Toa Q-2008SPD User manual

DIGITAL MIXING PROCESSOR UNIT
DESCRIPTION
Q-2008SPD
For details, refer to the instruction manual enclosed with the Q-2008SPD.
1
2
3
47
10 11 12 13
19
20
14
15
16
17
18
5
8
6
9
21
22
23
24
25
［Front］
The Q-2008SPD Digital Mixing Processor Unit is designed to have up to 32 audio inputs and outputs in total.A
built-in multiple signal processing functions permit the unit to be used as both a mixer and a signal
processor.Each function can be set using the Q-2008SPD Setting Software.
Operation can be performed through the front key operation and from a PC with the Q-2008SPD Setting
Software installed.
SIMPLE INSTRUCTION MANUAL
NOMENCLATURE AND FUNCTIONS

Note: Dante is a trademark of Audinate Pty Ltd.
133-02-00200-00
1. Power switch [POWER ON/OFF]
Power is switched on and off with each depression of
this switch.
2. Power lamp
Lights when the power switch is set to ON.
3. Level indicators [PEAK, +12 dB, 0 dB, – 40 dB]
Indicate the signal level of each individual channel.
Indicate the PFL (pre-fader level) value for the input
channel, and the AFL (after-fader level) value for the
output channel.
4. Gate indicator (Orange)
Lights when the gate is activated.
5. Monitor selection indicator (Orange)
Lights to indicate the corresponding channel is selected
for monitoring using headphones.
6. Key lock indicator (Red)
Lights when key lock function is enabled.
7. Item selection indicators
[PRESET, UNIT ID, MONITOR, CONSOLE, Dante] (Green)
The indicator of the item selected with the Selection keys
lights.
8. Number display
Displays the number of the preset memory recalled.
9. Reset switch
Restarts the Q-2008SPD when pressed.
Press the switch (recessed) with a pen tip.
Note
Reactivating the unit stops audio signals currently being
output.
10. USB terminal
Not used.
11. Headphone jack
Audio outputs for the channel of which Monitor
selection indicator (5) is lighting can be monitored.
Connect stereo headphones of 16 Ω or more. Adjust
the monitor volume with the headphone volume
control knob (12).
12. Headphone volume control knob
Adjusts the headphone volume.
13. Selection keys
Use the Up and Down keys to select the Item selection
indicator.
Use the Left and Right keys to select the preset
memory number when recalling the preset memory.
14. Set key
Used for preset memory recall or key lock setting.
15. LAN LINK/ACT indicator (Green)
Lights when the LAN connector on the rear panel is
connected, and flashes during LAN communications.
16. LAN DETECT indicator (Orange)
Not available.
17. SYSTEM STATUS indicator (Green)
Lights when the unit is in communication with a PC.
18. SYSTEM ERROR indicator (Red)
Lights while the unit is being activated, and goes out
after the activation has been completed.
If this indicator remains lit even after activation
completion, this indicates an internal fan failure.
19. SYSTEM RUN indicator (Green)
Lights when the unit is in normal operation, and goes
out when a failure occurs.
20. Dante PRIMARY LINK indicator (Green)
Flashes during Dante communications via the primary
port.
21. Dante SECONDARY LINK indicator (Green)
Flashes during Dante communications via the
secondary port.
22. Dante MASTER indicator (Green)
Lights when Dante is in operation as the MASTER.
23. Dante CLOCK SYNC indicator (Green)
Lights when internal word clock synchronization is
stable. Goes out if the clock gets out of synchronization,
then the internal mute functions,causing the audio
outputs to be interrupted.
24. Dante ACTIVE indicator (Green)
Lights when the built-in Dante module is working
normally.
25. Dante IDENTIFY indicator (Green)
Flashes when the Identify button is clicked on the
Dante Controller.
Note
The WORD CLOCK terminals on the rear panel are not
used. Do not connect anything and shift the 75 Ω switch to
the "OFF" position.
(Factory preset : OFF)