Toshiba RemotEye II User manual

Document 60763-000
RemotEye II Quick Installation Guide
Windows Users

Document 60763-000
Installing RemotEye II/Internal
Follow these steps to install the RemotEye II/Internal card.
a) Slide the RemotEye II/Internal printed circuit board into the
extension option slot of the UPS.
b) Secure the printed circuit board using the UPS-supplied
screws.(See Error! Reference source not found.)
Installing RemotEye II/External
Follow these steps to install the RemotEye II/External device.
a) Insert the power adapter cable of the RemotEye II into
the 12 VDC power receptacle of the RemotEye II
device.
b) Plug the RemotEye II power adapter into a 120/220
VAC power source. For best results, be sure outlet is
powered by a Toshiba UPS.
c) Connect the UPS cable from the RS232 serial port of
the Toshiba UPS to the RemotEye II/External UPS
port.(See Error! Reference source not found.)
Configuration
RemotEye II must be configured for proper operation on its network.
Configuring the RemotEye II via Terminal
The RemotEye II can be configured by directly connecting to the device.
Hardware Setup
Direct configuration is accomplished through the provided cable. Follow these steps to setup the
hardware for direct RemotEye II configuration:
a) Connect the DB9 female end of the PC cable to the terminal or workstation COM port.
b) Connect the RJ45 end of the PC cable to the PC port of RemotEye II/External or the
COM port of the RemotEye II/Internal.
Software Setup
The direct configuration is accomplished by using the RS232 communication protocol.
The direct communication can be performed from a workstation running Terminal
Emulator Software (TES)
Connecting to the RemotEye II via Terminal
A direct configuration session can easily be established once the hardware and software are
properly set up. Follow these steps to begin configuration:
Figure 1: RemotEye II/Internal
Figure 2: RemotEye II/External

Document 60763-000
Terminal Emulator Example
To configure the RemotEye II from a Windows platform, use Hyperterminal. Hyperterminal is a
standard terminal emulator packaged with any Windows operating system. Launch the
Hyperterminal program by navigating to Start →Programs →Accessories →Hyperterminal
→Hyperterminal, and follow the prompts.
Enter a name and select an icon for the application at the Connection Dialog box.
Select a direct connection to an appropriate com port listed in the pull-down menu.
Ensure that the Properties dialog box is setup as follows:
Baud Rate — 9600
Data Bits — 8
Parity — None
Stop Bits — 1
Flow Control —- None
Press [Enter] and the RemotEye II version and Password field will be displayed (see Error!
Reference source not found.).
Enter the password (default is “public”) and press [Enter] to display the RemotEye II Main Menu.
+====================================================================+
| [ TIC RemotEye II Login Menu ] |
+====================================================================+
Enter Password: ******
The seven options provided in the RemotEye II Main Menu provide access to all system
RemotEye II configuration parameters. These options (see the Main Menu Description on Figure
4: Console Main Menu) and their submenus are discussed in more detail in the next section.
+====================================================================+
| [ TIC RemotEye II Main Menu ] |
+====================================================================+
1. TIC RemotEye Configuration
2. SNMP Communities
3. SNMPV3 USM Table
4. Trap Receiver Table
5. Reset Configuration To Default
6. Save and Exit
7. Save and Restart Agent
Please Enter Your Choice =>
Figure 4: Console Main Menu
Figure 3: Console Login Screen

Document 60763-000
Toshiba RemotEye II Configuration
Main Menu →(1)Toshiba RemotEye II Configuration (see Figure 5: Console Configuration
Menu Description).
+==================================================================+
| [ TIC RemotEye II Configuration Menu ] |
+==================================================================+
1. System Group
2. Control Group
3. Parameter Group
4. Email Group
5. EMD Group
0. Return to previous menu
Please Enter Your Choice =>
Figure 5: Console Configuration Menu Description
System Group
Main Menu →(1)Toshiba RemotEye II Configuration →(1)System Group (see Figure 6: Console
System Group Menu Description).
The System Group provides access to the system settings listed below. The settings may be
viewed or changed from this screen. When using the Dynamic Host Configuration Protocol
(DHCP), items 1 – 3 will be retrieved automatically.
+====================================================================+
| [ System Group Menu ] |
+====================================================================+
RemotEye II Agent Version : TIC RemotEye II v3.00
Ethernet address : 00 E0 D8 08 80 0D
1. Ip Address : 172.18.1.63
2. Gateway Address : 172.18.1.1
3. Network Mask : 255.255.240.0
4. Date and Time
0. Return to previous menu
Please Enter Your Choice =>
Figure 6: Console System Group Menu Description
Making the Network Connection
Each Ethernet network is different. Therefore, the following steps should be used as an outline
for connecting the RemotEye II to a network:
a) Connect one end of a Category 5 cable to the NETWORK RJ45 receptacle of
RemotEye II.
b) Connect the other end of the Category 5 cable to a designated network switch or hub. A
network administrator will allocate an available port.
c) Verify a network link has been established. On RemotEye II/External, confirm Traffic
LED on RemotEye II is illuminated. On RemotEye II/Internal, confirm the leftmost,
green LED is illuminated

Document 60763-000
Connecting to the RemotEye II via HTTP
A web session can be established once the hardware and software have been prepared. Follow
these steps to begin configuration:
c) Launch the web browser.
d) Enter the URL for RemotEye II in the browser’s address field. For example,
http://10.0.37.189. The home page of the RemotEye II will be displayed once a
connection is established (see Error! Reference source not found.).
Figure 7: RemotEye II HTTP Page

Document 60763-000
Upgrading RemotEye II Firmware from Windows via Network
Figure 8: Tugrade, RemotEye II Upgrade Utility via Network
The RemotEye II firmware may be upgraded from a Windows platform by performing the
following procedure.
a) A PC with a Windows 95/98, 2000, NT, XP, or Vista operating system installed will be
required for this procedure.
b) On the PC, create a directory named Upgrade and copy the contents of the RemotEye II
Upgrade CD-ROM to the Upgrade directory.
c) For network upgrade, ensure that DIP switches 1 and 2 of the RemotEye II are off.
d) From the Control Group menu, set the TFTP Upgrade Control to Enabled.
e) From the Upgrade directory, run Tupgrade.exe and a dialog box will be displayed.
f) Click Discover to search for the RemotEye II on the network.
g) Select the RemotEye II to be upgraded and enter the password.
h) Click Open to load the upgrade file.
i) Path to the upgrade file and select the latest version.
j) Click Upgrade to transfer the file to the upgradeable read-only memory of the RemotEye
II.
k) When the transfer is complete the RemotEye II will reboot.

Document 60763-000
User Manual
The full RemotEye II User Manual (P/N 500024) is provided on the enclosed CD in
electronic (PDF) format.
Contacting the TOSHIBA Customer Support Center
TOSHIBA’s Customer Support Center can be contacted to obtain help in resolving any
RemotEye II system problem that you may experience or to provide application
information.
The Support Center can be reached at 877-867-8773 (toll free) or 713-466-0277. The
center is open from 8 a.m. to 5 p.m. (CST), Monday through Friday.
You may also contact TOSHIBA by writing to:
TOSHIBA International Corporation
13131 West Little York Road
Houston, Texas 77041-9990.
For further information on TOSHIBA’s products and services, please visit our website at
HTTP://WWW.TOSHIBA.COM/IND.