Tornado 2440 ANNEX A User manual

Tornado 2440 Annex A
Tornado 2441 Annex B
ADSL 2/2+ Wireless LAN Modem/Router
User Manual

GENERAL INFORMATION
The 4-Port Wireless Ethernet Router features 4 LAN ports and a wireless
ability.
Included in the package are the following.
• 1 4-Port Wireless Ethernet Router
• 1 AC Power Adapter
• 1 RJ-11 Cable
• 1 RJ-45 Cable
• 1 User Manual on cd
Front Panel View
- 1 -

The front panel of the router has LED indicators, described below.
LED MODE INDICATION
Solid Wireless is enabled.
No light Wireless is disabled.
AP
Blinking There is wireless traffic.
Solid ADSL is connected.
No light ADSL is not connected. The ALARM led will
be red.
XDSL
Link
Blinking The router is connected to ADSL.
Solid ADSL is connected, and there is no ADSL
traffic.
No light ADSL is not connected.
XDSL
ACT
Quick blinking There is ADSL traffic.
Solid Router is connected to the LAN.
No light No connection to the LAN. Check if the LAN
cable is connected to the router.
LAN1-
LAN4
Blinking LAN traffic
Solid (red) ADSL is not connected.
ALARM No light ADSL is connected.
Solid Router is powered on.
POWER No light Router is not powered. Check if the router is
plugged in and if the power switch is turned on.
- 2 -

Back Panel View
Port Description
Power Switch Press to turn the router on and off.
Power Connects to a 15VDC AC power adapter.
Reset
Restart —press the button for less than 4
seconds.
Default settings —press the button for 4
seconds or longer.
LAN1-LAN4 RJ-45 connects the unit to an Ethernet
device such as a PC or a switch.
Console
NOTE: To be used for maintenance
professionals only. If the router needs
repair, bring it to a service professional.
Line RJ-11 cable connects to the splitter
provided.
- 3 -

INSTALLING THE ROUTER
Connect the ADSL Line and Telephone
An RJ-11 cable will be connected to the wall phone jack and the line-end of
the splitter. Connect another RJ-11 phone wire from the modem-end of the
splitter to the port labeled “line” on the router. A third RJ-11 phone wire will be
needed to connect the telephone to the phone-end of the splitter.
NOTE: See connections on the installation d agram.i
Connect the PC to the Router
• Use the Ethernet cable to connect your computer directly to the router.
Connect one end of the Ethernet cable to one of the ports labeled LAN
on the rear panel of the router and connect the other end to the
Ethernet port of your computer. Attach any additional PCs to the
router using RJ-45 cables to the port labeled LAN on the rear panel of
the router.
Connect the Power Adapter
Complete the process by connecting the AC power adapter to the POWER
connector on the back of the device and plug the adapter into a wall outlet or
power strip. Then turn on and boot up your PC and any LAN devices, such
as hubs or switches, and any computers connected to them.
- 4 -

Installation Diagram
- 5 -

Configuring Your Computer
Prior to accessing the router through the LAN port, note the following
necessary configurations.
• Your PC’s TCP/IP address: 192.168.1.__( the last number is any
number between 3 and 254)
• The router’s default IP address: 192.168.1.1
• Subnet mask: 255.255.255.0
The below table displays the procedures for configuring your PC as organized
by the different operating systems.
- 6 -
OPERATING SYSTEM
PROCEDURES
1. In the Windows task bar, click on the Start button, and
then click on Control Panel.
2. Double-click on the Network Connections icon.
3. In the LAN or High-Speed Internet window, right-click on
the icon corresponding to your LAN connection, and
select Properties.
4. Make sure that the check box to the left of the item
labeled Internet Protocol (TCP/IP) is checked, and click
on the Properties button.
5. In the Internet Protocol (TCP/IP) Properties dialog box,
click on the radio button labeled Use the following IP
address. Type an address between 192.168.1.3 and
192.168.1.254 in the IP Address field and 255.255.255.0
in the Subnet Mask field.
Windows
XP
6. Click on the OK button twice to confirm your changes, and
close the Control Panel.
1. In the Windows task bar, click on the Start button, point to
Settings, and click on Control Panel.
2. Double-click on the Network and Dial-up Connections
icon.
3. In the Network and Dial-up Connections window, right-
click on the Local Area Connection icon and then select
Properties. The Local Area Connection Properties dialog
box displays a list of currently installed network
components. If the list includes Internet Protocol
(TCP/IP), the protocol has already been enabled.
Proceed to step 10.
4. If Internet Protocol (TCP/IP) does not appear as an
installed component, then click on the Install button.
Windows
2000
5. In the Select Network Component Type dialog box, select
Protocol and then click on the Add button.

6. Select Internet Protocol (TCP/IP) in the Network Protocols
list, and click on the OK button. When prompted to install
files from your Windows 2000 installation CD or other
source, follow the instructions for installation.
7. Restart your computer if prompted to do so in order for
the changes to take effect.
8. After restarting, click on the Network and Dial-up
Connections icon in the Control Panel.
9. In the Network and Dial-up Connections window, right
click on the Local Area Connection icon, and select
Properties.
10. In the Local Area Connections Properties dialog box,
select Internet Protocols (TCP/IP) and then click on the
Properties button.
11. In the Internet Protocols (TCP/IP) Properties dialog box,
click on the radio button labeled Use the following IP
address. Enter an IP address 192.168.1.3 and
192.168.1.254 in the IP address field and in the Subnet
Address field enter 255.255.255.0.
- 7 -
12. Click on the OK button twice to save the changes and
close the Control Panel.
1. In the Windows task bar, click on the Start button, point to
Settings, and click on Control Panel.
2. Double-click on the Network and Dial-up Connections
icon.
3. In the Network and Dial-up Connections window, right-
click on the Local Area Connection icon and then select
Properties. The Local Area Connection Properties dialog
box displays a list of currently installed network
components. If the list includes Internet Protocol
(TCP/IP), the protocol has already been enabled.
Proceed to step 11.
4. If Internet Protocol (TCP/IP) does not appear as an
installed component, then click on the Install button.
5. In the Select Network Component Type dialog box, select
Protocol and then click on the Add button.
6. Select Microsoft from the Manufacturers list box.
7. Select Internet Protocol (TCP/IP) in the Network Protocols
list, and click on the OK button. When prompted to install
files from your Windows 2000 installation CD or other
source, follow the instructions for installation.
8. Restart your computer if prompted to do so in order for
the changes to take effect.
9. After restarting, click on the Network and Dial-up
Connections icon in the Control Panel.
10. In Network and Dial-up Connections window, right-click
on the Network icon and then select Properties.
11. In the Network Properties dialog box, select TCP/IP, and
then click on the Properties button.
Windows
ME
12. In the Internet Protocols (TCP/IP) Properties dialog box,
click on the radio button labeled Use the following IP
address. Enter an IP address 192.168.1.3 and
192.168.1.254 in the IP address field and in the Subnet
Address field enter 255.255.255.0.

- 8 -
13. Click on the OK button twice to save the changes and
close the Control Panel.
1. In the Windows task bar, click on the Start button, point to
Settings, and click on Control Panel.
2. Double-click on the Network icon. The Network dialog
box displays a list of currently installed network
components. If the list includes TCP/IP, the protocol has
already been enabled. Skip to step 9.
3. If TCP/IP does not appear as an installed section, click on
the Add button. The Select Network Component Type
dialog box appears.
4. Select Protocol, and click on the Add button. The Select
Network Protocol dialog box appears.
5. Select Microsoft from the Manufacturers list box and click
on TCP/IP in the Network Protocols list box.
6. Click on the OK button to return to the Network dialog box
and then click on the OK button again. You may be
prompted to use your Windows 95/98 installation CD to
install files. Follow those installation instructions.
7. Click on the OK button to restart the PC and then
complete the installation of TCP/IP.
8. After restarting your computer, open the Control Panel
window and click on the Network icon.
9. Select the network component labeled TCP/IP, and then
click on the Properties button. If you have multiple
TCP/IP listings, select the listing associated with your
network card or adapter.
10. In the TCP/IP Properties dialog box, click on the IP
Address tab.
11. Click on the radio button labeled Use the following IP
address. Enter an IP address 192.168.1.3 and
192.168.1.254 in the IP address field and in the Subnet
Address field enter 255.255.255.0.
Windows
95, 98
12. Click on the OK button twice to save the changes. You
will be prompted to restart your computer. Click on the
Yes button to restart your PC.
1. In the Windows task bar, click on the Start button, point to
Settings, and click on Control Panel.
2. In the Control Panel window, double-click on the Network
icon.
3. In the Network dialog box, click on the Protocols tab. The
Protocols tab displays a list of currently installed network
protocols. If the list includes TCP/IP, the protocol has
already been enabled. Skip to step 9.
4. If TCP/IP does not appear as an installed section, click on
the Add button.
Windows
NT 4.0
5. You may be prompted to use your Windows NT
installation CD to install files. Follow those installation
instructions. After all files are installed, a window appears
stating that a TCP/IP service called DHCP can be set up
to dynamically assign IP addresses.

6. Click on the Yes button to continue and then click on OK if
prompted to restart your computer.
7. After restarting your PC, open the Control Panel window
and then double-click on the Network icon.
8. In the Network dialog box, click on the Protocols tab.
9. In the Protocols tab, select TCP/IP and then click on
Properties.
10. In the Microsoft TCP/IP Properties dialog box, click on the
radio button labeled Use the following IP address. Enter
an IP address 192.168.1.3 and 192.168.1.254 in the IP
address field and in the Subnet Address field enter
255.255.255.0.
11. Click on the OK button twice to save the changes and
close the Control Panel.
- 9 -

Logging in to the Router
This section explains how to log in to your router using the following steps.
1. Launch your web browser.
2. Enter the URL http://192.168.1.1 in the address bar and click on
Enter.
A login screen like the one below will be displayed after you connect to the
user interface.
3. Enter your user name and password, and then click on OK to
display the user interface.
NOTE: There are two default user name and password combinat ons.
The user / user name and password combination can display device status,
but cannot change or save configurations. The admin / admin combination
can perform all functions. Passwords can be changed at any time.
i
- 10 -

Device Info
This section describes the system information that can be accessed using the
menu items under Device Info.
Summary
Access the general status report from the router by clicking on
“Summary” under “Device Info”. It shows information about the router
such as the version of the software, bootloader, etc. It also displays
the current status of your DSL connection as shown below.
- 11 -

WAN
Access the WAN status report from the router by clicking on “WAN” under
“Device Info”
STATISTICS
LAN Statistics
Access the LAN statistics from the router by clicking on the “LAN” item under
“Statistics”
- 12 -

WAN Statistics
Access the WAN statistics from the router by clicking on the “WAN” item
under “Statistics”
ATM Statistics
Access ATM statistics from the router by clicking on the “ATM” item under
“Statistics”
- 13 -

ADSL Statistics
You can view ADSL statistics by clicking on the “ADSL” item under
“Statistics”. Information contained in this screen is useful for
troubleshooting and diagnostics of connection problems.
- 14 -

ADSL BER Test
A Bit Error Rate Test (BER Test) is a test that reflects the ratio of error bits to
the total number transmitted.
If you click on the ADSL BER Test button at the bottom of the ADSL Statistics
page, the following pop-up screen will appear allowing you to set the tested
time and to begin the test.
Below is an ADSL BER Test result screen displaying information about the
test and the error bits and ratio.
- 15 -

Route
Access the routing status report from the router by clicking on the “Route”
item under “Device Info”.
- 16 -

ARP
Access the ARP status report from the router by clicking on the “ARP” item
under “Device Info”
- 17 -

QUICK SETUP
This section will explain how to configure the router.
ATM PVC Configuration
To enable the auto-connect process, click on the box labeled DSL Auto-
connect, a process that will automatically detect the first usable PVC and
automatically detect PPPoE, PPPoA, and Bridge Protocol (with DHCP Server
available). To continue, click on the Next button.
If you do not use DSL Auto-connect, then you may need to change the VPI
and VCI numbers. Quality of service can also be enabled on this screen.
Furthermore, if you do not use DSL Auto-connect, then you will need to select
the connection type and encapsulation mode from a list as shown below.
- 18 -

The next screen to appear will depend on the connection type that was
selected in the previous screen. The following screen is a result of choosing
IP over ATM (IPoA) as the connection type.
- 19 -