Toshiba 19SLV411U User manual

19SLV411U
24SLV411U
32SLV411U
For an overview of steps for setting up your new TV, see page 11.
Note: To display a High Definition picture, the TV must be
receiving a High Definition signal (such as an over-the-air High
Definition TV broadcast, a High Definition digital cable program,
or a High Definition digital satellite program). For details, please
contact your TV antenna installer, cable provider, or satellite
provider.
© 2011 TOSHIBA CORPORATION
All Rights Reserved
Owner’s Record
The model number and serial number are on
the back of your LCD TV / DVD combination.
Record these numbers in the spaces below.
Refer to these numbers whenever you
communicate with your Toshiba dealer about
this LCD TV / DVD combination.
Model number:
Serial number:
HDA51L1900I

2
Dear Customer,
Thank you for purchasing this Toshiba LCD TV /
DVD combination. This manual will help you use the
many exciting features of your new LCD TV / DVD
combination. Before operating your LCD TV / DVD
combination, please read this manual completely,
and keep it nearby for future reference.
Safety Precautions
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
WARNING
RISK OF ELECTRIC
SHOCK DO NOT OPEN.
WARNING: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING
To prevent injury, this apparatus must be securely
attached to the floor/wall in accordance with the
installation instructions. See item 25 on page 4.
WARNING: If you decide to wall mount this
television, always use a UL Listed wall bracket
appropriate for the size and weight of this television.
The use of any wall bracket other than a UL Listed
wall bracket appropriate for the size and weight of this
television for wall mounting this television could result
in serious bodily injury and/or property damage. See
“Removing the Pedestal Stand” (page 6).
NOTE TO CATV INSTALLERS
This is a reminder to call the CATV system installer’s
attention to Article 820-40 of the U.S. NEC, which
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building,
as close to the point of cable entry as practical. For
additional antenna grounding information, see items
32 and 33 on page 4.
Congratulations on your purchase! As you enjoy your
new product, please keep these safety tips in mind:
The Issue
• The home theater entertainment experience is a growing trend
and larger flat panel displays are popular purchases. However,
flat panel displays are not always supported on the proper stands
or installed according to the manufacturer’s recommendations.
• Flat panel displays that are
inappropriately situated on dressers,
bookcases, shelves, desks,
speakers, chests or carts may fall
over and cause injury.
TOSHIBA Cares!
• The consumer electronics industry
is committed to making home
entertainment enjoyable and safe.
Tune Into Safety
• One size does NOT fit all. Follow the manufacturer’s recommendations
for the safe installation and use of your flat panel display.
• Carefully read and understand all enclosed instructions for
proper use of this product.
• Don’t allow children to climb on or play with furniture and
television sets.
• Don’t place flat panel displays on furniture
that can easily be used as steps, such
as a chest of drawers.
• Remember that children can
become excited while watching a
program, especially on a “larger
than life”flat panel display. Care
should be taken to place or install
the display where it cannot be
pushed, pulled over, or knocked down.
• Care should be taken to route all cords and
cables connected to the flat panel display so that they cannot be
pulled or grabbed by curious children.
Wall Mounting: If you decide to wall mount your
flat panel display, always:
• Use a mount that has been recommended by the display
manufacturer and/or listed by an independent laboratory (such
as UL, CSA, ETL).
• Follow all instructions supplied by the display and wall mount
manufacturers.
• If you have any doubts about your ability to safely install your
flat panel display, contact your retailer about professional
installation.
• Make sure that the wall where you are mounting the display is
appropriate. Some wall mounts are not designed to be mounted
to walls with steel studs or old cinder block construction. If you
are unsure, contact a professional installer.
• A minimum of two people are
required for installation. Flat panel
displays can be heavy.
CHILD SAFETY:
It Makes A Difference How and Where You Use Your Flat
Panel Display

3
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7)
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
or grounding type plug. A polarized
plug has two blades with one wider
than the other. A grounding type
plug has two blades and a third
grounding prong. The wide blade or
the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on
or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
11)
Only use attachments/accessories specified by
the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer,
or sold with the apparatus. When a
cart is used, use caution when moving
the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms
or when unused for long periods of time.
14) Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
Additional Safety Precautions
14a)CAUTION: If the TV is dropped and the cabinet
or enclosure surface has been damaged or the
TV does not operate normally, take the following
precautions:
Wide blade
• ALWAYS turn off the TV and unplug the power
cord to avoid possible electric shock or fire.
• NEVER allow your body to come in contact with
any broken glass or liquid from the damaged
television. The LCD panel inside the TV contains
glass and a toxic liquid. If the liquid comes in
contact with your mouth or eyes, or your skin
is cut by broken glass, rinse the affected area
thoroughly with water and consult your doctor.
• ALWAYS contact a service technician to inspect the
TV any time it has been damaged or dropped.
15) CAUTION:
• To reduce the risk of electric shock, do not
use the polarized plug with an extension cord,
receptacle, or other outlet unless the blades can
be inserted completely to prevent blade exposure.
• To prevent electric shock, match wide blade of plug
to wide slot; fully insert.
16 ) CAUTION:
Do not let children swallow the product or play with
the plastic bag. Keep the product and the plastic bag
out of the reach of children.
17 ) CAUTION :
Do not let water or other liquids come into contact
with the product, as it may result in damage.
18 ) WARNING :
• To prevent the spread of fire, keep candles or other
open flames away from this product at all times.
• Keep the product away from direct sunlight, fire or
a heat source such as a heater. This may reduce
the product lifetime or result in fire.
• The mains plug is used as the disconnect
device, and therefore install the LCD TV / DVD
combination near the wall outlet so that the mains
plug can be accessed easily at all times.
Installation, Care, and Service
Installation
Follow these recommendations and precautions and
heed all warnings when installing your TV:
19) WARNING: NEVER expose batteries to
excessive heat such as sunshine, fire
or the like.
20) ALWAYS plug the product into an outlet that is
located in such a manner that it can be easily
unplugged in case the product requires service.
21) NEVER route the product’s power cord inside a wall
or similar enclosed area.
22)
Never modify this equipment. Changes or
modifications may void: a) the warranty, and b) the
user’s authority to operate this equipment under the
rules of the Federal Communications Commission.
(continued)

4
23) DANGER: RISK OF SERIOUS PERSONAL
INJURY, DEATH, OR EQUIPMENT
DAMAGE!
Never place the TV on an unstable
cart, stand, or table. The TV may
fall, causing serious personal injury,
death, or serious damage to the TV.
24) To avoid damage to this product, never place or
store the TV in direct sunlight; hot, humid areas;
or areas subject to excessive dust or vibration.
25) Always place the TV on the floor or a sturdy, level,
stable surface that can support the weight of the
TV. In order to maintain stability and prevent the TV
falling over, secure the TV with a sturdy strap from
the hook on the rear of the TV pedestal to a wall stud,
pillar, or other immovable structure. Make sure the
strap is tight, secure, and parallel to the floor.
potVTedisVT
4"
min.
Hook
Sturdy strap (as short as possible)
(The sturdy tie and hook is applicable to 32SLV411U.)
26)
The apparatus shall not be exposed to dripping or
splashing, and no objects filled with liquids, such
as vases, shall be placed on the apparatus.
27) Never block or cover the slots or openings in the TV
cabinet back, bottom, and sides. Never place the TV:
• on a bed, sofa, rug, or similar surface;
• too close to drapes, curtains, or walls; or
• in a confined space such as a bookcase, built-in
cabinet, or any other place
with poor ventilation.
The slots and openings are
provided to protect the TV
from overheating and to help
maintain reliable operation
of the TV. Leave a space of at least 4 (four) inches
around the TV.
28)
Always place the back of the television at least 4
(four) inches away from any vertical surface (such
as a wall) to allow proper ventilation.
29) Never allow anything to rest on or roll over the
power cord, and never place the TV where the
power cord is subject to wear or abuse.
30) Never overload wall outlets and extension cords.
31) Always operate this equipment from a 120 VAC,
60 Hz power source only.
32) Always make sure the antenna system is properly
grounded to provide adequate protection against
voltage surges and built-up static charges (see
Section 810 of the National Electric Code).
Antenna lead-in wire
Antenna discharge unit
(NEC Section 810-20)
Grounding conductors
(NEC Section 810-21)
Power service grounding
electrode system
(NEC Article 250 Part-H)
Ground clamp
Electric service
equipment
Ground clamps
33) DANGER: RISK OF SERIOUS
PERSONAL INJURY OR DEATH!
• Use extreme care to make sure you are never in
a position where your body (or any item you are
in contact with, such as a ladder or screwdriver)
can accidentally touch overhead power lines.
Never locate the antenna near overhead power
lines or other electrical circuits.
• Never attempt to install any of the following
during lightning activity: a) an antenna system;
or b) cables, wires, or any home theater
component connected to an antenna or phone
system.
Care
For better performance and safer operation of your
TOSHIBA LCD TV / DVD combination, follow these
recommendations and precautions:
34)
If you use the TV in a room whose temperature is 32 °F
(0 °C) or below, the picture brightness may vary until
the LCD warms up. This is not a sign of malfunction.
35) Always unplug the TV before cleaning. When
cleaning your TV, please first remove any dirt or
dust from the surface. Gently wipe the cabinet
and the display panel surface (the TV screen) with
a dry, soft cloth only (cotton, flannel, etc.). The
enclosed cleaning cloth
is for cabinet cleaning.
Harsh rubbing or use of
a dirty or stiff cloth will
scratch the TV surface.
Avoid contact with
alcohol, thinner, benzene,
acidic or alkaline solvent cleaners, abrasive
cleaners, or chemical cloths, which may damage
the TV surface. Never spray volatile compounds
such as insecticide on the TV surface. Such
products may damage or discolor the TV.
36)
Never hit, press, or place anything on the back cover.
These actions will damage internal parts.
(continued)

5
37) WARNING:
RISK OF ELECTRIC SHOCK!
Never spill liquids or push objects of any kind into
the TV cabinet slots.
38) While it is thundering, do not touch the
connecting cables or apparatus.
39) For added protection of your TV from lightning
and power surges, always unplug the power
cord and disconnect the antenna from the TV if
you leave the TV unattended or unused for long
periods of time.
40) ALWAYS unplug the TV to completely disconnect
from mains power. When the TV is turned off using
the on/off switch, it is not completely disconnected
from power and a minute amount of current is still
consumed.
41) During normal use, the TV may make occasional
snapping or popping sounds. This is normal,
especially when the unit is being turned on or off.
If these sounds become frequent or continuous,
unplug the power cord and contact a Toshiba
Authorized Service Provider.
42) WARNING: RISK OF SERIOUS PERSONAL
INJURY OR EQUIPMENT DAMAGE!
Never strike the
screen with a sharp or heavy
object.
43) • The LCD screen of this product can be damaged by
ultraviolet radiation from the sun. When selecting
a location for the television, avoid locations where
the screen may be exposed to direct sunlight, such
as in front of a window.
• Never touch, press, or place anything on the
LCD screen. These actions will damage the LCD
screen. If you need to clean the LCD screen,
follow the instructions in item 35 on page 4.
Service
44)
WARNING:
RISK OF ELECTRIC SHOCK!
Never attempt to service the TV yourself. Opening
and removing the covers may expose you to
dangerous voltage or other hazards. Failure to follow
this WARNING may result in death or serious injury.
Refer all servicing not specified in this manual to a
Toshiba Authorized Service Provider.
45) If you have the TV serviced:
• Ask the service technician to use only replacement
parts specified by the manufacturer.
• Upon completion of service, ask the service
technician to perform routine safety checks to
determine that the TV is in safe operating condition.
Choosing a location for your LCD
TV / DVD combination
To Display your LCD TV / DVD combination
on the included Pedestal Stand:
Observe the following safety precautions:
1) Read and Follow the pedestal assembly
instructions included with the pedestal.
CAUTION: Before beginning pedestal assembly,
carefully lay the front of the LCD Panel face down
on a flat, cushioned surface such as a quilt or
blanket. Leave the bottom of the unit protruding
over the edge of the surface and assemble the
pedestal as indicated below.
Note: Extreme care should always be used
when attaching the pedestal stand to avoid
damage to the LCD panel.
2) Place the TV on a sturdy, level surface that can
support the weight of the TV.
3) Be sure to secure the TV to a wall, pillar, surface, or
other immovable structure. (item 25,
page 4).
To Display your LCD TV / DVD combination
using a Wall Bracket:
If you decide to wall mount your LCD TV / DVD
combination, always use a UL listed wall bracket
appropriate for the size and weight of the LCD TV /
DVD combination (page 2):
1) CAUTION: Two people are required for installation.
2) Unplug and remove any cables and/or other
component connectors from the rear of the TV.
3) Follow the instructions provided with your wall
bracket. Before proceeding, make sure the
appropriate bracket(s) are attached to the wall and
the back of the TV as described in the instructions
provided with the wall bracket.
4) IMPORTANT: Always use the screws supplied or
recommended by the wall mount manufacturer.
5) After attaching the appropriate bracket(s) to the
wall and the back of the TV, remove the pedestal
stand from the TV as described below.
6)
VESA Mounting Pattern
TV Size Hole Pattern(HxV) Screw Size
19” 100x100 mm M4
24’’100x100 mm M4
32’’200x200 mm M6
(unit in mm)

6
Removing the Pedestal Stand
1) Carefully lay the front of the TV face down on a flat,
cushioned surface such as a quilt or blanket. Leave
the stand protruding over the edge of the surface.
Note: Extreme care should always be used
when removing the pedestal stand to avoid
damage to the LCD panel.
2) Remove the four screws shown in the below diagram.
This will allow removal of the pedestal stand.
3) Once you have removed all four screws, holding
the pedestal stand in place, remove the pedestal
stand from the TV.
CAUTION: Always place the TV on the floor or a
sturdy, level, stable surface that can support the
weight of the unit. To secure the TV, use a sturdy strap
from the hook(s) on the rear of the TV to a wall stud,
pillar, or other immovable structure. Make sure the
strap is tight, secure, and parallel to the floor.
Notes on moisture condensation
Moisture condensation damages the unit. Please
read the following carefully.
Moisture condensation occurs, for example, when
you pour a cold drink into a glass on a warm day and
drops of water form on the outside of the glass. In
the same way, moisture may condense on this unit’s
internal optical pick-up lens, one of the most crucial
internal parts of the unit.
Example of moisture
condensation!
Optical pickup
lens
Moisture condensation may occur in the following
situations:
• When you move the unit from a cold area to a warm
area.
• When you use the unit in a room in which the heat
was just turned on.
• When you use the unit in an area where cold air
from an air conditioner directly hits the unit.
• When you use the unit in a humid area.
It’stoo
warm!
Never use the unit when moisture condensation may
occur.
Using the unit when moisture condensation exists
may damage discs and internal parts. Connect the
power cord of the unit to the wall outlet, turn on the
unit, remove the disc, and leave it for two or three
hours. After two or three hours, the unit will have
warmed up and evaporated any moisture. Leaving
the TV connected to the wall outlet will help prevent
moisture condensation in the unit.
Wall outlet
Wait!
19SLV411U
Four screws
VESA Mounting Pattern
24SLV411U VESA Mounting Pattern
32SLV411U VESA Mounting Pattern
Four screws
Four screws Hook
Sturdy strap
(as short as possible)

7
Notes on discs
On handling discs
• Do not touch the playback side of the disc. Handle
the disc as shown in the figure below.
Playback side
• Do not attach paper or tape to discs.
On cleaning discs
• Fingerprints and dust on the disc cause picture and
sound deterioration. Wipe the disc from the center
outwards with a soft cloth. Always keep the disc
clean.
• Do not use any type of solvent such as thinner,
benzine, commercially available cleaners or antistatic
spray for vinyl LPs. It may damage the disc.
On storing discs
• Do not store discs in a place subject to direct
sunlight or near heat sources.
• Do not store discs in places subject to moisture and
dust such as a bathroom or near a humidifier.
• Store discs vertically in a case. Stacking or placing
objects on discs outside of their case may cause
warping.
Structure of disc contents
Normally, DVD video discs are divided into titles, and
the titles are sub-divided into chapters. Video CDs and
Audio CDs are divided into tracks.
DVD
DVD
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 1 Chapter 2Chapter 3
Video CD/Audio CD
Video CD/Audio CD
Track 1 Track 2 Track 3 Track 4 Track 5
Each title, chapter or track is assigned a number,
which is called “title number”, “chapter number” or
“track number” respectively. There may be discs that
do not have these numbers.
Notes on copyright
The unauthorized recording, use, distribution, or
revision of copyrighted materials including, without
limitation, television programs, videotapes, and DVDs,
is prohibited under the Copyright Laws of the United
States and other countries, and may subject you to
civil and criminal liability.
About this owner’s manual
This owner’s manual explains the basic instructions
of this LCD TV / DVD combination. Some DVD video
discs are produced in a manner that allows specific
or limited operation during playback. As such, the
LCD TV / DVD combination may not respond to all
operating command. This is not a defect of the LCD
TV / DVD combination. Refer to the instruction notes
of discs. The following symbol may appear on the TV
screen during operation.
It means that the operation is not permitted by the
LCD TV / DVD combination or the disc. For example,
sometimes it is unable to stop the playback of
copyright message of the disc when the Stop button
is pressed. Alternatively, this symbol may also indicate
that the feature is not available for the disc.
Notes on region numbers
The region number of this LCD TV / DVD combination
is 1. If region numbers, which stand for their playable
area, are printed on your DVD and you do not find
or , disc playback will not be allowed by the
player. (In this case, the LCD TV / DVD combination
will display a message on-screen.). Some DVDs that
have no region code label may still be subject to area
restrictions and therefore not playable.
On Video CDs
This LCD TV / DVD combination supports Video CDs
equipped with the Playback Control (PBC) function,
version 2.0. You can enjoy two playback variations
depending on types of discs.
• Video CD not equipped with PBC function
(Version 1.1)
Sound and movie can be played on this LCD TV /
DVD combination in the same way as a DVD.
• Video CD equipped with PBC function (Version 2.0)
In addition to operation of a Video CD not equipped
with the PBC function, you can enjoy playback of
interactive software with search function by using
the on-screen playback menu. Some of the functions
described in this owner’s manual may not work with
some discs.

8
Playable discs
This LCD TV / DVD combination can play the following
discs.
Disc
mark Contents Disc size Maximum playback time
DVD
Video
disc
Audio
+
Video
(moving
pictures)
12 cm
Approx. 4 hours
(single sided disc)
Approx. 8 hours
(double sided disc)
8 cm
Approx. 80 minutes
(single sided disc)
Approx. 160 minutes
(double sided disc)
Video
CD
DIGITAL VIDEO
Audio
+
Video
(moving
pictures)
12 cm Approx. 74 minutes
(single sided disc)
8 cm Approx. 20 minutes
(single sided disc)
Audio
CD Audio
12 cm Approx. 74 minutes
(single sided disc)
8 cm Approx. 20 minutes
(single sided disc)
The following discs are also supported.
• DVD-R/RW discs containing files of DVD video format.
• CD-R/CD-RW discs containing CD-DA, Video CD,
MP3, WMA, or JPEG files.
• Kodak Picture CD and FUJICOLOR CD.
Some of these discs may be incompatible.
• You cannot play discs other than those listed above.
• You cannot play discs of DVD-RAM, DVD-ROM,
CD-ROM, Photo CD, etc., or non-standardized discs
even if they may be labeled as above.
• Some CD-R/RWs cannot be played back depending
on the recording conditions.
• This LCD TV / DVD combination uses the NTSC color
system, and cannot play DVD video discs recorded in
any other color system (PAL, SECAM, etc.).
• This LCD TV / DVD combination can play an 8 cm disc.
Please do not use a disc adapter. It may cause trouble.
• Please do not insert any disc of an irregular shape
into the LCD TV / DVD combination, as it may
interfere with the function of the LCD TV / DVD
combination. You may not be able to remove it.
• Please do not use after market accessories, such as
a ring protector, as this may cause trouble with the
operation of the LCD TV / DVD combination.
Because of problems and errors that can occur
during the creation of DVD and CD software and/
or the manufacture of DVD and CD discs, Toshiba
cannot assure that this LCD TV / DVD combination will
successfully play every disc bearing the DVD and CD
logos. If you happen to experience any difficulty playing
a DVD or CD on this LCD TV / DVD combination, please
contact Toshiba Customer Service.
is a trademark of DVD Format / Logo Licensing
Corporation.
FCC Declaration of Conformity
Compliance Statement (Part 15):
The Toshiba 19SLV411U, 24SLV411U and
32SLV411U LCD TV / DVD combinations comply with
Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not
cause harmful interference, and (2) this device must
accept any interference received, including interfer-
ence that may cause undesired operation.
The party responsible for compliance to these rules
is:
Toshiba America Information Systems, Inc.
9740 Irvine Blvd.; Irvine, CA 92618
Ph: 1-800-631-3811
Note: This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by
removing and applying power to the equipment,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and the receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Caution: Changes or modifications to this
equipment not expressly approved by Toshiba
could void the user’s authority to operate this
equipment.

9
ENERGY STAR®User Information
ENERGY STAR User Information Statement: the fac-
tory default settings of this television meet ENERGY
STAR requirements. Changing Picture Settings may
increase energy consumption, possibly beyond the limits
required for ENERGY STAR qualification.
To ensure your television is operating at optimal energy
efficiency, select [Home] mode during initial activation.
To return to [Home] mode settings, select [Standard]
picture mode. [Standard] mode is recommended for
normal home use.(
 page 26)
ENERGY STAR
®
qualified TV.
Products that earn the ENERGY
STAR prevent green house gas
emissions by meeting strict guidelines
set by the U.S. Environmental
Protection Agency. ENERGY STAR
and the ENERGY STAR mark are
registered U.S. marks.
Important notes about your
LCD TV / DVD combination






1) An afterimage (ghost) may appear on the screen if
a fixed, nonmoving image is displayed for a long
period of time. The afterimage is not permanent
and will disappear in a short period of time.
2) The LCD panel contained in this TV is
manufactured using an extremely high level
of precision technology; however, there may
be an occasional pixel (dot of light) that does
not operate properly (does not light, remains
constantly lit, etc.). This is a structural property of
LCD technology, is not a sign of malfunction, and
is not covered under your warranty. Such pixels
are not visible when the picture is viewed from a
normal viewing distance.
Note: Interactive video games that involve
shooting a “gun” type of joystick at an on-
screen target may not work with this TV.
CLASS 1
LASER PRODUCT

The rating sheet and the safety caution are on the rear
of the unit.

























Trademark Information
• Manufactured under license from Dolby
Laboratories.
Dolby and the double-D symbol are
trademarks of Dolby Laboratories.
• HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing
LLC in the United States and other countries.
• MPEG Layer-3 audio coding technology
licensed from Fraunhofer IIS and Thomson.
• This production contains Bitstream Vera Sans
fonts under the following copyright.
Copyright © 2003 by Bitstream, Inc. All
Rights Reserved.
Bitstream Vera is a trademark of Bitstream,
Inc
.

10
Contents
Important Safety Instructions ..........................................3
Installation, Care, and Service ........................................3
Choosing a location for your LCD TV / DVD combination............5
Notes on discs ..................................................................................7
Chapter 1: Introduction ............................................... 11
Features of your new TV................................................................11
Overview of steps for installing, setting up, and using your new TV....11
TV front, top and side panel controls and connections..................12
TV back panel connections ............................................................13
Chapter 2: Connecting your TV ...................................... 14
Overview of cable types.................................................................14
About the connection illustrations .................................................14
Connecting TV to a power source..................................................14
Connecting a VCR, and antenna, Cable TV...................................15
Connecting a camcorder.................................................................15
Connecting a DVD player with ColorStream®(component video)..........16
Connecting a satellite receiver .......................................................16
Connecting an HDMI or DVI device to the HDMI®input.............17
REGZA-LINK®connection ...........................................................18
Connecting a digital audio system .................................................19
Connecting a personal computer (PC) ...........................................20
Chapter 3: Using the remote control................................ 21
Preparing the remote control for use..............................................21
Installing the remote control batteries............................................21
Learning about the remote control .................................................22
Chapter 4: Menu layout and navigation ............................ 24
Main menu layout ..........................................................................24
Setup / Installation menu layout.....................................................25
Navigating the menu system ..........................................................25
Chapter 5: Setting up your TV........................................ 26
Initial Setup ....................................................................................26
Selecting the menu language..........................................................26
Configuring the antenna input source for the ANT/CABLE terminal .........26
Programming channels into the TV’s channel memory.................26
Programming channels automatically ....................................26
Setting channel skip .......................................................................27
Setting the HDMI®audio mode .....................................................28
Viewing the digital signal meter.....................................................29
Setting the time zone......................................................................29
Viewing the system status ..............................................................29
Reset Factory Defaults ........................................................29
Chapter 6: Using the TV’s features.................................. 30
Selecting the video input source to view........................................30
Labeling the video input sources....................................................30
Tuning channels .............................................................................31
Tuning channels using the Channel Browser™...........................31
Setting the Channel Tuning Mode..............................................33
Tuning to the next programmed channel....................................34
Tuning to a specific channel (programmed or unprogrammed).34
Switching between two channels using Channel Return............34
Switching between two channels using SurfLock™...................34
Selecting the picture size................................................................34
Scrolling the TheaterWide®picture (TheaterWide 2 and 3 only)..........36
Using the auto aspect ratio feature .................................................36
Selecting the cinema mode ............................................................37
Using the FREEZE feature.............................................................37
Adjusting the picture ......................................................................37
Selecting the picture mode .........................................................37
Adjusting the picture quality ......................................................38
Using the closed caption mode ......................................................38
Base closed captions...................................................................38
Digital CC Settings ....................................................................39
CC Selector ................................................................................39
Adjusting the audio ........................................................................39
Muting the sound (For TV speakers)..........................................39
Using the digital audio selector..................................................39
Selecting stereo / SAP broadcasts ..............................................40
Using the MTS button ................................................................40
Adjusting the audio quality ........................................................40
Selecting the optical audio output format ..................................40
Using the Dolby®Digital Dynamic Range Control feature .......41
Using the Locks menu....................................................................41
Entering the PIN code ................................................................41
If you cannot remember your PIN code .....................................41
Changing your PIN code ............................................................41
Blocking TV programs and movies by rating (V-Chip) .............41
Downloading an additional rating system for blocking TV
programs and movies......................................................42
Blocking TV programs by Canada rating...................................43
Unlocking programs temporarily ...............................................44
Using the input lock feature .......................................................44
Locking channels........................................................................44
Using the GameTimer®...............................................................44
Using the panel lock feature.......................................................45
Using the PC settings feature .........................................................45
Setting the PC Audio......................................................................45
Using the Media Player..................................................................46
Using the Media Player with USB .............................................46
To select the Auto Start function ................................................46
To open the Media Player ..........................................................46
Viewing photo files ....................................................................47
Single View.................................................................................47
Slide Show..................................................................................47
Playing music files .....................................................................47
During playback .........................................................................48
Viewing photo files with playing music files at the same time..48
Setting the sleep timer....................................................................49
Automatic Power Down .................................................................49
No Signal Power Down..................................................................49
Using REGZA-LINK®...................................................................50
REGZA-LINK®playback device (DVD player, etc.) control ........50
REGZA-LINK®input source selection ......................................50
VOLUME and MUTE controls of Audio Receiver....................51
Other REGZA-LINK®functions................................................51
Displaying TV status information..................................................52
Understanding the auto power off feature......................................52
Understanding the last mode memory feature ...............................52
Chapter 7: Using the TV’s advanced features ..................... 53
Using the advanced picture settings features .................................53
Using Dynamic Contrast ............................................................53
Using the Static Gamma feature.................................................53
Selecting the Color Temperature ................................................53
Using CableClear®digital Noise Reduction...............................54
Using MPEG Noise Reduction ..................................................54
Using the Game Mode feature....................................................54
Chapter 8: Basic disc playback ...................................... 55
Disc playback .................................................................................55
Playback navigation .......................................................................56
Playing in fast reverse or fast forward direction (DVD/VCD/CD)..56
Playing frame by frame (DVD/VCD) ........................................56
Playing in slow motion (DVD/VCD) .........................................56
Locating a chapter or track (DVD/VCD/CD) ............................56
Chapter 9: Advanced disc playback................................. 57
Zoom function/Scene navigation ...................................................57
Using Zoom (DVD/VCD) ..........................................................57
Locating a specific scene ...........................................................57
Scene bookmark .............................................................................58
Bookmarking a scene (DVD/VCD/CD).....................................58
Viewing a scene bookmark (DVD/VCD/CD) ............................58
Repeat playback/A-B repeat ..........................................................58
Enabling repeat playback (DVD/VCD)......................................58
Enabling A-B repeat mode (DVD/VCD/CD).............................59
Programmed playback/Random playback......................................59
Programming the playback sequence (VCD).............................59
Enabling random playback (VCD).............................................60
Scene angle/Title selection/DVD menu .........................................60
Changing the scene angle (DVD)...............................................60
Selecting a DVD title (DVD) .....................................................60
DVD menu (DVD) .....................................................................60
Soundtrack language/Audio channel/Subtitle ................................61
Selecting a soundtrack language (DVD) ....................................61
Selecting the audio channel (VCD)............................................61
Viewing subtitles (DVD) ............................................................61
Playback information/VCD playback control................................61
Viewing the playback info (DVD/VCD) ....................................61
Turning off the PBC function (VCD).........................................61
MP3, WMA, JPEG, and Audio CD operation................................62
MP3/WMA/JPEG/Audio CD information (CD)........................62
About the file browser (CD).......................................................63
Playing an audio file (CD)..........................................................63
Viewing a JPEG file (CD) ..........................................................64
Viewing a slide show (CD).........................................................64
MP3, WMA, JPEG and Audio CD playback modes......................65
Enabling repeat playback (CD) ..................................................65
Enabling random playback (CD)................................................65
Programming the playback sequence (CD)................................66
Chapter 10: Customizing disc playback ............................ 67
Customizing disc playback ............................................................67
Chapter 11: Troubleshooting ......................................... 72
General troubleshooting .................................................................72
LED Indication...............................................................................73
Chapter 12: Appendix ................................................. 74
Specifications .................................................................................74
Acceptable signal formats for PC IN and HDMI terminals...........75
Limited United States Warranty LCD TV/DVD Combination .....76
Limited Canadian Warranty for Toshiba Brand Flat Panel
Televisions..............................................................................77

11
Features of your new TV
The following are just a few of the many exciting
features of your new Toshiba widescreen, integrated
HD, LCD TV / DVD combination:
• Integrated digital tuning (8VSB ATSC and
QAM) eliminates the need for a separate digital
converter set-top box (in most cases).
• 1366 x 768 output resolution. (19SLV411U,
32SLV411U)
• 1920 x 1080 output resolution. (24SLV411U)
• Two HDMI®digital, high-definition multimedia
interfaces 1080p input support (page 17).
• One set of ColorStream®HD high-resolution
component video inputs (page 16).
• Digital Audio Out optical audio connection with
Dolby®Digital optical output format (page 40).
• CableClear®digital picture Noise Reduction
(page 54).
• PC IN (Analog RGB) computer terminal
(page 20).
• REGZA-LINK®allows control of external
devices from the TV remote via HDMI connection
(page 50).
• Media Player allows you to view your JPEG files
and listen to MP3 music. (page 46).
• ENERGY STAR®qualified.
Overview of steps for installing,
setting up, and using your new TV
Follow these steps to set up your TV and begin using
its many exciting features.
1 Carefully read the important safety, installation,
care, and service information. Keep this manual
for future reference.
2 Observe the following when choosing a location
for the TV:
• Read “ Important notes about your LCD TV /
DVD combination ” (page 9).
• Place the TV on the floor or a sturdy, level,
stable surface that can support the weight of the
unit. Secure the TV to a wall, pillar, or other
immovable structure (page 4).
Chapter 1: Introduction
• Place the TV in a location where light does not
reflect on the screen.
• Place the TV far enough from walls and other
objects to allow proper ventilation. Inadequate
ventilation may cause overheating, which will
damage the TV. THIS TYPE OF DAMAGE
IS NOT COVERED UNDER THE TOSHIBA
WARRANTY.
3 Do not plug in any power cords until AFTER you
have connected all cables and devices to your TV.
4 BEFORE connecting cables or devices to the TV,
learn the functions of the TV’s connections and
controls (pages 12–13).
5 Connect your other electronic device(s) to the TV
(pages 14–20).
6 Install the batteries in the remote control
(page 21).
7 See “Learning about the remote control”
(page 22) for an overview of the buttons on the
remote control.
8 AFTER connecting all cables and devices, plug
in the power cords for your TV and other devices.
Then press POWER on the TV control panel or
remote control to turn on the TV. If the TV stops
responding to the controls on the remote control
or TV control panel and you cannot turn the TV
off or on, please unplug the power cords for a few
seconds then re-plug to try again.
9 See “Menu layout and navigation” for a quick
overview of navigating the TV’s menu system
(page 24).
10 Program channels into the TV’s channel memory
(page 26).
11 For details on using the TV’s features, see
Chapters 6 and 7.
12 For details on disc playback, see Chapters 8 and 9.
13 For help, refer to the Troubleshooting Guide,
Chapter 11.
14 For technical specifications and warranty
information, see Chapter 12.
15 Enjoy your new TV!

12
Chapter 1: Introduction
TV front, top and side panel controls and connections
19SLV411U / 24SLV411U / 32SLV411U
4
3
5
6
7
8
9
10
12
9 INPUT / EXIT — Repeatedly press to change the
source you are viewing. When a menu is on-
screen, the INPUT button on the TV’s control
panel functions as the EXIT button.
10 POWER — Press to turn the TV on and off.
If the TV stops responding to the controls on
the remote control or TV control panel and
you cannot turn off the TV, press and hold the
POWER button on the TV control panel for 5 or
more seconds to reset the TV.
Note: 32SLV411U is used for illustration
purposes.
Adjusting the screen angle (Applicable to
19SLV411U/24SLV411U)
You can adjust the angle of the TV screen 3° forward
or 15° backward from a vertical angle. Hold the base
of the TV while adjusting the screen.
Some illustrations in this owner’s manual are
for explanation purposes and may differ from
the actual unit.
1 Power On / Standby LED —
Power LED (Green) = Power indicator
Power LED (Red) = Power standby
2 Remote sensor (embedded) — Point the remote
control toward this remote sensor.
Effective range:
3 Disc slot
— Load the disc, with label facing
forward, into the disc slot to view or listen.
4 EJECT — Press to eject the disc.
5 VOLUME +/- — These buttons adjust the volume
level. When a menu is on-screen, these buttons
function as left/right menu navigation buttons.
6 PLAY X/ CHANNEL S— Press to play the disc
in DVD mode; press to change the channel in
TV mode.
ARROW S— When a menu is on-screen, the
button functions as up menu navigation button.
7 STOP
/ CHANNEL T— Press to stop the disc
playback in DVD mode; press to change the
channel in TV mode.
ARROW T— When a menu is on-screen, the
button functions as down menu navigation
button.
8 MENU (OK) — Press to access the menu system
(page 25). When a menu is on-screen, the
MENU button on the TV’s control panel functions
as the button.
TV frontLeft side panel

13
Chapter 1: Introduction
4 PC IN — For use when connecting a personal
computer.
5 DIGITAL AUDIO OUT — Optical audio output in
Dolby Digital or PCM (Pulse-Code Modulation)
format for connecting an external Dolby Digital
decoder, amplifier, or home theater system with
optical audio input.
6 ANT/CABLE
— Input that supports analog
(NTSC) / digital (ATSC) off-air antenna signals
and analog / digital Cable TV (QAM) signals.
7 HDMI IN
—High-Definition Multimedia
Interface input receives digital audio and
uncompressed digital video from an HDMI
device or uncompressed digital video from a DVI
device. HDMI connection is necessary to receive
1080p signals.
8 USB port
— To access JPEG or MP3 files.
Note: 19SLV411U and 32SLV411U are used for
illustration purposes.
TV back panel connections
For an explanation of cable types and connections see pages 14-20.
1 AUDIO/COLOR STREAM HD — ColorStream®
high-definition component video inputs (with
standard stereo audio inputs) for connecting
devices with component video output, such as a
Toshiba DVD player with ColorStream®.
Note: Component video cables carry only
video information; separate audio cables
are required for a complete connection.
2 AUDIO/VIDEO
— Standard (composite) video and
standard audio inputs (with standard A/V cables)
for connecting devices with composite video.
Note: Standard (composite) video cables
carry only video information; separate
audio cables are required for a complete
connection.
3 PC/HDMI1(Audio) IN — PC audio input terminal
is shared with HDMI 1 analog audio input
terminal, and its use can be configured in the
Audio Setup menu (page 45).
1
2
4
3
5 6
7
8
1
2
4
356
7
8
19SLV411U
32SLV411U (Please use this illustration for 24SLV411U model.)
Power cord
Power cord

14
Overview of cable types
Cables can be purchased from most stores that sell
audio/video devices. Before purchasing any
cables, be sure of connector types required by your
devices and the length of each cable.
Coaxial (F-type) cable
Coaxial (F-type) cable is used for connecting your
antenna, cable TV service, and/or cable converter
box to the
TUNER input on your TV.
Standard A/V cables (red/white/yellow)
Standard A/V cables (composite video) usually come
in sets of three, and are for use with video devices with
analog audio and composite video output. These cables
(and the related inputs on your TV) are typically color-
coded according to use: yellow for video, red for stereo
right audio, and white for stereo left (or mono) audio.
Component video cables (red/green/blue)
Component video cables come in sets of three and are
for use with video devices with component video output.
(ColorStream
®
is Toshiba’s brand of component video.)
These cables are typically color-coded red, green, and
blue. Separate audio cables are required for a complete
connection.
Note: Component video cables provide better
picture performance than a standard (composite)
video.
HDMI®cable (with HDMI Logo “ ”)
HDMI (High-Definition Multimedia Interface) cable is
for use with devices with an HDMI output.
An HDMI cable delivers digital audio and video in its
native format. This cable carries both video and audio
information; therefore, separate audio cables are not
required for a complete HDMI device connection
(page 17, 18 and page 20).
Note: An HDMI cable provides the best audio
and picture performance.
Optical audio cable
Optical audio cable is for connecting receivers with
Dolby Digital or PCM (Pulse-Code Modulation) optical
audio input to the TV’s DIGITAL AUDIO OUT terminal
(page 19).
Analog RGB (15-pin) computer cable
Analog RGB (15-pin) computer cable is for connecting
a PC to the TV’s PC IN terminal (page 20).
Note: Separate audio cables are required for
a complete connection.
3.5mm Stereo to RCA Y-cable
3.5mm Stereo to RCA Y-Cable is for connecting audio
signal from DVI device to TV.
About the connection illustrations
You can connect different types and brands of devices to
your TV in several different configurations. The connection
illustrations in this manual are representative of typical
device connections only. The input/output terminals on
your devices may differ from those illustrated herein. For
details on connecting and using your specific devices, refer
to each device’s owner’s manual.
Connecting TV to a power source
To connect AC power:
120 V, 60 Hz
outlet
AC cord
Note:
•Never connect the AC cord plug to other
than the specified voltage (120 V, 60 Hz).
•If you cause a static discharge when
touching the LCD TV / DVD combination and
it fails to function, simply unplug the LCD TV /
DVD combination from the AC outlet and plug
it back in. The LCD TV / DVD combination
should return to normal operation.
Chapter 2: Connecting your TV

15
Chapter 2: Connecting your TV
Connecting a VCR, and antenna,
Cable TV
wolleY
etihW
deR
wolleY
etihW
deR
You will need:
• coaxial cables
• standard A/V cables
Note: When you use a Cable box, you may not
be able to use the remote control to program or
access certain features on the TV.
To view the antenna or Cable signal:
Select the ANT/CABLE video input source on the TV.*
To view basic and premium Cable channels:
Turn OFF the VCR. Select the ANT/CABLE video
input source on the TV.* Tune the TV to channel 3 or
4 (whichever channel the Cable box output is set to).
Use the Cable box controls to change channels.
To view the VCR:
Turn ON the VCR. Select the VIDEO video input
source on the TV.*
* To select the video input source, press
INPUT
on the
remote control (page 30).
Connecting a camcorder
woll
e
Y
etih
W
deR
wolleY
etihW
deR
You will need:
• standard A/V cables
To view the camcorder video:
Select the VIDEO video input source on the TV.*
* To select the video input source, press
INPUT
on the
remote control (page 30).
The unauthorized recording, use, distribution,
or revision of television programs, videotapes,
DVDs, and other materials is prohibited under
the Copyright Laws of the United States and
other countries, and may subject you to civil and
criminal liability.

16
Chapter 2: Connecting your TV
Connecting a satellite receiver
Red
Green
Blue
Red
White
deR
lBeu
Geern
deR
etihW
You will need:
• standard audio cables
• component video cables
− You can connect the component video
cables (plus audio cables) from the satellite
receiver to the COLOR STREAM HD
terminal on the TV. The COLOR STREAM
HD terminal can be used to display
Progressive (480p, 720p) and Interlaced
(480i, 1080i). Please check the Owner’s
Manual of the satellite receiver in order to
determine the best output signal available.
− If your satellite receiver does not have
component video, connect a standard A/V
cable to AUDIO/VIDEO terminal.
To view satellite programs using the
component video connections:
Turn on the satellite receiver. Select the ColorStream
HD video input source on the TV.*
* To select the video input source, press
INPUT
on the
remote control (page 30).
The unauthorized recording, use, distribution,
or revision of television programs, videotapes,
DVDs, and other materials is prohibited under
the Copyright Laws of the United States and
other countries, and may subject you to civil and
criminal liability.
Connecting a DVD player with
ColorStream®(component video)
deR
Geern
lBeu
Red
White
deR
lBeu
Geern
deR
etihW
You will need:
• standard audio cables
• component video cables
− You can connect the component video
cables (plus audio cables) from the DVD
player to the COLOR STREAM HD terminal
on the TV. The COLOR STREAM HD
terminal can be used to display Progressive
(480p, 720p) and Interlaced (480i, 1080i).
Please check the Owner’s Manual of the
DVD player in order to determine the best
output signal available.
− If your DVD player does not have component
video, connect a standard A/V cable to
AUDIO/VIDEO terminal. If your DVD player
has HDMI video, see page 17.
To view the DVD player:
Turn ON the DVD player. Select the ColorStream
HD video input source on the TV.*
* To select the video input source, press
INPUT
on the
remote control (page 30).

17
Chapter 2: Connecting your TV
To view the HDMI device video:
Select the HDMI 1 or HDMI 2 video input source on the
TV.*
* To select the video input source, press
INPUT
on the
remote control (page 30).
To connect a DVI device, you will need:
• One HDMI-to-DVI adapter cable
− For proper operation, the length of an HDMI-
to-DVI adapter cable should not exceed
9.8 ft (3m). The recommended length is
6.6 ft (2m).
• One 3.5mm Stereo to RCA Y-Cable
− An HDMI-to-DVI adapter cable transfers
video only. Separate analog audio cables
are required (see illustration).
− See “Setting the HDMI
®
audio mode”
(page 28).
deR
etihW
Note: To ensure that the HDMI or DVI device
is reset properly, it is recommended that you
follow these procedures:
•When turning on your electronic components,
turn on the TV first and then the HDMI or
DVI device.
•When turning off your electronic components,
turn off the HDMI or DVI device first and
then the TV.
[1] EIA/CEA-861-D compliance covers the transmission of
uncompressed digital video with high-bandwidth digital
content protection, which is being standardized for
reception of high definition video signals. Because this is
an evolving technology, it is possible that some devices
may not operate properly with the TV.
Connecting an HDMI or DVI
device to the HDMI®input
The HDMI input on your TV receives digital audio
and uncompressed digital video from an HDMI
source device, or uncompressed digital video from
a DVI (Digital Visual Interface) source device.
This input is designed to accept HDCP (High-
Bandwidth Digital-Content Protection) program
material in digital form from EIA/CEA-861-D
compliant[1] consumer electronic devices (such as
a set-top box or DVD player with HDMI or DVI
output). The HDMI input can accept and display
VGA, SVGA, XGA, WXGA, SXGA, 480i (60 Hz),
480p (60 Hz), 720p (60 Hz), 1080i (60 Hz), and
1080p (24 Hz / 30 Hz / 60 Hz) signal formats. For
detailed signal specifications, see page 75. Supported
Audio format: Linear PCM, sampling rate 32/44.1/48
kHz.
Note: To connect a PC to the HDMI input, see
page 20.
To connect an HDMI device, you will need:
• One HDMI cable per HDMI device
− For proper operation, it is recommended that
you use an HDMI cable with the HDMI Logo
( )
− To display a 1080p/60 Hz signal format,
you will need a High Speed HDMI cable.
Conventional HDMI/DVI cable may not work
properly.
− HDMI cable transfers both video and audio.
Separate analog audio cables are not
required (see illustration).
− See “Setting the HDMI
®
audio mode”
(
 page 28).

18
Chapter 2: Connecting your TV
REGZA-LINK®connection
You can control the basic functions of connected audio/video devices using the TV’s remote control if you
connect a REGZA-LINK®compatible audio receiver or playback device. For an explanation of setup and
operations, see pages 50-51.
TV back panel
Audio receiver
Playback device
(REGZA-LINK®DVD player,etc.)
Playback device
(REGZA-LINK®DVD player,etc.)
To connect an Audio Receiver and Playback
Devices, you will need:
• HDMI cables (page 14)
Note:
•If several devices are connected, REGZA-
LINK®feature may not operate properly.
•For proper operation, it is recommended that
you use HDMI cables with the HDMI Logo
( ).
Before controlling the device(s):
• After completing the above connections, set the
REGZA-LINK Setup menu as you desire (page
51).
• The connected devices must also be set. For
details, see the operation manual for each device.
• The REGZA-LINK®feature uses the CEC
technology as regulated by the HDMI standard.
• This feature is limited to models incorporating
Toshiba’s REGZA-LINK®. However, Toshiba is not
liable for those operations. Refer to the individual
instruction manuals for compatibility information.
Note: This feature may not work properly
depending on the devices that are connected.

19
Chapter 2: Connecting your TV
Connecting a digital audio system
The TV’s DIGITAL AUDIO OUT terminal outputs a
Dolby® * Digital or 2-channel down-mixed
PCM (Pulse-Code Modulation) signal for use with
an external Dolby®Digital decoder or other external
audio system with optical audio input.
You will need:
• Optical audio cable (Use an optical audio cable
that has the larger “TosLink” connector and not
the smaller “mini-optical” connector.)
Dolby Digital decoder or
other digital audio system
TV back panel
To control the audio:
1 Turn on the TV and the digital audio device.
2 Press on the remote control and open the
Sound
menu
.
3 Press
S or T to select Audio Setup and then press
.
4
Press Sor Tto select Optical Output Format.
5 Press
W or X to select either Dolby Digital or PCM,
depending on your device.
(
 “Selecting the optical audio output format” on page
40).
6
To save the new settings, highlight Done and then
press .
To revert to the factory defaults, highlight Reset
and then press .
Note:
•Some audio systems may not be compatible
with Dolby Digital bitstream signals. Older
audio systems that are not compatible with
standard optical out signals may not work
properly, creating a high noise level that
may damage speakers or headphones.
THIS DAMAGE IS NOT COVERED BY YOUR
WARRANTY.
•The DIGITAL AUDIO OUT terminal may not
output some digital audio sources because
of copy restrictions.
* Manufactured under license from Dolby
Laboratories. Dolby, and the double-D symbol are
trademarks of Dolby Laboratories.

20
Chapter 2: Connecting your TV
Connecting a personal computer (PC)
With either the PC IN or HDMI connection, you can watch
your computer’s display on the TV and hear the sound
from the TV’s speakers.
To connect a PC to the PC IN terminal on the TV:
When connecting a PC to the PC IN terminal on the TV, use
an analog RGB (15-pin) computer cable and a PC audio cable.
PC audio
cable
PC audio
output
Conversion adapter
(if necessary)
Computer
TV back panel
• To use a PC, set the monitor output resolution on the
PC before connecting it to the TV. The PC IN terminal
can accept and display VGA, SVGA, XGA, and WXGA
signal formats. For detailed signal specifications, see
page 75.
Other formats or non-standard signals will not be
displayed correctly.
• To display the optimum picture, use the PC setting
feature (“Using the PC settings feature” on page 45).
Note:
•The PC audio input terminals on the TV are shared
with the HDMI-1 analog audio input terminals.
•Some PC models cannot be connected to this TV.
•An adapter is not needed for computers with a
compatible mini D-sub15-pin terminal.
•Depending on the DVD’s title and the
specifications of the PC on which you are playing
the DVD-Video, some scenes may be skipped or
you may not be able to pause during multi-angle
scenes.
• Signal names for mini D-sub 15-pin connector
Pin
No.
Signal
name
Pin
No.
Signal
name
Pin
No.
Signal
name
1 R 6 Ground 11 Reserved
2 G 7 Ground 12 SDA
3 B 8 Ground 13 H-sync
4 Reserved 9 5V 14 V-sync
5 Ground 10 Ground 15 SCL
To connect a PC to the HDMI terminal on the TV:
When connecting a PC to the HDMI terminal on the
TV, use an adapter cable and analog audio cables.
If connecting a PC with an HDMI terminal, use
an HDMI cable. Separate analog cables are not
necessary (page 14).
PC audio
output
PC audio
cable
TV back panel
Computer
The HDMI input can accept and display VGA, SVGA,
XGA, WXGA, SXGA, 480i (60Hz), 480p (60Hz), 720p
(60Hz), 1080i (60Hz), and 1080p (24Hz / 60Hz) signal
formats. For detailed signal specifications, see page 75.
Note:
•The edges of the images may be hidden.
•If receiving a 480i (HDMI), 480p (HDMI), 720p,
1080i, or 1080p signal program, Native mode
scales the video to display the entire picture within
the borders of the screen (i.e. no overscanning).