Titanium TRL-10R Kit User manual

Product Code: 88110 REVISION 2020.1.0
Instruction Manual
TRL-10R Kit
RED ROTARY LASER

2

3
EN
Read the following safety instructions before attempting to
operate this tool.
Keep these instructions in a safe place or store in the carry
case for future reference.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR
FUTURE REFERENCE.
WARNING!
Read and understand all instructions.
• Use the tool only with the specifically designated
batteries.
• Store the tool out of reach of children and other untrained
persons. Laser tools are dangerous in the hands of
untrained users.
• Use only accessories that are recommended for your
model.
• Tool service must be performed only by qualified repair
personnel. Repairs, service or maintenance performed
by unqualified personnel will void the warranty. Only
approved and authorised service technicians can carry
out warranty repairs.
• Do not use optical tools such as a telescope or transit to
view the laser beam. Serious eye injury could result.
• Do not place the tool in a position which may cause
anyone to intentionally or unintentionally stare into the
laser beam. Serious eye injury could result.
• Do not position the tool near a reflective surface which
may reflect the laser beam toward anyone’s eyes. Serious
eye injury could result.
• Do not use optical tools to view the laser beam.
• Do not set up the tool at a position where the laser beam
can cross any person at head height.
• Do not let children come in contact with the tool.
• Turn the tool off when it is not in use. Leaving the tool on
increases the risk of staring into the laser beam.
• Do not operate the tool around children or allow children
to operate the laser. Serious eye injury may result.
• Position the tool securely on a level surface. Damage to
the tool or serious injury could result if the tool falls.
• Do not remove or deface warning labels.
• If the text on the warning label is not in your native
language, cover it with the appropriate label supplied
before commencing operation of the laser.
WARNING!
Do Not Disassemble The Laser.
There are no user serviceable parts inside. Disassembling
the tool will void all warranties on the product. Do not modify
the product in any way. Modifying the tool may result in
hazardous laser radiation exposure.
CAUTION!
Class 2 Laser Product
• Never look into the laser beam directly and intentionally.
• Do not use optical tools to view the laser beam.
• Do not set up the tool at a position where the laser beam
can cross any person at head height.
• Do not let children come in contact with the laser.
!
!
!
INCHES CM
1
1
2
3
4
5
6
7
2
3
Please ensure the following items are included with your laser level. If anything is missing please contact your retailer.
1Titanium TRL-10R
2Remote control
3Detector & clamp
4Laser target
1
4
7
3
5
6
9
10
8
9 Adaptor head (UK)
10 Adaptor head (EU)
5 Laser glasses
6Hard carry case
7Rechargeable battery pack
8 Mains power /
indoor charger adaptor
SAFETY
ITEM CHECKLIST
MANU AL
GRADE TILT
ALARM
RPM
MANUAL
GRADE
2

4
EN
1 Rotating laser port
2 Protective lighthouse
3 Control panel
4 Rechargeable battery charging port
5 5/8” x 11 thread for horizontal
operation on a tripod
6 Battery thumb screw
7 Power button
8 Speed control button
9 Manual grade mode button
10 Tilt alarm button
11 X / Y axis indicator (manual grade mode)
X-axis = solid LED light
Y-axis = flashing LED light
12 Power indicator
13 Tilt alarm indicator
1
3
4
MANU AL
GRADE TI LT
ALARM
RPM
2
7
8
9 10
11
12
13
4
5
6
POWER SUPPLY
Rechargeable battery pack
• The laser level is supplied with a rechargeable
Ni-MH battery pack that is located in the base
of the laser level.
• The rechargeable battery pack is supplied only partially
charged. Charge the rechargeable battery pack before
use. Keep the rechargeable battery pack in the carry case
when not in the laser level.
• The power indicator light will flash when the battery is
low. The laser level should be re-charged as soon as
possible.
• Battery pack capacity decreases at low temperatures;
a depleted pack may not function when cold.
Indoor charger
• The indoor charger is for indoor use only.
• Do not store in locations where moisture can be present
or where the chargers could be exposed to extreme
temperatures.
• If a charger becomes damaged, stop using immediately
and seek a replacement.
LASER OVERVIEW
USING THE LASER
!
WARNING! Only use the supplied charger.
Using an incorrect charger will void the
warranty. Do not charge alkaline batteries.

5
EN
Fig. 1
!
i
i
i
Charging the rechargeable battery pack
• Attach the desired adaptor head onto the charger.
• Insert the charger into one of the two charging ports
(Fig.1). The charging ports are located on the battery
pack and underneath the control panel. Progress
will be shown by the power indicator display on the
charger as following:
Red (flashing) = Charger and battery
are not connected.
Red (constant) = Battery is charging
Green (constant) = Battery is charged
• Charging time is approximately 5 hours for
a depleted battery.
The battery pack does not need to be inserted in the
laser level whilst charging via the port on the battery
pack.
Removing and inserting the rechargeable battery pack
• Loosen the battery thumb screw on the base of
the laser level and remove the battery pack.
• Insert the battery pack, ensuring the metal pins
are aligned. Tighten the battery thumb screw.
WARNING! Do not attempt to
disassemble the battery pack.
HORIZONTAL MEASUREMENT SETUP
Level surface set up
• Select a place as close and practical to the work site as
possible, and ensure that the location is clear of traffic.
• Place the laser level onto a reasonably level surface
with the lighthouse facing upwards.
VERTICAL MEASUREMENT SETUP
Level surface set up
• Select a place as close and practical to the work site as
possible, and ensure that the location is clear of traffic.
• Place the laser level onto a reasonably level surface with
the control panel facing upwards.
OPERATION
Powering on
• Press the power button once and the laser level
will power on and begin automatically self-levelling.
When this levelling process is complete, the penta
prism inside the lighthouse will start rotating.
• If the laser level is outside the self levelling range the
laser level will not level causing the laser beam to flash
continuously. If this occurs, reposition the laser level onto
a level surface until the laser level can level off.
In bright outdoor conditions, visible distance will
besignicantlyreduced.Foroutdooruse,itis
recommended to use the included detector.
Powering off
• Press the power button once and the laser level
will power off.
Speed control
• Press the speed control button on the remote control
to cycle through various rotational speeds.
Sleep mode
• Press the sleep button on the remote control to
enter into sleep mode.
• The laser diode will stop spinning and shut off.
(The unit is not turned off in sleep mode).
• Press the sleep button on the remote control to exit
sleep mode.
After 60 minutes of inactivity during sleep mode,
the laser level will turn off automatically.
Tilt alarm
• Once the laser level has been levelled off the tilt alarm
can be enabled by pressing the tilt alarm button. The tilt
alarm indicator light will flash continuously whilst active.
• If the laser level is disturbed while the alarm is active the
laser level will stop rotating and will need to be powered
off and on again to reset to a level position.
USING THE LASER (continued)

6
EN
1 Manual grade mode button
2Grade adjustment
(manual mode) button
REMOTE CONTROL
DETECTOR & CLAMP
MANUAL
GRADE
REMOTE CONTROL OPERATION
Power supply
• The remote is powered by two AA alkaline batteries.
Battery replacement
• Remove the battery cover door and the batteries.
• Insert the batteries according to polarity and replace
the battery cover door.
Operating the remote control
• Ensure the laser level is turned on and the laser
head is rotating.
• Grade set-up function is done via the remote control.
To set up a manual grade / slope refer to page 6.
• For details on other remote control functions including
speed control and sleep mode, refer to page 5.
5
1
22
4
3
3Speed control button
4 Sleep mode button
5 Battery compartment
i
i
Setting up a manual grade / slope
• To create a manual grade / slope, press the manual
grade mode button on the laser level control panel or
remote control. The laser level will now be in manual
mode with the X-axis active. The LED X / Y axis indicator
on the laser control panel will display a solid light to
indicate X-axis is selected.
• Press the grade adjustment arrow buttons on the
remote control.
• To change to the Y-axis, press the manual grade mode
button. The LED X / Y axis indicator on the laser control
panel will flash to indicate the Y-axis is selected. The
laser level can now be adjusted on the Y-axis.
• Press the grade adjustment arrow buttons on the
remote control.
USING THE LASER (continued)
• To adjust the grade, press the manual grade mode
button to cycle between X and Y axis
• To cancel manual grade mode, and return to normal
levelling press the power button off and on again to
reset the levelling process.
When in manual mode the laser level will not self
level and correct for vibrations and/or disturbances.
Grade adjustments can only be made by
pressing the grade adjustment arrow buttons
on the remote control.
REMOTE CONTROL OVERVIEW
DETECTOR OVERVIEW
1 LED indicator
2Laser sensor
3LCD display screen
4 Power button
5 Screen backlight
1
2
3
4
6
5
7
8
9
10
6 Speaker on / off button
7 Detection mode button
8 Speaker
9Staff clamp mounting point
10 Battery compartment

7
EN
DETECTOR & CLAMP (continued)
DETECTOR LCD SCREEN OVERVIEW
1 Arrow indicator
2Detection mode
3Centre alignment
4 Brightness indicator
5 Battery indicator
6 Speaker indicator
12
4
6
5
3
POWER SUPPLY
• The detector is powered by one 9V alkaline battery.
Battery replacement
• Remove the battery cover door and the batteries.
• Insert the batteries according to polarity and replace
the battery cover door.
MOUNTING TO THE STAFF CLAMP
• Insert the staff clamp screw into the staff clamp
mounting point.
• Rotate the staff clamp thumb screw until the clamp
is secured in place.
DETECTOR OPERATION
• Power the detector on by pressing the power button.
The LCD screen will turn on and the speaker will emit
a small tone to indicate the detector is operating.
• The LCD screen will display the battery level,
detection mode and speaker function.
• To change between broad, coarse and fine mode
press the detection mode button.
• To change the speaker volume or turn the speaker
off, press the speaker button.
• To turn on the backlight, hold down the mode
button for approximately 3 seconds.
• Move the detector into the path of the laser beam.
• Hold the detector upright for horizontal beams (Fig. 2) or
rotate 90° for vertical beams (Fig.3).
• The direction arrows or level line on the LCD screen
will indicate the position of the laser beam. A digital
increment display will indicate the position of the laser
beam (Fig. 2 & 3). The detector will emit a constant beep
once the level position has been located (Fig. 4).
Fig. 2
Fig. 3
Fig. 4

8
EN
Error Cause & Solution
Laser does not turn on
• The battery pack may require charging or need to be replaced due to age and / or
a high number of charging cycles.
• Check the battery compartment for signs of damage and ensure that the
compartment is clean and that the battery terminals are not bent.
Laser does not remain on
for long periods of use.
• Check the battery pack. The battery pack may require charging or need to be
replaced due to age and/or a high number of charging cycles.
• Check the battery compartment for signs of damage and ensure that the
compartment is clean and that the battery terminals are not bent.
Laser does not level off
• The laser level may be outside of its levelling range and may require an adjustment
before self-levelling can commence.
• The laser level may have impact damage.
TROUBLE SHOOTING
MOUNTING TO A CONSTRUCTION TRIPOD
A construction tripod (flat, domed or elevating) can
be purchased from your nearest measurement tool
dealer. The below instructions are generic only and
set-up methods may vary between models. Refer to
the documentation from the tripod manufacturer for
details.
• Extend the tripod legs to the required height and ensure
the legs are spread wide enough so that the tripod
platform is stable. Secure the legs in place (refer to the
documentation from the tripod manufacturer for details).
i
!
NOT INCLUDED
• Place the laser level onto the tripod with the lighthouse
facing upwards and mount the male 5/8” thread into the
base until firm. Do not over tighten as this may cause
damage to the laser level or tripod.
• If using an elevating tripod with a measuring scale on the
centre column, the height can be adjusted as required.
WARNING! Attaching the laser level to a
tripod without the correct thread size may
cause damage.
CALIBRATION CHECK
Before doing any precision levelling it is advised
to check the calibration of the laser level.
• Set up the laser level on a tripod at about 30m
facing a wall or staff with a detector.
• Allow the laser to level.
• Detect and note laser position on the wall or staff.
CARE & MAINTENANCE
1. This is a precision measuring tool and should
always be handled with care and transported
within the carry case provided.
2. Always turn the laser level off when transporting
the laser level or moving around the job site.
3. Whenever possible, store the laser level in a dry,
shady location.
4. When the laser level is not in use or is being stored,
it is highly recommended to remove the batteries.
• Without moving the tripod, rotate the laser level 180°.
• Detect and note laser position on the wall or staff.
• Calculate the distance between the two readings.
• The difference should be within 6mm at 30m.
• If the laser level is out of calibration it is advised
to send it to an authorised service centre.
5. Calibration of the laser level is recommended: every
six months, if ongoing accurate levelling is required,
or an impact has occurred.
6. The operator should check the accuracy of the laser
level before precision levelling is attempted. Failure to do
so may result in inaccurate measurements.
7. Clean the laser level with a dry, soft cloth after
use in dusty, damp or wet conditions before storing.
8. Smudges and fingerprints may be removed
with a damp tissue or a soft, lint-free cloth.

9
EN
All Titanium measurement tools are carefully checked
and tested to our precise quality assurance standards.
We offer a warranty in accordance with
the following conditions:
1. Our warranty provides the correction of deficiencies
to the tool once verified by an authorised
service centre that the deficiencies were caused
by a manufacturing fault within the warranty period.
2. The standard warranty period is 3 years from
the date of purchase. The warranty period can be
extended to 7 years upon registration of the tool
within 30 days of purchase.
3. The warranty does not cover:
a) Calibrations and components that are subject
to wear and tear.
b) Defects in the tool caused by non-compliance with
the operation instructions, improper use, abnormal
environmental conditions, inappropriate operating
conditions or insufficient maintenance.
c) Defects caused by using accessories or spare
parts other than approved parts.
d) Services or repairs carried out by
non-authorised persons.
4. Defects recognised by an authorised service centre as
being covered by the warranty shall be corrected either
by repair or replacement of the tool.
5. The warranty claim must be lodged within the warranty
period. This requires the complete tool with the original
sales receipt containing the purchase date and place
of purchase. Partial or disassembled tools cannot be
submitted for a warranty claim.
6. Services provided under warranty do not
lengthen or renew the warranty of the tool.
The above guarantees apply to tools that are
purchased in the countries and regions specified
online at www.titaniumlaser.tools
3 YEAR STANDARD WARRANTY PERIOD
1. The warranty period for your tool is 3 years
from the date of purchase.
2. The warranty period for batteries, battery packs
and chargers is 1 year from the date of purchase.
3. Calibrations are not covered under warranty as
they are deemed wear and tear.
4. All products have a standard warranty period,
you do not have to register your products to obtain
the standard warranty period.
5. To claim under this warranty, the date of purchase
of the tool must be documented by an invoice/receipt.
WARRANTY
7 YEAR EXTENDED WARRANTY PERIOD
1. The extended warranty is available on selected tools only.
2. You may extend the warranty period for your tool (laser
level, optical level or laser distance measurer) to 7 years
from the date of purchase. Accessories are excluded
from the warranty extension and remain at the 3 year
warranty period.
3. The warranty period for batteries, battery packs and
chargers is 1 year from the date of purchase.
4. Calibrations are not covered under warranty as they
are deemed wear and tear.
5. To obtain the extended warranty, the registration
process must be completed within 30 days from
the date of purchase.
6. Failure to register your product online and/or submission
of a valid invoice/receipt will void the warranty extension.
7. Please ensure ALL information submitted/uploaded
is correct.
Extended warranty is ONLY available via online
registration, offline (mailing in of warranty registration)
will not be accepted.
Visit www.titaniumlaser.tools to register.
Battery pack will not charge or is
not lasting long in use
• Check the battery pack. The battery pack may require charging or need to be
replaced due to age and / or a high number of charging cycles.
• Check the battery compartment for signs of damage and ensure that the
compartment is clean and that the battery terminals are not bent.
Detector does not detect the
laser beam
• Check the batteries on the detector. They may be low and need replacing.
• Check the laser settings and ensure the laser is producing a beam.
• Check the line of sight and ensure there is no interference.
• Check that the laser level and detector are within the operating range.
TROUBLE SHOOTING (continued)

10
*With online registration (3 years without registration). Please refer to page 9 for details.
Specications TRL-10R
Product code 88110
Warranty 7 Years*
Accuracy ±1.5mm at 30m (±0/16in / 0.06in at 100ft)
Operating range 300m / 1600ft (diameter)
Levelling range ±9% / ±5°
Laser class 2 Red
Battery life 20 hours+
IP rating 65
Weight (kg) 2.38
Dimensions (mm) 210 x 157 x 200
SPECIFICATIONS
To assist you with any queries or technical
questions please contact customer support.
Australia: 1300 658 338
New Zealand: 0800 367 527
United Kingdom: 0808 189 1152
All other countries / regions:
Visit www.titaniumlaser.tools for more information
This device complies with all necessary standards for the
free movement of goods within the EU. This product is an
electric device and must be collected separately for disposal
according to the European Directive on waste electrical and
electronic equipment.
CUSTOMER SUPPORT EU DIRECTIVES & DISPOSAL
EN

11
EN
NOTES

© 2020. Titanium Laser Tools