load at the measurement instrument. If the instrument has a
high impedance input, then adding an external 50 load resistor may be an option. Do not add an external
50 resistor if the instrument has an internal 50 termination, as the resulting 25 load could damage the
output of the PDA015C.
Electromagnetic Interference: Mobile telephones, cellular phones or other radio transmitters are not to be
used within the range of 3 meters of this unit since the electromagnetic field intensity may then exceed the
maximum allowed disturbance values according to IEC 61326-1.This product has been tested and found to
comply with the limits according to IEC 61326-1 for using connection cables shorter than 3 meters (9.8 feet).
Powering On: Note that immediately after the power is switched on, the output of the PDA015C will
momentarily (for 200 ms) go to its maximum output voltage (5 V for 50 load or 10 V for high impedance
load). For sensitive equipment that cannot tolerate this brief spike, turn on the PDA015C before connecting
to its output.
Input Optical Power: Photodiodes are sensitive devices and can be easily damaged by overpowering them;
care must be taken to ensure functionality. Be careful not to illuminate to photodiode beyond its 150 µm
diameter as this can degrade performance. Optical power can be converted to voltage using the formula
noted below. Please use the formula to ensure the detector is not saturated.
Voltage (V) = Optical Power (W) x Responsivity (A/W) x 50,000 (V/A) x (RLOAD / (RLOAD + 50 Ω))
The maximum output of the PDA015C is 5 V for 50 loads and 10 V for high impedance loads. Be sure not to
exceed these output levels to avoid signal distortion. If necessary, use neutral density filters to reduce the
input light level.
Caution Using Fiber Adapters: ThePDA015C was designed to allow maximum accessibility to the
photodetector by having the front surface of the diode close to the outside of the PDA015C’s housing. When
using fiber adapters, make sure that the fiber ferrule does not crash into the detector. Failure to do so may
cause dama
g
e to the diode and/or the fiber.
Manufactured by: Thorlabs Inc., 110 Parkland Plaza, Ann Arbor, MI 48103 USA
EU Importer: Thorlabs GmbH, Hans-Boeckler-Str.6, Dachau, D-85521 Germany