Toshiba Satellite Pro 435CDS User manual

Satellite Pro™ 430 Series
Satellite Pro™ 435CDS
Reconfiguration Guide

Satellite Pro™ 430 Series
Satell~e Pro™ 435CDS
Reconfiguration Guide

Copyright
This manual is copyrighted by Toshiba Corporation with all rights reserved.
Under the copyright laws, this manual cannot be reproduced
in any form
without the prior written permission ofToshiba. No patent liability
is
assumed, however, with respect to the use ofthe information contained
herein.
© 1997 by Toshiba Corporation. All rights reserved.
Export Administration Regulation
This document contains technical data that may be controlled under the
U.S. Export Administration Regulations, and may be subject to the approval
of the U.S. Department of Commerce prior to export. Any export, directly
orindirectly, in contravention
of the U.S. Export Administration Regulation
is prohibited.
Disclaimer
This guide has been validated and reviewed for accuracy. The sets of
instructions were accurate for the Satellite Pro 430 Series and Satellite Pro
435CDS computers at the time
of this guide's production. However, suc-
ceeding computers and guides are subject
to change without notification.
Therefore, Toshiba assumes no liability for damages incurred directly or
indirectly from errors, omissions or discrepancies between the computer
and the guide.
Trademarks
MaxTime is a registered trademark, and AccuPoint, Fn-esse, magiCDisc
and Satellite Pro are trademarks
of Toshiba America Information Systems.
MS-DOS, Microsoft and Windows
are registered trademarks of Microsoft
Corporation.
TranXit
is a trademark of PumaTechnology, Inc.
All other brand and product names are trademarks or registered trademarks
oftheir respective companies.

Contents
Which Version of Windows Do You Use? ............................. 2
Reconfiguring a Windows 95 System .................................... 2
Before You Start ................................................................... 2
Preparing to Install ............................................................... 3
Turn Resume Mode Off .................................................... 3
Modify the Toshiba Companion Diskette ....................... .4
Installing Windows 95 ......................................................... 5
Selecting Components ...................................................... 8
Setting Up Microsoft Exchange .................................... 10
Installing the Display Drivers ............................................ 10
Installing Mediamatics Software MPEG .......................... 11
Installing Intel Video Interactive ....................................... 12
Installing the Toshiba Access PaneL ............................... 14
Installing Toshiba Fn-esse ................................................ 15
Installing magiCDisc .......................................................... 16
Installing TranXit ................................................................ 17
Verify the I rDA Port Settings ......................................... 18
Install T ranXit .................................................................. 19
Installing Sony Music Screeners ..................................... 21
Installing the Toshiba User's Guide .................................. 23
Installing Logitech MouseWare 95 .................................. 24
Installing the Companion Disk Utilities ............................ 25

•
IV
Installing CardWorks ......................................................... 26
Adding Suspend to the Start Menu ................................. 27
Modifying the Computer's Startup Files .... ...................... 27
Install Additional Programs .............................................. 28
Reconfiguring a Windows for Workgroups System .......... 29
Before You Start ...................................................... ........... 29
Install the Toshiba Companion Programs ....................... 30
Install MS-DOS 6.22 ......................................................... 31
Install Toshiba MS-DOS Enhancements ......................... 32
Install the System from CD-ROM .................................... 33
Install the System from -Diskettes .................................... 33
Install Windows .............................................................. 34
Install the Toshiba Windows Advanced Display
Driver ............................................................................... 34
Install MaxTime, Hardware Setup and Fn-esse ........... 35
Install the ESS Sound System ....................................... 36
Install magiCDisc ............................................................ 37
Install T ranXit2 ................................................................ 37
Install the AccuPoint Driver ............................................ 38
Install CardSoft ............................................... ................. 39
Install Intel Video Interactive .......................................... 40
Install MSVideo for Windows ........................................ 40
Install Windows QuickStart ........................................... 41
Install the Sony Screen Saver.. ...................................... 41
Edit the CONFIG.SYS and AUTOEXEC.BAT Files ......... 42
Install the Enhanced IDE Software ................................ 43
I nstall Online Help ........................................ ................... 44
Install the Microsoft Tools for Windows ...................... 45
Set Up Advanced Power Management for Windows .. 45
Install Additional Programs .............................................. 46
Satellite Pro ™430 Series/435CDS Reconfiguration Guide

Satell~e Pro™ 430 Series
Satell~e Pro™ 435CDS
Reconfiguration Guide
NOTE
Your computer comes with programs pre-installed on your
hard
drive. In the event you need to reinstall these programs,
follow these guidelines to reconfigure your computer to its
original factory setup.
Each section of this guide describes how to reinstall or recon-
figure one program or a group of pn?grams. If you need to
reinstall all of the pre-installed programs, start at the begin-
ning and work through
the entire guide. Otherwise, read only
the sections that apply to the programs you need to reinstall.
After following the instructions in this guide, all of the
pre-installed programs will be on your hard disk and
ready to use. The appearance of your desktop (if you're
using Windows@ 95) or Program Manager (if you're
using Windows@ for Workgroups) may be different than
when you turned the computer on the first time, but these
changes are cosmetic only and will not affect the opera-
tion of your programs.

2
Which Version of Windows Do You Use?
Before You Start
Which Version of Windows Do You Use?
This guide consists of two sections, one for Windows 95, and
the other for MS-DOS® and Wmdows for Workgroups. The
section
you use depends on the version of Wmdows you
chose when you turned your computer on for the first time:
.:. If you're using Wmdows 95, see "Reconfiguring a
Wmdows 95 System" on page 2.
• :. If you're using Windows for Workgroups, see "Reconfig-
uring a
Wmdows for Workgroups System" on page 29.
Reconfiguring a Windows 95 System
This section describes how to reinstall the pre-installed pro-
grams onto your hard disk if you chose to use Windows 95
when you turned the computer on the first time.
Before You Start
The instructions in this section make the following
assumptions:
.:. Your hard disk is already formatted.
• :. You'll install only the options that were pre-installed at the
factory.
To complete the steps in this guide, you'll need:
.:. A blank diskette
.:. The Microsoft® Wmdows 95 installation diskettes you
created using the Microsoft Create System Disks program
.:. The Toshiba diskettes you created using the Master Disk
Creator program
Satellite Pro™ 430 Senes/435CDSReconfiguration Guide

Reconfiguring a Windows 95 System 3
Preparing to Install
If you do not have these diskettes, create them now. Refer to
your computer's User 's Guide for instructions on running
Microsoft's Create System Disks
and Master Disk Creator.
The Satellite PrOTM 435CDS is pre-installed with
Wmdows 95 only, and comes with a Wmdows 95 CD-ROM
and a Windows 95 CD-ROM Setup Boot Disk. If you're
reconfiguring a Satellite
Pro 435CDS, do not modify the
Toshiba Companion Disk; instead, use the Wmdows 95
CD-ROM Setup Boot Disk and follow the CD-ROM installa-
tion steps.
Preparing to Install
EJ
CAUTION
Before you start the reconfiguration procedure, complete the
steps in the following sections.
Remove any PCMCIA-compatible PC Cards, external
monitors, or any other external devices attached to your
Toshiba computer before proceeding with this reconfigu-
ration. You can reattach these devices after the initial
reconfiguration.
Tum Resume Mode Off
Make sure the computer is not in Resume Mode. The fastest
way to do this is to use the hotkey combination Fn + F3:
1 Press and hold Fn, then press F3 to display the Resume
Mode pop-up window.
2 Continue holding Fn and press F3 toalternate between
Resume Mode
and BootMode.
3
When BootMode is selected, release both keys.
Satellite Pro™ 430 Senes/435CDS Reconfiguration Guide

4
[~]
CAUTION
Reconfiguring a Windows 95 System
Preparing to Install
Modify the Toshiba Companion Diskette
To install Wmdows 95 from a CD-ROM, you'll need to
have a bootable diskette that loads CD-ROM support. You
can create this diskette by modifying the CONFIG.SYS and
AUTOEXEC.BAT files on the Toshiba Companion Diskette
to enable the CD-ROM drivers.
DO NOT modify your Toshiba Companion Diskette if"
You are installing Windows 95 from diskettes.
You have the Windows 95 CD-ROM Setup Boot Disk
(provided with Satellite Pro 435CDS computers).
Follow these steps to modify the Toshiba Companion
Diskette:
1 Make sure the external diskette drive is connected to
thecomputer.
2 Write-enable the Toshiba CompanionDiskette.
The write-protect tab at the left comer of the diskette must
cover
the square hole.
3 Insertthe write-enabled Toshiba Companion Diskette
into the diskette drive.
4 Using a text editor, open the CONFIG.SYS
file onthe
diskette.
5 Locate theline
that reads rem device=a:\toscdrom.sys and
change itto read device=a:\toscdrom.sys.
6 Save the CONFIG.SYS file and close it.
7 Open the AUTOEXEC.BAT
file onthe diskette.
S Locate the lines that read:
rem if exist toscd001 a:\mscdex ID:TOSCD001 IM:10
acc.exe
Satellite Pro™ 430 Senes/435CDSReconfiguration Guide

Reconfiguring a Windows 95 System 5
InstallingWindows 95
9 Change the lines to:
if exist toscd001 a:\mscdex ID:TOSCD001 IM:10
rem acc.exe
10 Save the AUTOEXEC.BAT file and close it
11 Eject the modified Toshiba Companion Diskette from
the diskette drive.
You will use this disk in place of the Windows 95 Setup
Boot Disk
in the following sections.
Installing Windows 95
This section describes how to install Windows 95 using either
the diskettes you created using the Microsoft System Disks
program or a
Wmdows 95 CD-ROM. Follow these steps:
1 If you're installing from a CD-ROM, make sure the
external diskette drive is connected to the computer
and the CD-ROM module is installed in the com-
puter's SelectBay.
2 Insert a bootable diskette into the diskette drive:
.:. If you're reinstalling software on a Satellite Pro
435CDS, insert
the Wmdows 95 Setup Boot Disk.
You received this diskette with your computer.
• :. If you're reinstalling software on aSatellite Pro 430
Series computer from diskettes, insert the Windows 95
Setup Boot Disk.
You created this diskette using the Microsoft Create
System Disks program.
• :. If you're reinstalling software on aSatellite Pro 430
Series computer from CD-ROM, insert the modified
Toshiba Companion Diskette.
If you haven't modified this diskette, refer to "Modify
the Toshiba Companion Diskette" on page 4.
Satellite Pro™ 430 Senes/435CDSReconfiguration Guide

6
Reconfiguring a Windows 95 System
Installing Windows 95
3 'fum your computer off, then on, to restart it
If you inserted the Wmdows 95 Setup Boot Disk, the sys-
tem restarts and displays the Welcome to Setup screen.
Press
Enter.
If you inserted the modified Toshiba Companion Diskette,
the system restarts and displays a DOS command
prompt (A:\».
4 Insert the discldiskette and start the Setup program:
.:. If you're reinstalling software from CD-ROM, insert
the Wmdows 95 CD-ROM into the computer's
CD-ROM drive, type d:\setup and press Enter .
• :. If you're reinstalling software from diskettes, insert
diskette 1into the diskette
drive and press Enter.
You created this diskette using Microsoft Create
System Disks.
The Setup program displays the message, "Setup
is now
going to perform a routine check on your system."
5 Press Enter.
Setup begins to load files onto your system, and displays
the Welcome to Wmdows 95 Setup screen.
6 Click Continue.
Setup displays a message that it is preparing the
Windows
95 Setup Wizard.
7 If you are reinstalling software from diskettes, insert
additional diskettes
as the system prompts you.
Setup displays the Software License Agreement screen.
8 Click
Yes to agree to the license agreement
Setup displays the Windows 95 Setup Wizard with "Col-
lecting Information about
Your Computer."
Satellite Pro™ 430Senes/435CDS Reconfiguration Guide

NOTE
Reconfiguring a Windows 95 System 7
InstallingWindows 95
9 Click Next
Setup prompts you to choose a directory. ,
10 Accept the default (c:\windows) byclicking Next
Setup displays the Setup Options screen.
11 Select Custom, and click Next
12 Enter the ProductIdentification Numberfrom the
Certificate
of Authenticity.
13 Click
Next
14 Enter your name and company if requested and click
Next
15 Click Next
16 Select components to install:
.:. If you're installing from CD-ROM, select Sound,
MIDI
or Video Capture Card.
•:. If you're installing from diskettes, select CD-ROM
drive and Sound, MIDI or Video Capture Card.
Don 't select Network Adapter.
17 Click Next.
Setup performs a hardware scan of your computer, then
displays the Get Connected screen.
18 Select any items that apply (i.e., Microsoft Network,
Microsoft Mail
or Microsoft Fax) and click Next.
Satellite Pro™ 430 Senes/435CDSReconfiguration Guide

8
Reconfiguring a Windows 95 System
Installing Windows 95
Selecting Components
1 When Setupdisplays the Select Components screen,
select the items listed
in the following table by clicking
in the box to the left of the item. Click OK aftereach
component.
A check mark appears when the item is selected.
For these components, select these items andclick OK.
Accessories All
Communications All except Direct Cable
Disktools Backup
Windows messaging All
Microsoft Fax All
Multimedia Audio Compression
CD Player
Media Player
Sample Sounds
Sound Recorder
Video Compression
Volume Control
The Microsoft Network The Microsoft Network
2 When aU changes have been made, click Next to
continue.
Setup displays the Network Configuration screen.
3 Makeany necessary changes, and click Next to
continue.
Setup may display the Identification screen.
Satellite Pro™ 430 Series/435CDS Reconjiguration Guide

Reconfiguring a Windows 95 System 9
InstallingWindows 95
4 If requested, enteryour name and otheridentification
infonnation, then click Next to continue.
Setup displays the ComputerSettings screen.
5 Click Next.
Setup displays the Startup Disk screen.
6 Select Yes and click Next.
The Setup Wizard indicates that it is copying files.
7 When requested to do so, inserta blank diskette into
the diskette drive.
8 Click Next.
9
When the copy is finished, remove the disk and
click OK.
10 Label the diskette "Windows 95 Setup Boot Disk."
11 Click Next and insertadditional diskettes as thesys-
tem prompts you.
12 When Setupdisplays theFinishing Setup message,
remove the diskette from the drive
and click Finish.
The computer restarts.
13 Enter user's name and Windows password as the
screen instructs you.
14 Click OK.
15 Confinnyour password as the screen instructs you.
The computer sets up Hardware, Control Panel, Programs
on the StartMenu, Windows Help, the MS-DOS program
settings, Time Zone and Microsoft Exchange.
16 When the system displays the Time Zone date and
time screens, make any necessary changes, then
click OK.
Satellite Pro™ 430 Series/435CDS Reconfiguration Guide

10
Reconfiguring a Windows 95 System
Installing the Display Drivers
Setting Up Microsoft Exchange
If you chose MicrosoftExchange, Setup prompts you to con-
firm your selections.
1 Whenasked if you'veusedMicrosoftExchangebefore,
click Cancel.
2 Click
Yes.
You can add your printer at this time, or click Cancel.
Installing the Display Drivers
1 Insert the discldiskette containing the files:
.:. If you're installing from CD-ROM, insert the Toshiba
Pre-installed Software CD-ROM into the CD-ROM
drive.
• :. If you're installing from diskettes, insert the display
drivers diskette into the diskette drive.
2 Clickan unused area of the desktop with the second-
ary AccuPoint™ button.
Windows 95 displays a shortcut menu.
3 Click Properties.
Windows 95 displays the Display Properties dialog box.
4 Click the Settings tab.
The Settings tab moves to the front of the dialog box.
5 Click Advanced Properties.
Windows 95 displays the Advanced Display Properties
dialog box.
6 In the Adapter section of the dialog box, click Change.
Wmdows 95 displays the Select Device dialog box.
Satellite Pro™ 430Series/435CDS Reconfiguration Guide

Reconfiguring a Windows 95 System 11
InstallingMediamaticsSoftware MPEG
7 Click Have Disk.
Wmdows 95 displays the Install From Diskdialog box.
8 If you're installingfrom:
.:. CD-ROM, type d:\chips in the "Copy manufacturer's
files from" box and click
OK .
•:. Diskettes, type
a:\ in the "Copy manufacturer's files
from" box and click OK.
Windows 95 displays the Select Device dialog box.
The model will
be Chips and Technologies, Accelerator
(New).
9 Click OK to install the driver.
10 After Windows 95 finishes copying the files, click
Close.
11 Change the size of the Desktop area to 800 by 600
pixels, then click Apply.
12 You
may be prompted to specify yourmonitor type. If
so, select Laptop Display Panel (800 x 600) and
click OK.
13 Restart the computeras prompted.
Installing Mediamatics Software MPEG
This procedure installs the Mediamatics Arcade Media
Player.
1 Insertthe disc/diskette containing the files:
.:. If you're installing from CD-ROM, insert the Toshiba
Pre-installed Software
CD-ROM into the CD-ROM
drive.
•:. If you're installing from diskettes, insert the MPEG-l
Arcade Playerfor Wmdows 95 disk 1 into the diskette
drive.
Satellite Pro™ 430Senes/435CDSReconfiguration Guide

12
Reconfiguring a Windows 95 System
Installing Intel Video Interactive
2 If you're installing from CD-ROM,follow these steps:
a Double-click
the My Computer icon.
Windows 95 opens the My Computer window.
b Click the CD-ROM drive icon (d:\) with the sec-
ondary AccuPoint button.
Windows 95 displays a shortcut menu.
c Click Install Mediamatics Media Player.
d
Press Enter toagreeto the MPEG Arcade95 License
Agreement
3 If you're installing from diskette, follow these steps:
a Click
Start, then click Run.
Windows 95 displays the Run dialog box.
b Type a:\setup and click OK.
The Setup program starts.
c Press Enter toagree to the MPEG Arcade95 License
Agreement
4 Press Enter.
5 Restart the computer as instructed.
Installing Intel Video Interactive
1 Insert the disc/diskette containing the files:
.:. If you're installing from CD-ROM, insert the Toshiba
Pre-installed Software CD-ROM into
the CD-ROM
drive.
• :. If you're installing from diskettes, insert the Intel
Video Interactive diskette into the diskette drive.
Satellite Pro™ 430 Series/435CDS Reconfiguration Guide

Reconfiguring a Windows 95 System 13
Installing Intel Video Interactive
2 If you're installing from CD-ROM,follow these steps:
a Double-click the
My Computer icon.
Windows 95 opens the My Computer window.
b· Click the CD-ROM drive icon (d:\) with the sec-
ondary AccuPoint button.
Windows 95 displays a shortcut menu.
c Click InstallIndeo Video Interactive (32-bit).
3
If you're installingfrom diskette, follow these steps:
a Click Start, then click Run.
Wmdows 95 displays the Run dialog box.
b Type a: \setup and click OK.
The Setup program starts.
4 Click Next.
5 Select Windows 95 System (thedefault)
and click Next
6 Click OK.
7 Click Yes to view the Readme information.
Click No to exit without viewing the Readme information.
S If you clicked Yes, read the Readme information, then
close the Indeo READlVIE window by clicking its close
button.
Satellite Pro™ 430 Senes/435CDSReconfiguration Guide

14
Reconfiguring a Windows 95 System
Installing the Toshiba Access Panel
Installing the Toshiba Access Panel
~]
CAunON
This procedure installs the Toshiba Access Panel (TAP).
Make sure the Windows Control Panel isn't open when
you begin this procedure. Following these steps with
Control Panel open may result in an improper
installation .
1 Insertthe disc/diskette containing the files:
.:. If you're installing from CD-ROM, insert the Toshiba
Pre-Installed Software CD-ROM into
the CD-ROM
drive.
• :. If you're installing from diskettes, insert the
Wmdows
95 Utilities diskette into the diskette drive.
2 If you're installing from CD-ROM,follow these steps:
a Double-click the My Computericon.
Windows
95 opens the My Computer window.
b Click the CD-ROM drive icon (d:\) with the sec-
ondary AccuPoint button.
Wmdows
95 displays a shortcut menu.
c Click InstallToshiba Access Panel.
3
If you're installing from diskette, follow these steps:
a Click Start,then click Run.
Wmdows 95 displays the Run dialog box.
b Type a:\setup and click OK.
Setup displays the Installing TAP System welcome screen.
4 Click Next.
Satellite Pro™ 430Series/435CDS Reconjiguration Guide

Reconfiguring a Windows 95 System 15
Installing Toshiba Fn-esse
5 Click Next to accept thedefault path of c:\toshiba\tap\.
Setup copies the program files.
6 If you'reinstallingfrom diskettes, insertadditional dis-
kettes as the system promptsyou.
7 Click
Yes to view the Readme file.
S Click Finish.
9
If you clicked Yes, read the Readme information, then
close the TAP Readme window
by clicking its close
button.
10 Remove thediskette from thediskette drive.
11 Click Finish to restartthe computer.
Installing Toshiba Fn-esse
Follow these steps to reinstall the Toshiba Fn-esse™program:
1 Insertthe disc/diskette containing the files:
.:. If you're installing from CD-ROM, insert the Toshiba
Pre-Installed Software CD-ROM into
the CD-ROM
drive .
•:. If you're installing from diskettes, insert the
Windows 95 Utilities diskette into the diskette drive.
2 If you'reinstallingfrom CD-ROM,follow these steps:
a Double-click the
My Computericon.
Windows 95 opens the My Computer window.
b Click the CD-ROM drive icon (d:\) with the sec-
ondaryAccuPointbutton.
Wmdows 95 displays a shortcut menu.
c ClickInstall Toshiba Fn-esse.
Satellite Pro™ 430 Series/435CDS Reconfiguration Guide