TLV EF200F-C User manual

172-65757M-01(EF200F-CVortexflowmeter)7June2022
EF200F-C
Vortexflowmeter
Copyright©2022byTLVCO.,LTD.
Allrightsreserved

EF200F-C
2
• Makesurethedocumentisstoredinasafeplacesuchthatitisalwaysavailablewhen
workingonorwiththedevice.
• Toavoiddangertoindividualsorthefacility,readthe"Basicsafetyinstructions"section
carefully,aswellasallothersafetyinstructionsinthedocumentthatarespecificto
workingprocedures.
• Themanufacturerreservestherighttomodifytechnicaldatawithoutpriornotice.Your
TLVSalesCenterwillsupplyyouwithcurrentinformationandupdatesto
theseinstructions.

EF200F-C Tableofcontents
3
Table of contents
1 Aboutthisdocument
1.1 Documentfunction
1.2 Symbols
1.2.1 Safetysymbols
1.2.2 Electricalsymbols
1.2.3 Toolsymbols
1.2.4 Symbolsfor
1.2.5 Symbolsingraphics
certaintypesofinformation
1.3 Documentation
1.3.1 Standarddocumentation
1.3.2 Supplementarydevice-dependent
documentation
2 Safetyinstructions
2.1 Requirementsforthepersonnel
2.2 Designateduse
2.3 Workplacesafety
2.4 Operationalsafety
2.5 Productsafety
2.6 ITsecurity
2.7 Device-specificITsecurity
2.7.1 Protectingaccessviahardwarewrite
protection
2.7.2 Protectingaccessviaapassword
2.7.3 Accessviafieldbus
3 Productdescription
3.1 Productdesign
4 Incomingacceptanceandproduct
identification
4.1 Incomingacceptance
4.2 Productidentification
4.2.1 Transmitternameplate
4.2.2 Sensornameplate(remoteversion)
4.2.3 NameplateforTEG
5 Storageandtransport
5.1 Storageconditions
5.2 Transportingtheproduct
5.2.1 Measuringdeviceswithoutlifting
lugs
(compactversion/remoteversion)
5.2.2 Measuringdeviceswithliftinglugs
6 Installation
6.1 Installationconditions
6.1.1 Mountingposition
6.1.2 Environmentandprocess
requirements
6.1.3 Ensuringaccuratemeasurements
6.2 Mountingthemeasuringdevice
6.2.1 Requiredtools
6.2.2 Preparingthemeasuringdevice
6.2.3 Mountingthesensor
6.2.4 Mountingthepressuremeasuring
unit
6.2.5 Mountingthetransmitterofthe
remoteversion
6.2.6 Turningthetransmitterhousing
6.2.7 Turningthedisplaymodule
6.3 Post-installationcheck
7 Electricalconnection
7.1 Connectionconditions
7.1.1 Requiredtools
7.1.2 Connectingcablerequirements
7.1.3 Connectingcableforremote
version
7.1.4 Terminalassignment
7.1.5 Requirementsforthesupplyunit
7.1.6 Preparingthemeasuringdevice
7.2 Connectingthemeasuringdevice
7.2.1 Connectingthecompactversion
7.2.2 Connectingtheremoteversion
7.2.3 Connectingtheconnectingcablefor
thepressuremeasuringcell
7.2.4 Ensuringpotentialequalization
7.3 Ensuringthedegreeofprotection
7.4 Post-connectioncheck
8 Operationoptions
8.1 Overviewofoperationoptions
8.2 Structureandfunctionoftheoperating
menu
8.2.1 Structureoftheoperatingmenu
8.2.2 Operatingphilosophy
8.3 Accesstotheoperatingmenuviathelocal
display
8.3.1 Operationaldisplay
8.3.2 Navigationview
8.3.3 Editingview
8.3.4 Operatingelements
8.3.5 Openingthecontextmenu
8.3.6 Navigatingandselectingfromlist
8.3.7 Callingtheparameterdirectly
8.3.8 Callinguphelptext
8.3.9 Changingtheparameters
2.8 Vibrations
2.9 PreventingExcessiveFlow
2.10 PulsatingInfluences
2.11 PreventMixedPhaseFlowy
2.12 EnsurePipeisFlooded
2.13 BypassLines
7.5 ConnectingtoTLVEC351FlowComputer

Tableofcontents EF200F-C
4
8.3.10 Userrolesandrelatedaccess
authorization
8.3.11 Disablingwriteprotectionviaaccess
code
8.3.12 Enablinganddisablingthekeypad
lock
8.4 Accesstotheoperatingmenuviathe
operatingtool
8.4.1 Connectingtheoperatingtool
9 Systemintegration
9.1 Overviewofdevicedescriptionfiles
10 Commissioning
10.1 Functioncheck
10.2 Switchingonthemeasuringdevice
10.3 Settingtheoperatinglanguage
10.4 Configuringthemeasuringdevice
10.4.1 Definingthetagname
10.4.2 Settingthesystemunits
10.4.3 Selectingandsettingthemedium
10.4.4 Configuringthecurrentinput
10.4.5 Configuringthecurrentoutput
10.4.6 Configuringthepulse/frequency/
switchoutput
10.4.7 Configuringthelocaldisplay
10.4.8 Configuringthelowflowcutoff
10.5 Advancedsettings
10.5.1 Settingthemediumproperties
10.5.2 Performingexternalcompensation
10.5.3 Carryingoutasensoradjustment
10.5.4 Configuringthetotalizer
10.5.5 Carryingoutadditionaldisplay
configurations
10.5.6 Configurationmanagement
10.5.7 Usingparametersfordevice
administration
10.6 Configurationmanagement
10.6.1 Functionscopeofthe"Configuration
management"parameter
10.7 Simulation
10.8 Protectingsettingsfromunauthorized
access
10.8.1 Writeprotectionviaaccesscode
10.8.2 Writeprotectionviawriteprotection
switch
10.9 Application-specificcommissioning
10.9.1 Steamapplication
10.9.2 Liquidapplication
10.9.3 Gasapplications
10.9.4 Calculationofthemeasured
variables
11 Operation
11.1 Readingthedevicelockingstatus
11.2 Adjustingtheoperatinglanguage
11.3 Configuringthedisplay
11.4 Readingmeasuredvalues
11.4.1 Processvariables
11.4.2 "Totalizer"submenu
11.4.3 Inputvalues
11.4.4 Outputvalues
11.5 Adaptingthemeasuringdevicetotheprocess
conditions
11.6 Performingatotalizerreset
11.6.1 Functionscopeofthe"Control
Totalizer"parameter
11.6.2 Functionscopeofthe"Resetall
totalizers"parameter
12 Diagnosticsandtroubleshooting
12.1 Generaltroubleshooting
12.2 Diagnosticinformationonlocaldisplay
12.2.1 Diagnosticmessage
12.3 Adaptingthediagnosticinformation
12.3.1 Adaptingthediagnosticbehavior
12.3.2 Adaptingthestatussignal
12.4 Overviewofdiagnosticinformation
12.4.1 Operatingconditionsfordisplaying
thefollowingdiagnostics
information
12.4.2 Emergencymodeintheeventof
pressurecompensation
12.4.3 Emergencymodeineventof
temperaturecompensation
12.5 Pendingdiagnosticevents
12.6 Diagnosticlist
12.7 Eventlogbook
12.7.1 Readingouttheeventlogbook
12.7.2 Filteringtheeventlogbook
12.7.3 Overviewofinformationevents
12.8 Resettingthemeasuringdevice
12.8.1 Functionscopeofthe"Devicereset"
parameter
12.9 Deviceinformation
13 Maintenance
13.1 Maintenancetasks
13.1.1 Exteriorcleaning
13.1.2 Interiorcleaning
13.1.3 Replacingseals
13.1.4 Adjustingthepressuremeasuring
cell
9.1.1
Currentversiondateforthedevice
12.2.2 Callingupremedialmeasures

EF200F-C Tableofcontents
5
14 Repair
14.1 Generalnotes
14.1.1 Repairandconversionconcept
14.1.2 Notesforrepairandconversion
14.2 Spareparts
14.3 Disposal
14.3.1 Removingthemeasuringdevice
14.3.2 Disposingofthemeasuringdevice
15 Accessories
15.1 Device-specificaccessories
15.1.1 Forthetransmitter
15.1.2 Forthesensor
16 Technicaldata
16.1 Application
16.2 Functionandsystemdesign
16.3 Input
16.4 Output
16.5 Powersupply
16.6 Performancecharacteristics
16.7 Installation
16.8 Environment
16.9 Process
16.10 Mechanicalconstruction
16.11 Operability
16.12 Certificatesandapprovals
16.13 Applicationpackages
16.14 Accessories
16.15 Supplementarydocumentation
17 FlowRatedata
18 FunctionalMatrix
19 TLVEXPRESSLIMITEDWARRANTY
20 Services

Aboutthisdocument EF200F-C
6
1 About this document
1.1 Document function
TheseOperatingInstructionscontainalltheinformationthatisrequiredinvariousphases
ofthelifecycleofthedevice:fromproductidentification,incomingacceptanceand
storage,tomounting,connection,operationandcommissioningthroughto
troubleshooting,maintenanceanddisposal.
1.2 Symbols
1.2.1 Safety symbols
Thissymbolalertsyoutoadangeroussituation.Failuretoavoidthissituationwillresultin
seriousorfatalinjury.
Thissymbolalertsyoutoadangeroussituation.Failuretoavoidthissituationcanresultin
seriousorfatalinjury.
Thissymbolalertsyoutoadangeroussituation.Failuretoavoidthissituationcanresultin
minorormediuminjury.
Thissymbolcontainsinformationonproceduresandotherfactswhichdonotresultin
personalinjury.
1.2.2 Electrical symbols
Symbol Meaning
Directcurrent
Alternatingcurrent
Directcurrentandalternatingcurrent
Groundconnection
Agroundedterminalwhich,asfarastheoperatorisconcerned,isgroundedviaa
groundingsystem.
ProtectiveEarth(PE)
Aterminalwhichmustbeconnectedtogroundpriortoestablishinganyother
connections.
Thegroundterminalsaresituatedinsideandoutsidethedevice:
• Innergroundterminal:Connectstheprotectivearthtothemainssupply.
• Outergroundterminal:Connectsthedevicetotheplantgroundingsystem.
DANGE
R
WARNING
CAUTION

EF200F-C Aboutthisdocument
7
1.2.3 Tool symbols
Symbol Meaning
Flatbladescrewdriver
Allenkey
Open-endedwrench
1.2.4 Symbols for certain types of information
Symbol Meaning
Permitted
Procedures,processesoractionsthatarepermitted.
Preferred
Procedures,processesoractionsthatarepreferred.
Forbidden
Procedures,processesoractionsthatareforbidden.
Tip
Indicatesadditionalinformation.
Referencetodocumentation.
AReferencetopage.
Referencetographic.
Noticeorindividualsteptobeobserved.
1. , 2. , 3. … Seriesofsteps.
Resultofastep.
Helpintheeventofaproblem.
Visualinspection.
1.2.5 Symbols in graphics
Symbol Meaning
1,2,3,... Itemnumbers
1. , 2. , 3. ,… Seriesofsteps
A,B,C,... Views
A-A,B-B,C-C,... Sections
Flowdirection

Aboutthisdocument EF200F-C
8
1.3 Documentation
ForanoverviewofthescopeoftheassociatedTechnicalDocumentation,refertothe
following:
Detailedlistoftheindividualdocumentsalongwiththedocumentationcode
→See16.15
1.3.1 Standard documentation
1.3.2 Supplementary device-dependent documentation
Additionaldocumentsaresupplieddependingonthedeviceversionordered:Always
complystrictlywiththeinstructionsinthesupplementarydocumentation.The
supplementarydocumentationisanintegralpartofthedevicedocumentation.
Documenttype Purposeandcontentofthedocument
InstructionManual
Planningaidforyourdevice
Thedocumentcontainsallthetechnicaldataonthedeviceand
providesanoverviewoftheaccessoriesandotherproductsthat
canbeorderedforthedevice.
TechnicalInformation
BriefOperatingInstructions Guidesyouquicklytothe1stmeasuredvalue
TheBriefOperatingInstructionsareaimedatspecialists
withresponsibilityforinstalling,configuringand
parameterizingthemeasuringdevice(untilthefirstmeasuredvalue).
• Incomingacceptanceandproductidentification
• Storageandtransport
• Installation
• Productdescription
• Electricalconnection
• Operationoptions
• Commissioning
• Diagnosticinformation
DescriptionofDeviceParameters Referenceforyourparameters
Thedocumentprovidesadetailedexplanationofeachindividual
parameterintheExpertoperatingmenu.Thedescriptionisaimedat
thosewhoworkwiththedeviceovertheentirelifecycleandperform
specificconfigurations.
(thisdocument)
Thisdocumentcontainsalltheinformationthatisrequiredin
variousphasesofthelifecycleofthedevice:fromproductidentifica-
tion,incomingacceptanceandstorage,tomounting,connection,
operationandcommissioningthroughtotroubleshooting,
maintenanceanddisposal

EF200F-C Safetyinstructions
9
2 Safety instructions
2.1 Requirements for the personnel
Thepersonnelforinstallation,commissioning,diagnosticsandmaintenancemust
fulfillthefollowingrequirements:
Trained,qualifiedspecialistsmusthavearelevantqualificationforthisspecific
functionandtask.
Areauthorizedbytheplantowner/operator.
Arefamiliarwithfederal/nationalregulations.
Beforestartingwork,readandunderstandtheinstructionsinthemanualand
supplementarydocumentationaswellasthecertificates(dependingonthe
application).
Followinstructionsandcomplywithbasicconditions.
Theoperatingpersonnelmustfulfillthefollowingrequirements:
Areinstructedandauthorizedaccordingtotherequirementsofthetaskbythe
facility'sowner-operator.
Followtheinstructionsinthismanual.
2.2 Designated use
Application and media
Themeasuringdevicedescribedinthismanualisintendedonlyforflowmeasurement
ofliquidswithaminimumconductivityof20µS/cm.
TheEF200F-Cvortexflowmeterisusedtomeasuretheflowofsaturatedsteam,
superheatedsteam,airandwater.Donotusetomeasuretheflowoftoxic,flammable
orotherwisehazardousfluids.
Toensurethatthemeasuringdeviceremainsinproperconditionfortheoperationtime:
Keepwithinthespecifiedpressureandtemperaturerange.
Onlyusethemeasuringdeviceinfullcompliancewiththedataonthenameplateand
thegeneralconditionslistedintheOperatingInstructionsandsupplementary
documentation.
Usethemeasuringdeviceonlyformediatowhichtheprocess-wettedmaterialsare
sufficientlyresistant.
Protectthemeasuringdevicepermanentlyagainstcorrosionfromenvironmental
influences.
Incorrect use
Non-designatedusecancompromisesafety.Themanufacturerisnotliablefordamage
causedbyimproperornon-designateduse.
Dangerofbreakageduetocorrosiveorabrasivefluidsandambientconditions!
Verifythecompatibilityoftheprocessfluidwiththesensormaterial.
Ensuretheresistanceofallfluid-wettedmaterialsintheprocess.
Keepwithinthespecifiedpressureandtemperaturerange.
Residual risks
Theelectronicsandthemediummaycausethesurfacestoheatup.Thispresentsa
burnhazard!
Forelevatedfluidtemperatures,ensureprotectionagainstcontacttopreventburns.
►
►
►
►
►
►
►
►
►
►
►
WARNING
►
WARNING
►
►
►

Safetyinstructions EF200F-C
10
2.3 Workplace safety
Forworkonandwiththedevice:
Weartherequiredpersonalprotectiveequipmentaccordingtofederal/national
regulations.
Forweldingworkonthepiping:
Donotgroundtheweldingunitviathemeasuringdevice.
Ifworkingonandwiththedevicewithwethands:
Duetotheincreasedriskofelectricshock,glovesmustbeworn.
2.4 Operational safety
Risk of injury.
Operatethedeviceinpropertechnicalconditionandfail-safeconditiononly.
Theoperatorisresponsibleforinterference-freeoperationofthedevice.
Conversionstothedevice
Unauthorizedmodificationstothedevicearenotpermittedandcanleadtounforeseeable
dangers.
If,despitethis,modificationsarerequired,consultwithTLV.
Repair
Toensurecontinuedoperationalsafetyandreliability,
Carryoutrepairsonthedeviceonlyiftheyareexpresslypermitted.
Observefederal/nationalregulationspertainingtorepairofanelectricaldevice.
UseoriginalsparepartsandaccessoriesfromTLVonly.
2.5 Product safety
Thismeasuringdeviceisdesignedinaccordancewithgoodengineeringpracticetomeet
state-of-the-artsafetyrequirements,hasbeentested,andleftthefactoryinaconditionin
whichitissafetooperate.
Itmeetsgeneralsafetystandardsandlegalrequirements.ItalsocomplieswiththeEU
directiveslistedinthedevice-specificEUDeclarationofConformity.
ProductconformityisindicatedbytheaffixationoftheCEmarktothedevice.
2.6 IT security
OurwarrantyisvalidonlyifthedeviceisinstalledandusedasdescribedintheOperating
Instructions.Thedeviceisequippedwithsecuritymechanismstoprotectitagainstany
inadvertentchangestothesettings.
ITsecuritymeasures,whichprovideadditionalprotectionforthedeviceandassociated
datatransfer,mustbeimplementedbytheoperatorsthemselvesinlinewiththeirsecurity
standards.
2.7 Device-specific IT security
Thedeviceoffersarangeofspecificfunctionstosupportprotectivemeasuresonthe
operator'sside.Thesefunctionscanbeconfiguredbytheuserandguaranteegreaterin-
operationsafetyifusedcorrectly.Anoverviewofthemostimportantfunctionsisprovided
inthefollowingsection.
►
►
►
►
►
►
►
►

EF200F-C Safetyinstructions
11
2.7.1 Protecting access via hardware write protection
Writeaccesstothedeviceparametersviathelocaldisplayoroperatingtool
canbedisabledviaawriteprotectionswitch(DIPswitchonthemotherboard).
Whenhardwarewriteprotectionisenabled,onlyreadaccesstotheparametersispossible.
2.7.2 Protecting access via a password
Apasswordcanbeusedtoprotectagainstwriteaccesstothedeviceparameters.
Thispasswordlockswriteaccesstothedeviceparametersviathelocaldisplayoranother
operatingtooland,intermsoffunctionality,isequivalentto
hardwarewriteprotection.
User-specific access code
Writeaccesstothedeviceparametersviathelocaldisplayoroperatingtool
canbeprotectedbythemodifiable,user-specificaccesscode(→See10.8.1).
Whenthedeviceisdelivered,thedevicedoesnothaveanaccesscodeandisequivalent
to0000(open).
General notes on the use of passwords
• Theaccesscodeandnetworkkeysuppliedwiththedeviceshouldbechangedduring
commissioning.
• Followthegeneralrulesforgeneratingasecurepasswordwhendefiningandmanaging
theaccesscodeornetworkkey.
• Theuserisresponsibleforthemanagementandcarefulhandlingoftheaccesscodeand
networkkey.
• Forinformationonconfiguringtheaccesscodeoronwhattodoifyoulosethe
password,seethe"Writeprotectionviaaccesscode"section→See10.8.1
2.7.3 Access via fieldbus
Cyclicfieldbuscommunication(readandwrite,e.g.measuredvaluetransmission)witha
higher-ordersystemisnotaffectedbytherestrictionsmentionedabove.

Productdescription EF200F-C
12
2.8 Vibrations
Thecorrectoperationofthemeasuringsystemisnotinfluencedbyplantvibrations
vibrationresistance(→see16.8)Consequently,thesensorsrequirenospecialmeasures
forattachment.Ifhigherlevelsofvibrationareexpected,besuretosecurepiping
beforeandaftertheflowmeter.
2.9 Preventing Excessive Flow
Toensurelongservicelifefortheflowmeter,excessiveinstantaneous/periodicalflow
ratesshouldbeheldbelowtheflowmeterʼsmaximumflowrate.Failingtodosomight
resultindamagetothesensor.Specialcareisnecessaryforsteamatstartupwhenthe
pressureislow,orwhenavalveisopenedrapidly,suchasbyasolenoidvalve,as
excessiveinstantaneousflowratesoftenoccur.
2.10 Pulsating Influences
Theabilityoftheflowmetertomeasurecorrectlymaybeadverselyaffectedifthereare
largevariationsofpressureorpulsatingpressurefromcompressorsand/orsootblow-
ers.Usetheproceduresbelowtominimizepulsatingpressures:
•Movethesourceofthepulsationstothedownstreamsideoftheflowmeter.Alterna-
tively,putasmuchdistanceaspossiblebetweenthesourceandtheflowmeter.
•Installapulsationdampeningdevice,suchasachamber.
•Closethevalvesbeforeandaftertheflowmeterwhenthereisnoflow.(Thisisto
preventfalsenon-zeroreadingsunderzero-flowconditions.)
2.11 Prevent Mixed Phase Flow
Thisflowmeterisdesignedtomeasurebothgasesandliquids.However,accurate
measurementcannotbeguaranteedwhengasesandliquidsaremixedtogether(i.e.
gas-liquidmixedphaseflow).
2.12 Ensure Pipe is Flooded
Whenmeasuringliquidsensurethatthepipeisflooded,asthiswillhaveaninfluenceon
theaccuracyofflowratemeasurements.
2.13 Bypass Lines
Theinstallationofbypasslinescanfacilitatemaintenanceandinspections.When
installingabypassline,useupstreamanddownstreamvalvesofatypethatdoesnot
disturbtheflowprofile,andsecuresufficientlengthofstraightpipe.

3 Product description
Thedeviceconsistsofatransmitterandasensor.
Twodeviceversionsareavailable:
• Compactversion‒transmitterandsensorformamechanicalunit.
• Remoteversion-transmitterandsensoraremountedinseparatelocations.
3.1 Product design
12
3456
78
9
+E
–
A0020649
Importantcomponentsofameasuringdevice
1 Electronicscompartmentcover
2 Displaymodule
3 Mainelectronicsmodule
4 Cableglands
5 Transmitterhousing(incl.HistoROM)
6 I/Oelectronicsmodule
7 Terminals(springloadedterminals,pluggable)
8 Connectioncompartmentcover
9 Sensor
EF200F-C Productdescription
13
1
A0034152
Versionsofpressuremeasuringunit
1 Ordercodefor"Sensorversion;DSCsensor;measuringtube",option"Masssteam"
Forordercodefor"Sensorversion;DSCsensor;measuringtube",option"Mass
steam",thefollowingapplies:Oil-freeorgrease-freecleaningisnotpossible

Incomingacceptanceandproductidentification EF200F-C
14
4 Incoming acceptance and product identification
4.1 Incoming acceptance
1
Arethegoodsundamaged?
Istheenvelopepresentwith
accompanyingdocuments?
Aretheproductsticker(1)
idential?
• Ifoneoftheconditionsisnotsatisfied,contactyourTLVSalesCenter.
• ContactTLVforTechnicalDocumentation.

EF200F-C Incomingacceptanceandproductidentification
15
4.2 Product identification
Thefollowingoptionsareavailableforidentificationofthedevice:
• Nameplatespecifications
• Ordercodewithbreakdownofthedevicefeaturesonthedeliverynote
ForanoverviewofthescopeoftheassociatedTechnicalDocumentation,refertothe
following:
4.2.1 Transmitter nameplate (compact version)
A0032237
1
F
1
2
3
5
4 
6
7
1
2Nameofthetransmitter
3
Modelname
4
Serialnumber(ser.no.)
5
6
7
Permittedambienttemperature
Degreeofprotection
Permittedfluidtemperature
Powersupplyvoltage

Incomingacceptanceandproductidentification EF200F-C
16
4.2.2 Sensor nameplate (remote version)
1
2Nameofthetransmitter
3
Modelname
4
Serialnumber(ser.no.)
5
6
7
Permittedambienttemperature
Degreeofprotection
Permittedfluidtemperature
Powersupplyvoltage
Transmitter
1
2Nameofthetransmitter
3
Modelname
4
Serialnumber(ser.no.)
5
6
7
Permittedambienttemperature
Degreeofprotection
Permittedfluidtemperature
Powersupplyvoltage
Sensor

1
2
3
5
4 
6
7
F
7
2
3
5
6
4
1
F

EF200F-C Incomingacceptanceandproductidentification
17
4.2.3 Nameplate for TEG (compact version/remote version)
Ordercode:
Ser.no.:
Ext.ord.cd.:
TTa+20K
skrowxe:WF
Date:
330820-0001B
O7F2C50-1234/56
S201EA19000
DC9...32V/2-wire
4-20mAHART
Pulse/freq./switchoutput
4-20mAInput
1xplug,1xsocketM12x1
Ta:-20...+60
V1.00.00
IP66/67Type4Xencl.
2021-02 A
VORTEXFLOWMETEREF200-C
Profile:3.02
1
6
2
3
4

5

1
2Nameofthetransmitter
3
Modelname
4
5
6
Electricalconnectionthread
Degreeofprotection
Powersupplyvoltage
Permittedambienttemperature

Storageandtransport EF200F-C
18
5 Storage and transport
5.1 Storage conditions
Observethefollowingnotesforstorage:
Storeintheoriginalpackagingtoensureprotectionfromshock.
Donotremoveprotectivecoversorprotectivecapsinstalledonprocessconnections.
Theypreventmechanicaldamagetothesealingsurfacesandcontaminationinthe
measuringtube.
Protectfromdirectsunlighttoavoidunacceptablyhighsurfacetemperatures.
Storeinadryanddust-freeplace.
Donotstoreoutdoors.
Storagetemperature:‒50to+80˚C(‒58to+176˚F)
5.2 Transporting the product
Transportthemeasuringdevicetothemeasuringpointintheoriginalpackaging.
A0029252
Donotremoveprotectivecoversorcapsinstalledonprocessconnections.They
preventmechanicaldamagetothesealingsurfacesandcontaminationinthe
measuringtube.
5.2.1 Measuring devices without lifting lugs
Centerofgravityofthemeasuringdeviceishigherthanthesuspensionpointsofthe
webbingslings.
Riskofinjuryifthemeasuringdeviceslips.
Securethemeasuringdeviceagainstslippingorturning.
Observetheweightspecifiedonthepackaging(stick-onlabel).
A0029214
WARNING
►
►
►
►
►
►
►

EF200F-C Storageandtransport
19
5.2.2 Measuring devices with lifting lugs
Specialtransportationinstructionsfordeviceswithliftinglugs
Onlyusetheliftinglugsfittedonthedeviceorflangestotransportthedevice.
Thedevicemustalwaysbesecuredattwoliftinglugsatleast.
CAUTION
►
►

Installation EF200F-C
20
6 Installation
6.1 Installation conditions
6.1.1 Mounting position
Mounting location
A0015543
Orientation
Thedirectionofthearrowonthesensornameplatehelpsyoutoinstallthesensor
accordingtotheflowdirection(directionofmediumflowthroughthepiping).
Vortexmetersrequireafullydevelopedflowprofileasaprerequisiteforcorrectvolume
flowmeasurement.Therefore,pleasenotethefollowing:
Orientation Compactversion Remoteversion
A Verticalorientation
A0015545
1)
B Horizontalorientation,transmitterheadup
A0015589
2)3)
C Horizontalorientation,transmitterheaddown
A0015590
4)5)
D Horizontalorientation,transmitterheadatside
A0015592
1) Inthecaseofliquids,thereshouldbeupwardflowinverticalpipestoavoidpartialpipefilling(Fig.A).
Disruptioninflowmeasurement!Inthecaseofverticalorientationanddownwardflowingliquid,thepipe
alwaysneedstobecompletelyfilledtoensurecorrectliquidflowmeasurement.
2) Dangerofelectronicsoverheating!Ifthefluidtemperatureis侒200˚C(392˚F),orientationBisnot
permittedforthewaferversion(EF200W-C)withnominaldiametersofDN100(4")andDN150(6").
3) Inthecaseofhotmedia(e.g.steamorfluidtemperature(TM)侒200˚C(392˚F):orientationCorD
4) Inthecaseofverycoldmedia(e.g.liquidnitrogen):orientationBorD
5) For"wetsteamdetection/measurement"option:orientationC
㾎㾎㾎㾎
㾎㾎㾎㾎
㾎㾎㾎㾎
4)
㾎㾎㾎㾎