Toshiba 14N21D2 User manual

SERVICE MANUAL
PRINTED IN UK. 2002 C
COLOURTELEVISION
14N21D2
TOSHIBA

C-1
SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter the Service Mode, press both set key and remote control key for more than 2 seconds.
Set Key Remocon Key Operations
VOL. (-) MIN 0 Reset the user setting items (PICTURE, VOLUME and LANGUAGE) to the initial state
for delivery.
VOL. (-) MIN 1
Initialization of the factory.
NOTE: Do not use this for the normal servicing.
If you set a factory initialization, the memories are reset such as the
channel setting, and the POWER ON total hours.
VOL. (-) MIN 6
POWER ON total hours is displayed on the screen.
Refer to the "CONFIRMATION OF HOURS USED".
Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the "WHEN REPLACING EEPROM (MEMORY) IC".
VOL. (-) MIN 8Writing of EEPROM initial data.
NOTE: Do not use this for the normal servicing.
VOL. (-) MIN Display of the Adjustment MENU on the screen.
Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).
9
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to TABLE 1.
WHEN REPLACING EEPROM (MEMORY) IC
Table 1
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
The unit will now have the correct DATA for the new MEMORY IC.
Enter DATA SET mode by setting VOLUME to minimum.
Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds.
ADDRESS and DATA should appear as FIG 1.
ADDRESS is now selected and should "blink". Using the VOL. +/- button on the remote, step through the ADDRESS until
required ADDRESS to be changed is reached.
Press OK to select DATA. When DATA is selected, it will "blink".
Again, step through the DATA using VOL. +/- button until required DATA value has been selected.
Pressing OK will take you back to ADDRESS for further selection if necessary.
Repeat steps 3 to 6 until all data has been checked.
When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
After the data input, set to the initializing of shipping.
Turn POWER on.
Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 2 seconds.
After the finishing of the initializing of shipping, the unit will turn off automatically.
NOTE: No need setting for after INI 16 due to the adjustment value.
CONFIRMATION OF HOURS USED
POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation.
NOTE: If you set a factory initialization, the total hours is reset to "0".
1.
2.
3.
Set the VOLUME to minimum.
Press both VOL. DOWN button on the set and Channel
button (6) on the remote control for more than 2 seconds.
After the confirmation of using hours, turn off the power.
ADDRESS DATA
INIT 01 00
CRT ON 0010
FIG. 1
Initial setting content of MEMORY IC.
POWER ON total hours.
= (16 x 16 x 16 x thousands digit value)
+ (16 x 16 x hundreds digit value)
+ (16 x tens digit value)
+ (ones digit value)
--- 00 00 00 00 60 80 60 68 60
+0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F
INI
10 80 80 80 BC 00 --- --- ---10 00 --- --- --- --- --- ---
00 27 07 83 00 06 00

ELECTRICAL ADJUSTMENTS
D-1
2. BASIC ADJUSTMENTS
2-1: CONSTANT VOLTAGE
1.
2.
3.
4.
Place the set with Aging Test for more than 15 minutes.
Connect the digital voltmeter to TP502.
Set condition is AV MODE without signal.
Adjust the VR501 until the DC voltage is 135 ±0.5V.
1. ADJUSTMENT PROCEDURE
Read and perform these adjustments when repairing the
circuits or replacing electrical parts or PCB assemblies.
CAUTION
•
•
•
•
Use an isolation transformer when performing any
service on this chassis.
Before removing the anode cap, discharge electricity
because it contains high voltage.
When removing a PCB or related component, after
unfastening or changing a wire, be sure to put the wire
back in its original position.
When you exchange IC and Transistor for a heat sink,
apply the silicon grease on the contact section of the
heat sink. Before applying new silicon grease, remove all
the old silicon grease. (Old grease may cause damages
to the IC and Transistor).
1. Oscilloscope
2. Digital Voltmeter
3. Pattern Generator
Prepare the following measurement tools for electrical
adjustments.
2-2: VCO
1.
2.
3.
4.
5.
6.
Place the set with Aging Test for more than 10 minutes.
Connect the oscillator (38.9MHz) to TP003.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (13) on the remote control to
select "VCO COARSE".
Press the VOL. +/- button on the remote control until
the "OK" appear on the screen. If the "OK" is not
displayed, select the "+" side on the changed from "+"
to "-".
Press the Page UP button once to set to "VCO FINE"
mode.
Press the VOL. +/- button on the remote control to
select the 5 step down point from the upper limit on the
"OK".
(Example: In case of the "OK" range 30~41, select 36.)
On-Screen Display Adjustment
1. In the condition of NO indication on the screen.
Press the VOL. DOWN button on the set and the
Channel button (9) on the remote control for more than
2 seconds to appear the adjustment mode on the
screen as shown in Fig. 1-1.
2.
3.
Use the Channel button (0-9) or Channel UP/DOWN
button on the remote control to select the options
shown in Fig. 1-2.
Press the MENU button on the remote control to end
the adjustments.
NO.
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
FUNCTION
CUT OFF
RF AGC
AGC GAIN
R DRIVE
R CUTOFF
G DRIVE
G CUTOFF
B DRIVE
H POSI (50)
V POSI (50)
V POSI (60)
V SIZE (50)
V SIZE (60)
VCO COARSE
VCO FINE
VCO COARSE L1
VCO FINE L1
BRIGHT CENT
BRIGHT MAX
BRIGHT MIN
NO.
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
FUNCTION
TINT
SHARP
CONTRAST CENT
CONTRAST MAX
CONTRAST MIN
COLOR CENT
COLOR MAX
COLOR MIN
M R CUT OFF
M G CUT OFF
M B CUT OFF
CVBS OUT
APR THRESHOLD
BELL FILTER
BANDPASS
H POSI OSD
V POSI OSD
H POSI TEXT
V POSI TEXT
H POSI (60) Fig. 1-2
Fig. 1-1
1.
2.
3.
4.
5.
Place the set with Aging Test for more than 15 minutes.
Receive the UHF (63 ±1dB).
Connect the digital voltmeter to TP002.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (01) on the remote control to
select "RF AGC".
Press the VOL. +/- button on the remote control until the
digital voltmeter is 2.5 ±0.05V.
2-3: AGC VOLTAGE
2-4: CUT OFF
1.
2.
3.
4.
5.
Set condition is AV MODE without signal.
Using the remote control, set the brightness and
contrast to normal position.
Place the set with Aging Test for more than 15 minutes.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (00) on the remote control to
select "CUT OFF".
Adjust the Screen Volume until a dim raster is obtained.
35 H. POSI OSD 128
TV
2-5: WHITE BALANCE
NOTE: Adjust after performing CUT OFF adjustment.
1.
2.
3.
4.
5.
6.
7.
Place the set with Aging Test for more than 10 minutes.
Receive the gray scale pattern from the Pattern
Generator.
Using the remote control, set the brightness and
contrast to normal position.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (03) on the remote control to
select "R DRIVE".
Press the Page UP/DOWN button on the remote control
to select the "R DRIVE", "G DRIVE", "M R CUTOFF" or
"M G CUTOFF".
Adjust the VOL. +/- button on the remote control to
whiten the R DRIVE, G DRIVE, M R CUT OFF, and M G
CUT OFF at each step tone sections equally.
Perform the above adjustments 5 and 6 until the white
color is looked like a white.

ELECTRICAL ADJUSTMENTS
D-2
Receive a 70dB monoscope pattern.
Turn the Focus Volume fully counterclockwise once.
Adjust the Focus Volume until picture is distinct.
2-6: FOCUS
1.
2.
3.
2-7: HORIZONTAL POSITION
1.
2.
3.
4.
5.
6.
7.
8.
Receive the monoscope pattern from the Pattern
Generator.
Using the remote control, set the brightness and
contrast to normal position.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (08) on the remote control to
select "H POSI (50)".
Press the VOL. +/- button on the remote control until
the SHIFT quantity of the OVER SCAN on right and left
becomes minimum.
Receive the monoscope pattern of NTSC. (Audio Video
Input)
Using the remote control, set the brightness and
contrast to normal position.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (39) on the remote control to
select "H POSI (60)".
Press the VOL. +/- button on the remote control until
the SHIFT quantity of the OVER SCAN on right and left
becomes minimum.
Receive the monoscope pattern from the Pattern
Generator.
Using the remote control, set the brightness and
contrast to normal position.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (11) on the remote control to
select "V SIZE (50)".
Adjust by using the VOL. +/- button on the remote
control so that the Up/Down OVER SCAN Quantity
becomes equal to the Right/Left OVER SCAN Quantity.
Receive a broadcast and check if the picture is normal.
Receive the monoscope pattern of NTSC. (Audio Video
Input)
Using the remote control, set the brightness and
contrast to normal position.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (12) on the remote control to
select "V SIZE (60)".
Adjust by using the VOL. +/- button on the remote
control so that the Up/Down OVER SCAN Quantity
becomes equal to the Right/Left OVER SCAN Quantity.
2-8: VERTICAL SIZE
1.
2.
3.
4.
5.
6.
7.
8.
9.
Receive the monoscope pattern from the Pattern
Generator.
Using the remote control, set the brightness and
contrast to normal position.
Adjust the VR401 until the horizontal line becomes fit to
the notch of the shadow mask.
Adjust the VR420 until the SHIFT quantity of the OVER
SCAN on upside and downside becomes minimum.
2-9: VERTICAL POSITION/VERTICAL LINEARITY
1.
2.
3.
4.
2-10: BRIGHT CENT
1.
2.
3.
4.
5.
6
7.
Receive the PAL black pattern*. (RF Input)
Using the remote control, set the brightness and
contrast to normal position.
Place the set with Aging Test for more than 15 minutes.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (17) on the remote control to
select "BRIGHT CENT".
Press the VOL. +/- button on the remote control until
the screen begin to shine.
Receive the PAL black pattern*. (Audio Video Input)
Set to the AV mode. Then perform the above
adjustments 2~5.
*The Black Pattern means the whole black raster signal.
Select the "RASTER" of the pattern generator, set to
the OFF position for each R, G and B.
2-11: CONTRAST CENT
1.
2.
3.
4.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (22) on the remote control to
select "CONTRAST CENT".
Press the VOL. +/- button on the remote control until
the contrast step No. becomes "35".
Receive a broadcast and check if the picture is normal.
Set to the AV mode. Then perform the above
adjustments 1~3.
2-12: COLOR CENT
1.
2.
3.
4.
5.
6.
7.
8.
Receive the PAL color bar pattern. (RF Input)
Using the remote control, set the brightness, contrast
and color to normal position.
Connect the oscilloscope to TP023.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (25) on the remote control to
select "COLOR CENT".
Adjust the VOLTS RANGE VARIABLE knob of the
oscilloscope until the range between white 100% and
0% is set to 5 scales on the screen of the oscilloscope.
Press the VOL. +/- button on the remote control until
the red color level is adjusted to 100 ±10% of the
white level. (Refer to Fig. 2-1)
Receive the PAL color bar pattern. (Audio Video Input)
Set to the AV mode. Then perform the above
adjustments 2~6.
Fig. 2-1
100%

ELECTRICAL ADJUSTMENTS
D-3
2-13: TINT
1.
2.
3.
4.
5.
Receive the NTSC color bar pattern. (Audio Video Input)
Using the remote control, set the brightness and contrast
to normal position.
Connect the oscilloscope to TP024.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (20) on the remote control to
select "TINT".
Press the VOL. +/- button on the remote control until the
section "A" becomes a straight line. (Refer to Fig. 2-2)
Fig. 2-2
"A"
2-14: Confirmation of Fixed Value (Step No.)
Please check if the fixed values of the each adjustment
items are set correctly referring below.
NO.
02
04
06
07
09
10
18
19
20
21
23
24
26
27
30
31
32
33
34
35
36
37
38
FUNCTION
AGC GAIN
R CUTOFF
G CUTOFF
B DRIVE
V POSI (50)
V POSI (60)
BRIGHT MAX
BRIGHT MIN
TINT
SHARP
CONTRAST MAX
CONTRAST MIN
COLOR MAX
COLOR MIN
M B CUT OFF
CVBS OUT
APR THRESHOLD
BELL FILTER
BANDPASS
H POSI OSD
V POSI OSD
H POSI TEXT
V POSI TEXT
RF
00
00
00
45
08
08
30
10
32
02
63
10
45
10
127
31
00
00
00
126
50
122
58
AV
---
---
---
---
---
---
30
10
ADJ.
02
63
10
45
10
---
---
---
---
---
---
---
---
---
*To check for the fixed values of the RF (60Hz), indicate
the adjustment mode screen while input the 60Hz video
signal.

ELECTRICAL ADJUSTMENTS
D-4
3.
1.
2.
3.
1.
2.
3.
4.
5.
6.
7.
8.
3-2: PURITY
NOTE
Adjust after performing adjustments in section 3-1.
1.
2.
3.
4.
5.
Receive the green raster pattern from color bar
generator.
Adjust the pair of purity magnets to center the
color on the screen.
Adjust the pair of purity magnets so the color at the
ends are equally wide.
Move the deflection yoke backward (to neck side)
slowly, and stop it at the position when the whole
screen is green.
Confirm red and blue colors.
Adjust the slant of the deflection yoke while watching the
screen, then tighten the fixing screw.
DEFLECTION YOKE
DEFLECTION YOKE SCREW
MAGNET SCREW
PURITY MAGNETS
6 POLE MAGNETS
4 POLE MAGNETS
Fig. 3-1
PURITY AND CONVERGENCE
ADJUSTMENTS
NOTE
NOTE
3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT)
Tighten the screw for the magnet. Refer to the adjusted
CRT for the position. (Refer to Fig. 3-1)
If the deflection yoke and magnet are in one body,
untighten the screw for the body.
Receive the green raster pattern from the color bar
generator.
Slide the deflection yoke until it touches the funnel
side of the CRT.
Adjust center of screen to green, with red and blue on the
sides, using the pair of purity magnets.
Switch the color bar generator from the green raster
pattern to the crosshatch pattern.
Combine red and blue of the 3 color crosshatch pattern
on the center of the screen by adjusting the pair of
4 pole magnets.
Combine red/blue (magenta) and green by adjusting the
pair of 6 pole magnets.
Adjust the crosshatch pattern to change to white
by repeating steps 6 and 7.
Turn the unit on and let it warm up for at least 30
minutes before performing the following adjustments.
Place the CRT surface facing east or west to reduce the
terrestrial magnetism.
Turn ON the unit and demagnetize with a Degauss Coil.
Adjust after performing adjustments in section 3-2.
3-3: STATIC CONVERGENCE
1.
2.
3.
3-4: DYNAMIC CONVERGENCE
NOTE
Adjust after performing adjustments in section 3-3.
1.
2.
Adjust the differences around the screen by moving
the deflection yoke upward/downward and right/left.
(Refer to Fig. 3-2-a)
Insert three wedges between the deflection yoke and
CRT funnel to fix the deflection yoke.
(Refer to Fig. 3-2-b)
R G B
R
G
B
Fig. 3-2-a
WEDGE WEDGE
WEDGE
WEDGE POSITION
Fig. 3-2-b
R G B
R
G
B
UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT
Receive the crosshatch pattern from the color bar
generator.
Combine red and blue of the 3 color crosshatch pattern
on the center of the screen by adjusting the pair of
4 pole magnets.
Combine red/blue (magenta) and green by adjusting the
pair of 6 pole magnets.

D-5
ELECTRICAL ADJUSTMENTS
4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)
MAIN PCB
CRT PCB
FB401
J701
TP002
TP003
CP101
TU001
CRT
CP401
VR501
VR401
VR420
R527
TP023
CP803A
CD803
CD802
J801
CP806
CP801
CD801
GND CRT
SPEAKER
CP1001
CP502
L503
DEGAUSS
COIL
TP024
AC IN
TP502
CP802A
CD802B
CD803B
R805
R807

BLOCK DIAGRAM
CF202
SAW FILTER
CHROMA IC
IC201 STV2246E
SP1001
SPEAKER
2
3
1
J1001
HEADPHONE_JACK
5
4
1
48
49
VOL UP
CH UP
VOL DOWN
CH DOWN
IC1001 AN7511
SOUND AMP
IC
2
5
8
6
4
OS101
1
56
17OSD_R
16OSD_G
15
OSD_B
20SCL
MICON W/T.TEXT IC
IC101 OECF013A
OSC IN
OSC_OUT
KEY IN
A_MUTE
19SDA
18
OSD_FB
RESET
2
ON_TIMER
49
POWER
10 POWER FAIL
55
REMORT
1
3
40H-SYNC
41V-SYNC
51
50
X101
4 MHz
AGCIF
TU001
11 1
SCL
4
SDA
5
34
35
36
48
47
8
6
7
13
55
18
40
X601
4.433619MHz
52
51
37
20
14
11
30
31
32
Q402
Q401
H. OUTPUT
H. DRIVE
1
19
3
J701
2
MEMORY IC
IC199 S-24C16AFJA-TB-01
SCL
SDA
6
5
Q801
41 3
IC401 TDA8174A
1
RESET IC
IC102 PST3231NR
REG. 9V IC
IC503 KIA78R09API
10
HV
F
S
FB401
FBT
Q803 V801
CRT
397
RGB
Heater F8
4
1
27
25
28
7
16
15
11 20
6
GREEN OUT
BLUE OUT
Q201
VIF PRE. AMP
POWER
Q501
F501
AC IN 3
4
1
2
L501
L503
DEGAUSS COIL
D501~D504
RECTIFIER
T501
5
17
3
8
D101
Q103
LED SW
DY
RF_AGC_OUT
PIFIN2
PIFIN1
OSD_R
OSD_G
OSD_B
OSD_BK
SCL
SDA
CVBSIN2
BLK_EXT
R_EXT/V_EXT
G_EXT/Y_EXT
B_EXT/U_EXT
EXT_AUDIO_IN
R.OUT
H.OUT
G.OUT
B.OUT
VERT
XTAL1
INT_CVBS_OUT
CVBSIN1
FM_OUT
AUDIO_OUT
V-DRIVE IC
Q507
FEED BACK
SWITCHING
Q502
POWER
IC504 LTV-817M-VB
FEED BACK
15
13
1
2
Q802 RED OUT
P.CON SW.
Q510, Q511 42 X1/VAMP/CHR_OUT
10 2
3
7
46BCL/SAF
5
REG. 6V IC
IC502 KIA7806API
1
9
4
Q506
P.FAIL
26
49 LBF/SSC
7
2
1
3
AUDIO SW (MONO) IC
IC703 NJM2233BM-T1
FRONT AUDIO
J703
2
2
FRONT AUDIO
J702
22
Y/CVBS_IN3
42
AV1
Q102
LED SW
E-1 E-2

ABC D E F GH
ABC D E F GH
2
1
3
4
5
6
7
8
2
1
3
4
5
6
7
8
CC001
8990TPA002
:SINCE THESE PARTS MARKED BY
CAUTIONDESCRIBED IN PARTS LIST ONLY
CRITICAL FOR SAFETY,USE ONES ARE
DANS LA NOMENCLATURE DES PIECES
N’UTILISER QUE CELLS DECRITES
DANGEREUSES AN POINT DE VUE SECURITE
:LES PIECES REPAREES PAR UN ETANT
ATTENTION
R139
4.7K
R138
4.7K 1/4W
R116 10K
R124 10K
R152 4.7K
R117
10K
R004
100
R003
100
R151
4.7K
R148
10K
R113
5.6K
R132
150
R126
47
1/4W
R137
270
R121
100
R001
18K 1/2W
R002
18K 1/2W
R006
15K
R005
100K
R125
10K
R133
10K R134
10K
R128
100 1/4W
R129
100 1/4W
R105
10K
R106
10K
R110
5.6K
R140 2.7K
R141 2.7K
R142 2.7K
R143 3.3K
R123
10K
R109 2.2K
R102
820
R103
1.2K
R104
2.2K
R101
390
R120
4.7K
R108
270 1/4W
R111
15K
R107 1K 1/4W R145 1.8K
R146 1.8K
R147 1.5K
R144 1.8K
R135 10K
R112
1.5K
R136
220 1/4W
R115
4.7K
R114
4.7K
C110 0.047 B
C141_1 0.1 F
C139_1
0.47 F
C118_1
0.1 F
C010 0.001 B
C103
22P CH
C109
22P CH
C108
22P CH
C106
0.0022 B
C105
0.1 B
C101
68P CH
C007
0.01 B
C001
0.022 B
C116
0.0047 B
C113
22P CH
C111
0.47 B
C112
82P CH
C120
1B
C104
0.0047 B
C102
0.1 B
C140
220P CH
C119 1B
C006
100P CH
C121
68P CH
C114 0.1 B
W801
TP002
AGC
TP003
VCO
C003_1
150V KA
C122
1016V KA
C131_1
1016V KA
C115 10006.3V YK
D108 1SS133
Q103
2SC2412K
RED LED DRIVE
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
D001 MTZJ33B
D102 MTZJ5.1B
D109
MTZJ5.6B
D107
MTZJ5.6B
C002
4706.3V YK
X101
100CT4R013
4MHz
L001
10uH 0305
L101
10uH 0305
L102
10uH 0305
TU001 TUWRF4EG-778F2A
1
10
11
12 13 14 15
2 3 4 5 6
7
8 9
SW104
EVQ21505R
VOL DOWN
SW103
EVQ21505R
VOL UP
SW102
EVQ21505R
CH DOWN
SW101
EVQ21505R
CH UP
IC199
S-24C16AFJA-TB-01
MEMORY IC
1234
5678
TM101
RC-GX010
BT001
R03(AB)2PXGPI
BT002
R03(AB)2PXGPI
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
CP001
003P-2100
CAUTION: DIGITAL TRANSISTOR
CP101
06JQ-ST
1
2
3
4
5
6
Vout B+ GND
OS101
RPM7138-H5
1 2 3
Q102
KRA102SRTK
GREEN LED DRIVE
IC102 PST3231NR
RESET IC
123
4 5
IC101 OECF013A
MICON W/T.TEXT IC
110111213141516171819 2202122232425262728
29
3
30 31 32 33 34 35 36 37 38 39
4
40 41 42 43 44 45 46 47 48 49
5
50 51 52 53 54 55 56
6
789
ANT001
T4-216AP-BK
G
R
D101_1
LTL-1BEFJ-002A
P.CON+5V
TUNER_BT
P.FAIL
AT+5V_AVDD
AT+5V_DVDD
GND
DEGAUSS
POWER
EMERGENCY
A_MUTE
AV1
PROTECT
IF
RF_AGC
OSD_B
OSD_G
OSD_R
OSD_FB
SCL
SDA
CVBS_TXT
HD
V_OUT
PROTECT
FOR_VCR
3
2
PCB010
TMC571
4.8
4.9 0
4.9
04.9
10
9
8
7
6
5
NC
NC
TEST POINT
NC
NC
IF BTL BPL V.S SDA SCL ADRES AGC
NC
NC
CVBS1
AV2
AV1
V_SYNC
AVDD1
H_SYNC
GND
CVBS2
MCFM
TEST0
AVDD3
VPP
WSCF
JTDO
VDD
SCL
SDA
OSD_FB
OSD_R
OSD_G
OSD_B
STANDBY LED
POWER
I2C_OFF
DEGAUSS
AGND
POWER FAIL
(ATS)
(BBE-H)
PXFM
KEY_IN
TU/RGB
A MUTE
JTCK
JTRSTO
JTMS
CVBSO
AVDD2
OSC_OUT
OSC_IN
RESET
REMORT
TXCF
SECAM_VL_H
H_CONT
ON_TIMER
FORTHD VCR 2
FORTHD VCR 1
EMERGENCY
P4.6/PWM6
PROTECT
STEREO RESET
CSO/RESET0/P3.7
P3.5
P3.4
TUNER HI
0
0
0
0
0
0
0
0
0
0
0
4.8
1.6
4.9
4.9
0
0
2.5
4.9
0
0.2
0.2
0.7
NC
0
4.9
4.9
0
4.8
0.2
1.6
0
0
0
4.9
0
4.9
4.9
4.9
4.9
1.9
2.3
4.8
4.9
4.7
0.6
4.9
2.0
1.6
1.8
NC
4.7
4.9
NC
0.6
2.1
4.9 0 4.9
4
VCC
MODE
SCL SDAVSS
E2 E1 E0
NC
NC
5.0
NC
NC
GND
RESET
VCC
4.9
4.9
0
0
0
NC
NC
RF AGC
I2C OFF
I2C SDA
I2C SCL
GND
1
TO SOUND AMP
FROM/TO POWER
MICON/TUNER SCHEMATIC DIAGRAM
(MAIN PCB)
TO DEFLECTION/CRT
NC
4.6
4.6
4.9 0 4.6 4.6
00 00
ACCESSORY
2.2
NC NC
3.8
NC
4.0
NC
4.9
30.7
NC
0
FROM/TO CHROMA/SIF/VIF/21PIN
G-1
G-2

ABC D E F GH
ABC D E F GH
2
1
3
4
5
6
7
8
2
1
3
4
5
6
7
8
L208
0.39uH
L206
0.39uH
L702
10uH
L203
2.2uH
L204
12uH
L703
10uH
L103
10uH
OUTOUTGININ
CF202_1
G1984M
SAW FILTER
12345
CF201
TPS5.5MB-TF21
CF303
MKT40.4MA110P
CF204
MKT31.9MA110P
B1002
W4BRH3.5X6X1.0
J701
0350_9982_05
21PIN
1
10
11
12
13
14
15
16
17
18
19
220
21 3
4
5
6
7
8
9
L207
3700005
VCO COIL
1 2 34
6
S802XS802Y
C216_1
0.2250V KANP
R216 75 1/4W
R721
150 1/4W
R714
75
R222
75
1/4W
R636
47K
R703
10K 1/4W
R202
270
R218
150
R625
150
R219
1.2K
R204
180
R201
47
R607
22K
R645
2.2K
R638
2.2K
R643
470
R629
270
R628
270
R630
270
R640
27K
R647
560 1/2W
R602
100
R606
100
R646
8.2K 1/4W
R639
5.6K
R706
1K 1/4W
R707
1K 1/4W R715
75 R713
75
R215
6.8K
R213
100 1/2W
R214
2.2K
R208
1K
R217
1K
R601
1.5K
R709
75
R623
1K
R644
2.7K
R203
1K
R621
560 1/4W
R719
100K
R702
820
R622 330K
R708
1K
R720
100 1/4W
R618
10K
R608
47K
R649 22K
C701_2
0.0047 B
C206
1B
C605_1 1F
C213_1
1F
C218
0.022 B
C202
0.001 B
C207
0.33 B
C205
0.001 B
C623
0.1 B
C622
0.1 B
C608
0.1 B
C607
1F
C212
0.01 B
C204
0.022 B
C203
0.022 B
C609
0.1 B
C601
47P CH
C625
47P CH
C612
0.0015 B
C620
0.1 B
C619
0.1 B
C618
0.1 B
C630
0.1 F
C616
0.0047 B
C624
0.01 B
C215
0.1 B
C201
3P CH
C703
470P CH
C221
0.1 B
C621
100P CH
C626
100P CH
C603
1F
C614_1
1F
C615
1B
C610
10016V YK
C611
3.350V KA
C629
1016V KA
C217
4716V YK
C210
150V KA
C602
150V KA
C634
3316V KA
C220 47010V YK
C604
150V KA
C209
1016V KA
C613
47010V YK
D601 1SS133
D602
1SS133
D603
1SS133
D604
11E1-EIC
D605
SB140-EIC
Q201
KTC3881S-RTK
VIF PRE.AMP
Q204
2SC2412K
SIF BUFFER
Q605
2SC2412K
BUFFER
Q202
2SC2412K
BUFFER
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
D709
MTZJ5.1B
D609
MTZJ5.6B
X601
100CT4R408
4.433619MHz
X602
100CT3R509
3.579545MHz
L202
3.3uH 0305
L601
10uH 0305
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
IC201 STV2246E
CHROMA IC
1 101112131415161718192 20 21 22 23 24 25 26 27 28
29
3
30313233343536373839
4
40414243
444546474849
5
50515253545556
6789
P.CON+8V
GND
P.CON+5V
SCART_AUDIO
FRONT_VIDEO_IN
SW_AUDIO_IN
AUDIO_OUT
B.OUT
G.OUT
R.OUT
H_OUT
IF VAMP
ABCL
RF_AGC AFC
SDA V_OUT
SCL
HD
PROTECT
FOR_VCR
V_OUT
CVBS_TXT
OSD_B
OSD_G
OSD_R
OSD_FB
4.4
7.9
5.03.9
11
14
16
17
13
18
12
212019
23
24
FROM/TO MICON/TUNER
NC
NC NC 4.5 2.0 0 3.8 2.4 3.8 3.9 7.8 4.1 0 3.2 2.8 3.2 1.7 3.4 3.6 3.4 02.7 2.8 4.8 3.1 2.7 2.5 2.5
NC
0.2 0 4.1 4.2 4.8 4.5 1.7 1.702.22.42.8
05.0
NC
7.85.44.6 4.42.62.05.24.25.05.04.904.51.5
0.8
7.0
1.5
SIFIN1 SIFIN2
AGCSIFCAP
VREF_IF
AGCPIF_CAP
PIFIN1
PIFIN2
RF_AGC_OUT
IFPLL
GND_IF FM_OUT VCC_IF(5V)
INT_CVBS_OUT EXT_AUDIO_IN
PIF_LC1 PIF_LC2
VCC2(8V)
CVBSIN1
(5V)
SDA SCL SLPF LBF/SSC H_OUT VERT BCL/SAF VCC1 (8V)
NC
GND1 X1/VAMP/CHR_OUT CLPF XTAL1 VCC_D GND_D AUDIO_OUT FM_CAP
BLK_EXT
R_EXT/V_EXT G_EXT/Y_EXT B_EXT/U_EXT
APR CHR
Y/CVBS_IN3
BS
CVBSIN2
GND2
CVBSOUT B.OUT G.OUT R.OUT
ICATH
OSD_B OSD_G OSD_R OSD_BK XTAL3 XTAL2
NC
NC
5.0
3.9
3.2
4.0
2.28
2.9 7.9
FROM/TO DEFLECTION/CRT
FROM POWER
CHROMA/SIF/VIF/21PIN SCHEMATIC DIAGRAM
(MAIN PCB)
1.7
FROM/TO MICON/TUNER
FROM/TO SOUND AMP
PCB010
TMC571
G-3
G-4

ABC D E F GH
ABC D E F GH
2
1
3
4
5
6
7
8
2
1
3
4
5
6
7
8
SPEAKER
SP1001
SA08A05BWC
CP1001
A2502WV2-2P
1
2
:SINCE THESE PARTS MARKED BY
CAUTIONDESCRIBED IN PARTS LIST ONLY
CRITICAL FOR SAFETY,USE ONES ARE
DANS LA NOMENCLATURE DES PIECES
N’UTILISER QUE CELLS DECRITES
DANGEREUSES AN POINT DE VUE SECURITE
:LES PIECES REPAREES PAR UN ETANT
ATTENTION
J1001
MSJ-035-12A_PC
HEADPHONE_JACK
1
2
3
H E
J703
AV1-09D-4
FRONT AUDIO
1 2
H E
J702
AV1-09D-3
FRONT VIDEO
1 2
L704
10uH
B1001
W4BRH3.5X6X1.0
R710
75
R1009
47K 1/4W
R1004
68K
R1010
33 1/2W
R711
820
R740
220
R741
1K
R1011
47K 1/4W
R1006
47K
R1003 100K
C746
0.01 B
C704
0.001 B
C1009
0.0047 B
C1002
47P CH
C1004
0.0015 B
C1003_1
0.150V KA
C711
10010V YK
C1007
1016V KA
C1005_1
0.4750V KA
C745
1016V KA
C744
1016V KA
C1001
47016V YK
C1006
22016V YK
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
L714
10uH 0305
IC703
NJM2233BM-T1
AUDIO SW(MONO) IC
1234
5678
IC1001 AN7511
SOUND AMP IC
1234
5678
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
SW_AUDIO_IN
FRONT_VIDEO_IN
SCART_AUDIO
AUDIO_OUT
P.CON+8V
GND
SOUND+B
AV1
A_MUTE
28
Vin1
SW1
Vin2
NC
Vcc
V.OUT
GND
NC
0 4.4 8.3 0
27
0.35.1 3.9
3.43.58.2 0
0
+-
29
PCB010
SOUND AMP/FRONT AV SCHEMATIC DIAGRAM
(MAIN PCB)
FROM/TO CHROMA/SIF/VIF/21PIN
FROM POWER
FROM DEFRECTION
FROM MICON/TUNER
NC
NC
05.105.1
RED
BLACK
1
2
TMC571
G-5
G-6

ABC D E F GH
ABC D E F GH
2
1
3
4
5
6
7
8
2
1
3
4
5
6
7
8
Q403
KRC102SRTK
PROTEC
HS401
763WSAA013
HS402
763WSA0017
R418_1
6.8 3W
R411_2
150 2W
R424
180 1W
R807
15K 1W
R805
15K 1W
R803
15K 1W
R447
68 1/2W
R429
5.6 1W
B
G
R
11
6
8
10
9
175
V801
A34JXV70X53N45
Q401
TT2140LS-YBC11
H.OUTPUT
CP401
A1561WV2-A5P
1
2
3
4
5
CP801
003P-21001
F
J801
ISMS01S
1
3
4
5
6
7
8
9
CP803B
B2013H02-4P
1
2
3
4
CP803A
B2013H02-4P
1
2
3
4
VR420
470
V_LIN
VR401
2.2K
V_POSI
R417
3.3KM
+-1%
CP806_1
CD801
SM1573-001
GND
E25
E12
8
HEATER
ABL
GND
COL
VIDEO
B+
AFC
GND
HV
F
S
FB401_1 FNI-14B002
1
10
11
2
3
45
6
7
8
9
T401
ETH09K14BZ
1
2
34
6
IC401 TDA8174AV-DRIVE IC
1101123456789
IS NON POLAR ONE.
THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
THE RESISTOR MARKED F IS FUSE RESISTOR.NOTE:
B_SHORT
:SINCE THESE PARTS MARKED BY
CAUTIONDESCRIBED IN PARTS LIST ONLY
CRITICAL FOR SAFETY,USE ONES ARE
DANS LA NOMENCLATURE DES PIECES
N’UTILISER QUE CELLS DECRITES
DANGEREUSES AN POINT DE VUE SECURITE
:LES PIECES REPAREES PAR UN ETANT
ATTENTION
CAUTION: DIGITAL TRANSISTOR
R406
6.8K 1/4W
R405
390K M+-1%
R408
1K 1/4W
R412
8.2K 1/4W
R804
2.7K 1/4W
R802
2.7K 1/4W
R806
2.7K 1/4W
R421
47K 1/4W
R419
1.2K
R416
2.2 1/2W
R811
1.2K 1/4W
R814
1.2K 1/4W
R816
270
R815
270
R809
1.2K 1/4W
R813
270 1/4W
R407
1.2 1/2W
R420
10K 1/4W
R410
680 1/2W
R404
330K M+-1%
R409
680 1/2W
R427
100 1/4W
R446
470 1/2W
R422
1.5K 1/4W
R403
1K 1/2W
R402
1K 1/2W
R445
180K 1/4W
C422
0.22
100V MMTS
C806_1
680P CH
C804
680P B
C437 0.39250V PMS
C412
0.047 MMTV
C805_2
680P CH
C413
0.082 B
C401 220P CH
C819
0.0012KV B
C440
0.01100V MMTS
C443
0.00821.25KV CMPP
C435
0.1100V MMTS
W815
C423
2.2250V MHE
C408
1016V KA
C403
47035V YK
C448
10
250V YK
C414
10035V YK
C446
2250V YK
C404
100010V YK
D809
1SS133
D808
1SS133
D807
1SS133
D403
11E1-EIC
D406
11E1-EIC
D407
11E1-EIC
D410
AU02A-EIC
D405
AU02A-EIC
D404
AU02A-EIC
Q803
KTC3207
BLUE OUT
Q802
KTC3207
RED OUT
Q801
KTC3207
GREEN OUT
Q402
2SC1627_Y
H.DRIVE
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
C417
1050V YK
C418 220025V MHE
L401
4.7mH
0909
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
TP022 TP023 TP024
CP802B
B2013H02-6P
1
2
3
4
5
6
CP802A
B2013H02-6P 1
2
3
4
5
6
R.OUT
G.OUT
B.OUT
VAMP
V_OUT
ABCL
H_OUT
AFC
PROTECT
P.CON+8V
GND
H.DRV+B
+B
SOUND+B
SCREEN
4.9
16.8
6.3
5.6
25.2
413940
35
38
37
36
34
33
NC
NC
DEFLECTION/CRT SCHEMATIC DIAGRAM (MAIN PCB)
(CPJ370BVBK1U-TC)
180V NCNC 180V
NC
POWER OUTPUT OUTPUT STAGE Vs TRIGGER INPUT HEIGHT ADJ. GND Vref. DECOUP. RAMP GENERATOR BUFFER OUTPUT
INVERTING INPUT
Vs FB. GENERATOR
14.5 23.0 5.0 6.4 4.4 12.0 12.0 4.4 25.0 1.70.0 FROM/TO CRT FROM/TO DEFLECTION
PROTECT
0
0
FOCUS
PCB010
HEATER
GND
HEATER GND
B.OUT
G.OUT
R.OUT
B.OUT
R.OUT
G.OUT
CUT OFF
GND
CUT OFF
GND
1
1
(to CP001)
2.7
3.2
95.4
3.2
98.4 2.7
3.2
2.7100.6
FOCUS
ANODE
PCB110
0
0
0
0.3
27.0
FROM/TO CHROMA/SIF/VIF/21PIN
FROM POWER
TO SOUND AMP/FRONT AV
PROTECT
FROM MICOM/TUNER
SCREEN
2.2
0.06
0.0
135
135
131.7
101.6
99.6
0
0
96.4
6.4
130
TMC571
TCC432
G-7
G-8

ABC D E F GH
ABC D E F GH
2
1
3
4
5
6
7
8
2
1
3
4
5
6
7
8
CAUTION
N’UTOLISER QUE DES FUSIBLE DE MEME TYPE
REPLACE ONLY WITH THE SAME TYPE FUSE
:FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,
:POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIE
ATTENTION
IC502 KIA7806API
REG.6V IC
123
Q506
2SA1037AK
P.FAIL
Q504
2SA1624
EMERGENCY
Q511
KTA1281_Y
P.CON SW
IC504
LTV-817M-VB
FEED BACK
1
2 34
F501
50T040H
T4A_L_250V
FH501
EYF-52BC FH502 EYF-52BC
21
L503
8R140018
DEGAUSS COIL
L501
0R7A223F24Y
COIL LINE FILTER
12
34
RY501
ALKS321 12
34T501 8129110H
1
10
11
12
13
14
15
16
17
18
2
3
5
6
7
8
IC503
KIA78R09API
REG.9V IC
1234
TH501
B59104-J80-A10
SW501
ESB92S22B
1
2
34
CP501
A3963WV2-3PD
12
S
DG
Q501
2SK2647-01MR
POWER
21
BLUE
BROWN
CD501_3
1206655819
AC220V_50Hz
L502
W5T29X7.5X19
Q508
KRC111SRTK
EMERGENCY
Q509
KRC111SRTK
EMERGENCY
Q510
KRC103SRTK
P.CON SW
HS501
763WAA0162
HS502
763WAA0186
R502
220 1W
R516
11W
R527
1.2 2W
R503
0.22 1W
VR501
2.2K
+B ADJ R518
4.7K M+-1%
CP502
A1561WV2-2P
1
2
:SINCE THESE PARTS MARKED BY
CAUTIONDESCRIBED IN PARTS LIST ONLY
CRITICAL FOR SAFETY,USE ONES ARE
DANS LA NOMENCLATURE DES PIECES
N’UTILISER QUE CELLS DECRITES
DANGEREUSES AN POINT DE VUE SECURITE
:LES PIECES REPAREES PAR UN ETANT
ATTENTION
B501
W4BRH3.5X6X1.0X2
B504
W5RH3.5X5X1.0
CAUTION: DIGITAL TRANSISTOR
R508 10K
R521
68K
R504
5.6K 1/4W
R519
100
R513
560 1/4W
R514
120K 1/4W
R541
27K
R512
470 1/4W
R520
1.5M 1/4W
R517
1.5M 1/4W
R510
2.2K 1/4W
R522
2.2K
R526
100 1/4W
R507
2.2K
R515
10K
R524
560 1/4W
R532
1K
R511
680 1/4W
R528
10K1/4W
R505
10K 1/4W
R523
220 1/4W
R525
2.2K
1/4W
R501
1.5M 1/2W
R506
22K1/4W
C506_1 0.47 F
C517_1
0.0012KV RR
C532
0.001250V KX
C528
0.0015250V KX
C529
0.01 B
C503
0.0012KV B
C513
0.01 B
C530
0.1 F
C518
0.047 B
C507_1 0.00152KV RR
C509_1
0.0012KV RR
C504
0.0012KV B
C516_1
0.047 MMTV
C524
0.0033 B
C501_2
0.1275V ECQUL
C502_1
0.22275V ECQUL
C527 470P250V KX
C526_1
0.0033 B
W825
C508
10010V YK
C505
82400V USR
C519
150V KA
C514
1016V KA
C533
1016V KA
D505
11E1-B-EIC
D510
RU2AM-EIC
D506
1SS133
D501
RM11C-EIC
D502
RM11C-EIC
D503
RM11C-EIC
D504
RM11C-EIC
D518
1SS133
D513 21DQ09N
D511
1N4937
D514
1SS133
D521
1SS133
D516
21DQ09N
D512 SB140-EIC
D515 SB140-EIC
D509
11E1-EIC
D523
1SS133
D517
11E1-EIC
D507
1SS133
Q507
KTC3198
FEED BACK
SWITCHING
Q502
KTC3203_Y
POWER
Q505
KTC3203_Y
RELAY SW
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
D528
MTZJ5.6B
D508
MTZJ18B
D524
MTZJ3.6B
D525
MTZJ12B
D522
MTZJ18B
C531
2250V YK
C521
100160V YXF
C515
220016V
YK
C522
100016V YK
C525
22016V YK
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME CAUTION: DIGITAL TRANSISTOR
Q512
KRA102SRTK
EMERGENCY
P.CON+8V
GND
GND
P.CON+8V
+B
H.DRV+B
GND
P.CON+5V
P.CON+8V
TUNER_BT
GND
DEGAUSS
P.FAIL
P.CON+5V
AT+5V_DVDD
AT+5V_AVDD
POWER
EMERGENCY
4.9
7.7
7.7
13.0
4A 250V(F501)
4A 250V(F501)
4A 250V
4A 250V
4.9
4.9
4.2
6.7
134.8
NC NC
4.9
4.9
NC
0
0
0
0
0
0
0
5.6
7.7
6.2
4.9
0
0
00
9.1
0.3
12.3
NC
NC
NC
NC
IN
GND OUT
6.008.0 5.0
4.4
0
0.1 4.7
11.2 8.0 0 5.0
0.7
0.1
0.0
PCB010
TO DEFLECTION/CRT
TO SOUND AMP/FRONT AV
TO CHROMA/SIF/VIF/21PIN
FROM/TO MICON/TUNER
5.1
SW
OUT
IN
GND
234.7
0.3
6.7 0.3
0
270
270
9.7
163.9
258.8
237.7
45.9
19.1
POWER SCHEMATIC DIAGRAM
(MAIN PCB)
TMC571
0
BLUE
BROWN
135.0135.0135.0
G-9
G-10

MICON/TUNER
1
CHROMA/SIF/VIF/21PIN
2
3
4
5 10
9
8
7
6 11
The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
NOTE:
0.5µs
1V
10ms
1V
20µs
1V
20µs
1V
50µs
100mV 0.2ms 1V
0.2ms
1V
50µs
0.5V
50µs
100mV
50µs
100mV 20µs 0.5V
12
2ms
200mV
13
20µs
1V
14
20µs
1V
16
20µs
100mV
WAVEFORMS
H-1

WAVEFORMS
The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
NOTE:
17
19
20
20µs
1V
20µs
1V
20µs
1V
23
24
20µs
200mV
10ms
1V
21
20µs
1V
DEFLECTION/CRT
33
34
35
10ms
1V
10ms
10V
10ms
10V
37
20µs
5V
36
20µs
10V
18
20µs
100mV
29
500us
500mV
SOUND AMP/FRONT AV
27
2ms
200mV
28
20µs
1.00V
H-2

WAVEFORMS
The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
NOTE:
38
2µs
200V
39
20µs
50V
40
20µs
50V
41
20µs
50V
H-3

MECHANICAL REPLACEMENT PARTS LIST
Location Part Number Description
101 AE001367 A3M407I720 CABINET,FRONT ASSY
101A AE001368 701UPJA131 CABINET,FRONT
101B AE000389 713UPA0020 GUIDE,REMOCON
101C AE000390 713UPA0021 GLASS,LED
101D AE000391 735UPA0097 BUTTON,BASE
101E AE000865 735UPBA021 BUTTON,FRAME
102 AE001369 A3M407I740 CABINET,BACK ASSY
103 AE000796 752WSAA006 PLATE,SHIELD
104 AE000797 752WSAA008 SHIELD,CASE
105 AE000798 752WSAA013 SHIELD,LID
106 AE001370 722549A187 SHEET,RATING
107 AE000868 735UPB0014 BUTTON,POWER
108 AD300808 735WPA0396 SPEAKER HOLDER
109 BZ710009 741WUA0019 SPRING,EARTH
110 BZ710260 899HV3T000 HOLDER,ANODE WIRE
111 AE001371 800WQ0A002 FELT SHEET
201 BZ710275 8121J50B54 SCREW,TAP TITE(P) GW20 5x28
202 BZ710035 8117540A64 SCREW,TAPPING(B0) TRUSS 4x16
203 BZ710031 8110630A04 SCREW,TAP TITE(P) BRAZIER 3x10
204 BZ710030 8110630804 SCREW,TAP TITE(P) BRAZIER 3x8
205 BZ710019 8109630802 SCREW,TAP TITE(B) BRAZIER 3x8
206 BZ710562 8109I30804 SCREW,TAP TITE(B) WH7 3x8
207 BZ710018 8107630804 SCREW,TAP TITE(S) BRAZIER 3x8
--- AE001372 723000C198 SHEET,BAR CODE
--- AE000093 791WHA0090 LAMIFILM,BAG
--- AE000401 792UHA0165 PACKAGE,TOP
--- AE000402 792UHA0166 PACKAGE,BOTTOM
--- AE001373 793UCDB161 GIFT BOX
--- AE001374 A3M407I975 INSTRUCTION BOOK KIT
--- AE001375 J3M40701A INSTRUCTION BOOK(S)
--- AE001376 J3M40707A QUICK SET-UP SHEET(S)
--- AE001377 J3M40710A INSTRUCTION BOOK(PR)
--- AE001378 J3M40711A INSTRUCTION BOOK(SW)
--- AE001642 J3M40717A REGISTRATION CARD
--- AE001379 J3M40770A QUICK SET-UP SHEET(PR)
--- AE001380 J3M40771A QUICK SET-UP SHEET(SW)
--- AE001672 JB5XD700 POLY,BAG(RED CAUTION)INSTRUCTION
J1-1

ELECTRICAL REPLACEMENT PARTS LIST
Location Part Number Description
RESISTORS
R001 AE000348 R002T2183J RC 18K OHM 1/2W
R002 AE000348 R002T2183J RC 18K OHM 1/2W
R003 AE000965 R903N8101J RC 100 OHM 1/8W
R004 AE000965 R903N8101J RC 100 OHM 1/8W
R005 AE000967 R903N8104J RC 100K OHM 1/8W
R006 AE000970 R903N8153J RC 15K OHM 1/8W
R101 AE000977 R903N8391J RC 390 OHM 1/8W
R102 AE000987 R903N8821J RC 820 OHM 1/8W
R103 AD300658 R903N8122J RC 1.2K OHM 1/8W
R104 AD300655 R903N8222J RC 2.2K OHM 1/8W
R105 AE000966 R903N8103J RC 10K OHM 1/8W
R106 AE000966 R903N8103J RC 10K OHM 1/8W
R107 BZ210119 R002T4102J RC 1K OHM 1/4W
R108 AE000356 R002T4271J RC 270 OHM 1/4W
R109 AD300655 R903N8222J RC 2.2K OHM 1/8W
R110 AE000982 R903N8562J RC 5.6K OHM 1/8W
R111 AE000970 R903N8153J RC 15K OHM 1/8W
R112 AE000969 R903N8152J RC 1.5K OHM 1/8W
R113 AE000982 R903N8562J RC 5.6K OHM 1/8W
R114 AE000979 R903N8472J RC 4.7K OHM 1/8W
R115 AE000979 R903N8472J RC 4.7K OHM 1/8W
R116 AE000966 R903N8103J RC 10K OHM 1/8W
R117 AE000966 R903N8103J RC 10K OHM 1/8W
R120 AE000979 R903N8472J RC 4.7K OHM 1/8W
R121 AE000965 R903N8101J RC 100 OHM 1/8W
R123 AE000966 R903N8103J RC 10K OHM 1/8W
R124 AE000966 R903N8103J RC 10K OHM 1/8W
R125 AE000966 R903N8103J RC 10K OHM 1/8W
R126 AE000486 R002T4470J RC 47 OHM 1/4W
R128 BZ210273 R002T4101J RC 100 OHM 1/4W
R129 BZ210273 R002T4101J RC 100 OHM 1/4W
R132 AE000968 R903N8151J RC 150 OHM 1/8W
R133 AE000966 R903N8103J RC 10K OHM 1/8W
R134 AE000966 R903N8103J RC 10K OHM 1/8W
R135 AE000966 R903N8103J RC 10K OHM 1/8W
R136 BZ210135 R002T4221J RC 220 OHM 1/4W
R137 AE000972 R903N8271J RC 270 OHM 1/8W
R138 BZ210122 R002T4472J RC 4.7K OHM 1/4W
R139 AE000979 R903N8472J RC 4.7K OHM 1/8W
R140 AE000973 R903N8272J RC 2.7K OHM 1/8W
R141 AE000973 R903N8272J RC 2.7K OHM 1/8W
R142 AE000973 R903N8272J RC 2.7K OHM 1/8W
R143 AE000975 R903N8332J RC 3.3K OHM 1/8W
R144 AE001138 R903N8182J RC 1.8K OHM 1/8W
R145 AE001138 R903N8182J RC 1.8K OHM 1/8W
R146 AE001138 R903N8182J RC 1.8K OHM 1/8W
R147 AE000969 R903N8152J RC 1.5K OHM 1/8W
R148 AE000966 R903N8103J RC 10K OHM 1/8W
R151 AE000979 R903N8472J RC 4.7K OHM 1/8W
R152 AE000979 R903N8472J RC 4.7K OHM 1/8W
R201 AE001355 R903N8470J RC 47 OHM 1/8W
R202 AE000972 R903N8271J RC 270 OHM 1/8W
R203 AD300780 R903N8102J RC 1K OHM 1/8W
R204 AE001009 R903N8181J RC 180 OHM 1/8W
R208 AD300780 R903N8102J RC 1K OHM 1/8W
R213 AE000347 R002T2101J RC 100 OHM 1/2W
R214 AD300655 R903N8222J RC 2.2K OHM 1/8W
R215 AE000983 R903N8682J RC 6.8K OHM 1/8W
R216 BZ210107 R002T4750J RC 75 OHM 1/4W
R217 AD300780 R903N8102J RC 1K OHM 1/8W
R218 AE000968 R903N8151J RC 150 OHM 1/8W
R219 AD300658 R903N8122J RC 1.2K OHM 1/8W
R222 BZ210288 R00204750J RC 75 OHM 1/4W
R402 BZ210180 R002T2102J RC 1K OHM 1/2W
R403 BZ210180 R002T2102J RC 1K OHM 1/2W
R404 AE000364 R4X5T6334F R,METAL 330K OHM 1/6W
R405 AE000365 R4X5T6394F R,METAL 390K OHM 1/6W
R406 BZ210162 R002T4682J RC 6.8K OHM 1/4W
R407 AE000349 R002T21R2J RC 1.2 OHM 1/2W
R408 BZ210119 R002T4102J RC 1K OHM 1/4W
R409 AE000354 R002T2681J RC 680 OHM 1/2W
R410 AE000354 R002T2681J RC 680 OHM 1/2W
R411 BZ210229 R3X28A151J R,METAL OXIDE 150 OHM 2W
R412 AE000488 R002T4822J RC 8.2K OHM 1/4W
R416 BZ210053 R002T22R2J RC 2.2 OHM 1/2W
R417 BZ210230 R4X5T6332F R,METAL 3.3K OHM 1/6W
R418 BZ210028 R3X28B6R8J R,METAL OXIDE 6.8 OHM 3W
J2-1

ELECTRICAL REPLACEMENT PARTS LIST
Location Part Number Description
RESISTORS
R419 AD300658 R903N8122J RC 1.2K OHM 1/8W
R420 BZ210182 R002T4103J RC 10K OHM 1/4W
R421 BZ210118 R002T4473J RC 47K OHM 1/4W
R422 AD301301 R002T4152J RC 1.5K OHM 1/4W
! R424 BZ210279 R3X181181J R,METAL OXIDE 180 OHM 1W
R427 BZ210273 R002T4101J RC 100 OHM 1/4W
! R429 AD301761 R635815R6J R,FUSE 5.6 OHM 1W
R445 AE000355 R002T4184J RC 180K OHM 1/4W
R446 AE000353 R002T2471J RC 470 OHM 1/2W
R447 BZ210041 R635U2680J R,FUSE 68 OHM 1/2W
R501 BZ210206 R002T2155J RC 1.5M OHM 1/2W
R502 BZ210240 R3X181221J R,METAL OXIDE 220 OHM 1W
R503 BZ210190 R63581R22J R,FUSE 0.22 OHM 1W
R504 BZ210166 R002T4562J RC 5.6K OHM 1/4W
R505 BZ210182 R002T4103J RC 10K OHM 1/4W
R506 BZ210192 R002T4223J RC 22K OHM 1/4W
R507 AD300655 R903N8222J RC 2.2K OHM 1/8W
R508 AE000966 R903N8103J RC 10K OHM 1/8W
R510 BZ210126 R002T4222J RC 2.2K OHM 1/4W
R511 AE000964 R002T4681J RC 680 OHM 1/4W
R512 AE000358 R002T4471J RC 470 OHM 1/4W
R513 AE000360 R002T4561J RC 560 OHM 1/4W
R514 AE000962 R002T4124J RC 120K OHM 1/4W
R515 AE000966 R903N8103J RC 10K OHM 1/8W
R516 BZ210039 R3X181010J R,METAL OXIDE 1 OHM 1W
! R517 AE000963 R002T4155J RC 1.5M OHM 1/4W
R518 BZ210258 R4X5T6472F R,METAL 4.7K OHM 1/6W
R519 AE000965 R903N8101J RC 100 OHM 1/8W
R520 AE000963 R002T4155J RC 1.5M OHM 1/4W
R521 AE000984 R903N8683J RC 68K OHM 1/8W
R522 AD300655 R903N8222J RC 2.2K OHM 1/8W
R523 BZ210135 R002T4221J RC 220 OHM 1/4W
R524 AE000360 R002T4561J RC 560 OHM 1/4W
R525 BZ210126 R002T4222J RC 2.2K OHM 1/4W
R526 BZ210273 R002T4101J RC 100 OHM 1/4W
R527 BZ210210 R3X28A1R2J R,METAL OXIDE 1.2 OHM 2W
R528 BZ210182 R002T4103J RC 10K OHM 1/4W
R532 AD300780 R903N8102J RC 1K OHM 1/8W
R541 AE000974 R903N8273J RC 27K OHM 1/8W
R601 AE000969 R903N8152J RC 1.5K OHM 1/8W
R602 AE000965 R903N8101J RC 100 OHM 1/8W
R606 AE000965 R903N8101J RC 100 OHM 1/8W
R607 AE000971 R903N8223J RC 22K OHM 1/8W
R608 AE000980 R903N8473J RC 47K OHM 1/8W
R618 AE000966 R903N8103J RC 10K OHM 1/8W
R621 AE000360 R002T4561J RC 560 OHM 1/4W
R622 AE000976 R903N8334J RC 330K OHM 1/8W
R623 AD300780 R903N8102J RC 1K OHM 1/8W
R625 AE000968 R903N8151J RC 150 OHM 1/8W
R628 AE000972 R903N8271J RC 270 OHM 1/8W
R629 AE000972 R903N8271J RC 270 OHM 1/8W
R630 AE000972 R903N8271J RC 270 OHM 1/8W
R636 AE000980 R903N8473J RC 47K OHM 1/8W
R638 AD300655 R903N8222J RC 2.2K OHM 1/8W
R639 AE000982 R903N8562J RC 5.6K OHM 1/8W
R640 AE000974 R903N8273J RC 27K OHM 1/8W
R643 AE000978 R903N8471J RC 470 OHM 1/8W
R644 AE000973 R903N8272J RC 2.7K OHM 1/8W
R645 AD300655 R903N8222J RC 2.2K OHM 1/8W
R646 AE000488 R002T4822J RC 8.2K OHM 1/4W
R647 AE000145 R002T2561J RC 560 OHM 1/2W
R649 AE000971 R903N8223J RC 22K OHM 1/8W
R702 AE000987 R903N8821J RC 820 OHM 1/8W
R703 BZ210182 R002T4103J RC 10K OHM 1/4W
R706 BZ210119 R002T4102J RC 1K OHM 1/4W
R707 BZ210119 R002T4102J RC 1K OHM 1/4W
R708 AD300780 R903N8102J RC 1K OHM 1/8W
R709 AE000985 R903N8750J RC 75 OHM 1/8W
R710 AE000985 R903N8750J RC 75 OHM 1/8W
R711 AE000987 R903N8821J RC 820 OHM 1/8W
R713 AE000985 R903N8750J RC 75 OHM 1/8W
R714 AE000985 R903N8750J RC 75 OHM 1/8W
R715 AE000985 R903N8750J RC 75 OHM 1/8W
R719 AE000967 R903N8104J RC 100K OHM 1/8W
R720 BZ210273 R002T4101J RC 100 OHM 1/4W
R721 AE000937 R002T4151J RC 150 OHM 1/4W
R740 AD301598 R903N8221J RC 220 OHM 1/8W
J2-2

ELECTRICAL REPLACEMENT PARTS LIST
Location Part Number Description
RESISTORS
R741 AD300780 R903N8102J RC 1K OHM 1/8W
R802 BZ210201 R002T4272J RC 2.7K OHM 1/4W
! R803 BZ210099 R3X181153J R,METAL OXIDE 15K OHM 1W
R804 BZ210201 R002T4272J RC 2.7K OHM 1/4W
! R805 BZ210099 R3X181153J R,METAL OXIDE 15K OHM 1W
R806 BZ210201 R002T4272J RC 2.7K OHM 1/4W
! R807 BZ210099 R3X181153J R,METAL OXIDE 15K OHM 1W
R809 BZ210124 R002T4122J RC 1.2K OHM 1/4W
R811 BZ210124 R002T4122J RC 1.2K OHM 1/4W
R813 AE000356 R002T4271J RC 270 OHM 1/4W
R814 BZ210124 R002T4122J RC 1.2K OHM 1/4W
R815 AE000972 R903N8271J RC 270 OHM 1/8W
R816 AE000972 R903N8271J RC 270 OHM 1/8W
R1003 AE000967 R903N8104J RC 100K OHM 1/8W
R1004 AE000984 R903N8683J RC 68K OHM 1/8W
R1006 AE000980 R903N8473J RC 47K OHM 1/8W
R1009 BZ210118 R002T4473J RC 47K OHM 1/4W
R1010 AE000351 R002T2330J RC 33 OHM 1/2W
R1011 BZ210118 R002T4473J RC 47K OHM 1/4W
CAPACITORS
C001 AE000316 CS0RB04H4K CC 0.022 UF 50V B
C002 BZ110189 E02LU0471M CE 470 UF 6.3V
C003 BZ110074 E50HU5010M CE 1 UF 50V
C006 AE000457 CS0RCH412J CC 100 PF 50V CH
C007 AE000312 CS0RB0414K CC 0.01 UF 50V B
C010 AD301466 CHG0B0413J CC 0.001 UF 50V B
C101 AE000326 CS0RCH4U1J CC 68 PF 50V CH
C102 AE000311 CS0RB0315K CC 0.1 UF 25V B
C103 AE000953 CS0KCH4H1J CC 22 PF 50V CH
C104 AE000317 CS0RB04Q3K CC 0.0047UF 50V B
C105 AE000311 CS0RB0315K CC 0.1 UF 25V B
C106 AE000315 CS0RB04H3K CC 0.0022UF 50V B
C108 AE000953 CS0KCH4H1J CC 22 PF 50V CH
C109 AE000953 CS0KCH4H1J CC 22 PF 50V CH
C110 AE000955 CS0RB04Q4K CC 0.047 UF 50V B
C111 AE000310 CS0RB02Q5K CC 0.47 UF 16V B
C112 AE000327 CS0RCH4W1J CC 82 PF 50V CH
C113 AE000953 CS0KCH4H1J CC 22 PF 50V CH
C114 AE000311 CS0RB0315K CC 0.1 UF 25V B
C115 BZ110187 E02LT0102M CE 1000 UF 6.3V
C116 AE000317 CS0RB04Q3K CC 0.0047UF 50V B
C118 BZ110151 CS0RF0415Z CC 0.1 UF 50V F
C119 BZ110278 CS0RB0216K CC 1 UF 16V B
C120 BZ110278 CS0RB0216K CC 1 UF 16V B
C121 AE000326 CS0RCH4U1J CC 68 PF 50V CH
C122 BZ110096 E50HU2100M CE 10 UF 16V
C131 BZ110096 E50HU2100M CE 10 UF 16V
C139 AE000956 CS0RF04Q5Z CC 0.47 UF 50V F
C140 AE000459 CS0RCH4H2J CC 220 PF 50V CH
C141 BZ110151 CS0RF0415Z CC 0.1 UF 50V F
C201 AE000321 CS0RCH430C CC 3 PF 50V CH
C202 AE000229 CS0RB0413K CC 0.001 UF 50V B
C203 AE000316 CS0RB04H4K CC 0.022 UF 50V B
C204 AE000316 CS0RB04H4K CC 0.022 UF 50V B
C205 AE000229 CS0RB0413K CC 0.001 UF 50V B
C206 BZ110278 CS0RB0216K CC 1 UF 16V B
C207 AE000309 CS0RB02L5K CC 0.33 UF 16V B
C209 BZ110096 E50HU2100M CE 10 UF 16V
C210 BZ110074 E50HU5010M CE 1 UF 50V
C212 AE000312 CS0RB0414K CC 0.01 UF 50V B
C213 BZ110162 CS0RF0216Z CC 1 UF 16V F
C215 AE000311 CS0RB0315K CC 0.1 UF 25V B
C216 AE000957 E00NU5R22M CE 0.22 UF 50 V
C217 BZ210177 E02LU2470M CE 47 UF 16V
C218 AE000316 CS0RB04H4K CC 0.022 UF 50V B
C220 BZ110042 E02LU1471M CE 470 UF 10V
C221 AE000311 CS0RB0315K CC 0.1 UF 25V B
C401 AE000600 CQGTCH4H2J CC 220 PF 50V CH
C403 BZ110149 E02LT4471M CE 470 UF 35V
C404 BZ110039 E02LT1102M CE 1000 UF 10V
C408 BZ110096 E50HU2100M CE 10 UF 16V
C412 AE000343 P232T0473J CMPL 0.047 UF 50V MMTV
C413 AE000320 CS0RB04W4K CC 0.082 UF 50V B
C414 AD301434 E02LU4101M CE 100 UF 35V
C417 AD301348 E02LU5100M CE 10 UF 50V
C418 BZ110101 E5EZF3222M CE 2200 UF 25V
C422 AE000961 P232W1224J CMP 0.22 UF 100V MMTS
J2-3