Toshiba MK8009GAH Quick start guide

MK4009GAL/MK8009GAH P/N 480077-A0 P/N 480077-A0 MK4009GAL/MK8009GAH
Hard Disk Drive Installation Notes 07/06 07/06 Hard Disk Drive Installation Notes
TOSHIBA STORAGE DEVICE DIVISION
MK4009GAL & MK8009GAH
HDD INSTALLATION NOTES
© 2006 Toshiba America Information Systems, Inc.
Contents subject to change without prior notice.
GENERAL DESCRIPTION
Toshiba’s MK4009GAL (HDD1622) and MK8009GAH (HDD1584) hard disk drives
are a series of ultra-slim fast light weight 1.8 inch Winchester disk drive. The drives are
ATA-6 compliant.
SPECIFICATIONS MK4009GAL MK8009GAH
HDD1622 HDD1584
FORMATTED CAPACITY 40.0GB 80.0GB
HEIGHT 5mm 8mm
WEIGHT 1.69oz (48g) 2.08oz (59g)
NO. OF DISKS (PLATTERS) 1 2
NO. OF DATA HEADS 2 4
FUNCTIONAL SPECIFICATION
LOGICAL DRIVE MK4009GAL MK8009GAH
PARAMETERS HDD1622 HDD1584
NO. OF CYLINDERS (user) 62,640 62,640
BYTES PER SECTOR 512 512
BUFFER SIZE 8MB 2/8MB
ROTATION SPEED (±0.1%) 4,200rpm
TRANSFER RATE INTERNAL 165.0 - 356.8 Mbits/sec.
NO. OF CYLINDERS (logical) 16,383
NO. OF HEADS (logical) 1 6
NO. OF SECTORS/TRACK 6 3
HOST TRANSFER RATE
PIO/ULTRA DMA (ATA mode) 16.6/100MB/s
SEEK TIME
AVERAGE 15ms
TRACK-TO-TRACK 3ms
MAXIMUM 26ms
TEMPERATURE
OPERATING 41°F - 140°F (5°C - 60°C)
NON-OPERATING -4°F - 149°F (-20°C - 65°C)
HUMIDITY
OPERATING/NON-OPERATING 8 - 90% R.H. (No condensation)
SHIPPING 5 - 90% R.H. (No condensation)
WET BULB 29°C(operating)/40°C(non-operating)
CONNECTOR CABLING INFORMATION
The following table describes all of the pins on the Task File Interface:
PIN SIGNALS PIN SIGNALS
1 RESERVED 2 RESERVED
3 - RESET 4 GROUND
5 DD7 6 DD8
7 DD6 8 DD9
9 DD5 10 DD10
11 DD4 12 DD11
13 DD3 14 DD12
15 DD2 16 DD13
17 DD1 18 DD14
19 DD0 20 DD15
21 GROUND 22 DMARQ
23 GROUND 24 - DI0W
STOP
25 -DIOR 26 GROUND
-HDMARDY
HSTROBE
27 IORDY 28 GROUND
-DMARDY
DSTROBE
29 DMACK 30 INTRQ
31 DA1 32 - PDIAG/-CBLID
33 DA0 34 DA2
35 -CS0 36 -CS1
3 7 - DASP 3 8 +3.3V
39 +3.3V 40 RESERVED
Note: “-“ in front of signal name indicates negative logic.

MK4009GAL/MK8009GAH P/N 480077-A0 P/N 480077-A0 MK4009GAL/MK8009GAH
Hard Disk Drive Installation Notes 07/06 07/06 Hard Disk Drive Installation Notes
UNPACKING PROCEDURE
Visually inspect the shipping container prior to unpacking for any signs of damage to
the container or its contents (the carrier is responsible for any damage incurred during
shipment). Prior to opening the anti-static bag, it is recommended that the user ground
himself with a ground strap or by touching the PC chassis or other metal object. Re-
move the drive from the anti-static bag and check it for damage. Save the shipping
container and packing material for possible use later.
HANDLING AND MOUNTING CONSIDERATIONS
•Installation and mounting of these drives is specific to the application environment.
•Handle drive only by the edges. When handling or mounting, take care not to apply
any pressure to the top cover.
•Avoid subjecting the drive to excessive shock. Do not drop the drive, even a
small distance onto a tabletop or other hard surface can damage drive. When
mounting the drive, do so in such a fashion that the drive will be isolated from
excessive shock.
•Do not mount in an environment where the temperature of the drive’s top cover will
exceed 65°C. (During operation, the temperature of the top cover can rise 15°C
above ambient).
•Do not disassemble, modify or repair drive.
•A rattle heard when the drive is moved is normal and not a sign of failure.
INTERFACE CONNECTOR
Drive Side Connector DDK Ltd, FF19A-40B-R11b
Recommended host side FPC 1. Width: 20.50 ±0.07mm
2. Thickness: 0.20 ±0.03mm
3. Length: 90mm (max)
4. Impedance: Typical 50ohm
5. Plating: Gold over Nickel plating (note 1)
6. Adhesive: Heat-hardened adhesive
Connector Durability (note 2) 20 times
FPC Holding fource (note 3) Typ: 17[N] Min: 5[N]
* Do not pull out FPC with the connector locked.
* Do not lock without FPC
Notes:
1. To avoid Sn whisker
2. In horizontal direction with FPC of 0.20mm in thickness and with the same
connector and FPC
3. In horizontal direction with FPC of 0.20mm in thickness and with the same
connector and FPC after pulling out repeatedly
FIGURE 1 – INTERFACE CONNECTOR
DEVELOPER SUPPORT
Toshiba Storage Device Division (SDD) the industry pioneer in small form factor
storage supports developers who are looking for small form factor HDD’s that deliver
the unbeatable combination of high-performance and high-capacity storage. Toshiba
HDD’s can be found “under the hood” of some of today’s hottest portable products. If
you are interested in discussing your product application with us please contact us.
E-mail: [email protected]
Phone: [phone]
Fax: [phone]
Web: http://developer.toshiba.com

MK4009GAL/MK8009GAH P/N 480077-A0 P/N 480077-A0 MK4009GAL/MK8009GAH
Hard Disk Drive Installation Notes 07/06 07/06 Hard Disk Drive Installation Notes
UNPACKING PROCEDURE
Visually inspect the shipping container prior to unpacking for any signs of damage to
the container or its contents (the carrier is responsible for any damage incurred during
shipment). Prior to opening the anti-static bag, it is recommended that the user ground
himself with a ground strap or by touching the PC chassis or other metal object. Re-
move the drive from the anti-static bag and check it for damage. Save the shipping
container and packing material for possible use later.
HANDLING AND MOUNTING CONSIDERATIONS
•Installation and mounting of these drives is specific to the application environment.
•Handle drive only by the edges. When handling or mounting, take care not to apply
any pressure to the top cover.
•Avoid subjecting the drive to excessive shock. Do not drop the drive, even a
small distance onto a tabletop or other hard surface can damage drive. When
mounting the drive, do so in such a fashion that the drive will be isolated from
excessive shock.
•Do not mount in an environment where the temperature of the drive’s top cover will
exceed 65°C. (During operation, the temperature of the top cover can rise 15°C
above ambient).
•Do not disassemble, modify or repair drive.
•A rattle heard when the drive is moved is normal and not a sign of failure.
INTERFACE CONNECTOR
Drive Side Connector DDK Ltd, FF19A-40B-R11b
Recommended host side FPC 1. Width: 20.50 ±0.07mm
2. Thickness: 0.20 ±0.03mm
3. Length: 90mm (max)
4. Impedance: Typical 50ohm
5. Plating: Gold over Nickel plating (note 1)
6. Adhesive: Heat-hardened adhesive
Connector Durability (note 2) 20 times
FPC Holding fource (note 3) Typ: 17[N] Min: 5[N]
* Do not pull out FPC with the connector locked.
* Do not lock without FPC
Notes:
1. To avoid Sn whisker
2. In horizontal direction with FPC of 0.20mm in thickness and with the same
connector and FPC
3. In horizontal direction with FPC of 0.20mm in thickness and with the same
connector and FPC after pulling out repeatedly
FIGURE 1 – INTERFACE CONNECTOR
DEVELOPER SUPPORT
Toshiba Storage Device Division (SDD) the industry pioneer in small form factor
storage supports developers who are looking for small form factor HDD’s that deliver
the unbeatable combination of high-performance and high-capacity storage. Toshiba
HDD’s can be found “under the hood” of some of today’s hottest portable products. If
you are interested in discussing your product application with us please contact us.
E-mail: [email protected]
Phone: [phone]
Fax: [phone]
Web: http://developer.toshiba.com

MK4009GAL/MK8009GAH P/N 480077-A0 P/N 480077-A0 MK4009GAL/MK8009GAH
Hard Disk Drive Installation Notes 07/06 07/06 Hard Disk Drive Installation Notes
TOSHIBA STORAGE DEVICE DIVISION
MK4009GAL & MK8009GAH
HDD INSTALLATION NOTES
© 2006 Toshiba America Information Systems, Inc.
Contents subject to change without prior notice.
GENERAL DESCRIPTION
Toshiba’s MK4009GAL (HDD1622) and MK8009GAH (HDD1584) hard disk drives
are a series of ultra-slim fast light weight 1.8 inch Winchester disk drive. The drives are
ATA-6 compliant.
SPECIFICATIONS MK4009GAL MK8009GAH
HDD1622 HDD1584
FORMATTED CAPACITY 40.0GB 80.0GB
HEIGHT 5mm 8mm
WEIGHT 1.69oz (48g) 2.08oz (59g)
NO. OF DISKS (PLATTERS) 1 2
NO. OF DATA HEADS 2 4
FUNCTIONAL SPECIFICATION
LOGICAL DRIVE MK4009GAL MK8009GAH
PARAMETERS HDD1622 HDD1584
NO. OF CYLINDERS (user) 62,640 62,640
BYTES PER SECTOR 512 512
BUFFER SIZE 8MB 2/8MB
ROTATION SPEED (±0.1%) 4,200rpm
TRANSFER RATE INTERNAL 165.0 - 356.8 Mbits/sec.
NO. OF CYLINDERS (logical) 16,383
NO. OF HEADS (logical) 1 6
NO. OF SECTORS/TRACK 6 3
HOST TRANSFER RATE
PIO/ULTRA DMA (ATA mode) 16.6/100MB/s
SEEK TIME
AVERAGE 15ms
TRACK-TO-TRACK 3ms
MAXIMUM 26ms
TEMPERATURE
OPERATING 41°F - 140°F (5°C - 60°C)
NON-OPERATING -4°F - 149°F (-20°C - 65°C)
HUMIDITY
OPERATING/NON-OPERATING 8 - 90% R.H. (No condensation)
SHIPPING 5 - 90% R.H. (No condensation)
WET BULB 29°C(operating)/40°C(non-operating)
CONNECTOR CABLING INFORMATION
The following table describes all of the pins on the Task File Interface:
PIN SIGNALS PIN SIGNALS
1 RESERVED 2 RESERVED
3 - RESET 4 GROUND
5 DD7 6 DD8
7 DD6 8 DD9
9 DD5 10 DD10
11 DD4 12 DD11
13 DD3 14 DD12
15 DD2 16 DD13
17 DD1 18 DD14
19 DD0 20 DD15
21 GROUND 22 DMARQ
23 GROUND 24 - DI0W
STOP
25 -DIOR 26 GROUND
-HDMARDY
HSTROBE
27 IORDY 28 GROUND
-DMARDY
DSTROBE
29 DMACK 30 INTRQ
31 DA1 32 - PDIAG/-CBLID
33 DA0 34 DA2
35 -CS0 36 -CS1
3 7 - DASP 3 8 +3.3V
39 +3.3V 40 RESERVED
Note: “-“ in front of signal name indicates negative logic.