Timotion TDH18P User manual

Hand Control Programming-TDH18P
Version 2 July 2019
1 of 11
1
20190731
User Manual
Hand Control
Programming-
TDH18P

Hand Control Programming-TDH18P
Version 2 July 2019
2 of 11
2
Contents
Contents .....................................................................................................................................................................2
Disclaimer ..................................................................................................................................................................3
1. User Interface Guide.............................................................................................................................................4
2. Reset....................................................................................................................................................................5
3. Adjusting the Height.............................................................................................................................................6
4. Setting the Memorized Position ...........................................................................................................................6
5. Setting the Upper and Lower Height Limit ............................................................................................................7
6. Presetting the Desk Starting Height .....................................................................................................................8
7. Lock / Unlock .......................................................................................................................................................8
8. Switching Metric and Imperial Unit .......................................................................................................................9
9. Error Codes ........................................................................................................................................................10
10. Power Saving Function - Waking Up the Control .................................................................................................11

Hand Control Programming-TDH18P
Version 2 July 2019
3 of 11
3
Disclaimer
This user manual is ONLY for generic TiMOTION products. Manufacturers may have altered settings causing
them to differ from this user manual. Please contact the manufacturer for a revised manual if the product
settings are different than this manual.

Hand Control Programming-TDH18P
Version 2 July 2019
4 of 11
4
1.User Interface Guide
*USB charging ports: For charging electronic devices
3-digit height display
USB charging ports*
Up and down buttons
Safety lock button
Memory setting buttons

Hand Control Programming-TDH18P
Version 2 July 2019
5 of 11
5
2.Reset
1. Simultaneously press and for 3 seconds. Continue pressing the buttons until both columns are
in lowest position. When finished with the reset, the control box makes a beep sound and the buttons
can be released.
2. When finished with the reset, the display will show starting height.
3. Users must conduct a reset when the desk is operated for the first time.

Hand Control Programming-TDH18P
Version 2 July 2019
6 of 11
6
3.Adjusting the Height
Press or button until the desk reaches the preferred height.
4.Setting the Memorized Position
TDH18P supports a maximum of 2 memory positions.
How to memorize position:
1. Adjust the desk to the desired height.
2. Press the preferred memory button (1 or 2), with either or for 2 seconds. Once the display
shows P1 or P2, the position is memorized.
3. Press (and hold) button 1 or 2 to move the desk to memorized position. (Note 1)
Note 1: It depends on the control box setting whether the memory button needs to be held or not.

Hand Control Programming-TDH18P
Version 2 July 2019
7 of 11
7
5.Setting the Upper and Lower Height Limit
A. Setting the upper height limit:
(1) Adjust the desk to the preferred upper height limit.
(2) Press and buttons together less than 3 seconds, holding and release button. (Note 2)
(3) Re-press for more than 3 times in a slow pace.
(4) A beeping sound will notify you that the process has completed.
B. Disable the upper height limit:
(1) Move the desk to the upper height limit that is being set.
(2) Repeat the instruction #2~4 above to disable the upper limit setting.
C. Setting the lower height limit:
(1) Adjust the desk to the preferred lower height limit.
(2) Press and buttons together less than 3 seconds, holding and release button. (Note 3)
(3) Re-press for more than 3 times in a slow pace.
(4) A beeping sound will notify you that the process has completed.
D. Disable the lower height limit:
(1) Move the desk to the lower height limit that is being set.
(2) Repeat the instruction #2~4 above to disable the lower limit setting.
Note 2: Some control boxes may not support setting the upper and lower height limit functionality.
Note 3: Over 3 seconds will direct to “Reset”mode.

Hand Control Programming-TDH18P
Version 2 July 2019
8 of 11
8
6.Presetting the Desk Starting Height
(1) Press button until the desk reaches its lowest position and then release button. Re-press
button again for 5 seconds and the digital display will flash for 10 seconds.
(2) Adjust the starting height number with the or button.
(3) After 10 seconds, the display will stop flashing and this will confirm that you have successfully set the
starting height.
7. Lock / Unlock
(1) Lock: Press the “lock” button for one second or do not touch any buttons for 20 seconds, then the image
will be shown on the display to indicate that the lock was completed successfully (as below image).
(2) Unlock: Hold the “lock” button for 3 seconds to unlock the hand control.

Hand Control Programming-TDH18P
Version 2 July 2019
9 of 11
9
8.Switching Metric and Imperial Unit
(1) Press memory button 1, 2 and Lock button for 5 seconds.
(2) The digital display will show “C-I”. If there is no further instruction operated within 5 seconds, the system
will go to the normal operation mode.
How to choose a metric unit
Press the button 1, the digital display will show “C”to stand for centimeter.
How to choose an imperial unit
Press the button 2, the digital display will show “I”to stand for inch.

Hand Control Programming-TDH18P
Version 2 July 2019
10 of 11
10
9.Error Codes
The digital display shows the error codes below to suggest the issues that users may encounter during the
operation. (Note 4)
Error code
Descriptions
000
Resetting
E00
Not reset completely
E01
Overuse protection
E02
Unbalance protection
E03
Anti-collision
E04
T-touch Protection
E11
M1 Motor over-current protection
E12
M2 Motor over-current protection
E13
M3 Motor over-current protection
E21
No Hall sensor from M1
E22
No Hall sensor from M2
E23
No Hall sensor from M3
E31
No current from M1
E32
No current from M2
E33
No current from M3
Note 4: Some control box may not support this function.

Hand Control Programming-TDH18P
Version 2 July 2019
11 of 11
11
10. Power Saving Function - Waking Up the
Control
If no buttons have been pressed for 25 seconds, display goes off. Press any button to light up the
display again.
If no buttons have been pressed for 30 seconds, the system goes to <0.1W standby mode. (Note 5) Long
press any button to wake the system up. The digital display will show desk height again.
Note 5: It depends on the control box whether it support 0.1W standby mode or not.