TMT Automation Marble Series User manual

Marble SERIES
Garage Door Openers
USER MANUAL

GARAGE DOOR OPENERS USER MANUAL 2
INDEX
1. Warnings
2. Product description
2.1 Applications
2.2 Description of the automation
3. Installation
3.1 Inventory of a garage door opener
3.2 Rail assembly
3.3 Attach the rail to the motor
3.4 Attach the rail on the header wall and ceiling
3.5 Connect release section to the garage door
3.6 Final steps before system learning
3.7 Introduction of the emergency release
4. Operation
4.1 Accessory connection
4.2 Door position for start-up phase
4.3 Transmitter memorizing and erasing process
4.4 System learning, reset process, and LED display
4.5 Programmable function indication LED
4.6 How to set the parameter
4.7 Programmable function setting
5. Function of terminals
5.1 Photocells
5.2 Installation of Photocells
6. Specification
7. Wi-Fi Box User Manual
8. Accessory
2
3
3
3
4
4
5
6
6
7
8
8
9
9
9
10
10
12
12
13
14
14
14
15
16
17
1. WARNINGS
WARNING :
Please read this instruction manual carefully before the installation.
This manual is exclusively for qualified installation personnel. TMT Automation Inc. is not responsible for
improper installation and failure to comply with local electrical and building regulations.
Keep all the components for the garage door opener and this manual in hand for further consultation.
● In this manual, please pay extra attention to the contents marked by the symbol:
● Be aware of the hazards that may exist in the procedures of installation and operation of the garage door opener.
Besides, the installation must be carried out inconformity with local standards and regulations.
● If the system is correctly installed and followed all the regulations, it will ensure a high degree of security.
● Make sure that the door works properly before installing the garage door opener and confirm the doors are
appropriate for the application.
● Do not let children operate or play with the garage door opener.
● Do not cross the path of the garage door opener when it is in operation.
● Please keep all the control devices and any other pulse generator away from children to avoid the system being
activated accidentally.
● Do not make any modifications to any components except that it is mentioned in this manual.
● Do not try to manually open or close the doors before you release the opener.
● If there is a failure that cannot be solved and is not mentioned in this manual, please contact a professional installer.
● Do not use the garage door opener before all the procedures and instructions have been carried out and
thoroughly read.
● Install warning signs (if necessary) on the both sides of the door to warn the people in the area of potential hazards.

GARAGE DOOR OPENERS USER MANUAL
3
Operation buttons: Remote Function key (RF),
Setting key (Set), UP key (Up), DOWN key (Down).
Connection terminal of Optional accessories
Radio receiver board
Fuse
Wi-Fi Box
The power indicator is on the bottom right of the display. When the motor
is powered, the LED dot indicator is alight.
When entering to the power-saving mode, the LED power indicator is
flashing ( light for 0.5 second and then no light for 5 seconds )
2). The indication of control panel
3). The LED indication
1
1
2
2
3
4
5
2. PRODUCT DESCRIPTION
2.1 APPLICATIONS
Garage door opener is applied for residential automation of up and over doors and sectional doors. It has to be operat-
ed with electricity. It’s forbidden to be operated by back-up batteries for normal use.Back-up batteries are only allowed
for emergent operation when there is a power failure, and the carriage can be released by pulling the cord to move the
door manually.
Garage Door Opener
Photocells (Optional accessories)
Flashing Light (Optional accessories)
Key selector (Optional accessories)
Push Button (Optional accessories)
Transmitter
2.2 DESCRIPTION OF THE AUTOMATION
1). The following diagram of typical installation describes some terms and accessory of the door automation
system:
1
2
3 4
EXT- EXT+ LIT- LIT+ PB GND PH +24V GND +BATT
5
1
1
2
22
3
3
4
4
5
5
6
6

GARAGE DOOR OPENERS USER MANUAL 4
3. Installation
3.1 Inventory of a garage door opener
Front hold
C Rail Rear Pulley Support Front Pulley
Tensioner
Release Rope
Blocker x1
Bracket Bracket
Header bracket Door Bracket Ceiling Bracket
Bent Arm Straight Arm
Ceiling Support Bracket
1
13108
4
19 20 21 22
23 24 25
23
17
6 7
11 12
5
18
14 15
Hardware Inventory
M8*20
HEX bolt x4
M6*14
HEX bolt x4
M8*8 Nut x4 M6*6 Nut x8Clevis Pin x2
Locking
Plate
x2 Screws
x4
9
Long Clevis Pin
Cotter Pin
26
27
Door Bracket Locator
16
Junction x2
28
Optional for 1pcs x 1M Rail

GARAGE DOOR OPENERS USER MANUAL
5
Chain and index
Inner trolly assy
Assemble the front and middle rail with the
junction, and make sure it is located at the middle
of the protruding point.
Assemble the back and middle rail with another junction,
and make sure it is located at the middle of the
protruding point.
Remove the nut and the spring in the (4) Front pulley tensioner. Make sure the metal chain is placed in the gap of the
pulley on the two sides. Insert the (2) Front hold bracket against the rail. Use the spring and the nut to adjust the
tightness of the (5) Chain.
Note: Remember to lubricate the front and rear pulley before use.
3.2 Rail assembly
28
28
6
4
2
4
5
Completion
1
2
3
4
4
8
1. The (6) Inner trolly assy and the (5) Chain and index are already in the Rail.
2. Make sure the metal index is on right side of the rail.
3. Fasten the (8) Outer trolly assy on the (6) Inner trolly assy with (18) Screws 4pcs
5
65 6
18

GARAGE DOOR OPENERS USER MANUAL 6
3.3 Attach the rail to the motor
CAUTION
3.4 Attach the rail on the header wall and ceiling
1. Position (11) Header bracket on the header wall.
* It is recommended to align the (11) Header bracket with the horizontal center of the door
*It is recommended to position the (11) Header bracket at a height 30-50cm from the top of the door.
2. Install the (11) Header bracket with screws.
3. Attach the front rail to header bracket with bolts.
4. Attach the (13) Ceiling bracket on the crossbeam of ceiling with crews.
1. Connect the (3) Rear pulley support to the output shaft of the motor.
2. Fasten the rail on the motor with (9) Motor hold bracket and the (25) Hex nuts.
3. Fasten the (10) Ceiling hold bracket and (13) Ceiling bracket at the rear side between the motor
and the rear blocker with Hex bolt (21) and Hex nuts (24).
Remark: Optional choice is to use L-bracket to hold the brackets to the ceiling, and fasten to
both the ceiling and ceiling bracket(13) using Hex bolt(22) and Hex nuts(25).
Attach Rail to the Header Bracket
To prevent damage, place the garage door on the top
section to create a temporary support.
Garage
Door
Header Bracket
Header
These are not
included in the
hardware inventory
Bracket
Long Clevis
Pin
Cotter Pin
(11)
(11)
Rail
Door 2x4 is used to determine
the correct mounting height
from ceiling.
Ceiling
bracket
24
Nut
13
10
3
1
Ceiling
hold bracket
2
Motor
hold bracket
9
Nut25
HEX bolt
21

GARAGE DOOR OPENERS USER MANUAL
7
3.5 Connect release section to the garage door
ENGAGED
Secure handle with overhand knot
and heat seal rope.
Connect the (7) Emergency release rope on the
(8) Outer trolley assy
RELEASED
Overhand
Knot
Rope
7 Emergency
Release Handle
1
NOTE: Handle should hang 6 feet (1.5 m) above floor.
Ensure that the rope and handle clear the tops of all
vehicles to avoid entanglement.
To prevent possible SERIOUS INJURY or DEATH from a falling
garage door:
• If possible, use emergency release handle to disengage trolley ONLY
when garage door is CLOSED. Weak or broken springs or
unbalanced door could result in an open door falling rapidly and/or
unexpectedly.
• NEVER use emergency release handle unless garage doorway is
clear of persons and obstructions.
• NEVER use handle to pull door open or closed. If rope knot
becomes untied, you could fall.
WARNING
Pull the (7) Release rope to disengage the
(8) trolley
Fasten the (12) Door bracket and (16) Door bracket locator
on the center of the garage door. Connect (14) Curved arm
to (12) Door bracket.
Connect (15) Straight door arm to Release trolley
Connect the (14) Curved arm and
the (15) straight arm with bolts and nuts.
3
Pull Down
to Release
Trolley
45
CONNECT DOOR ARM TO TROLLEY
2
15
Straight
Arm
23
Clevis Pin
19
Locking Plate
(not included in the hardware inventory)
Door bracket locator
is used when door
panel is required
19
(12)+(16)
23
Connect Curved
Arm to Door Bracket
Clevis Pin
Locking Plate
Nut
Hex Bolt
14
24
21
15
Curved
Arm
Straight
Arm
50cm

GARAGE DOOR OPENERS USER MANUAL 8
3.6 Final steps before the system learning
3.7 Introduction of the emergency release
1. Install the (18) Blocker at the door open position.
2. Attach the warning sign to the (7) Emergency release rope.
3. Connect the power to the motor. Ensure the electric plug and socket are well connected.
1. Pull the (7) Emergency release rope to release the trolley. Make sure the trolley is disengaged. The garage door can be
operated manually.
2. Before restarting the motor, manually move the garage door until the trolley is engaged.
To prevent possible SERIOUS INJURY or DEATH from
electrocution or fire:
• Ensure power is not connected to the opener, and
disconnect power from the circuit BEFORE removing
cover to establish permanent wiring connection.
• Garage door installation and wiring ARE in
compliance with all local electrical and building codes.
• NEVER use an extension cord, 2-wire adapter, or
change plug in ANY way to make it fit an outlet.
Ensure the opener is grounded.
WARNING
2 3
1
18
Blocker
RED
RELEASE
CORO
RED EMERGENCY
RELEASE KNOB
Pull Down
to Release
Trolley

GARAGE DOOR OPENERS USER MANUAL
9
4. Connection
4.1 Accessory connection
A. Open the cover in order to access the electronic connection terminal of the garage gate opener.
B. Connect the wires of each accessory to the terminal.
Only establish electrical connections when the electricity supply to the system is OFF.
4.2 Door position for start-up phase
1. Use a commercial adaptor if the plug on the Marble Series unit does not correspond to the socket
available.When the system is powered up, check if the LED is ON.
2. Never cut or remove the cable supplied with the Marble Series garage opener. The power socket of Marble garage opener
connection must be fitted by skilled and qualified personnel in strict observance of current legislation,
standards and regulations.
3. The power supply line must be protected from short circuits and ground leakage.
4. The garage door is recommeded to be set at half travel.
This will ensure the leaf is free to move both during opening and closure.
External Device Flashing Light Push Button Photocell Battery
C. Function of external push button:
Door operation when pressing the push button: open-stop-close-stop
EXT- EXT+ LIT- LIT+ PB GND PH +24V GND +BATT
1RX1 2 3
EXT- EXT+ LIT- LIT+ PB GND PH +24V GND +BATT
4
TX1
56

GARAGE DOOR OPENERS USER MANUAL 10
4.3 Transmitter memorizing and erasing process
A. Transmitter Memorizing:
Press “RF Learn” button for 3 seconds, and the LED display will show “CS”; then press the transmitter A
button within 10 seconds; “CS” will blink three times and stay ON After 10 seconds without any movement,
“CS” will disappear The transmitter learning is completed.
B. Erasing Transmitter Memory:
Press and hold "RF Learn" button for 10 seconds, the display will show “CS”. When “CC” is displayed, the memory is cleared.
C. Memorizing an additional transmitter by a memorized one:
Press and hold A and B buttons for 5 seconds, LED light and external flash light will blink at the same time. Within 10 seconds, press
any button on the un-memorized transmitter for 2 seconds, the transmitter will be memorized after LED light and external flash light
are off. To program by memorized transmitter, just can do the transmitter learning one by one.
4.4 System learning, reset process, and LED display
A. System Learning:
Step1: Press and hold “RF” and “SET” buttons for 3 seconds, the LED display shows “OL” and the motor enters the system
learning program.
Step2: Set the open limit and LED shows “OL”. Press and hold “UP” or “DOWN” button to adjust the door. When the door is
at the proper open position, press “SET” button.
Step3: Set the close limit and LED shows “CL”. Press and hold “UP” or “DOWN” button to adjust the door. When the door
is at the proper close position, press “SET” button.
Step4: When the LED shows “GE”. Press “SET” button to proceed operation testing. The LED will show the operation
current value in the process and memorize overcurrent value.
Step5: The motor opens and closes automatically with full speed. The LED shows “SO” while the system learning is
completed. Otherwise, the LED will show “SF" when the system learning is failed. The LED will be off after 10
seconds.
Note: The overcurrent function and flashing light function will be activated automatically after the learning process is
completed.
A B
3 SEC
Within 10 sec
10 SEC
A B A B
Within 10 sec
Memorized
Transmitter

GARAGE DOOR OPENERS USER MANUAL
11
B. Return to the Default Setting:
Press “RF” and “DOWN” buttons for 3 seconds, and the whole setting will be defaulted when the LED shows “CL”.
C. Motor current auto-detection
The LED shows the current consumption of the motor
During the system learning process, the control panel will automatically detect the
current consumption from each motor, indicate the resistance level of the gate
whiling the motor operation. If this reading increase instantly or stay in high
reading, please DO check if any object is in between the gate moving area, and
contact your installer for further inspection.
3 SEC
Step.1
Step.3 Step.4
Step.5
Step.2
3 SEC
Default Setting

LED Display Programmable Functions LED Display Programmable Functions
4.5 Programmable function indication LED
Start transmitter learning mode. Operation testing
Cleaned all studied transmitter. System Learning Fail.
Set up Open Limit. System Learning Completely.
Set up Close Limit. System setting clear
4.6 How to set the parameter:
Step 1: Press the“Set” key for 3 seconds, the LED will show the function code.
Step 2: Choosing the function by “Up” or “Down” keys. Press the “Set” key to enter the setting of parameters. Please
refer to the following sections for further details of the function setting
GARAGE DOOR OPENERS USER MANUAL 12
3 SEC
Confirm
Confirm

4.7 Programmable function setting
LED Display Definition Function Value Description
Deceleration Point
(% full operation)
Main Operation Key
Lighting Key
External Device Key
Photocell Function Mode
PH Terminal
Alarm Buzzer
Auto-closing
Lighting
Overcurrent reaction
Overcurrent setting
1
2
3
4
5
6
7
8
9
A
1-1
1-2
1-3
1-4
1-5
2-0
2-1
2-2
2-3
2-4
3-0
3-1
3-2
3-3
3-4
4-0
4-1
4-2
4-3
4-4
5-0
5-1
5-2
6-1
6-2
7-1
7-2
7-3
7-4
7-5
7-6
7-7
7-8
7-9
8-1
8-2
8-3
8-4
9-1
9-2
9-3
1-0
2-0
3-0
4-0
5-0
6-0
7-0
8-0
9-0
9-9
75%
80%
85%
90%
95%
Function off
A Key
B Key
C Key
D Key
Function off
A Key
B Key
C Key
D Key
Function off
A Key
B Key
C Key
D Key
Function off
Mode 1
Function off
Function on
Function off
30 sec
60 sec
90 sec
120 sec
150 sec
180 sec
210 sec
240 sec
Function off
LED light starts running 1 minute
LED light starts running 2 minutes
LED light starts running 3 minutes
Stop when over-current
Reverse 2 seconds when over-current
Reverse to the end when over-current
Learning current add 0.2A as overcurrent
Learning current add 0.4A as overcurrent
Learning current add 0.5A as overcurrent
Learning current add 0.6A as overcurrent
Learning current add 0.8A as overcurrent
Learning current add 1.0A as overcurrent
Learning current add 1.2A as overcurrent
Learning current add 1.4A as overcurrent
Learning current add 1.6A as overcurrent
Learning current add 1.8A as overcurrent
1.The default setting is "1-3"
1.The default setting is "2-1"
1.The default setting is "3-2"
1.The default setting is "4-3"
1.The default setting is "5-0 "
2. Please refer to page 14_Function of photocells
1.The default setting is "6-1"
2. IF the door left opened for longer than 10mins then buzzer
start beeping and turn off until the door been closed.
1.The default setting is "7-1"
1.The default setting is "8-4"
1.The default setting is "9-2"
1. The default setting is "3-0"
Mode 2
GARAGE DOOR OPENERS USER MANUAL
13

5. Function of external accessory
Gate Status
Closed
Opened
Stop during moving
Closing
Opening
The reactions of the photocells when obstacles are detected
No effect
1. Stop till next command is given
2. Stop and reload the auto-closing time if the auto-closing feature is on
1. Stop till next command is given
2. Stop and reload the auto-closing time if the auto-closing feature is on
Stop till next command is given
Stop till next command is given
Gate Status
Closed
Opened
Stop during moving
Closing
Opening
The reactions of the photocells when obstacles are detected
No effect
1. Stop till next command is given
2. Stop and reload the auto-closing time if the auto-closing feature is on
1. Not allow to close till next command is given
2. Not allow to close and reload the auto-closing time if the auto-closing feature is on
Stop till next command is given
No effect
5.1 Photocells
F5-1 Mode 1
F5-2 Mode 2
LED Display Definition Function Value Description
Overcurrent setting of open
limit
Overcurrent setting of close
limit
Power supply for +24V
terminal
C
E
F
C1
C2
C3
C4
C5
C6
C7
E1
E2
E3
E4
E5
E6
E7
F1
F2
2A as overcurrent value of open limit
3A as overcurrent value of open limit
4A as overcurrent value of open limit
5A as overcurrent value of open limit
6A as overcurrent value of open limit
7A as overcurrent value of open limit
8A as overcurrent value of open limit
2A as overcurrent value of close limit
3A as overcurrent value of close limit
4A as overcurrent value of close limit
5A as overcurrent value of close limit
6A as overcurrent value of close limit
7A as overcurrent value of close limit
8A as overcurrent value of close limit
Continuously power supply
Sleep mode
1. The default setting is "C-3"
1. The default setting is "E-3"
1. The default setting is "F-1"
2. Sleep mode: Power supply only when motor is
operating
GARAGE DOOR OPENERS USER MANUAL 14

15 GARAGE DOOR OPENERS USER MANUAL
5.2 Installation of Photocells
INSTALLATION:
1. Open the cover and connect the wires.
2. Mount the receiver and transmitter on the proper position.
3. Ensure there are no obstacles between receiver and transmitter.
For optimal efficiency, the receiver and transmitter should be properly aligned.
4. Power-up the photocells and make sure the LED light on receiver and transmitter are ON.
The safety photocells are security devices to control automatic gates. It’s consist of one transmitter and one
receiver set in the waterproof covers. It will be triggered when the path of the beam is blocked.
Lens
Power LED
Indicator
Terminal Block
Power
Terminal Block
TX RX
SPECIFICATION:
Step 1 Step 2 Step 3 Step 4
12345
COMNCNO
+ -
+
-
12
Detection Method
Sensing Range
Input Voltage
Contact Current
Response Time
Emitting Element
Operation Indicator
Dimensions
Output Method
Current Consumption
Connection Method
Housing Material
Water Proof
Safety Standard
Through Beam
MAX~15m
AC/DC 12~24V
TX: 30mA Max , RX: 25 mA Max
<100mS
Infrared LED/ Wave Length ：940nm
RX：Red LED On (beam broken) / Off (beam aligned)
TX：Red LED On
63*63*30 mm
Relay Output
Beam aligned ：RX<25ma\TX<30ma
Beam broken ：RX <10ma\TX <30ma
Terminal Block
ABS / PC
IP54
CE
EXT- EXT+LIT- LIT+
PB GND PH +24V GND +BATT

GARAGE DOOR OPENERS USER MANUAL 16
6. Specification
7.Marble Online User Manual
Volt
Motor volt
Power
Force
Remote frequency
Max door area
Temperature range
Rail length
Running speed
AC 220V / 110V ;
50Hz~60Hz
DC24V
72W
600N
433.92MHZ
8-10m²
-20oC ~ +50oC
3.0m/3.3m
140mm/sec
AC 220V / 110V ;
50Hz~60Hz
DC24V
80W
800N
433.92MHZ
10-12m²
-20oC ~ +50oC
3.0m/3.3m
140mm/sec
AC 220V / 110V ;
50Hz~60Hz
DC24V
100W
1000N
433.92MHZ
12-14m²
-20oC ~ +50oC
3.0m/3.3m
140mm/sec
AC 220V / 110V ;
50Hz~60Hz
DC24V
120W
1200N
433.92MHZ
14-16m²
-20oC ~ +50oC
3.0m/3.3m
140mm/sec
Garage Door Opener MARBLE60 MARBLE80 MARBLE100 MARBLE120
www.tmt-automation.com/marble_manual_en
Marble
User Manual

GARAGE DOOR OPENERS USER MANUAL
17
8. Accessories
TM3 Transmitter
Frequency
Coding
Buttons
Power Supply
Operating Temperature
Dimension
433.92Mhz
Rolling code
4 buttons
3V with one CR2032 button type lithium battery
-20°C~+50°C
37*67.5*12 (mm)
FL2 Flashing Light
Voltage
Operating Temperature
Installation
Dimension
24V DC
-20°C~+50°C
Horizontally or vertically installed
74*167*58.4 (mm)
H2 Photocells
Detection type
Operating distance
Response time
Input voltage
Operating Temperature
Protection level
Dimension
Through beam
MAX~15 meters
<100mS
AC/DC 12-24V
-20°C~+50°C
IP54
63*63*30 (mm)
P1 Keypad
Frequency
Coding
Power Supply
Operating Temperature
Dimension
433.92Mhz
Rolling code
12 ~ 24V DC/AC
-20°C~+50°C
106*53*20 (mm)
RB1 Receiver Box
Frequency
Coding
Power Supply
Operating Temperature
Dimension
433.92Mhz
Rolling code
12 ~ 24V DC/AC
-20°C~+50°C
106*53*20 (mm)
K1 Key Selector
Operating Temperature
Dimension
-20°C~+50°C
73.2*73.2*42.3 (mm)

GARAGE DOOR OPENERS USER MANUAL 18

GARAGE DOOR OPENERS USER MANUAL
34100-196-05-B
19