TIYA 65050 User manual

Save This Manual for Future Reference
Original Instruction
Table Saw
Operator’s Manual
MODEL NUMBER : 65050
SERIAL NUMBER :
Both model number and serial number may be found on the main
label. You should record both of them in a safe place for future use.
FOR YOUR SAFETY
READ AND UNDERSTAND THE ENTIRE MANUAL BEFORE
OPERATING MACHINE
65050UK00M100.indd 1 2020/5/27 9:36:10

TABLE SAW
2
GB TABLE OF CONTENTS
INTRODUCTION
Introduction 2
Specifications 2
Symbols 3
Safety 3
General Safety Rules 3
Specific Safety Rules 4
Contents Supplied 8
Assembly 9
Know your Machine 13
Features & Controls 13
Set Up 14
Operation 14
Transport 17
Maintenance 17
Storage 18
Trouble Shooting 19
Parts Schedule 20
Parts List 21
Your new Table saw will more than satisfy
your expectations. It has been manufactured
under stringent quality standards to meet
superior performance criteria. You will find
it easy and safe to operate, and with proper
care, it will give you many years of dependable
service.
* S6 40%, 5 min, continuous operation periodic
duty: time of one load cycle is 5 minutes,
operation time at constant load is 2 minutes,
operation time at no-load is 3 minutes.
Carefully read through this entire
operator’s manual before using your
new Table saw. Take special care to
heed the cautions and warnings.
Specifications
Model Number 65050
AC Motor 230-240V ~ 50Hz
Power P 2000W (S6 40 % 5 min.)*
Blade Size Ø 250 ×Ø30 ×2.4 mm
Number of Saw Teeth 24
Cutting Capacity
73 mm @ 0°
53 mm @ 45°
Height Adjustment 0 - 73mm
Blade Tilt Adjustment 0°- 45°
Blade Speed 4200 /min
Standard Tabele Size 610×445 mm
Extension Table Size
610×250 mm /
445×320mm
Table Height 857 mm
Weight 23.5 kg
Sound pressure level (LPA) 96.2 db(A) k=3 db(A)
Sound power level (LWA) 109.2 db(A) k=3 db(A)
This table saw is designed for operating under
ambient temperatures between +5°C and
40°C and for installation at altitudes no more
than 1000m above M.S.L. The surrounding
humidity should less than 50% at 40°C. It
can be storedor transported under ambient
temperatures between -25°C and 55°C.
APPLICATION CONDITIONS
RECYCLING AND DISPOSAL
This marking indicates that this
product should not be disposed with
other household wastes. To prevent
possible harm to the environment
or human health from uncontrolled
waste disposal, recycle it responsibly
to promote the sustainable reuse of
material resources. To return your
used device, please use the return
and collection systems or check with
your local authority or local stores
for advice of environmental safe
recycling.
65050UK00M100.indd 2 2020/5/27 9:36:10

TABLE SAW 3
GB
SYMBOLS
The rating plate on your machine may
show symbols. These represent important
information about the product or instructions
on its use.
Read these instructions for use
carefully.
Caution! Wear ear-muffs. The
impact of noise can cause damage
to hearing.
Caution! Wear safety goggles.
Sparks generated during working
or splinters, chips and dust
emitted by the device can cause
loss of sight.
Wear protective gloves.
Caution! Wear a breathing mask.
Dust which is injurious to health
can be generated when working
on wood and other materials.
Never use the device to work on
any materials containing asbestos!
It is forbidden to remove or
tamper with the protection
devices and safety devices.
Caution! Risk of injury! Failure
to keep your hands away from
the blade will result in serious
personal injury.
Disconnect the mains plug prior
to the repair, cleaning, and
maintenance of the splitter!
Keep children and bystanders off
and away.
SAFETY
General Safety Rules
Understand your Machine
Read this manual and labels affixed to the
machine to understand its limitations and
potential hazards.
Be thoroughly familiar with the controls and
their proper operation. Know how to stop the
machine and disengage the controls quickly.
Do not attempt to operate the machine until
you fully understand how to properly operate
and maintain the engine and how to avoid
accidental injuries and/or property damage.
If the unit is to be used by someone other than
original purchaser or loaned, rented, or sold,
always provide this manual and any needed
safety training before operation. The user can
prevent and is responsible for accidents or
injuries that may occur to themselves, other
people, and property.
Do not force the machine. Use the correct
machine for your application. The correct
machine will do the job more efficiently and
safer at the rate it was designed.
Personal Safety
Do not permit children to operate this machine
at any time.
Keep children, pets, and other people not
using the unit away from the work area. Be
alert and shut off unit if anyone enters work
area. Keep children under the watchful care of
a responsible adult.
Do not operate the machine while under the
influence of drugs, alcohol, or any medication
that could affect your ability to use it properly.
Dress properly. Wear heavy long pants, boots,
and gloves. Do not wear loose clothing, short
pants, or jewelry of any kind. Secure long hair
so it is above shoulder level. Keep your hair,
clothing, and gloves away from moving parts.
Loose clothes, jewelry, or long hair can be
caught in moving parts.
Protect eyes, face, and head from objects that
may be thrown from the unit. Always wear
safety goggles or safety glasses with side
shields when operating.
65050UK00M100.indd 3 2020/5/27 9:36:10

TABLE SAW
4
GB Wear appropriate hearing protection. Wear
respiratory protection to avoid the risk of
inhaling harmful dust.
Always keep hands and feet away from all
moving parts during operation. Moving parts
can cut or crush body parts.
Always keep hands and feet away from all
pinch points.
Do not touch parts that might be hot
from operation. Allow parts to cool before
attempting to maintain, adjust, or service.
Stay alert, watch what you are doing, and use
common sense when operating the machine.
Do not overreach. Do not operate the machine
while barefoot or when wearing sandals or
similar lightweight footwear. Wear protective
footwear that will protect your feet and
improve your footing on slippery surfaces.
Keep proper footing and balance at all times.
This enables better control of the machine in
unexpected situations.
Inspect your Machine
Check your machine before starting it. Keep
guards in place and in working order. Make
sure all nuts, bolts, etc., are securely tightened.
Never operate the machine when it is in need
of repair or is in poor mechanical condition.
Replace damaged, missing, or failed parts
before using it. Keep the machine in safe
working condition. Regularly check to see that
keys and adjusting wrenches are removed
from the machine area before starting it. A
wrench or a key that is left attached to a
rotating part of the machine may result in
personal injury. Avoid accidental starting.
Be sure the motor switch is off before
transporting the machine or performing any
maintenance or service on the unit.
Transporting or performing maintenance
or service on a machine with its switch on
invites accidents. If the machine should start
to vibrate abnormally, stop the motor and
check immediately for the cause. Vibration is
generally a warning sign of trouble.
Electric Safety
Protect yourself from electric shock. Do not
plug or unplug the motor while standing in or
around damp or wet ground. Do not use the
unit in wet or damp areas or expose it to rain.
Prevent body contact with grounded surfaces:
pipes, radiators, ranges, and refrigerator
enclosures. Make sure your fingers do not
touch the plug’s metal prongs when plugging
or unplugging the unit.
Avoid inadvertent starting. Make sure that the
switch is switched off when plugging the plug
into an outlet.
Only use approved and appropriately
identified extension cables for use outdoors.
Only use cable reels in the unrolled state.
Do not use the cable for purposes for which
it is not intended. Do not use the cable to pull
the plug out of the outlet. Protect the cable
from heat, oil and sharp edges.
Have your electric tool repaired by a qualified
electrician. This electric tool conforms to the
applicable safety regulations. Repairs may
only be performed by an electrician using
original spare parts. Otherwise accidents can
occur.
Work Area & Store Area
Keep the work area orderly. Disorder in the
work area can lead to accidents.
Take environmental influences into account.
Do not expose electric tools to rain. Do
not use electric tools in a damp or wet
environment. Make sure that the work area
is well-illuminated. Do not use electric tools
where there is a risk of fire or explosion.
Securely store unused electric tools. Unused
electric tools should be stored in a dry,
elevated or closed location out of the reach of
children.
Specific Safety Rules
Safety Precautions
Do not use damaged, cracked or deformed
saw blades.
Replace a worn table insert.
Only use saw blades recommended by the
manufacturer which conform to EN 847-1.
Keep attention when changing the saw blade.
The cutting width is not smaller and the main
blade thickness of the saw blade is not greater
than the thickness of the gap wedge.
65050UK00M100.indd 4 2020/5/27 9:36:11

TABLE SAW 5
GB
Make sure that a suitable saw blade for the
material to be cut is selected.
Wear gloves when handling saw blades and
rough materials.
Carry saw blades in a container whenever
practical.
Wear goggles. Sparks generated during work
or splinters, chippings and dust coming from
the device can lead to loss of eyesight.
Connect a dust collecting device to the
electric tool when sawing wood. The emission
of dust is influenced, among other things,
by the type of material to be processed, the
significance of local separation (collection or
source) and the correct setting of the hood/
guide plates/guides.
Do not use saw blades made of high-speed
alloy steel (HSS steel).
In times of non-use keep the push stick or the
push block with the electrical power tool in its
holder at all times.
Machine Use and Care
Do not use low-output electric tools for heavy
work. Do not use the electric tool for purposes
for which it is not intended. For example, do
not use hand-held circular saws for the cutting
of branches or logs. Do not use the electric
tool to cut firewood.
Secure the workpiece. Use the clamping
devices or a vice to hold the workpiece in
place. In this manner, it is held more securely
than with your hand. An additional support is
necessary for long workpieces (table, trestle,
etc.) in order to prevent the machine from
tipping over. Always press the workpiece
firmly against the working plate and stop in
order to prevent bouncing and twisting of the
workpiece.
When the saw blade is blocked due to
abnormal feed force during cutting, turn the
machine off and disconnect it from power
supply. Remove the work piece and ensure
that the saw blade runs free. Turn the machine
on and start new cutting operation with
reduced feed force.
Use the push stick or handle with sliding
wood, to pass the workpiece securely out off
the saw blade.
Make sure that the riving knife is always used,
and set up is correctly.
Use the upper blade guard and set it to the
correct position.
Only use saw blades for which the maximum
permissible speed is not lower than the maxi-
mum spindle speed of table saws and which
are suitable for the material to be cut.
Do not cut rebates or grooves without fitting
a suitable guard, e.g. a tunnel-type guard, over
the saw table.
Circular saws must not be used for slotting
jobs (cutting grooves which end in the
workpiece).
When transporting the electric tool, only
use the transport devices. Never use the
protective devices for handling or transport.
Make sure that the upper part of the saw
blade is covered during transport, e.g. by the
protective device.
Be sure to only use spacers and spindle rings
specified by the manufacturer as suitable for
the intended purpose.
The floor around the machine must be level,
clean and free of loose particles, such as chips
and cutting residues.
Always stand to the side of the saw blade
when working with the saw.
Do not remove any cutting residues or other
parts of workpieces from the cutting zone
while the machine is running and the saw unit
is not at rest.
Make sure that the machine is always secured
on a workbench or a table if at all possible.
Support long workpieces (e.g. with a roller
table) to prevent them sagging at the end of a
cut.
Never remove loose splinters, chips or jammed
pieces of wood while the saw blade is running.
Switch off the machine to troubleshoot or
remove jammed pieces of wood.
Refitting, including adjusting and measuring
works, and cleaning must be carried out only
when the motor is switched off. - Disconnect
the main power plug -
Before switching on again, ensure that keys
and adjustment tools have been removed.
65050UK00M100.indd 5 2020/5/27 9:36:11

TABLE SAW
6
GB This electric tool generates an electromagnetic
field during operation. This field can impair
active or passive medical implants under
certain conditions. In order to prevent the risk
of serious or deadly injuries, we recommend
that persons with medical implants consult
with their physician and the manufacturer of
the medical implant prior to operating the
electric tool.
Take care of your tools. Keep cutting tools
sharp and clean in order to be able to work
better and more safely. Follow the instructions
for lubrication and for tool replacement.
Check the connection cable of the electric tool
regularly and have it replaced by a recognized
specialist when damaged. Check extension
cables regularly and replace them when
damaged. Keep the handle dry, clean and free
of oil and grease.
Safety Instructions for the Handling of Saw Blades
Only use insertion tools if you have mastered
their use.
Observe the maximum speed. The maximum
speed specified on the insertion tool may not
be exceeded. If specified, observe the speed
range.
Observe the motor / saw blade direction of
rotation.
Do not use any insertion tools with cracks.
Sort out cracked insertion tools. Repairs are
not permitted.
Clean grease, oil and water off of the clamping
surfaces.
Do not use any loose reducing rings or bushes
for the reducing of holes on saw blades.
Make sure that fixed reducer rings for securing
the insertion tool have the same diameter and
have at least 1/3 of the cutting diameter.
Make sure that fixed reducer rings are parallel
to each other.
Handle insertion tool with caution. They are
ideally stored in the originally package or
special containers. Wear protective gloves in
order to improve grip and to further reduce
the risk of injury.
Prior to the use of insertion tools, make
sure that all protective devices are properly
fastened.
Prior to use, make sure that the insertion
tool meets the technical requirements of this
electric tool and is properly fastened.
Only use the supplied saw blade for sawing
operations in wood, materials similar to wood,
plastics and non-ferrous metals (except for
magnesium and alloys containing magnesium).
Connect the dust extraction device if you
will be processing wood, materials similar
to wood, or plastics. If connections for dust
extraction and a collecting device are present,
make sure that they are connected and used
properly. When processing wood, materials
similar to wood, and plastics. Operation in
enclosed spaces is only permitted with the use
of a suitable extraction system.
Maintenance and Repair
Pull out the mains plug for any adjustment or
repair tasks.
The generation of noise is influenced by
various factors, including the characteristics
of saw blades, condition of saw blade and
electric tool. Use saw blades which were
designed for reduced noise development,
insofar as possible. Maintain the electric
tool and tool attachments regularly and if
necessary, initiate repairs in order to reduce
noise.
Report faults on the electric tool, protective
devices or the tool attachment to the person
responsible for safety as soon as they are
discovered.
Check the electric tool for potential damage.
Protective devices and other parts must be
care-fully inspected to ensure that they are
fault-free and function as intended prior to
continued use of the electric tool. Check
whether the moving parts function faultlessly
and do not jam or whether parts are dam-
aged. All parts must be correctly mounted and
all conditions must be fulfilled to ensure fault-
free operation of the electric tool. The moving
protective hood may not be fixed in the open
position. Damaged protective devices and
parts must be properly repaired or replaced
by a recognized workshop, insofar as nothing
different is specified in the operating manual.
Damaged switches must be replaced at a
customer service workshop. Do not use any
faulty or damaged connection cables. Do
not use any electric tool on which the switch
cannot be switched on and off.
65050UK00M100.indd 6 2020/5/27 9:36:11

TABLE SAW 7
GB
Residual Risks
Despite proper use, additional residual risks
cannot be completely ruled out. The following
risks may arise due to the nature of the table
saw:
• Touching the exposed areas of the saw
blade;
• Reaching into the rotating saw blade (cut
injury);
• Kickback of the workpieces and parts of the
workpiece if used improperly;
• Saw blade breaks;
• Projection of defective hard metal parts of
the saw blade;
• Hearing loss in the event of failure to use the
required ear protection;
• Damage to the eyes if the required safety
goggles are not used;
• Injury to health if the required dust mask is
not used;
• Emission of wood dust that is harmful to
health if used in enclosed spaces.
65050UK00M100.indd 7 2020/5/27 9:36:11

TABLE SAW
8
GB
The table saw comes partially assembled and is shipped in carefully packed carton. After all the
parts have been removed from the carton, you should have:
CONTENTS SUPPLIED
(× 4)
(× 2)
(× 2)
(× 2)
(× 4) (× 2)
(× 4)
(× 2)
22
23
25
15
16
18
17
2
5
7
10
11
9
8
12
6
14
4
1
3
24
19
13
21
20
1. Bench Insert
2. Main Machine
3. Push Stick
4. Bench Length Extension
5. Bench Width Extension - Left
6. Bench Width Extension - Right
7. Rip Fence
8. Long Support Strut (×2)
9. Short Support Strut (×4)
10. Long Centre Brace (×2)
11. Short Centre Brace (×2)
12. Leg (×4)
13. Saw Blade Guard & Hose
14. Miter Gauge
15. Ring Spanner
16. Saw Blade Key
17. Hex Key
18. Leg Support (×2)
19. Riving Knife
20. Battery (×2)
21. Operator’s Manual
22. Crank
23. Rubber Foot (×4)
24. Elbow Connection
25. Hardware Bag, Including
M6 ×12 ×10 A
M5 ×14 ×2
M6 ×16 ×8
B
M6 ×12 ×20 C
65050UK00M100.indd 8 2020/5/27 9:36:11

TABLE SAW 9
GB
This table saw was partially assembled at the
factory. To assemble your machine follow the
below instructions.
Bench Extensions
1. Turn the saw and place it on the floor with
the bench facing down.
2. Align the bench extensions flush with the
saw bench.
3. Push the bench width extension onto the
sawing bench using the bolts M6×12 and
loosely fasten the flat washers and nuts M6.
Repeat for the opposite side.
4. Push the bench length extension onto the
saw bench using the screws M5x14 and
loosely fasten the spring washers and flat
washers.
5. Screw the support struts to the bench
extensions with bolts M6×12, flat washers
and nuts M6.
6. Tighten all the bolts, screws and nuts
M6 ×12 ×10 A
M5 ×14 ×2
M6 ×12 (×10)
Support Strut
Outside Hole
M5 ×14 (×2)
ASSEMBLY
Support Legs
1. Screw the four support legs together with
the support struts onto the main frame with
the bolts M6×16, spring washers and flat
washers.
2. Place the rubber feet onto the support legs.
M6 ×16 ×8 B
Long /Short Centre Brace & Leg Support
1. Screw the long centre braces and the short
centre braces onto the legs using the bolts
M6×12, flat washers and nuts M6.
Make sure that the same braces face each
other. The long centre braces must be
mounted parallel to the operator's side of
the saw.
2. Align the holes of two leg supports with
the holes of the rear support legs. Screw
M6×12, flat washers and nuts M6. Both leg
supports must be fastened to the back of
the machine.
3. Tight all the nuts and bolts.
M6 ×16 (×8)
65050UK00M100.indd 9 2020/5/27 9:36:12

TABLE SAW
10
GB
Height Adjusting Handlebar
1. Turn the saw and make sure it stand on the
flat ground.
2. Unscrew the washers and nut from the
crank. See below illustration 1.
3. Mount the crank with the washers you have
already affixed and the lock nuts to the
crank wheel in such a way that the crank will
still turn. See below illustration 2.
M6 ×12 ×20 C
M6 ×12 (×20)
Leg Support
1
2
3. Loosen the clamping bolt on the clamping
plate with the ring spanner by a few turns in
an anti-clockwise direction. See illustration 3.
4. Insert the riving knife behind the clamping
plate and push it all the way down.
5. Gently screw the clamp bolt tight in a
clockwise direction.
6. Align the riving knife so that there is 3-5mm
of space to the saw blade on all sides. See
illustration 5.
7. Fix the riving knife in place by tightening the
clamp bolt by turning it clockwise again.
Riving Knife
1. Rotate the height adjusting handlebar to
set the blade to the max. cutting depth. See
below illustration 1.
2. Unscrew the bevel limitation stopper, turn
the bevel adjusting handwheel to set the
blade to the 0 position and fasten the bevel
limitation stopper. See below illustration 2.
1 2
Bevel Limitation Stopper
65050UK00M100.indd 10 2020/5/27 9:36:12

TABLE SAW 11
GB
Clamp Bolt
Riving Knife
45
Max. 3-5mm
3
8. Fasten the bench insert into the saw table
with both fixing screws. See illustration 6.
9. Insert the batteries.
Saw Blade Guard & Suction Hose
1. Unscrew the wing screw in the blade guard.
2. Carefully guide the guard over the laser and
onto the riving knife. The wing screw inserts
into the L groove in the riving knife, then
pull the blade guard back to make sure wing
screw perferctly clamp the groove.
3. Fasten the blade guard to the riving knife
using wing screw. Do not overtighten the
wing screw. It should be easy to lift the
blade guard up and down.
Caution! the saw blade guard must be
lowered onto the workpiece before
starting the sawing operation.
12
6
4. Plug the suction hose onto the suction
adapter in the back of machine.
5. Attach the elbow connection.
Miter Gauge
1. Insert the miter gauge into the table slot
from the table's front edge.
2. Set the desired angle after loosening the
miter gauge's knurled knob and retighten
knurled knob.
Suction Adapter
Elbow Connection
65050UK00M100.indd 11 2020/5/27 9:36:13

TABLE SAW
12
GB
Rip Fence
1. Position the rip fence with the opened
locking lever on the guide rail on the saw
bench.
2. Fence must be parallel with saw blade and
lock in position by pressing the locking lever
down.
3. In order to change the position of the rip
fence. Push the rip fence with the opened
locking lever along the guide rail.
4. In order to fasten the rip fence in the required
position, push the locking lever all the way
down to lock it. See illustration 2.
1
Rip Fence
2
Locking Lever
Guide Rail
Knurled Knob
65050UK00M100.indd 12 2020/5/27 9:36:14

TABLE SAW 13
GB
KNOW YOUR MACHINE
Features and Controls
ON/OFF Switch
The saw can be switched on by pressing the
green pushbutton.
The red pushbutton has to be pressed to
switch off the saw.
Blade Guard
Always keep the removable blade guard down
over the saw blade for through-sawing cuts.
Bench Extension
This bench extensions give the operator
additional support when cutting wide
workpiece.
Riving Knife
A removable metal piece of the blade guard
assembly, slightly thinner than the saw blade,
which helps keep the kerf open and prevent
kickback.
Bevel Locking Lever
This lever, placed just under the saw table
surface on the front of cabinet, locks the angle
setting of the blade.
Height/Bevel Adjusting Handwheel
Located on the front of the cabinet, use this
handwheel to lower and raise the blade for
height adjustments or blade replacement. This
handwheel also make the adjustment for bevel
angles easy.
Miter Gauge
The miter gauge aligns the wood for a cross
cut. The easy-to-read indicator shows the
exact angle for a miter cut.
Rip Fence
A sturdy metal fence guides the workpiece
and is secured with locking lever.
Saw Bench
ON/OFF Switch
Miter Guage
Leg
Bench Extension
Saw Blade Guard
Bevel Limitation Stopper
Bevel Adjusting Wheel
Blade
Riving Knife
Rip Fence
Height Adjusting Handlebar
Leg Support
Push Stick
Locking Lever
Bevel Indicator
65050UK00M100.indd 13 2020/5/27 9:36:16

TABLE SAW
14
GB
Change Blade Depth
Turn the height adjusting handlebar to set the
blade to the required cutting depth.
Counterclockwise: smaller cutting depth
Clockwise: larger cutting depth
After each new adjustment it is advisable to
carry out a trial cut in order to check the set
dimensions.
Change Blade Angle
If the bevel indicator is not at zero when the
saw blade is at 90°, adjust the indicator by
loosening the screw and setting at 0° on the
bevel scale. Retighten the screw.
Unplug the saw.
Loosen the bevel limitation stopper.
Set the desired angle on the scale by pressing
and turning the bevel adjusting handwheel.
Tighten the bevel limitation stopper in the
required angle position.
Working with the Rip Fence
Set the Guide Height
The stop rail of the rip hence has two guide
surfaces with different heights.
For thick material you must use the stop rail as
shown in below inllustration 2, for thin material
you must use the stop rail as shown in below
inllustration 3.
Set Up
Screw
Bevel Indicator
Set the Cutting Width
• The rip hence has to be used when making
longitudinal cuts in wooden workpieces.
• The rip hence can be mounted on either side
of the saw table.
• The rip hence can be set to the required
dimension with the help of the scale on the
guide rail.
On the guide rail, there are 2 scales which
indicate the distance between the rip fence
and the saw blade.
Select the appropriate scale depending on
whether the stop rail is rotated for processing
thick or thin material:
To change over the stop rail to the lower
guide face you have to slacken the two
knurled bolts in order to disconnect the stop
rail from the guide tube.
Remove the two knurled bolts through the
one slot in the stop rail and insert in the other
slot. Remount the stop rail on the guide rail
using knurled bolts.
The procedure for changing over to the high
guide face is similar.
The stop rail can be applied to the left or right
of the guide tube as needed.
90°
1
Knurled Bolt
Stop Rail
2 3
65050UK00M100.indd 14 2020/5/27 9:36:17

TABLE SAW 15
GB
Adjusting the laser
If the laser no longer displays the correct
cutting line, it can be subsequently adjusted.
Loosen the screws on the
illuminating diode and
position the laser in the
required direction by pushing
it in such a way that the laser
beam meets the cutting teeth
of the saw blade.
Then tighten the screws again.
Knurled Knob
High stop rail: thick material
Low stop rail: thin material
Set the rip fence to the desired level in the
sight glass and fix it with the locking lever.
Use the Miter Gauge
The Miter gauge provide greater accuracy in
angled cuts. For very close tolerances, test
cuts are recommended.
There are two miter gauge channels, one on
either side of the blade. When making 90
cross cut, you can use either miter gauge
channel. When making a beveled cross cut(
the blade tilted in relation to the table) the
miter gauge should be located in the slot on
the right so that the blade I tilted away from
the miter gauge and your hands.
The miter gauge can be turned 60 to the right
or left.
Loosen the knurled knob.
With the miter gauge in the miter gauge slot,
rotate the gauge until the desired angle is
reached on the scale.
Retighten the knurled knob.
-
-
Making Longitudinal Cuts
Longitudinal cutting is when you use the saw
to cut along the grain of wood.
Press one edge of the workpiece against the
rip fence while the flat side lies on the saw
table. The blade guard must always lower over
the workpiece. When you make a longitudinal
cut, never adopt a working position that is in
line with the cutting direction.
Operation
1. Set the rip fence in accordance with the
workpiece and the desired width.
2. Switch on the saw.
3. Place your hands( with fingers closed) flat
on the workpiece and push the workpiece
along the rip fence and into the blade.
4. Guide at the side with your left or right hand
(depending on the position of the rip fence)
only as far as the front edge of the saw
blade guard.
5. Always push the workpiece through to the
end of the riving knife.
6. The offcut piece remains on the saw blade
until the blade I back in its position of rest.
7. Secure long workpiece against falling off at
the end of the cut.
Cutting Narrow Workpieces
Be sure to use a push stick when making
longitudinal cuts in workpieces smaller than
120 mm in width. A push stick is supplied with
the saw. Replace a damaged or worn push
stick immediately.
1. Adjust the rip fence to the width of workpiece
you require.
2. Feed in the workpiece with two hands.
Always use the push stick in the area of the
saw blade.
3. Always push the workpiece through to the
end of the riving knife.
Warning! With short workpiece, use
the push stick from the beginning.
Screw (×2)
65050UK00M100.indd 15 2020/5/27 9:36:18

TABLE SAW
16
GB The laser beam is produced using a laser
diode. A line is produced which you can use
as an optical mark for the cutting line when
precision cutting. The laser switch can be
accessed through the opening on the top side
if the saw blade guard is mounted.
Activating/deactivating the laser
With the help of the laser you can perform
precision cuts with the table saw. Observe the
safety instructions for the laser.
To switch the laser on, set the laser switch
to position I (laser on).
A red laser beam will now be emitted out
of the laser light opening. Keeping the laser
beam along the cutting line mark while
sawing will ensure that your cuts are neat.
To switch the laser off, set the laser switch
to position 0 (laser off). The laser beam will
go out.
To save the battery power, always switch
the laser off when it is no longer needed.
Immediately switch the table saw off and
pull the mains plug out of the socket if the
saw blade catches in the workpiece or any
other blockages occur.
Use protective gloves. Do not touch the saw
blade with your bare hands.
-
-
-
-
-
Dust and chips that have accumulated
may block the laser beam. These
particles must therefore be removed
from the saw blade guard after every
use.
Warning! Always hold the guided
part of the workpiece. Never hold
the part which is to be cut off.
Risk of injury! Incorrect handling of
the table saw poses a risk of serious
injury.
5. Push the miter gauge forward until the
workpiece is cut all the way through.
6. Switch off the saw. Do not remove the offcut
until the blade has stopped rotating.
Making Angular Cuts
Angular cuts must always be made using the
rip fence.
1. Set the blade to the desired angle.
2. Set the rip fence in accordance with the
workpiece width and height.
3. Carry out the cut in accordance with the
workpiece width.
Making Cross Cuts
1. Slide the miter gauge into one of the grooves
in the table and adjust to the required angle.
If you want to tilt the blade, use the left
groove which prevents your hand and the
miter gauge from making contact with the
blade guard.
2. Press the workpiece firmly against the miter
gauge.
3. Switch on the saw.
4. Push the miter gauge and the workpiece
toward the blade in order to make the cut.
Releasing the overload protection
This table saw is equipped with overload
protection. If the motor has overloaded, the
overload switch automatically deactivates it to
protect the table saw from overheating.
1. If the overload protection has been activated,
switch the table saw off by pressing the red
operating switch 0.
2. Wait until the motor has cooled down.
3. Press the overload switch and switch the
table saw on again by pressing the green
operating switch I.
Removing jammed material
65050UK00M100.indd 16 2020/5/27 9:36:18

TABLE SAW 17
GB
Danger! The carbon brushes should
not be replaced by anyone but a
qualified electrician.
Saw Blade Change
1. Ensure that the table saw is not connected
to the mains supply.
2. Use protective gloves. Do not touch the saw
blade with your bare hands.
3. Make sure that the saw blade has been
lowered all the way into the saw table. If
necessary, lower the saw blade by turning
the crank counterclockwise up to the stop
point.
4. Remove the saw blade guard from the
riving knife by loosening the wing screw.
Gently pulling the saw blade guard apart.
See below illustration 1.
5. Loosen the two fixing screws and remove
the bench insert. See below illustration 2.
Warning! Prior to any adjustment,
maintenance or service work
disconnect the mains power plug!
Carbon Brushes Inspection
In case of excessive sparking, have the
carbon brushes checked only by a qualified
electrician.
General Maintenance Measures
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
We recommend that you clean the device
immediately each time you have finished using
it.
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use cleaning
agents or solvents; these could attack the
plastic parts of the equipment. Ensure that no
water can seep into the device. The ingress of
water into an electric tool increases the risk of
an electric shock.
In order to extend the service life of the tool,
oil the rotary parts once monthly. Do not oil
the motor.
MAINTENANCE
1. Turn off the power tool before any transport
and disconnect it from the power supply.
2. Apply the power tool at least with two
people, do not touch the table extensions.
3. Protect the power tool from knocks, bumps
and strong vibrations such as during
transport in vehicles.
4. Secure the power tool against overturning
and sliding
5. Never use the safety devices for handling or
transporting purpose.
TRANSPORT
6. Make sure that the angle of the saw blade
is set to 0°.
7. Rotate the saw blade all the way out of the
saw table by turning the crank clockwise up
to the stop point. See below illustration 3.
Always check the bench insert in the
process: Immediately replace the
bench insert if it is damaged or is no
longer flush with the saw table.
1
3
2
Riving Knife
65050UK00M100.indd 17 2020/5/27 9:36:18

TABLE SAW
18
GB 8. Remove the riving knife by loosening the
clamp bolt in the clamping plate by turning
it clockwise a few revolutions and then
pulling the riving knife up and out. See
below illustration 4.
9. Attach the ring spanner to the fixing nut.
See below illustration 5.
10. Fasten the drive shaft with the saw blade
key. See below illustration 5.
11. Turn the fixing nut in an anti-clockwise
direction using the ring spanner.
12. Carefully hold the saw blade with one hand
and remove the fixing nut and the outer saw
blade flange from the drive shaft. See below
illustration 6.
13. Now take the saw blade off of the drive
shaft and carefully pull it up and out of the
saw table. See below illustration 6.
16. Place the outer saw blade flange back on
the drive shaft. At the same time, make sure
that the outer saw blade flange is correctly
aligned.
17. Tighten the fixing nut to the drive shaft by
hand.
18. Carefully turn the saw blade in the direction
of rotation: It must be exactly centred
and must not “wobble”. Check the correct
positioning of the saw blade and outer saw
blade flange and adjust the parts again if
the saw blade is not precisely centred.
19. Attached the ring spanner to the fixing nut
and hold the drive shaft with saw blade key.
Turn the fixing nut with ring spanner in a
clockwise direction.
20.Mount the riving knife, the bench insert and
the saw blade guard.
14. Clean the outer and inner saw blade flange
thoroughly before mounting a new saw
blade.
15. Mount a new saw blade on the drive shaft.
Pay attention to the rotational
direction: The cutting interface of
the teeth must be in the direction
of rotation (forwards). Usually, the
direction of rotation is indicated on
the saw blade.
Store the equipment and accessories in a dark
and dry place at above freezing temperature.
The ideal storage temperature is between 5
and 30°C. Store the electric tool in its original
packaging. Cover the electric tool in order to
protect it from dust and moisture.
STORAGE
6
Fixing Nut
Drive Shaft
Blade Flange
5
Ring Spanner Saw Blade Key
4
65050UK00M100.indd 18 2020/5/27 9:36:19

TABLE SAW 19
GB
TROUBLE SHOOTING
Problem Cause Remedy
Motor does not
start
1. Fastening nut tightened
insufficiently
2. Extension cable defect
3. Connections on the motor or
switch defect
1. Check the mains fuse
2. Check the extension cable
3. Have it checked by an electrician
No Motor
output turns off
automatically
1. Overload by dull saw blade
2. Thermoprotection is triggered
1. Insert a sharpened saw blade
2. Motor can be turned on again after
the cooling period.
Excess vibration
1. Blade is out of balance
2. Blade is damaged
3. Saw is not mounted securely
4. Work surface is uneven
5. Blade is warped
1. Replace the blade
2. Replace the blade
3. Tighten all the hardware
4. Reposition on flat surface
5. Replace the blade
Cutting binds or
burns work
1. Blade is dull
2. Work is fed too fast
3. RIp fence is misaligned
4. Wood is warped
1. Replace t or Sharpen blade
2. Slow the feed rate
3. Align the rip fence
4. Replace the wood. Always cut with
convex side to table surface.
Wood edges away
from rip fence when
ripping
Rip fence is misaglined Check and adjust the rip fence
Height/bevel
adjusting handwheel
is hard to turn
Gears or screw post inside
cabinet are clogged with saw
dust
Clean the gears or screw post
Saw does not make
accurate 90° or 45°
cuts
Miter gauge is misaligned (Miter
Cuts) Adjust the miter gauge
65050UK00M100.indd 19 2020/5/27 9:36:19

TABLE SAW
20
GB PARTS SCHEDULE
65050UK00M100.indd 20 2020/5/27 9:36:20