THUNDER TIGER TITAN X50 - User manual

INSTRUCTION MANUAL
組裝說明書
INSTRUCTION MANUAL
組裝說明書
This radio control model is not a toy! Before beginning assembly, please read
this manual thoroughly.
本產品為高性能模型非一般玩具，組裝與操作前請詳閱本產品說明書。
The contents are subject to change without prior notice due to product
improvements and specification changes.
本套件所附之零件可能跟圖示有所差異。因產品後續之設計研發或功能不斷改善之原
因，我們將保留產品規格變更權力，不再另行通知使用者。
No.4756 / 4757
Electric Version
No.4756
No.4757
All manuals and user guides at all-guides.com
all-guides.com

-1-
CONTENTS
INTRODUCTION
INTRO & CAUTION / 簡介與注意事項
OTHER ITEMS REQUIRED / 其餘必須配件
MANUAL FORMAT / 說明書使用方式
ASSEMBLY / 組裝步驟
Main Rotor / 主旋翼機構組裝
Main Rotor System-Flybarless / 主旋翼機構組裝-無平衡翼
Main Rotor Head Linkage Rod Installation / 主旋翼頭連桿組裝
Tail Boom Bracket Assembly / 尾管固定座組裝
Main Frame / 本體組裝
Landing Skid / 腳架組組裝
Main Gear Set / 主齒輪組裝
Control Arm Set / 控制臂組裝
Tail Rotor System / 尾旋翼機構組裝
Tail Unit / 尾部總成組裝
Servo Installation / 伺服機裝配
Linkage Rod Installation / 連桿組裝
Power Motor Installation / 動力馬達安裝
Electric Device Installation / 電子設備配置
Main Rotor Blade / 主旋翼安裝
SET-UP SECTION / 設定程序說明
Radio System Setup / 遙控系統設定
Swashplate Type Setting / 十字盤模式設定
Electric Device Connection / 電子設備連接說明
Index of Linkage Length / 連桿長度索引
Swashplate & Servo Movement Setting / 十字盤及伺服機動作設定
Tail Control And Gyro Setup 尾舵控制及陀螺儀控制
Setting Up Data For Your Reference 參數設定參考
Blade Tracking Adjustment / 主旋翼軌跡調整
Cautions of Li-Po Battery Pack Using / 鋰聚電池使用注意事項
After Flight Checklist / 飛行後的檢查項目
Regular Maintenance / 定期保養事項
SPARE PARTS / 零件包
SPARE PARTS LIST / 零件包表格
OPTIONAL PARTS / 改裝零件表
Exploded View / 爆炸圖檢索
2
4
5
6
10
11
12
13
15
16
17
18
20
21
22
23
24
25
26
26
26
27
27
28
29
30
31
31
31
32
37
44
45
Electric Version
All manuals and user guides at all-guides.com

-2-
INTRODUCTION / 簡介
Thank you for purchasing the Thunder Tiger Titan X50 R/C helicopter. This new helicopter is the latest
innovation by Thunder Tiger. It has the perfect combination of flying stability and the agility for 3D flying.
This helicopter is an excellent choice for flying enthusiasts like you. For convenient assembly and safe
operation of the helicopter, please read the instructions carefully. Retain the user manual in case you need
it for any information or reference.
感謝您購買雷虎科技Titan X50直昇機產品，本項產品為雷虎科技全新開發機種，兼具高度穩定性與3D飛行特性，是
熱衷引擎直昇機的您不可錯過的選擇。請於使用本產品前詳盡閱讀使用手冊，以利於組裝工作順暢進行與安全操控本
產品。請妥善保存使用說明書，以利後續調整與維修參考用途。
CAUTION / 警告
1. R/C models are not toys. This product is a high-precision flying machine. Possibilities of unexpected
crashes may occur due to electronic interference, incorrect operation, or poor mechanical maintenance.
Although it is a small-sized helicopter, the rotor blades rotate at high speeds, which may cause serious
damage, injury, or death if the model hits people or property. Therefore, extreme caution must be
exercised during operation.
2. Thunder Tiger ensures parts packaged in this product is of the highest quality. However, after assembly
and usage, parts damaged due to wear or misuse will not be replaced under any circumstances. If you
have any questions regarding its operation and repair, Thunder Tigers service agents are able to
provide free technical guidance.
3. This product is only recommended for users ages 16 and up. Because flying a R/C helicopter is difficult,
beginners must receive guidance and supervision from experienced pilots to minimize unexpected danger.
Practice in spacious areas, far away from obstacles such as buildings, trees, electrical towers, or crowds.
4. To decrease the cost of repair and maintenance for beginners, it is recommended to fly the helicopter
with a practice rack and to learn basic flying skills with a computer R/C flying simulator. (Crashes in
simulators are free to repair!)
1. 本項遙控直昇機產品並不是玩具，是一項結構精密、高專業度模型產品，如果未經正確組裝與操控，將可能對操控
者或其他人造成身體傷害。使用者必須了解，若未確實進行飛行前安全檢查或操控不當，而造成人員受傷或物體損
壞，使用者必須負起法律責任。
2. 本產品由高品質零組件組成，雷虎科技對於安裝過程、使用過後..等人為因素造成損壞事件不負損壞賠償之責。如您
需要本產品相關組裝、調整或其他協助，可與雷虎科技全省經銷商聯繫。
3. 本項產品禁止十六歲以下青少年與孩童使用。強烈建議初學者應取得技術支援後再進行飛行，以避免危險發生。請
於空曠地區操控本產品，並避免於建築物、樹木、電塔..等障礙物區域飛行。
4. 建議初學者可安裝練習架或透過電腦模擬軟體練習，可達到實際練習效果與符合經濟效益。
AMA INFORMATION / 特別注意事項
Operating a model helicopter requires a high degree of responsibility and skill. If you are a newcomer to the
hobby, it is best to seek help and guidance from accomplished model helicopter pilots. This will greatly
speed up the learning process and have you flying successfully in a reasonable amount of time. We also
would strongly urge you to join the Academy of Model Aeronautics. The AMA is a non-profit organization
that provides its members with a liability insurance plan as well as monthly magazine entitled Model Aviation.
All AMA charter aircraft clubs require all pilots to hold a current AMA sporting license prior to operation of
their models at club fields. For further information, contact the AMA at:
Academy of Model Aeronautics
5151 East Memorial Drive
Muncie, IN 47302
[phone]
操控遙控直昇機對於飛行安全要求極高，需要高度的負責任態度配合，以及較高的操控技巧。如果您是一位初學者，
建議您必須向當地專業模型經銷商，或是遙控直昇機相關組織以及經驗豐富的玩家尋求相關協助，以獲得您所需要的
訊息以及專業知識。如此可有效協助您縮短學習的時間，更容易學會遙控直昇機的組裝、設定與操控技巧。
All manuals and user guides at all-guides.com

-3-
FLIGHT SAFETY CHECKLIST / 飛行前安全確認工作項目
POST FLIGHT INSPECTION / 飛行結束安全檢查事項
CAUTION / 注意事項
1. Make sure that the transmitter battery is fully charged before flying.
2. Make sure all control surfaces are operated properly before flying.
3. Do a range check of the radio before the first flight. The electronic equipment must operate properly
at a range of at least 5 meters (18 ft) even with the transmitter antenna collapsed.
4. Make sure there are no other pilots using the same radio frequency with yours and that there are no
other radio interference on your frequency.
5. Be sure to turn on the transmitter first with the throttle stick in the idle position. Plug the battery into the
ESC last.
6. The main rotor and the tail rotor spin at very high RPM. Make sure nothing can come in contact with
the rotor blades during flight.
7. Always maintain a safe distance from the helicopter during flight.
8. Never fly the helicopter in the rain or in excessive wind conditions.
9. Always operate and fly the helicopter in a safe and responsible manner.
10. Never fly the helicopter over other pilots, spectators, cars or anything that could result in injury or
property damage.
1. 確認接收機與發射機電池，均已確實充電完成。
2. 確認所有操控介面運作順暢。
3. 確認無其他無線電波干擾，且不與其他同好同時使用相同頻率。
4. 確實將油門搖桿放置於低速，再將發射機電源開啟，然後再將電池接上。
5. 確認遙控器發射器與接收機工作正常，將機體放至於距離5公尺外，確認遙控器是否正常，機體控制動作是否正確。
6. 主旋翼與尾旋翼轉速相當高，運轉時須避免任何障礙物與旋翼接觸。
7. 飛行時，需與遙控直升機保持安全距離。
8. 勿於下雨天或是強風的狀態下操控遙控直升機。
9. 請以安全為第一考量，並以高度負責任的態度參與遙控直升機活動。
10. 禁止於人群、車輛..或任何其他障礙物上方飛行遙控直升機，避免意外發生。
1. Inspect the model thoroughly to insure no parts have come loose or become damaged during the flight
and landing. Replace damaged parts and tighten loose screws before flying again.
2. Clean the helicopter body.
3. Lubricate all moving parts to ensure smooth operation for the next flying.
4. Replace any worn ball links and damaged bearings.
5. Store the model in a cool, dry place. Avoid putting it under direct sunlight or near a source of heat.
Following these simple rules will allow you to enjoy the thrill of model helicopter flying for many years.
1. 飛行結束後確認機體所有的零件與螺絲是否有損壞或鬆動，更換損壞零件與確實固定鬆動的螺絲。
2. 機體清潔乾淨。
3. 檢查所有活動零組件是否運作順暢，以利下次飛行。
4. 更換所有鬆動的連桿、接頭，以及損壞的軸承。
5. 將機體存放於陰涼通風處，避免機體放置於陽光直射處或接近熱源。
確實執行上述幾項簡單的步驟，將可確保您的愛機維持數年的壽命！
When the model has crashed, inspect the flybar, rotor shaft and the blade spindle to make sure they are
not bent. If any item is damaged, it must be replaced with a new part to ensure safe operation. Do not
glue any broken or damaged plastic parts. Do not repair broken rotor blades. It is very important to
inspect the motor, speed control and the battery.
Always inspect the following items:
Gears, Ball links, Link rods, Bearings, Main shaft, Flybar, Spindle, Tail boom and support, Fins, Tail rotor
shaft, Belt, Main blades, Tail blades, the Motor, the Speed control and the Battery.
機體一但發生墜落事件，請確實檢查平衡桿、主軸、橫軸是否有彎曲變形，如果有任何的損壞，請立即更換原廠新
的零組件，確認機體操作安全！切勿使用任何接著劑嘗試黏合塑膠零件；請勿使用修復過的主旋翼。馬達、速控器
、電池的安全檢查工作亦相當重要。
發生機體墜落事件後，請確實檢查下列項目：
齒輪組、球頭連桿、連桿頭、軸承、主軸、橫軸、尾軸、平衡桿、平衡片、尾管、尾管支撐架、垂直與水平尾翼、
尾驅動輪、皮帶、主旋翼、尾旋翼、馬達、速控器、電池。
All manuals and user guides at all-guides.com

-4-
Screw Driver
各種規格的螺絲起子
Foam
雙面膠帶
OTHER ITEMS REQUIRED 需自行準備的配件
TOOLS REQUIRED FOR ASSEMBLY 需要準備的工具
Receiver
接收機
Battery 接收機電池
1000mAh
Gyro
發射機（需具備直昇機控制功能
的6動以上遙控器）
陀螺儀
RADIO SET / 遙控系統
POWER SYSTEM / 動力系統
7mm
5.5mm
7mm
8mm
Transmitter (helicopter type
only, 6 or more channels)
Switch Harness
具備充電線的開關組
Servo
伺服機
Hobby Knife
美工刀
C.A Glue
瞬間膠
Grease
潤滑油
Epoxy
環氧樹酯
Hex Wrench
六角板手
Threadlocker
螺絲防鬆膠
Needle Nose Pliers
尖嘴鉗
Wrench
開口板手
5.5mm
Ball Link Pliers
拆連桿頭的專用鉗子
Nipper
斜口鉗
Scissors
剪刀
Metric 4-way Wrench
十字套筒板手
5.5mm
7mm
8mm
10mm
Socket Drivers
套筒螺絲起子
Electric Brushless Motor
無刷馬達
Electronic Speed Controller
速控器 8~12S Li-Po Battery Pack
鋰聚電池組
All manuals and user guides at all-guides.com

-5-
Apply C.A Glue
使用快乾膠黏合
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble in right order
依標示順序組裝
Drill holes with the specified diameter
依標示尺寸鑽孔
Hint
組裝提示
Must be purchased separately
改裝品需另購
Cut off shaded portion
依標示部分裁切
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Apply grease
使用潤滑油膏(黃油)
Apply threadlocker
使用螺絲防鬆膠
The parts in the KIT are packed according to each major assembly steps. The part number and quantity are always
shown in the square box on each page. As good practice, only open up the bag that you need for the paticular assembly.
零件均依照組裝步驟包裝，請依照組裝程序，逐一開啟零件包，避免零件遺失。
T22(#262) THREADLOCKER / 螺絲防鬆膠
CA CA GLUE / 快乾膠
Note / 注意
Assembly drawings will contain icons that indicate use of
Threadlocker or CA glue as needed.
Examples of the icons are as right shown:
請依組裝步驟圖示，使用防鬆膠或接著劑。
圖示範例如右：
MANUAL FORMAT / 說明書使用方式
SYMBOLS USED THROUGHOUT THE MANUAL / 符號說明
How to read the instruction manual?
說明書導讀
A: Indicates the assembly step number and the parts bags
that are to be assembled.
B: Displays actual size drawings, and part quantities used.
C: All parts, except screws, are identified by its order
numbers. When purchasing spare parts, identify the part
required and cross reference this to the spare parts list in
the end of this maunal, which shows the purchasable
spare parts and the corresponding order numbers.
D: This instruction manual uses several symbols. Pay careful
attention to them during construction. Details are given
at the bottom of each page.
E: If a label marked here indicates the page is the exclusive
assembly steps for a particular model type; please follow
the exclusive instructions according to the model type you
purchased.
A: 顯示組立步驟及需組立之零件包順序。
B: 零件實際對照尺寸及使用數量。
C: 請比對零件形狀以及後附零件料號對照圖示找出需求零件料號。
D: 操作說明符號可更有效協助組裝者使用此說明書，請依說明書符
號指示進行組裝步驟。
E: 出現此標籤表示本頁為特定模型版本之專屬組裝說明，請依您所
購買之版本依說明進行組裝步驟。
Example 說明範例
CB
A
B
E
DC
All manuals and user guides at all-guides.com
all-guides.com

-6-
BK0649-1
LINKAGE BALL(A)
內六角連接頭螺絲(A)
BK0077
COLLAR,d3xD4xW6
軸環,d3xD4xW6
Assemble left and right side the same way
左右側組件相同
LR
LR
(8)
(4)
(9)
(7)
Secure the Linkage Balls to the Mixing Lever.
依圖示，安裝控制臂球頭，並適量使用螺
絲防鬆劑。
No.
1
2
3
4
5
QtyMaterial No. Description
HSA3-10
BUTTON HEAD SOCKET SCREW,M3x10
半圓頭內六角螺絲,M3x10
HMC25-8B
SOCKET SCREW,M2.5×8
內六角螺絲,M2.5×8
BK2187
COLLAR,d3xD4xW3.8
軸環,d3xD4xW3.8
名稱 No.
6
7
8
9
QtyMaterial No. Description 名稱
Note the orientation of the Chamfer
on the Metal Seesaw Hub.
注意金屬穩定固定座倒角方向。
(1)
(2)
(4)
(5)
(6)
(3)
Completed View
組裝完成
chamfer
倒角
chamfer
倒角
Apply threadlocker
使用螺絲防鬆膠
BV2181
BV2186
BK2187
HSA3-10
HMC25-8B
BK2182
BV2183
BK0649-1
BK0077
金屬主旋翼固定座
金屬穩定桿固定座
軸環,d3xD4xW3.8
半圓頭內六角螺絲,M3x10
內六角螺絲,M2.5×8
金屬旋翼頭制動器
金屬混控臂
內六角連接頭螺絲(A)
軸環,d3xD4xW6
METAL MAIN ROTOR HUB
METAL SEESAW HUB
COLLAR,d3xD4xW3.8
BUTTON HEAD SOCKET SCREW,M3x10
SOCKET SCREW,M2.5×8
METAL HEAD BUTTON
METAL MIXING LEVER
LINKAGE BALL(A)
COLLAR,d3xD4xW6
1
1
2
4
1
1
2
4
2
Main Rotor System / 主旋翼機構組裝
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Secure all screws shown on this page with a drop of thredlocker except the screws #7.
除螺絲＃7之外，本頁顯示之螺絲請使用適量防鬆膠鎖固。
Please skip to page 10 directly if the model you purchased is a flybarless edition.
如您購買的是無平衡翼版本，請直接翻至第10頁進行組裝。
Bag A
All manuals and user guides at all-guides.com

-7-
Main Rotor System / 主旋翼機構組裝
Bag B
HME3-10B
SET SCREW,M3x10
無頭內六角螺絲,M3x10
BK0649-1
LINKAGE BALL(A)
內六角連接頭螺絲(A)
HMC2510B
SOCKET SCREW,M2.5×10
內六角螺絲,M2.5×10
Thread the Paddles onto the Flybar Rod, equal the
length to the Flybar Control Arms of each side.
旋上穩定翼於穩定翼桿上，確認兩側的穩定翼至控制臂
距離相等。
Line up the Paddles with the Flybar Control Arms.
對正穩定翼與穩定翼控制臂呈水平狀態。
Ensure the leading edges of the Paddles are
toward the same side to the Metal Flybar Control
Posts.
確認穩定翼前緣與穩定翼控制轉臂方向相同。
No.
1
2
3
4
QtyMaterial No. Description 名稱 No.
5
6
7
8
QtyMaterial No. Description 名稱
(1)
(6)
(8)
(7)
(7)
(8)
(3)
(4)
139.5mm
139.5mm
110mm 110mm
116mm
HME4-5B
SET SCREW,M4x5
無頭內六角螺絲,M4x5
(2)
BK2184
BK2185
HMC2510B
BK0649-1
HME4-5B
BK0631
HME3-10B
BK0067B
無頭內六角螺絲, M4x5
穩定桿
無頭內六角螺絲,M3x10
穩定翼(黑), 20G
金屬穩定翼轉臂
金屬穩定翼轉臂支柱
內六角螺絲, M2.5×10
內六角連接頭螺絲(A)
SET SCREW, M4x5
SUS FLYBAR
SET SCREW,M3x10
FLYBAR PADDLE(BLACK), 20G
METAL FLYBAR CONTROL ARM
METAL FLYBAR CONTROL ARM POST
SOCKET SCREW, M2.5×10
LINKAGE BALL(A)
2
2
2
2
2
1
2
2
Secure all screws shown on this page with a drop of thredlocker except the screws #7.
除螺絲＃7之外，本頁顯示之螺絲請使用適量防鬆膠鎖固。
LR
Line up the hole of the Flybar Control Arm
and the flat spot of the Flybar Rod when
securing the screw.
安裝平衡桿時，請確認對正穩定翼控制臂上鎖
固孔位與平衡桿上平面凹槽。
Assemble left and right side the same way
左右側組件相同
LREnsure smooth, non-binding movement when assembling
確認組件靈活度
Apply threadlocker
使用螺絲防鬆膠
Apply C.A Glue
使用快乾膠黏合
(5)
(4)
All manuals and user guides at all-guides.com

-8-
Main Rotor System / 主旋翼機構組裝
Bag B
Large Internal
Diameter
always go toward the
Main Rotor Hub
內徑較大的一側，面向
主旋翼中心座組。（內
側）
Small Internal
Diameter
always go toward the
Blade
內徑較小的一側，面向
主旋翼組（外側）。
HMV1370ZZWY
BEARING,d7xD13xW5
滾珠軸承,d7xD13xW5
BK2216
THRUST WASHER,d10xD13xW0.5
止推墊片,d10xD13xW0.5
HMX0612
THRUST BEARING,d6xD12xW4.5
止推軸承,d6xD12xW4.5
BK2525
FLAP COLLAR,d7xD10xW1.5
避震軸環,d7xD10xW1.5
HMC4-8B
SOCKET SCREW M4×8
內六角螺絲M4×8
Apply threadlocker
使用螺絲防鬆膠
Completed View
組裝完成
Assemble left and right side the same way
左右側組件相同
LR
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Checking Tips: >
轉動角度： >
（轉動角度大者，內孔大；轉動角度小者，內孔小）
No.
1
2
3
4
5
6
7
8
Qty
2
2
2
2
2
4
2
2
Material No. Description 名稱 No.
9
10
11
12
13
14
15
QtyMaterial No. Description 名稱
(10)
(9)
(11)
(13)
(14)
(6)
(1)
(5) (3) (2)
(6)
(4)
Diagram for Thrust Bearing Assembly
止推軸承安裝示意圖
(12)
(7)(15)(15) (8)
Apply grease
使用潤滑油膏(黃油)
BV2574
BK2579
BK2578
HMC3-8B
BK0649-1
HSA3-6
BK2216
HMX0612
BK2214
BK2573
BK2572
BK2525
BK0435
HMC4-8B
HMV1370ZZWY
金屬旋翼轉座組
金屬轉座擺臂
金屬連接座
內六角螺絲, M3×8
內六角連接頭螺絲(A)
半圓頭內六角螺絲, M3x6
止推墊片, d10xD13xW0.5
止推軸承,d6xD12xW4.5
強化固定軸(D7)
外避震墊圈, 7mm
內避震墊圈,7mm
避震軸環,d7xD10xW1.5
墊圈,d4xD11xW1.7
內六角螺絲M4×8
滾珠軸承, d7xD13xW5
METAL MAIN ROTOR GRIP SET
METAL ROTOR GRIP LEVER
METAL ROTOR GRIP POST
SOCKET SCREW, M3×8
LINKAGE BALL(A)
BUTTON HEAD SOCKET SCREW, M3X6
THRUST WASHER, d10xD13xW0.5
THRUST BEARING,d6xD12xW4.5
HARDENED FEATHERING SHAFT
OUTER DAMPER, 7mm
INNER DAMPER, 7mm
FLAP COLLAR,d7xD10xW1.5
WASHER,d4xD11xW1.7
SOCKET SCREW M4×8
BEARING, d7xD13xW5
1
2
2
2
2
2
4
Assemble the main rotor pitch housing as drawing
主旋翼轉座組裝示意圖
The bearings (#15) come with the grips which
had been assembled by Factory.
主旋翼夾座內軸承 (#15) 已由原廠壓配完成。
HMC3-10B
SOCKET SCREW,M3x10
內六角螺絲,M3x10
BK0649-1
LINKAGE BALL(A)
內六角連接頭螺絲(A)
HSA3-6
BUTTON HEAD SOCKET SCREW,M3x6
半圓頭內六角螺絲,M3x6
BK0435
WASHER,d4xD11xW1.7
墊圈,d4xD11xW1.7
Secure all screws shown on this page with a drop of thredlocker.
本頁顯示之螺絲請使用適量防鬆膠鎖固。
Apply some amount of silicon oil or
Vaseline on the Spindle for easy
assembly.
在橫軸上塗抹此許矽膠油脂或凡士林可使
組裝更為容易。
LR
All manuals and user guides at all-guides.com

-9-
Main Rotor System / 主旋翼機構組裝
Bag B
HMM3Z
NYLON NUT,M3
止鬆螺帽,M3
BK0616
SOCKET SCREW,M3x20
內六角螺絲(半牙),M3x20
HMS15
E RING
E型扣環
HMV740ZZY
BEARING,d4xD7xW2.5
滾珠軸承,d4xD7xW2.5
HSA3-10
BUTTON HEAD SOCKET SCREW,M3x10
半圓頭內六角螺絲,M3x10
BK0077
COLLAR,d3xD4xW6
軸環,d3xD4xW6
BK0088
WASHER,d3xD5xW0.5
墊片,d3xD5xW0.5
(12)
(10)
(6)
(14)
(13)
(9)
(1)
(3)
(2)
(7)
(5)
(4)
(8) (8)
BK0649-1
LINKAGE BALL(A)
內六角連接頭螺絲(A)
LR
Assemble left and right side the same way
左右側組件相同
LR
No.
1
2
3
4
5
6
7
QtyMaterial No. Description 名稱 No.
8
9
10
11
12
13
14
QtyMaterial No. Description 名稱
The holes should point up.
請注意，有孔位的一端應朝上
Apply threadlocker
使用螺絲防鬆膠
BK2277
BK0616
HMM3Z
BV2188A
BK2196
BK2199
BK0016-1
HMV740ZZY
BK0171
HMS15
BK0649-1
BK0088
BK0077
HSA3-10
強化主軸
內六角螺絲(半牙),M3x20
止鬆螺帽,M3
金屬十字盤組
控制臂座
金屬穩定翼控制臂
連接座
滾珠軸承, d4xD7xW2.5
插銷
E型扣環
內六角連接頭螺絲(A)
墊片 d3xD5xW0.5
軸環, d3xD4xW6
半圓頭內六角螺絲, M3x10
HARDENED MAIN SHAFT
SOCKET SCREW,M3x20
NYLON NUT,M3
METAL SWASHPLATE
METAL WASHOUT BASE
METAL FLYBAR CONTROL LEVER
WASHOUT LINKAGE
BEARING, d4xD7xW2.5
PIN
E RING
LINKAGE BALL(A)
WASHER, d3xD5xW0.5
COLLAR, d3xD4xW6
BUTTON HEAD SOCKET SCREW, M3x10
1
2
2
1
1
2
2
4
2
2
2
2
2
2
(11)
BK0171
PIN
插銷
Secure all screws shown on this page with a drop of thredlocker.
本頁顯示之螺絲請使用適量防鬆膠鎖固。
All manuals and user guides at all-guides.com