Toshiba Satellite 5000 Series User manual

TOSHIBA 5000 Series
Portable Personal Computer
User’s Manual

Copyright
©2001byTOSHIBACorporation.Allrightsreserved.Underthecopyrightlaws,
this manual cannot be reproduced in any form without the prior written permission
of TOSHIBA. No patent liability is assumed, with respect to the use of the informa-
tion contained herein.
TOSHIBA 5000 Series Portable Personal Computer User’s Manual
First edition August 2001
Disclaimer
This manual has been validated and reviewed for accuracy. The instructions and
descriptions it contains are accurate for the TOSHIBA 5000 Series Portable Personal
Computer at the time of this manual’s production. However, succeeding computers
and manuals are subject to change without notice. TOSHIBA assumes no liability
for damages incurred directly or indirectly from errors, omissions or discrepancies
between the computer and the manual.
Trademarks
IBMPC, OS/2 and PS/2 aretrademarks of International Business MachinesCorpo-
ration.
Inteland Pentium are registered trademarks of Intel Corporation.
Windows and Microsoft are registered trademarks of Microsoft Corporation.
Centronicsis a registered trademark of Centronics Data Computer Corporation.
PhotoCDisatrademark ofEastmanKodak.
i.LINKisatrademark.
Bluetooth is a trademark owned by its proprietor and used by TOSHIBA under
license.
Other trademarks and registered trademarks not listed above may be used in this
manual.

COMPLIES WITH FDA RADIATION
PERFORMANCE STANDARDS, 21
CFR SUBCHAPTER J. 130KMT
Manufactured by Kyushu Matsushita
Electric Co., Ltd. 1-62, 4-Chome
Minoshima Hakata-Ku Fukuoka,
Japan
CLASS 1 LASER PRODUCT
LASER KLASSE 1
Matsushita CD-RW/DVD-ROM drive
UJDA710 safety instruction
CAUTIONS: 1. TheCD-RW/DVD-ROMdrive employsalasersystem.To
ensure proper use of this product, please read this
instruction manual carefully and retain for future
reference. Should the unit ever require maintenance,
contact an authorized service location.
2. Use of controls, adjustments or the performance of
procedures other than those specified may result in
hazardous radiation exposure.
3. To prevent direct exposure to the laser beam, do not try
to open the enclosure.
Location of the required label

CAUTION: This appliance contains a laser
system and is classified as a “CLASS 1 LASER
PRODUCT.” To use this model properly, read
the instruction manual carefully and keep this
manual for your future reference. In case of any
trouble with this model, please contact your
nearest“AUTHORIZEDservicestation.”To
prevent direct exposure to the laser beam, do not
try to open the enclosure.
VORSICHT: Dieses Gerät enthält ein Laser-
System und ist als “LASERSCHUTZKLASSE 1
PRODUKT” klassifiziert. Für den richtigen
Gebrauch dieses Modells lesen Sie bitte die
Bedienungsanleitung sorgfältig durch und
bewahren diese bitte als Referenz auf. Falls
Probleme mit diesem Modell auftreten,
benachrichtigen Sie bitte die nächste
“autorisierte Service-Vertretung”. Um einen
direkten Kontakt mit dem Laserstrahl zu
vermeiden darf das Gerät nicht geöffnet
werden.
ADVARSEL: Denne mærking er anbragt
udvendigt på apparatet og indikerer, at
apparatet arbejder med laserstråler af klasse 1,
hviket betyder, at der anvendes laserstrlier af
svageste klasse, og at man ikke på apparatets
yderside kan bilve udsat for utilladellg kraftig
stråling.
APPARATETBORKUNÅBNESAFFAGFOLK
MEDSÆRLIGTKENDSKABTILAPPARATER
MEDLASERSTRÅLER!
Indvendigt i apparatet er anbragt den her
gengivne advarselsmækning, som advarer imod
at foretage sådanne indgreb i apparatet, at man
kan komme til at udsætte sig for laserstråling.
OBS! Apparaten innehåller laserkomponent
som avger laserstråining överstigande gränsen
för laserklass 1.
CLASS 1 LASER PRODUCT
APPAREIL ÅLASER DE
CLASSE 1
LASER KLASSE 1 PRODUKT
TOEN60825-1
ADVERSEL: USYNLIG
LASERSTRÅLING VED ÅBNING,
NÅR SIKKERHEDSAF-BRYDER
ER UDE AF FUNKTION.
UNDGÅUDSÆTTELSE FOR
STRÅLING

VAROITUS. Suojakoteloa si saa avata. Laite
sisältää laserdiodin, joka lähetää
näkymätöntä silmilie vaarallista
lasersäteilyä.
CAUTION:USEOFCONTROLSORADJUST-
MENTSORPERFORMANCEOFPROCE-
DURESOTHERTHANTHOSESPECIFIEDIN
THEOWNER’SMANUALMAYRESULTIN
HAZARDOUSRADIATIONEXPOSURE.
VORSICHT:DIEVERWENDUNGVON
ANDERENSTEURUNGENODER
EINSTELLUNGENODERDAS
DURCHFÜHRENVONANDEREN
VORGÄNGENALSINDER
BEDIENUNGSANLEITUNGBESCHRIEBEN
KÖNNENGEFÄHRLICHE
STRAHLENEXPOSITIONENZURFOLGE
HABEN.

PRODUCT IS CERTIFIED BYTHE
MANUFACTURER TO COMPLY
WITH DHHS RULES 21 CFR
SUBCHAPTER J APPLICABLE AT
THE DATE OF MANUFACTURE.
MANUFACTURED:
TOSHIBA CORPORATION
1-1, SHIBAURA 1-CHOME
MINATO-KU, TOKYO 105-8001,
JAPAN
TOSHIBA DVD-ROM drive SD-C2502
safety instruction
CAUTIONS: 1. The DVD-ROM drive employs a laser system. To ensure
proper use of this product, please read this instruction
manual carefully and retain for future reference. Should
the unit ever require maintenance, contact an authorized
service location.
2. Use of controls, adjustments or the performance of
procedures other than those specified may result in
hazardous radiation exposure.
3. To prevent direct exposure to the laser beam, do not try to
open the enclosure.
Location of the required label

CAUTION: This appliance contains a laser
system and is classified as a “CLASS 1 LASER
PRODUCT.” To use this model properly, read
the instruction manual carefully and keep this
manual for your future reference. In case of any
trouble with this model, please contact your
nearest“AUTHORIZEDservicestation.”To
prevent direct exposure to the laser beam, do
not try to open the enclosure.
VORSICHT: Dieses Gerät enthält ein Laser-
System und ist als “LASERSCHUTZKLASSE 1
PRODUKT” klassifiziert. Für den richtigen
Gebrauch dieses Modells lesen Sie bitte die
Bedienungsanleitung sorgfältig durch und
bewahren diese bitte als Referenz auf. Falls
Probleme mit diesem Modell auftreten,
benachrichtigen Sie bitte die nächste
“autorisierte Service-Vertretung”. Um einen
direkten Kontakt mit dem Laserstrahl zu
vermeiden darf das Gerät nicht geöffnet
werden.
ADVARSEL: Denne mærking er anbragt
udvendigt på apparatet og indikerer, at
apparatet arbejder med laserstråler af klasse 1,
hviket betyder, at der anvendes laserstrlier af
svageste klasse, og at man ikke på apparatets
yderside kan bilve udsat for utilladellg kraftig
stråling.
APPARATETBORKUNÅBNESAFFAGFOLK
MEDSÆRLIGTKENDSKABTILAPPARATER
MEDLASERSTRÅLER!
Indvendigt i apparatet er anbragt den her
gengivne advarselsmækning, som advarer imod
at foretage sådanne indgreb i apparatet, at man
kan komme til at udsætte sig for laserstråling.
OBS! Apparaten innehåller laserkomponent
som avger laserstråining överstigande gränsen
för laserklass 1.
CLASS 1 LASER PRODUCT
APPAREIL ÅLASER DE
CLASSE 1
LASER KLASSE 1 PRODUKT
TOEN60825-1
ADVERSEL: USYNLIG
LASERSTRÅLING VED ÅBNING,
NÅR SIKKERHEDSAF-BRYDER
ER UDE AF FUNKTION.
UNDGÅUDSÆTTELSE FOR
STRÅLING

VAROITUS. Suojakoteloa si saa avata. Laite
sisältää laserdiodin, joka lähetää
näkymätöntä silmilie vaarallista
lasersäteilyä.
CAUTION:USEOFCONTROLSORAD-
JUSTMENTSORPERFORMANCEOF
PROCEDURESOTHERTHANTHOSE
SPECIFIEDINTHEOWNER’SMANUAL
MAYRESULTINHAZARDOUSRADIATION
EXPOSURE.
VORSICHT:DIEVERWENDUNGVON
ANDERENSTEURUNGENODER
EINSTELLUNGENODERDAS
DURCHFÜHRENVONANDEREN
VORGÄNGENALSINDER
BEDIENUNGSANLEITUNGBESCHRIEBEN
KÖNNENGEFÄHRLICHE
STRAHLENEXPOSITIONENZURFOLGE
HABEN.

Modem warning notice
Conformity Statement
The equipment has been approved to [Commission Decision “CTR21”] for pan-
European single terminal connection to the Public Switched Telephone Network
(PSTN).
However, due to differences between the individual PSTNs provided in different
countries/regions the approval does not, of itself, give an unconditional assurance
of successful operation on every PSTN network termination point.
In the event of problems, you should contact your equipment supplier in the first
instance.
Network Compatibility Statement
This product is designed to work with, and is compatible with the following
networks. It has been tested to and found to conform with the additional require-
mentsconditionalinEG201121.
Germany ATAABAN005,AN006,AN007,AN009,AN010and
DE03,04,05,08,09,12,14,17
Greece ATAABAN005,AN006andGR01,02,03,04
Portugal ATAABAN001,005,006,007,011andP03,04,08,10
Spain ATAABAN005,007,012,andES01
Switzerland ATAABAN002
All other countries/regions ATAABAN003,004
Specific switch settings or software setup are required for each network, please refer
to the relevant sections of the user guide for more details.
The hookflash (timed break register recall) function is subject to separate national
type approvals. It has not been tested for conformity to national type regulations,
and no guarantee of successful operation of that specific function on specific
national networks can be given.

Japan regulations
Region selection
If you are using the computer in Japan, technical regulations described in the
Telecommunications Business Law require that you select the Japan Region mode.
It is illegal to use the modem in Japan with any other selection.
Redial
Up to two redial attempts can be made. If more than two redial attempts are made,
the modem will return Black Listed. If you areexperiencing problems with the
Black Listed code, set the interval between redials at one minute or longer.
Japan’s Telecommunications Business Law permits up to two redials on analogue
telephones, but the redials must be made within a total of three minutes.
The internal modem is approved by Japan Approvals Institute for Telecommunications
Equipment.
A00-0940JP
Pursuant to FCC CFR 47, Part 68:
When you are ready to install or use the modem, call your local telephone company
andgivethemthefollowinginformation:
◆The telephone number of the line to which you will connect the modem
◆The registration number that is located on the device
TheFCCregistrationnumberof the modem will be found onyourmodem’slabel.
◆TheRingerEquivalenceNumber(REN)ofthemodem,whichcanvary.Forthe
RENofyourmodem,refertoyourmodem’slabel.
The modem connects to the telephone line by means of a standard jack called the
USOCRJ11C.
Type of service
Your modem is designed to be used on standard-device telephone lines. Connec-
tion to telephone company-provided coin service (central office implemented
systems) is prohibited. Connection to party lines service is subject to state tariffs. If
you have any questions about your telephone line, such as how many pieces of
equipment you can connect to it, the telephone company will provide this informa-
tion upon request.

Telephone company procedures
The goal of the telephone company is to provide you with the best service it can. In
order to do this, it may occasionally be necessary for them to make changes in their
equipment, operations, or procedures. If these changes might affect your service or
the operation of your equipment, the telephone company will give you notice in
writing to allow you to make any changes necessary to maintain uninterrupted
service.
If problems arise
If any of your telephone equipment is not operating properly, you should immedi-
ately remove it from your telephone line, as it may cause harm to the telephone
network. If the telephone company notes a problem, they may temporarily discon-
tinue service. When practical, they will notify you in advance of this disconnection.
If advance notice is not feasible, you will be notified as soon as possible. When
you are notified, you will be given the opportunity to correct the problem and
informed of your right to file a complaint with the FCC. In the event repairs are ever
needed on your modem, they should be performed by TOSHIBA Corporation or an
authorizedrepresentative ofTOSHIBACorporation.
Disconnection
If you should ever decide to permanently disconnect your modem from its present
line, please call the telephone company and let them know of this change.
Fax branding
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person
to use a computer or other electronic device to send any message via a telephone
fax machine unless such message clearly contains in a margin at the top or bottom
of each transmitted page or on the first page of the transmission, the date and time it
is sent and an identification of the business, other entity or individual sending the
message and the telephone number of the sending machine or such business, other
entityor individual. In order toprogram this information into yourfax modem, you
should complete the setup of your fax software before sending messages.

Instructions for IC CS-03 certified equipment
1The Industry Canada label identifies certified equipment. This certification means
that the equipment meets certain telecommunications network protective,
operational and safety requirements as prescribed in the appropriate Terminal
Equipment Technical Requirements document(s). The Department does not
guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The
equipment must also be installed using an acceptable method of connection.
The customer should be aware that compliance with the above conditions may
not prevent degradation of service in some situations. Repairs to certified
equipment should be coordinated by a representative designated by the
supplier. Any repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications company cause to
request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connec-
tions of the power utility, telephone lines and internal metallic water pipe system,
if present, are connected together. This precaution may be particularly important
inruralareas.
CAUTION: Users should not attempt to make such connections them-
selves, but should contact the appropriate electric inspection authority,
or electrician, as appropriate.
2The user manual of analog equipment must contain the equipment’s Ringer
EquivalenceNumber(REN)andanexplanationnoticesimilartothefollowing:
TheRingerEquivalenceNumber(REN)ofthemodem,whichcanvary.Forthe
RENofyourmodem,refertoyourmodem’slabel.
NOTICE: The Ringer Equivalence Number (REN) assigned to each
terminal device provides an indication of the maximum number of
terminals allowed to be connected to a telephone interface. The termina-
tion on an interface may consist of any combination of devices subject
only to the requirement that the sum of the Ringer Equivalence Numbers
of all the devices does not exceed 5.
3The standard connecting arrangement (telephone jack type) for this equipment is
jacktype(s):USOC RJ11C.
The IC registration number of the modem is shown below.
Canada:135311026A

Notes for Users in Australia and New Zealand
Modem warning notice for Australia
Modems connected to the Australian telecoms network must have a valid Austel
permit. This modem has been designed to specifically configure to ensure compli-
ance with Austel standards when the region selection is set to Australia. The use of
other region setting while the modem is attached to the Australian PSTN would
result in your modem being operated in a non-compliant manner. To verify that the
region is correctly set, enter the command ATI which displays the currently active
setting.
To set the region permanently to Australia, enter the following command sequence:
AT%TE=1
ATS133=1
AT&F
AT&W
AT%TE=0
ATZ
Failure to set the modem to the Australia region setting as shown above will result
in the modem being operated in a non-compliant manner. Consequently, there
would be no permit in force for this equipment and the Telecoms Act 1991 pre-
scribes a penalty of $12,000 for the connection of non-permitted equipment.
Notes for use of this device in New Zealand
◆The grant of a Telepermit for a device in no way indicates Telecom acceptance
of responsibility for the correct operation of that device under all operating
conditions. In particular the higher speeds at which this modem is capable of
operating depend on a specific network implementation which is only one of
many ways of delivering high quality voice telephony to customers. Failure to
operate should not be reported as a fault to Telecom.
◆In addition to satisfactory line conditions a modem can only work properly if:
a/ it is compatible with the modem at the other end of the call and
b/ the application using the modem is compatible with the application at the
other end of the call - e.g., accessing the Internet requires suitable
software in addition to a modem.
◆This equipment shall not be used in any manner which could constitute a
nuisance to other Telecom customers.

◆SomeparametersrequiredforcompliancewithTelecom’sPTCSpecifications
are dependent on the equipment (PC) associated with this modem. The
associated equipment shall be set to operate within the following limits for
compliancewithTelecomSpecifications:
a/ There shall be no more than 10 call attempts to the same number within
any30minuteperiod for any single manual call initiation, and
b/ The equipment shall go on-hook for a period of not less than 30 seconds
between the end of one attempt and the beginning of the next.
c/ Automatic calls to different numbers shall be not less than 5 seconds
apart.
◆Immediately disconnect this equipment should it become physically damaged,
and arrange for its disposal or repair.
◆The correct settings for use with this modem in New Zealand are as follows:
ATB0(CCITToperation)
AT&G2(1800Hzguardtone)
AT&P1(Decadicdialingmake-breakratio=33%/67%
ATS0=0 (not auto answer)
ATS6=2,3,4,5,6or7(Blinddialdelay,factorydefaultvalueof2isrecom-
mended)
ATS7=lessthan90(Timetowaittocarrierafterdialing)
ATS10=less than 150 (loss of carrier to hangup delay, factory default of 14
recommended)
ATS11=95(DTMFdialingon/offduration=95ms)
ATX2 (Dial tone detect, but not (U.S.A.) call progress detect)
◆When used in the Auto Answer mode, the SO register must be set with a value
between 2 and 10. This ensures:
(a) a person calling your modem will hear a short burst of ringing before the
modem answers. This confirms that the call has been successfully
switched through the network.
(b) caller identification information (which occurs between the first and
second ring cadences) is not destroyed.

◆The preferred method of dialing is to use DTMF tones (ATDT...) as this is
faster and more reliable than pulse (decadic) dialing. If for some reason you
must use decadic dialing, your communications program must be set up to
record numbers using the following translation table as this modem does not
implementthe NewZealand“ReverseDialing” standard.
Numbertobedialed:012345 6789
Numbertoprogramintocomputer:0987654321
Note that where DTMF dialing is used, the numbers should be entered
normally.
◆The transmit level from this device is set at a fixed level and because of this
there may be circumstances where the performance is less than optimal. Before
reporting such occurrences as faults, please check the line with a standard
Telepermitted telephone, and only report a fault if the phone performance is
impaired.
◆It is recommended that this equipment be disconnected from the Telecom line
duringelectricalstorms.
◆When relocating the equipment, always disconnect the Telecom line connec-
tion before the power connection, and reconnect the power first.
◆Thisequipmentmaynotbecompatible with Telecom Distinctive Alert ca-
dences and services such as FaxAbility.
NOTETHATFAULTCALLOUTSCAUSEDBYANYOFTHEABOVE
CAUSESMAYINCURACHARGEFROMTELECOM
General conditions
As required by PTC 100, please ensure that this office is advised of any changes to
the specifications of these products which might affect compliance with the relevant
PTCSpecifications.
The grant of this Telepermit is specific to the above products with the marketing
description as stated on the Telepermit label artwork. The Telepermit may not be
assigned to other parties or other products without Telecom approval.
A Telepermit artwork for each device is included from which you may prepare any
number of Telepermit labels subject to the general instructions on format, size and
color on the attached sheet.
The Telepermit label must be displayed on the product at all times as proof to
purchasers and service personnel that the product is able to be legitimately
connected to the Telecom network.

The Telepermit label may also be shown on the packaging of the product and in the
salesliterature,asrequiredinPTC100.
Thecharge foraTelepermitassessmentis $337.50.Anadditionalchargeof$337.50
is payable where an assessment is based on reports against non-Telecom New
Zealand Specifications. $112.50 is charged for each variation when submitted at the
sametime astheoriginal.
Aninvoicefor $NZ1237.50willbesent underseparatecover.
Information to Wireless LAN User
WirelessInteroperability
The TOSHIBA Wireless LAN Mini PCI Card products are designed to be
interoperable with any Wireless LAN product that is based on Direct Sequence
SpreadSpectrum(DSSS)radiotechnology, and is compliant to:
◆TheIEEE 802.11StandardonWireless LANs(RevisionB),as definedand
approved by the Institute of Electrical and Electronics Engineers.
◆The Wireless Fidelity (WiFi) certification as defined by the WECA Wireless
EthernetCompatibilityAlliance.
Wireless LAN and your Health
WirelessLAN products, like otherradio devices, emit radio frequency electromag-
netic energy. The level of energy emitted by Wireless LAN devices however is far
much less than the electromagnetic energy emitted by wireless devices like for
examplemobilephones.
Because Wireless LAN products operate within the guidelines found in radio
frequency safety standards and recommendations, TOSHIBA believes Wireless
LAN is safe for use by consumers. These standards and recommendations reflect
the consensus of the scientific community and result from deliberations of panels
and committees of scientists who continually review and interpret the extensive
researchliterature.
In some situations or environments, the use of Wireless LAN may be restricted by
the proprietor of the building or responsible representatives of the organization.
Thesesituationsmay for exampleinclude:
◆Using the Wireless LAN equipment on board of airplanes, or
◆In any other environment where the risk of interference to other devices or
services is perceived or identified as harmful.

If you are uncertain of the policy that applies on the use of wireless devices in a
specific organization or environment (e.g. airports), you are encouraged to ask for
authorization to use the Wireless LAN device prior to turning on the equipment.
Regulatory Information
The TOSHIBA Wireless LAN Mini PCI Card must be installed and used in strict
accordance with the manufacturer’s instructions as described in the user documen-
tation that comes with the product. This device complies with the following radio
frequency and safety standards.
Canada – Industry Canada (IC)
ThisdevicecomplieswithRSS210 of Industry Canada.
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of this device.”
L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il
ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit étre prét à
accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible
de compromettre le fonctionnement du dispositif.
Europe – EU Declaration of Conformity
Thisdevice complieswiththeessentialrequirementsofthe R&TTEDirective1999/
5/EC with essential test suites as per standards:
◆EN60950SafetyofInformationTechnologyequipment
◆ETS300328Technicalrequirementsforradioequipment
◆ETS300826GeneralEMCrequirementsforradioequipment.
België/ For outdoor usage only channel 10 (2457 MHz) and 11 (2462
Belgique: MHz) is allowed.
For private usage outside buildings across public grounds
over less than 300m no special registration with IBPT/BIPT is
required. Registration to IBPT/BIPT is required for private
usage outside buildings across public grounds over more
than 300m. An IBPT/BIPT license is required for public usage
outside building.
For registration and license please contact IBPT/BIPT.

Gebruik buiten gebouw alleen op kanalen 10 (2457 MHz) en
11 (2462 MHz). Voor privé-gebruik buiten gebouw over
publieke groud over afstand kleiner dan 300m geen registratie
bij BIPT/IBPT nodig; voor gebruik over afstand groter dan 300m
is wel registratie bij BIPT/IBPT nodig. Voor publiek gebruik
buiten gebouwen is licentie van BIPT/IBPT verplicht. Voor
registratie of licentie kunt u contact opnemen met BIPT.
L’utilisation en extérieur est autorisé sur le canal 10 (2457
MHz) et 11 (2462 MHz).
Dans le cas d’une utilisation privée, à l’extérieur d’un bâtiment,
au-dessus d’un espace public, aucun enregistrement n’est
nécessaire pour une distance de moins de 300m. Pour une
distance supérieure à 300m un enregistrement auprès de
I’IBPT est requise. Pour une utilisation publique à I’extérieur de
bâtiments, une licence de I’IBPT est requise. Pour les
enregistrements et licences, veuillez contacter I’IBPT.
Deutschland: License required for outdoor installations. Check with reseller
for procedure to follow
Anmeldung im Outdoor-Bereich notwendig, aber nicht
genehmigungspflichtig. Bitte mit Händler die Vorgehensweise
abstimmen.
France: Restricted frequency band: only channels 10 and 11 (2457
MHz and 2462 MHz respectively) may be used in France.
License required for every installation, indoor and outdoor
installations. Please contact ART for procedure to follow.
Bande de fréquence restreinte : seuls les canaux 10 à 11
(2457 et 2462 MHz respectivement) doivent être utilisés en
France.
Toute utilisation, qu’elle soit intérieure ou extérieure, est
soumise à autorisation. Vous pouvez contacter I’Autorité de
Régulation des Télécommuniations (http://www.art-telecom.fr)
pour la procédure à suivre.
Italia: License required for indoor use. Use with outdoor installations
not allowed
E’necessaria la concessione ministeriale anche per l’uso
interno.
Verificare con i rivenditori la procedura da seguire. L’uso per
installazione in esterni non e’ permessa.
Nederland License required for outdoor installations. Check with reseller
for procedure to follow

Licentie verplicht voor gebruik met buitenantennes. Neem
contact op met verkoper voor juiste procedure
USA-Federal Communications Commission(FCC)
Thisdevice complies with Part 15 of FCCRules. Operation of the devices in a
Wireless LAN System is subject to the following two conditions:
◆This device may not cause harmful interference.
◆This device must accept any interference that may cause undesired operation.
Caution: Exposure to Radio Frequency Radiation.
Theradiated output power of the TOSHIBA Wireless LAN MiniPCI Card is far
belowtheFCCradio frequencyexposurelimits.Nevertheless,theTOSHIBA
Wireless LAN Mini PCI Card shall be used in such a manner that the potential for
human contact during normal operation is minimized. When using this device in
combination with Wireless LAN Outdoor Antenna products, a certain separation
distance between antenna and nearby persons has to be kept to ensure RF expo-
sure compliance. The distance between the antennas and the user should not be
lessthan 5.0cm.
Refer to the Regulatory Statements as identified in the documentation that comes
with those products for additional information.
TheTOSHIBAWirelessLANMiniPCICardisfarbelow theFCCradiofrequency
exposurelimits.
Nevertheless, it is advised to use the TOSHIBA Wireless LAN Mini PCI Card in
such a manner that human contact during normal operation is minimized.
Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion.
This equipment generates, uses, and can radiate radio frequency energy. If not
installed and used in accordance with the instructions, it may cause harmful
interference to radio communications. However, there is no guarantee that interfer-
encewill not occur ina particular installation.

If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encour-
aged to try and correct the interference by one or more of the following measures:
◆Reorient or relocate the receiving antenna.
◆Increase the distance between the equipment and the receiver.
◆Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
◆Consult the dealer or an experienced radio/TV technician for help.
TOSHIBA is not responsible for any radio or television interference caused by
unauthorized modification of the devices included with this TOSHIBA Wireless
LAN Mini PCI Card, or the substitution or attachment of connecting cables and
equipment other than specified by TOSHIBA .
The correction of interference caused by such unauthorized modification, substitu-
tion or attachment will be the responsibility of the user.
Taiwan
Article14 Unlessapproved,foranymodelaccreditedlowpowerradiofrequency
electricmachinery,anycompany,traderorusershallnotchangethe
frequency,increasethepowerorchangethefeaturesandfunctions
of the original design.
Article17 Any use of low power radiofrequencyelectricmachineryshall not
affect the aviation safety and interfere with legal communications.
In event that any interference is found, the use of such electric
machinery shall be stopped immediately, and reusing of such
products can be resumed until no interference occurs after
improvement.
Thelegalcommunicationsmentionedintheaboveitemrefertoradio
communications operated in accordance with telecommunication
laws and regulations.
Low power radio frequency electric machinery shall resist against
interferencefromlegalcommunicationsorfromindustrial,scientific
andmedicalradioemissionelectricmachinery.
Using this equipment in Japan
InJapan,thefrequency bandwidth of 2,400~2,483.5MHz forsecondgenerationlow-
power data communication systems such as this equipment overlaps that of mobile
object identification systems (premises radio station and specified low-power radio
station).