Toshiba G9000 SERIES User manual

Part # 201642-000
November 2019
© Copyright 2019 TOSHIBA International Corporation
All rights reserved.
G9000 Series
SCiB Energy Storage System
HMI INSTALLATION INSERT

iSCiB ESS HMI Installation Insert - 201624-000
Purpose
This insert provides information on how to safely install your Toshiba International Corporation power electronics product.
The manual accompanying this insert includes a section of general safety instructions that describes the warning labels
and symbols that are used throughout the manual. Read the manual completely before installing, operating, or performing
maintenance on this equipment.
The manual, this insert, and the accompanying drawings should be considered a permanent part of the equipment and
should be readily available for reference and review. Dimensions shown in the manual are in metric and/or the English
customary equivalent.
Toshiba International Corporation reserves the right, without prior notice, to update information,
make product changes, or discontinue any product or service identied in this publication.
(See https://www.toshiba.com/tic/industrial/uninterruptible-power-systems. )
Toshiba and SCiB are registered trademarks of the Toshiba Corporation. All other product or trade references appearing in
this manual are registered trademarks of their respective owners.
Toshiba International Corporation shall not be liable for direct, indirect, special, or consequential damages resulting from the
use of the information contained within this manual.
This manual is copyrighted. No part of this manual may be photocopied or reproduced in any form without the prior written
consent of Toshiba International Corporation.
© Copyright 2019 Toshiba International Corporation
All rights reserved.
Printed in the U.S.A.
Toshiba Customer Support Center
Contact the Toshiba Customer Support Center for assistance with application information or for any problems that you may
experience with your Toshiba SCiB Energy Storage System.
Toshiba Customer Support Center
8 a.m. to 5 p.m. (CST) – Monday through Friday
USA Toll Free [phone]
Tel [phone] Fax [phone]
E-mail – [email protected]
Web – https://www.toshibaups.com
You may also contact Toshiba by writing to:
TOSHIBA INTERNATIONAL CORPORATION
SOCIAL INFRASTRUCTURE SYSTEMS GROUP
POWER ELECTRONICS DIVISION
13131 West Little York Road
Houston, Texas 77041-9990
Attn.: Power Electronics Division – UPS
For further information on Toshiba products and services, please visit our website at:
www.toshiba.com/tic/industrial/uninterruptible-power-systems

ii SCiB ESS HMI Installation Insert - 201624-000
Table of Contents
1 Introduction............................................................................................................................... 1
2 Hardware Contents................................................................................................................... 2
3 Installation Procedure.............................................................................................................. 2
3.1 Install HMI into Mounting Bracket: ................................................................................... 2
3.2 Install HMI assembly onto ESS Cabinet: ........................................................................ 2
3.3 Wiring Connections:......................................................................................................... 2
Table of Figures
Figure 3.1: HMI Installation Overview......................................................................................... 3
Figure 3.2: HMI Bracket (PN 200866), Front View ..................................................................... 4
Figure 3.3: HMI Bracket (PN 200866), Back View...................................................................... 4
Figure 3.4: HMI Screen (200134), front view.............................................................................. 5
Figure 3.5: HMI Screen (200134), back view ............................................................................. 5
Figure 3.6: HMI assembly, proper orientation............................................................................. 5
Figure 3.7: HMI Assembly, front view ......................................................................................... 6
Figure 3.8: HMI mounting clips................................................................................................... 6
Figure 3.9: HMI clip installation view .......................................................................................... 7
Figure 3.10: Securing HMI to Bracket......................................................................................... 7
Figure 3.11: Completed assembly .............................................................................................. 8
Figure 3.12: Cover plate for removal, front view......................................................................... 8
Figure 3.13: Cover plate removal, back view.............................................................................. 8
Figure 3.14: Cover Plate Removed ............................................................................................ 9
Figure 3.15: HMI Assembly mounted on door ............................................................................ 9
Figure 3.16: HMI assembly, installed, front view ...................................................................... 10
Figure 3.17: HMI Connection point 78704................................................................................ 10
Figure 3.18: 78703 Wirekit Diagram......................................................................................... 10
Figure 3.19: 78704 Wirekit Diagram..........................................................................................11
Figure 3.20: HMI Wiring Schematic.......................................................................................... 12

1SCiB ESS HMI Installation Insert - 201624-000
1 Introduction
This insert provides information on how to safely install the Human–Machine Interface (HMI) Option for the G9000 Series
SCiB Energy Storage System (ESS). The SCiB ESS Manual (PN 98485) includes a section of general safety instruc-
tions that describes the warning labels and symbols that are used throughout the manual. Read the SCiB ESS Manual
completely before installing, operating, performing maintenance on the equipment, or taking any actions described in this
insert.
Qualied personnel should read the SCiB ESS manual carefully before transporting, installing, and wiring the SCiB ESS. In
addition they should have a thorough understanding of the information provided in the chapters titled:
• General Safety Instructions
• Important Safety Instructions
• Safety Precautions
• Installation Precautions
Read this SCiB ESS Installation and Operation Manual for important instructions on operating the G9000 UPS with the SCiB
ESS. This insert and the accompanying drawings should be considered a permanent part of the equipment and should be
readily available for reference and review.
Keep the Installation Manual and the Operation Manual near the SCiB ESS for necessary reference.
Dimensions shown in the manual are in metric and/or the English customary equivalent.
SAVE THESE INSTRUCTIONS

2SCiB ESS HMI Installation Insert - 201624-000
2 Hardware Contents
The following table shows the bill of material for the HMI Option kit.
TABLE 2.1: HMI KIT BILL OF MATERIAL
TIC PN Description Quantity
201334 HMI DISPLAY 7IN WDSCRN TFT 1
200866 BRKT HMI EXOR07_RES-TOUCH 1
201639 WIRE KIT MULTI HMI SCiB 1
201624 SCiB ESS HMI INSTALLATION MANUAL 1
3 Installation Procedure
Refer to Figure 3.1 for Installation Overview when following the below procedure.
3.1 Install HMI into Mounting Bracket:
1. Locate the HMI Mounting Bracket (PN 200866) and remove from packaging. (Figure 3.2 & Figure 3.3)
2. Locate the HMI Display (PN 201334). (Figure 3.4 & Figure 3.5)
3. Remove HMI Display from packaging, keeping the (4) mounting clips with screws available.
4. Slide HMI Display (PN 201334) onto HMI Mounting Bracket (200866). Ensure you can clearly read the
connection ports on the backside of the HMI screen, this will indicate you have placed the screen in its proper
orientation. (Figure 3.6)
5. Secure the (4)clips onto the HMI by aligning them to the slots on the HMI screen, and tightening the provided
bottom head screws. Follow torque recommendations given in gures. (Figure 3.8 – Figure 3.10)
6. Assembly should resemble Figure 3.11 when completed.
3.2 Install HMI assembly onto ESS Cabinet:
7. Remove SCiB Cover Plate, be sure to retain the washers, locks, and nuts for HMI installation. Bolts remain on
the door. (Figure 3.12–Figure 3.14)
8. Remove protective lm on HMI screen.
9. Mount the HMI assembly onto the door. Ensure HMI connections are located on the bottom for proper
orientation.
10. Secure the assembly to the door by utilizing the washers, locks, and nuts previously removed. Be sure to
follow the drawing attached to this instruction guide. (Figure 3.15 & Figure 3.16)
3.3 Wiring Connections:
11. Refer to wiring schematic (Figure 3.20) to determine wire terminations for following steps.
12. Use 78704 to connect the HMI to the communication port on (90700) board. Follow LED wiring as a guide for
routing and anchoring. (Figure 3.17 & Figure 3.19)
13. Use 78703 to connect HMI for power and ground. Ground conductor will connect to the Door-GND terminal
located at the bottom of the Door by utilizing the NRG M5 Termination. Follow LED Wiring as a guide for
routing and anchoring the power cable to TB4. (Figure 3.18)

3SCiB ESS HMI Installation Insert - 201624-000
FIGURE 3.1: HMI INSTALLATION OVERVIEW

4SCiB ESS HMI Installation Insert - 201624-000
FIGURE 3.2: HMI BRACKET (PN 200866), FRONT VIEW
FIGURE 3.3: HMI BRACKET (PN 200866), BACK VIEW

5SCiB ESS HMI Installation Insert - 201624-000
FIGURE 3.4: HMI SCREEN (200134), FRONT VIEW
FIGURE 3.5: HMI SCREEN (200134), BACK VIEW
FIGURE 3.6: HMI ASSEMBLY, PROPER ORIENTATION

6SCiB ESS HMI Installation Insert - 201624-000
FIGURE 3.7: HMI ASSEMBLY, FRONT VIEW
FIGURE 3.8: HMI MOUNTING CLIPS

7SCiB ESS HMI Installation Insert - 201624-000
FIGURE 3.9: HMI CLIP INSTALLATION VIEW
FIGURE 3.10: SECURING HMI TO BRACKET

8SCiB ESS HMI Installation Insert - 201624-000
FIGURE 3.11: COMPLETED ASSEMBLY
FIGURE 3.12: COVER PLATE FOR REMOVAL, FRONT VIEW
FIGURE 3.13: COVER PLATE REMOVAL, BACK VIEW

9SCiB ESS HMI Installation Insert - 201624-000
FIGURE 3.14: COVER PLATE REMOVED
FIGURE 3.15: HMI ASSEMBLY MOUNTED ON DOOR

10 SCiB ESS HMI Installation Insert - 201624-000
FIGURE 3.16: HMI ASSEMBLY, INSTALLED, FRONT VIEW
FIGURE 3.17: HMI CONNECTION POINT 78704
FIGURE 3.18: 78703 WIREKIT DIAGRAM

11SCiB ESS HMI Installation Insert - 201624-000
FIGURE 3.19: 78704 WIREKIT DIAGRAM

12 SCiB ESS HMI Installation Insert - 201624-000
FIGURE 3.20: HMI WIRING SCHEMATIC

SOCIAL INFRASTRUCTURE SYSTEMS GROUP
POWER ELECTRONICS DIVISION
13131 West Little York Road, Houston, Texas 77041-9990
Tel [phone] Fax. [phone]
US [phone] Canada [phone]
https://www.toshiba.com/tic/industrial/uninterruptible-power-systems
Printed in the U.S.A.