Toolots W1.2×450 User manual


V1.0





HANDBRAKEMETALBENDER
OPERATIONMANUAL

W1.2×450
W1.2×630
W1.0×1000




V1.0
1

WARNING
Readandunderstandallinstructionsbeforeusingthistool.
Theoperatormustfollowbasicprecautionstoreducethe
riskofpersonalinjuryand/ordamagetotheequipment.

HAZARDDEFINITIONS
Pleasefamiliarizeyourselfwiththehazardnoticesfoundin
thismanual.Anoticeisanalertthatthereisapossibilityof
propertydamage,injuryorlossoflifeifcertaininstructions
arenotfollowed.
DANGER! Thisnoticeindicatesanimmediateandspecific
hazardthatwillresultinseverepersonalinjuryor
lossoflifeiftheproperprecautionsarenottaken.
WARNING!Thisnoticeindicatesaspecifichazardorunsafe
practicethatcouldresultinseverepersonalinjuryor
lossoflifeiftheproperprecautionsarenottaken.
CAUTION!Thisnoticeindicatesapotentiallyhazardoussituation
thatmayresultinminorormoderateinjuryifproper
practicesarenottaken.
NOTICE!Thisnoticeindicatesthataspecifichazardorunsafe
practicewillresultinequipmentorpropertydamage,
butnotpersonalinjury.

V1.0
2
WORKAREA
1. Operateinasafeworkenvironment,Keepyourworkareaclean,
well‐litandfreeofdistractions.Placelightssoyouarenot
workinginashadow.
2. Keepanyonenotwearingtheappropriatesafetyequipment
awayfromtheworkarea.
3. Storeunusedtoolsproperlyinasafeanddrylocationtoprevent
rustordamage.Locktoolsawayandkeepoutofthereachof
children.
Usage
1. Thismachineissuitableforbendsheetmetalupto18gauge,and20
gaugethickness,thebrakeportionofthemachineisdesignedtocreate
bendsupto135°.
2. Maintechnicalspecification
ModelW1.2×450W1.2×630W1.0×1000
Max.Working
Length
17‐23/32"24‐13/16"39‐3/8"
450mm630mm1000mm
Max.SheetMetal
Thickness
18Gauge18Gauge20Gauge
1.2mm1.2mm1mm
Foldingangle0‐135°0‐135°0‐135°
PackingSize
(L×W×H)
21‐21/32"×7‐3/32"×5‐1/2"28‐11/32"×7‐3/32"×6‐5/16" 43‐11/16"×9‐7/16"×7‐7/8"
550×180×140mm720×180×160mm1110×240×200mm
Weight
23.2lbs.38.6lbs.77.2lbs.
10.5kg17.5kg35kg

V1.0
3

3.Installationandcaution
3.1Installation
3.1.1Pleasecheckwhetherthepartofthismachinearefullyequipped
andnotdamagedaccordingtothepartslistorpartfigure.
3.1.2Thismachineshouldbemountedonworkbenchorspecific
stand(notsupplied)
3.1.3Pleaseleaveplentyroomaroundthemachineforyoureasy
operating,inordertoavoidinjury.
3.1.4Pleaseremovetheanti‐rustgreaseonprocessingsurfacesand
somepartsincludedkerosene.
3.2Caution
3.2.1Pleasereadthemanualbeforeoperationandmakeyourself
understanditsstructureandprinciplecompletely.
3.2.2Pleasedon'toperatethematerialwidthandthicknessthantablelist
max.Range.
3.2.3Alwayswearindustrialstandardapprovedeyeprotection,using
safetyequipmentsuchasdustmask,non‐skidsafetyshoes,ahelmet
andhearingprotectionwillreducethechancesofseriousinjuries.
3.2.4Donotexposethedevicetotherainorwetconditions.
3.2.5Dressappropriatelydonotwearlooseclothingorjewelry.Keepyour
hair,clothingandglovesawayfromthemovingpartstoavoidgetting

V1.0
4

caughtinthemovingparts.Failuretopayattentioncouldcause
seriousinjuryorevendeath.


4.Operation
4.1Markthedesiredlocationofyourbendontheworkpiece.
4.2Positiontheworkpiecesothemarkisalignedwiththebackedgeofthe
supportplate.
4.3Withsteadyevenmovementandpressure,liftthehandlestogetherto
bendtheworkpiecetothedesiredangle.

5.Maintenance
Lubricatetherotatingpartsofthemachine.


6.Partslist
ALowerbeamBHandle
CFoldingbeamDTommyscrew
EUpperbeamFScrew
GSpringHFlap




V1.0
5

7.Assemblydiagram