Topica TP-2006 AX User manual

TP-2006 AX

General
New color CCD camera TP-2006 AX "Black
Knight" uses high sensitive 1/3" interline
transfer CCD (Charge Couple Device). Its
attractive black finish and stramlined round
body, as well as B.L.C., Level adjustment,
E.S, and other functions are the reasons for
its competence in CCTV field. TP-2006AX is
suitable to industrial and consumer use.
.
1

Features
(1)Back Light Compensation(B.L.C.)
Normal function is for the regular circum-
stance. B.L.C. function is for the better back
light treatment for objects under bright-light
area.
(2)Level adjustment
When switch to Direct Drive, use level
adjustment to take a clearer picture in
bright and dark areas.
(3)AES on/off switch
To select manual lens or auto iris lens
under different circumstance. Selection of
manual iris lens will save the cost of lens
and even keep the similar functions like
auto iris lens.
2

Precautions
(1)To protect camera, do not expose the
device to humidity and dust.
(2)Handle the camera with care
This camera consists of sensitive
highprecision parts. Do not place it in a
location subject to vibration or on an
unstable base.
(3)CCD sensor consists of sensitive highpre-
cision. Do not touch it by hand directly.
(4)When the device is not in use, please put
the lens mount cap on the lens.
(5)Please avoid to install the camera directly
toward the strong light source, such as sun,
spotlight...etc.
3

Precautions
Compositions
Camera...........................................................1
Iens mount cap...............................................1
L-shape wrench..............................................1
Instruction manual..........................................1
C Mount 5mm Adaptor ring............................1
Warranty Card................................................1
(6)Projection of the lens or other piece of
optical equipment must be less than 6mm
from the lens mount face.
(7)In case the camera with any defect,
please inform the qualified service person.
Don't try to disassemble the camera by
yourself.
4

Function of parts and wiring
(1)Lens mount
Use CS mount lens or C mount lens with
the attached 5mm adaptor ring.
(2)Video signal output connector (BNC
connector)
Connect to CCTV monitor by using a
coaxial cable.
(3)Auto iris connector
Connect the cable from auto iris lens to the
pin no. 1 to 4 on camera according to the
following Instruction.
5
D.D.
1. Control -
2. Control +
3. Drive +
4. Drive -

Connections
6
(1) Single Connection (one camera to one
CCTV monitor)
(2) Multiple Connection (plural cameras to one
CCTV monitor)

Operation & adjustment
7
(1)Install lens to the camera.
(2)Connect a cable between camera and
CCTV monitor and then turn on the power of
each device.
(3)To obtain the best picture, adjust the focus
and the diaphragrm while observing the
image plane.
(4)Back focus adjustment
If the subject is not in focus after adjusted
the focus of lens, it's need to make the back
focus adjustment. First, set the focus ring of
lens to the widest position and take picture of
the subject at a distance of 20m away from
camera.
Second, loosen the screw at the front panel
by L-shape wrench. Then, turn the lens and
mount at the same time. So the subject will
be in focus. Finally, secure the screw firmly.

Specifications
PICK UP DEVICE
PICTURE ELEMENTS
SYNC SYSTEM
HORIZONTAL RESOLUTION
WHITE BALANCE
DIMENSIONS
WEIGHT
LENS MOUNT
B.L.C.
AUTO GAIN CON CONTROL
GAMMA CORRECTION
ELECTRONIC SHUTTER
IRIS CONTROL
POWER SOURCE
S/N RATIO
VIDEO OUTPUT
MINIMUM ILLUMINATION
POWER CONSUMPTION
WORKING TEMPERATURE
1/3" Interline Transfer CCD
NTSC: 510(H) x 492(V)
PAL: 500(H) x 582(V)
Internal sync
58
400 TV lines
CS mount or C mount
with 5mm adaptor ring
Auto
ON/OFF Switch
Auto
0.45
1/60(1/50) to 1/100,000 (1/100.000)Sec.
on/off switch
Direct Drive only
DC 12V / AC 24V or DC12V
Over 48 dB
1.0Vp-p, 75ohm
0.4 Lux / F1.4
Approx. 3.0W
-10 to +45
(W) x 50(H) x 95(D) mm
Approx. 192g
8

Dimensions & parts location
VIDEO VIDEO
1. AES
2. BLC
1. AES
2. BLC
DC12V
+
-
1 2 1 2
LEVEL LEVEL
AC24V/DC12V
58 mm
95 mm
50 mm
DC 12V AC 24V/DC 12V
9
1. Control -
2. Control +
3. Drive +
4. Drive -
1. Control -
2. Control +
3. Drive +
4. Drive -