TMS ST Series User manual

ST-1000-D1 LIGHTING CONTROLLER UNIT
ST Series Lighting
Controller
ST-1000-D1
(CONSTANT AND TRIGGER MODE)
USER MANUAL
Rev 1.0 20OCT 2016

ST-1000-D1 LIGHTING CONTROLLER UNIT
- i-
Contents
Introduction ..............................................................................................................................................1
Features List .........................................................................................................................................1
Applications..........................................................................................................................................1
Hardware..................................................................................................................................................2
Packing List..........................................................................................................................................2
Front Panel ...........................................................................................................................................2
Configuration........................................................................................................................................3
Connections......................................................................................................................................3
Current DIP Switch Settings.................................................................................................................5
Power ON.............................................................................................................................................6
Operation Mode....................................................................................................................................6
Constant Mode .................................................................................................................................6
Trigger Mode....................................................................................................................................6
ST-1000-D1 Specification........................................................................................................................7
Dimension Layout ....................................................................................................................................8
Simple Connection ST-1000-D1 ..............................................................................................................8
Cable Information.....................................................................................................................................9
Power Cord Information.........................................................................................................................10
Lighting Connector of SM......................................................................................................................11
Revision Notes
Rev
Date/Author
Comment
1.0
ZW
First Release

ST-1000-D1 LIGHTING CONTROLLER UNIT
- 1-
Introduction
Features List
1 channel lighting controller card with VR and Selection Switch
Voltage control for channel up to 24V DC
Lighting output voltage 24VDC
Current Selection 200mA, 400mA, 700mA, 700mA and up to 2A
Default current output is 200mA (Maximum Output Current 2A)
Trigger intensity control
Din Rail/ Panel Mount
Applications
Light Control for Selectable Mode (Constant and Trigger)
General purpose light intensity control ( Constant and Trigger Mode )

ST-1000-D1 LIGHTING CONTROLLER UNIT
- 2-
Hardware
Packing List
Please make sure that the following parts are in the packing list:
ST-1000-D1 lighting controller unit
Adaptor +24V with Power Cord 110 - 240 (Optional)
LED Lightings (Optional)
Ext. Lighting Cable (Optional)
Rear Plate with Din Rail Clip
Front Panel
The front panel consists of VR KNOB (Constant / Trigger LED Intensity Control) and
Slide Switch (Selectable Constant Mode or Trigger Mode).

ST-1000-D1 LIGHTING CONTROLLER UNIT
- 3-
Configuration
Connections
For ST-1000-D1 to operate properly, the unit terminals must be connected correctly.
The terminals voltage polarity must be followed accordingly to prevent damage to the
unit.
Board Power Terminals
These terminals are to be connected to a 24V DC power supply with minimum
500mA capability.
Lightings Output Terminals
These terminals are to be connected to 24V-Lightings for a 24V DC power supply
at Lightings Input Power Terminals.
Trigger Input Terminals
For Trigger Mode operation, these terminals are to be connected to trigger signal
line from external control unit. Trigger voltage range from 5V to 24V DC.
For Constant Mode operation, these terminals can be left unconnected.
LEFT VIEW: RIGHT VIEW:
Lightings Output
Terminals
Trigger Input
Terminals
(5V to 24V DC)
Board Power
Terminals
(24V DC)

ST-1000-D1 LIGHTING CONTROLLER UNIT
- 4-
TOP VIEW
-At Top View, the ST Control card, all the Positive terminals are with ‘+’
label and the Negative terminals are with ‘-’ label, as shown in the above
photo.
VR KNOB Control
LED Intensity
Constant and Trigger
Select Switch

ST-1000-D1 LIGHTING CONTROLLER UNIT
- 5-
Current DIP Switch Settings
The DIP Switches is located at the lower right of the controller as shown in the photo
below.
The DIP Switches sets the maximum output current to the Lighting Output for over
current protection.
Factory default setting is 700mA.
Caution: Make sure the selected maximum current output is suitable for the lightings to
prevent damage to both the lightings and the ST lighting controller unit.
Switch
Output Current (mA)
1
(200mA)
2
(400mA)
3
(700mA)
4
(700mA)
OFF
OFF
OFF
OFF
INVALID
ON
OFF
OFF
OFF
200
OFF
ON
OFF
OFF
400
OFF
OFF
ON
OFF
700
ON
OFF
ON
OFF
900
OFF
ON
ON
OFF
1100
OFF
OFF
ON
ON
1400
OFF
ON
ON
ON
1800
ON
ON
ON
ON
2000
DIP Switch Settings for Maximum Lighting Output Current
Current Selector

ST-1000-D1 LIGHTING CONTROLLER UNIT
- 6-
Power ON
The default current setting for the ST controller is 700mA. If other current settings are desired,
please refer to the previous section before power on the unit.
Connect the lighting connectors to the lighting connection terminals.
Connect a voltage supply from 24V DC to the Board Power Terminals. The POWER LED will
lit when power is supplied.
Operation Mode
There are two functional modes for ST-1000-D1:
Constant Mode
Trigger Mode
Constant Mode
The unit will operate in Constant Mode when the slide switch is set at “CONSTANT” position
(Label CONSTANT). The unit has constant mode intensity from 0 to 10 (Analog).
Set the slide switch at “CONSTANT” position.
The Lightings intensity is set by manually adjust the position of VR Knob (label 0-10) on the
casing.
When VR Knob position at '0', it sets the lightings intensity at minimum.
When VR Knob position at '10', it sets the lightings intensity at maximum.
Trigger Mode
The unit will operate in Trigger mode when the Toggle switch is set at “STROBE” position
(Label STROBE). The unit has trigger mode intensity from 0 –10 (Analog).
Set the Toggle switch at “STROBE” position.
The Lightings intensity is set by manually adjust the position of VR Knob (label 0-10) on the
casing.
When VR Knob position at '0', it sets the lightings intensity at minimum.
When VR Knob position at '10', it sets the lightings intensity at maximum.
The “STROBE SIGNAL” input and “LIGHT OUTPUT” output timing diagram is shown as
below:
Triggered Mode Timing

ST-1000-D1 LIGHTING CONTROLLER UNIT
- 7-
Pull High / Pull Low
ST-1000-D1 Specification
CONTROL:
VR
Manual Control (Adjustable)
General:
Dimension
78mm x 40.50 x 53.4mm
Power Input
+24 VDC
Board Max Power Consumption
50mA±10% @ 24V
Board Voltage
24 VDC
Channels:
1 Channels
Channel Control
Independent
Output Mode
Constant / Trigger
Output Current
700mA (Default),
200mA, 400mA, 700mA, 900mA,1100mA, 1400mA,
1800 & up to 2000mA
Lighting Input and
Output Voltage
24VDC
Functions:
Constant
Lighting Intensity
VR Adjustable
Intensity Range
0 ~ 10 steps
Trigger
Lighting Intensity
VR Adjustable
Intensity Range
0 ~ 10 steps
Timing Delay
0 ~ 100 ns
External I/O:
Input
Input Voltage
5~24 VDC
Input Current
5 VDC
1.4 mA (typical)
12 VDC
4.5 mA (typical)
24 VDC
10 mA (typical)
Protection
2500 VDC Opto-coupler Isolation

ST-1000-D1 LIGHTING CONTROLLER UNIT
- 8-
Dimension Layout
Simple Connection ST-1000-D1

ST-1000-D1 LIGHTING CONTROLLER UNIT
- 9-
Cable Information
i) EXT-24V-F-3M
Extension Cable of 3 Meter with SM connector
ii) EXT-24V-F-3M-TB
Extension Cable of 3 Meter with Terminal Block connector

ST-1000-D1 LIGHTING CONTROLLER UNIT
- 10 -
Power Cord Information
The cable length is 1.8 Meter length of power cord.
240VAC Power Cord (UK)
220VAC Power Cord (EU)
110VAC Power Cord (US)

ST-1000-D1 LIGHTING CONTROLLER UNIT
- 11 -
Lighting Connector of SM
Pin 1 -- Red wire (+ve) Pin 3 -- White wire (-ve)

Thank you for downloading this document from
www.machine-vision-shop.com
If you have any questions, you need help composing the
right package for your application or do you want to order?
Feel free to contact us via e-mail at sales@vision-
consultancy.nl or visit our webshop.
Our vision experts are happy to help you.
VISION CONSULTANCY
Robert Schumandomein 2
6229 ES Maastricht
The Netherlands
[phone]
[email protected]
www.machine-vision-shop.com
Natascha Overhof
Christian Crompvoets
© 2021 Vision Consultancy
Scan me to visit
machine-vision-shop