Toshiba 23WL46B User manual

Owners Manual
TOSHIBA
The power to open people’s eyes
23WL46B

- 1 -
Contents
For your safety ........................................ 1
Important Information ............................ 3
Remote Control Buttons ......................... 4
Control Panel Buttons ............................ 5
Preparation ............................................. 6
Before Switchin on your TV ................. 6
Switchin the TV ON/OFF ....................... 7
Operatin the TV ..................................... 8
Menu System .......................................... 9
Sound Menu ....................................... 10
Picture Menu ...................................... 12
Feature Menu ..................................... 14
Installation Menu ................................ 15
Programme Menu .............................. 16
Source Menu ...................................... 18
Other Features ...................................... 18
PC MODE ............................................... 20
Teletext .................................................. 22
Peripheral Equipment Connections .... 24
Antenna Connections ........................... 26
PC INPUT TYPICAL DISPLAY MODES ... 28
Tips ........................................................ 29
Specifications ....................................... 30
For your safety
This e uipment has been designed and
manufactured to meet international safety
standards but, like any electrical e uipment,
care must be taken if you are to obtain the
best results and safety is to be assured. So,
please read the points below for your own
safety. They are of a general nature, in-
tended to help you with all your electronic
consumer products and some points may
not apply to the goods you have just pur-
chased.
Some DOs and DONTs for you
Air Circulation
Leave at least 10cm clearance around the
television to allow ade uate ventilation. This
will prevent the TV from overheating and
conse uential possible damage to the TV.
Dusty places should also be avoided.
Heat Dama e
Damage may occur if you leave the TV in di-
rect sunlight or near a heater. Avoid places
subject to extremely high temperatures or
humidity, or locations where the temperature
is likely to fall below 5ºC (41ºF).
Mains Supply
The mains supply re uired for this e uip-
ment is 230V AC, 50 Hz. Never connect to a
DC supply or any other power source. DO
ensure that the TV is not standing on the
mains lead. DO NOT cut off the mains plug
from this e uipment, this incorporates a
special Radio Interference Filter, the re-
moval of which will impair its performance.
Mains fuse should be 13A.
Hot / Moderate Climate Conditions
This device is suitable for working in hot and
moderate climate conditions.
IF IN DOUBT PLEASE CONSULT A
COMPETENT ELECTRICIAN.
DO
DO read the operating instructions before
you attempt to use the e uipment.
DO ensure that all electrical connections (in-
cluding the mains plug, extension leads and
inter-connections between pieces of e uip-
ment) are properly made and in accordance
with the manufacturers instructions.
2309W-ENG-1550UK (TOSHIBA UK)-17 INCH TFT.p65 13.05.2004, 18:551

- 2 -
Switch off and withdraw the mains plug be-
fore making or changing connections.
DO consult your dealer if you are ever in
doubt about the installation, operation or
safety of your e uipment.
DO be careful with glass panels or doors on
e uipment.
DO NOT
DONT remove any fixed cover as this may
expose dangerous voltages.
DONT obstruct the ventilation openings of
the e uipment with items such as newspa-
pers, table-cloths,
curtains etc. Overheating will cause damage
and shorten the life of the e uipment.
DONT allow electrical e uipment to be ex-
posed to dripping or splashing or objects
filled with li uids, such as vases, to be
placed on the e uipment.
DONT place hot objects or naked flame
sources, such as lighted candles or night-
lights on, or close to the e uipment. High
temperatures can melt plastic and lead to
fires.
DONT use makeshift stands and NEVER fix
legs with wood screws. To ensure complete
safety, always fit the manufacturers ap-
proved stand or legs with the fixings pro-
vided according to the instructions.
DONT listen to headphones at high volume,
as such use can permanently damage your
hearing.
DONT leave e uipment switched on when it
is unattended, unless it is specifically stated
that it is designed for unattended operation
or has a standby mode. Switch off using the
switch on the e uipment and make sure
your family know how to do this. Special ar-
rangements may need to be made for infirm
or handicapped people.
DONT continue to operate the e uipment if
you are in any doubt about it working nor-
mally, or it is damaged in any way  switch
off, withdraw the mains plug and consult
your dealer.
DONT put the empty batteries into garbage
instead of recycle bin to reduce harmfull ef-
fects to the environment.
ABOVE ALL  NEVER let anyone, especially
children, push anythin into holes, slots or
any other openin s in the case  this could
result in a fatal electric shock.
NEVER guess or take chances with electri-
cal e uipment of any kind  it is better to be
safe than sorry.
To fully disconnect the TV, switch off the
mains socket and remove the Power plu .
Safety Precautions for Power adapter
 Be careful! May become hot.
 For indoor and dry location use only.
 Risk of electric shock.
 Shock hazard, do not open.
 Keep all power adapters away from any
other heat source.
 Always use power adapter(s) well-ventilated
area.
** Cold cathode fluoresant lamp in LCD
PANEL contains a small amount of mer-
cury, please follow local ordinates or regula-
tions for disposal.
"The LCD panel is very hi h technolo y
product with about a million thin film tran-
sistors, ivin you fine picture details. Oc-
casionally, a few non-active pixels may ap-
pear on the screen as a fixed point of blue,
reen or red. Please note that this does
not affect the performance of your prod-
uct." Please note that certain li ht uns
used with ames consoles may not work
on this product.
2309W-ENG-1550UK (TOSHIBA UK)-17 INCH TFT.p65 13.05.2004, 18:552

- 3 -
Important Information
Please take note
EXCLUSION CLAUSE
Toshiba shall under no circumstances be liable for loss and/or damage to the product
caused by:
 fire;
 earth uake;
 accidental damage;
 intentional misuse of the product;
 use of the product in improper conditions;
 loss and/or damage caused to the product whilst in the possession of a third party;
 any damage or loss caused as a result of the owner s failure and/or neglect to follow the
instructions set out in the owners manual;
 any loss or damage caused directly as a result of misuse or malfunction of the product
when used simultaneously with associated e uipment;
Furthermore, under no circumstances shall Toshiba be liable for any conse uential
loss and/or damage including but not limited to the following, loss of profit, interruption
of business, the loss of recorded data whether caused during normal operation or
misuse of the product.
WARNING! NE ER LEA E A
STATIONARY IMAGE ON THE
SCREEN
If stationary images generated by TELE-
TEXT, CHANNEL IDENTIFICATION LOGOS,
COMPUTER DISPLAYS, VIDEO GAMES,
ON SCREEN MENUS, etc. are left on the TV
screen for any length of time, they could be-
come permanently ingrained.
If you use your television to display com-
pletely still images, or moving pictures
which have a permanent still image super-
imposed e.g. broadcast network logos, it is
always advisable to reduce BOTH the
brightness and contrast settings.
Care and disposal
Cleanin the screen and cabinet...
Turn off the power, clean the screen and
cabinet with a soft, dry cloth. We recom-
mend that you do not use any proprietary
polishes or solvents on the screen or cabi-
net as this may cause damage.
Disposal...
When the set reaches the end of its useful
life please dispose of it in accordance with
Local Government Regulations or at a recy-
cling centre.
2309W-ENG-1550UK (TOSHIBA UK)-17 INCH TFT.p65 13.05.2004, 18:553

- 4 -
Remote Control Buttons
= Stand By
= Cursor Up
= Cursor Right
OK = Okey (Store)
= Info (Program Menu)
0 - 9 = Direct Program
-/-- = Double Digit
=Previous Programme
P/CH + = Programme Up
+ = Volume +
= TV / Quit Menu
(;7
= External Source
(AV-1, AV-2, AV-3, S-VIDEO, PC)
Yellow (FEATURE) = Feature Menu
Blue (INSTALL) = Installation Menu
= Hold
= Update, = PC and Picture
= Index Page
= Reveal, PC = Switch from TV to PC
= Expand, = Aspect ratio
= Mix, = PIP on / PIP off
= Teletext
= Time
Red (SOUND) = Sound Menu
Green (PICTURE) = Picture Menu
= Mute
I-II = Mono/Stereo - Dual I-II
- = Volume -
- P/CH = Programme Down
= Personal Preference
M = Menu

= Cursor Down

= Cursor Left





,
02.


































2309W-ENG-1550UK (TOSHIBA UK)-17 INCH TFT.p65 13.05.2004, 18:554

- 5 -
Control Panel Buttons
92/80(
3&+
0(18
67$1'%<
/('
,1)5$5('5(&(,9(5
63($.(5 63($.(5
79$9
With certain combinations of connectors and leads the back cover
may not be easily fitted. If the cover is left off, this in no way infringes
safety re uirements.
)227723&29(5
2309W-ENG-1550UK (TOSHIBA UK)-17 INCH TFT.p65 13.05.2004, 18:555

- 6 -
Preparation
Install Display on solid horizontal surface
such as a table or desk.
For ventilation, leave a space of at least 10
cm free all around the set. To prevent any
fault and unsafe situations, please do not
place any objects on top of the set.
This apparatus can be used in tropical and/
or moderate climates.
Features
 It is a remote controlled colour television
and PC monitor.
 100 programmes from VHF, UHF bands or
cable channels can be preset.
 It can tune cable channels.
 Controlling the TV is very easy by its menu
driven system.
 It has 2 pieces of Euroconnector socket for
external devices (such as video, video
games, audio set, etc.)
 To use as a monitor, 15 Pin Mini D-Sub con-
nector for computer.
 Stereo sound system (German+Nicam) is
available.
 Multilanguage OSD.
 Teletext (Fastext (7 pages), Toptext).
 It is possible to connect headphone.
 A.P.S. (Automatic programming system)
 All programmes can be named.
 Programme swapping between last
watched two programmes.
 Forward or backward automatic tuning.
 Sleep timer.
 Child lock
 Auto, 4:3, 16:9, Cinema, Subtitle, Zoom and
Panorama modes.
 Automatic sound mute when no transmis-
sion.
 When no valid signal is detected, after 5
minutes the TV switches itself automatically
to stand-by mode.
 NTSC Playback.
 Universal power supply range is a standard
feature on this model.
 TV Picture in PC (if PC input available).
 TV Picture and PC
 PLL (Channel Search)
 PC input (Support Up to 1280 x 768)
Panel Features
 High resolution (1280x768) 23" TFT LCD
display
 High contrast ratio (400:1 typical)
 Brightness: 450 cd/m2 (typical).
 High-speed response time: 21 ms (typical)
 Wide viewing angle (typical)176° (horizontal)
and 176° (vertical)
 8-bit colour depth, display 16.7 M colours.
Before Switching on your TV
Power connection
Only use the adaptor supplied with this
product.
$&DGDSWHU
7R32:(5
,1387'&9
WHUPLQDO
IMPORTANT: The TV set is designed to op-
erate on 24 V DC. For this, an adaptor is
used which ives 24V DC volta e. Connect
this adaptor to a system that supplies
230V AC, 50 Hz.
 After unpacking, allow the TV set to reach the
ambient room temperature before you con-
nect the set to the mains.
2309W-ENG-1550UK (TOSHIBA UK)-17 INCH TFT.p65 13.05.2004, 18:556

- 7 -
Connections to the RF input
socket
9+) 8+)
 :
795($53$1(/
&$%/(79
 Connect the aerial or cable TV plug to the
RF input socket located at the back of the TV
and connect the cable plug coming out from
the TV out socket located at the devices
(VCR, DVB etc.) to this socket as well.
How to connect other devices
IMPORTANT: Switch off the TV before con-
necting any external device.
Sockets for external connections are at the
back of the TV. For connection of other de-
vices via Euroconnector refer to the manuals
of the related devices.
Inserting batteries in the remote
control handset
 Remove the battery cover located on the
back of the handset by gently pulling up-
wards from the indicated part.
 Insert two AAA (R03)/UM4 or e uivalent type
of batteries inside.
 Replace the battery cover.
NOTE: Remove the batteries from remote
control handset when it is not to be used for
a long period.Otherwise it can be damaged
due to any leakage of battery.
Old batteries must be disposed in a desig-
nated area. If performance of the remote
control reduces, replace the batteries with
the correct type. Do not combine a used, old
battery or a new one or mixed battery types.
Remove dead batteries immediately to pre-
vent acid from leaking into the battery com-
partment.
Switching the TV ON/OFF
To switch the T on
Your TV will switch on in two steps:
1- Connect the power supply cord to the sys-
tem. Press the   button on the right side
of the TV. Then the TV switches itself to
stand-by mode and the led becomes sap-
phire blue located on the front of the TV.
2- To switch on the TV from stand-by mode
either:
Press the   button on the remote control,
or,
Press a digit button on the remote control so
that a programme number is selected,
or,
Press P/Ch button on the right side of the
TV or press -P/CH or P/CH+ buttons on
the remote control, so that last switched off
programme is selected.
By either ways the TV will switch on and di-
minishes the brightness of the led.
To switch the T off
NOTE: To switch the TV off completely re-
move the mains plug from the socket.
 Press the   button on the remote control,
so the TV will switch to stand-by mode and
the LED will become sapphire blue.
or,
2309W-ENG-1550UK (TOSHIBA UK)-17 INCH TFT.p65 13.05.2004, 18:557

- 8 -
Press the   button located on the right
side of the TV, so the TV will switch off and
the BLUE LED will turn off.
Operating the TV
You can operate your TV both using the
remote control handset and onset buttons.
A.P.S. (Automatic Programming
System)
"All Prestored Pro rammes Will Be
Erased" message will be displayed when
you turn your TV on for the first time. APS,
searches and sorts all channels and stores
them automatically on your TV, according to
the transmission of programme systems in
your area.
To cancel APS before starting, press  
button. First of all choose the Country.
This, will effect the sort process in APS. By
pressing the   or   button, come to the
"Lan ua e" item and select the language in
which the menus of the TV will appear. As
soon as you change the language, the
menu items will be displayed in the selected
language. To select Continue use
 or   button and press   or   but-
ton.
:DUQ LQJ
&RXQWU\
/DQJXDJH
&RQWLQXH
&DQFHO
$OO3UHVWRUHG3URJUDPPHV
:LOO%H(UDVHG
$36,V5XQQLQJ
3OHDVH:DLW
After APS is finalized, a programme list will
apper on the screen. In the programme list
you will see the programme numbers and
names assigned to the programmes.
If you press the   button at any time while
the A.P.S. is running, the A.P.S. will be
ended. Then, the program list on the screen
will show channels captured until this time.
If you do not accept the locations and / or the
programme names of programmes, you
can change them in Programme menu.
Operating with the buttons on the
T set
Volume setting and programme selection
can be made by using the buttons at the
control panel on the right side of the TV.
Volume Settin
 Press   button to decrease volume or
 button to increase volume, so a volume
level scale (slider) will be displayed at the
middle of the bottom on the screen.
Pro ramme Selectin
 Press   button to select the next pro-
gramme or   button to select the previ-
ous programme.
Enterin Main Menu
 Press "MENU" button to enter Main menu. In
the Main menu select submenu using
 or   button and enter the sub-menu
using   or   button. To learn the us-
age of the menus, refer to the Menu System
section.
Operating with Remote Control
The remote control handset of your TV is de-
signed to control all the functions of the
model you selected. The functions will be
described in accordance with the menu sys-
tem of your TV.
Functions of the menu system are de-
scribed in Menu System section.
Volume Settin
Press  + button to increase volume.
Press -  button to decrease volume. A
volume level scale (slider) will be displayed
at the middle of the bottom on the screen.
2309W-ENG-1550UK (TOSHIBA UK)-17 INCH TFT.p65 13.05.2004, 18:558

- 9 -
,,

,


Pro ramme Selectin
(Previous or next programme)
 Press -P/CH button to select the previous
programme.
 Press P/CH+ button to select the next pro-
gramme.
Pro ramme Selectin (direct access):
Press digit buttons on the remote control
handset to select programmes between 0
and 9. TV will switch to the selected pro-
gramme. To select programmes between
10 - 99, you must use the double digit button
"- / - -".
3
this OSD is displayed at the left
hand upper on the screen.
After then, press the digit buttons consecu-
tively which programme you want to select
(eg. for programme 27, first press 2 and
then 7). When it is late to press any digit but-
ton this function will be ignored and the dis-
play will be erased. In the same way it must
not be late to press any digit button after en-
tering the first digit. The limit of the delay
time is 3 seconds.
Press directly the programme number to
reselect single digit programmes.
Pro ramme Swappin
 Press "P<P" (programme swap) button to
select the last selected programme. This
button provides swapping between last two
selected programmes. For example, select
programme 8, then select programme 2.
Now, if you press "P<P" button, programme
8 will be selected. If you press the same
button again, programme 2 will be selected
and so on.





Menu System
Your TV has been designed with a menu
system to provide an easy manipulation of a
multi-function system. The TV is controlled
by choosing the commands, which are dis-
played on the screen.
Press the "M" button. The main menu will be
displayed in the middle of the screen.
0HQX
To select a sub-menu use   or   button,
and press   or   button or directly press
OK button.
MAIN MENU
The menu system is described below.
The short way in order to enter the menus,
press :
"M" Button, Main Menu.
Red Button, Sound Menu.
Green Button, Picture Menu.
Yellow Button, Feature Menu.
Blue Button, Install Menu.
"" Button, Pro ramme Menu in TV
mode or,
Source Menu In AV mode
Menu button has two functions; first is open-
ing or closing the main menu, and the sec-
ond is closing the sub-menu and then open-
ing its parent menu.
2309W-ENG-1550UK (TOSHIBA UK)-17 INCH TFT.p65 13.05.2004, 18:559

- 10 -
Menu does not disappear automatically if it
is left on the screen.
Press   key on the remote control unit to
remove menu.
Sound Menu
To chan e sound settin s
 Enter the Sound Menu directly by pressing
the Red button or,
 As you enter the main menu, sound will be
the first item. In the main menu, select
Sound using   or   button, then enter
the sound menu pressing   ,   or
OK button.
Settin Volume:
As you enter the sound menu, Volume will
be the first selected option.
 Press   button to increase volume.
 Press   button to decrease volume.
Or you can directly change the volume set-
tings using  + (to increase) or
-  (to decrease) button.
6RXQG
Settin Balance
It allows adjusting the distribution between
the left and right speakers.
 Using   or   button select Balance.
 Press   button to change balance right-
ward.
 Press   button to change balance left-
ward.
When balance control is in mid position, the
cursor is displayed with one arrow.
6RXQG
Selectin Mode
 Using   or   button select Mode.
 Press   or   button to change Mode.
You can choose Mono, Stereo or Dual
(I-II) mode, only if the selected channel sup-
ports that mode.
You can also change sound mode directly
pressing I-II button on your remote control.
6RXQG
0RQR
In case of bilingual broadcast (Dual Sound),
you can select original or dubbed language
using mode option.
Settin Effect
You can use this feature to switch the sound
effect on and off. Pressing   or   button
will turn on and off this feature. If the current
sound system is Mono and the sound effect
is set ON, then the sound will be heard as if
it is Stereo. If the current sound system is
Stereo, switching this effect on will make the
sound deeper. Switching it off will make no
change in Mono and Stereo.
2309W-ENG-1550UK (TOSHIBA UK)-17 INCH TFT.p65 13.05.2004, 18:5510

- 11 -
6RXQG
2Q
To Chan e H.Phone/Line Out Settin s
 Using   or   button select H.Phone/
Line Out.
 Press   or   button or directly press
OK button on H.Phone/Line Out, to enter
the H.Phone/Line Out menu. This is a sub-
menu of Sound menu, and all options in
this menu are working as the same in the
Sound menu.
6RXQG
Settin H.Phone/Line Out Volume
 As you enter the H.Phone/Line Out sound
menu, Volume will be the first selected op-
tion.
 Press   button to increase volume.
 Press   button to decrease volume.
+3KRQH/LQH2XW
Settin H.Phone/Line Out Sound Mode
 Using   or   button select Sound Mode.
Pressing   or   button will change the
current sound mode. (e.g.: If the current
sound mode is stereo, it will be stereo or
visa versa).
In case of bilingual broadcast, you can se-
lect original or dubbed language again us-
ing mode menu. So when somebody lis-
tens to the original language from the loud-
speakers, somebody else can listen to the
dubbed language from headphone.
To Store the Settin s
 Press OK button on the remote control to
store the settings directly.
or,
 Using   or   button select Store. Press
,   or OK button to store current
H.Phone/Line Out volume and sound
mode. The stored values will be valid for all
the programmes.
Equalizer
 Using   or   button select E ualizer.
 Press   or   button or directly press
OK button to enter E ualizer sub-menu.
6RXQG
(TXDOL]HU
In Mode item there are five predefined and
one user defined options. These are User,
Classic, Jazz, Rock, Pop and Flat. The pre-
defined options can not be changed by the
user. If you want to change one of the fre-
uency values of the predefined options, the
2309W-ENG-1550UK (TOSHIBA UK)-17 INCH TFT.p65 13.05.2004, 18:5511

- 12 -
Mode must be switched to User option.
The 5 items below the Mode are available to
adjust the sound settings in
5 fre uency values: 120 Hz, 500 Hz, 1.5 kHz,
5 kHz and 10 kHz. To change the values of
5 fre uency options, select one of the op-
tions by   or   button, and then press
 to increase the value, or   to de-
crease the value. In mid position, cursor is
displayed with one arrow.
To store the E ualizer settings, press   or
 button or directly press OK button on
Store option.
During the store process all the items are
stored, moreover, the User mode informa-
tion would not be lost. In other words, when
the user mode is selected again, after stor-
ing the Mode with one of the predefined op-
tions, the user defined fre uency values
would be set.
Settin AVL
 Using   or   button select AVL.
 Pressing   or   button will turn on and
off this feature.
Automatic Volume Limiting (Avl) function
normalises sound to obtain fixed output
level between programmes, having different
sound levels.
6RXQG
2Q
To Store the Settin s
 When the cursor is on any item which has
no sub-menu press OK button on the re-
mote control to store the settings directly.
or,
 Press  ,   or OK button on Store op-
tion to store Sound menu settings.
6RXQG
6WRUHG
Picture Menu
 To enter the Picture menu directly, press the
Green button, or
 Press "M" button, now you are in main
menu. In the Main menu, select Picture
using   or   button, then enter the Pic-
ture menu pressing   /   or OK but-
ton.
0HQX
Settin Bri htness
 As you enter the picture menu, Brightness
will be the first item.
 Press   button to increase brightness.
 Press   button to decrease brightness.
3LFWXUH
Settin Contrast
 Using   or   button select Contrast.
 Press   button to increase contrast level.
 Press   button to decrease contrast level.
2309W-ENG-1550UK (TOSHIBA UK)-17 INCH TFT.p65 13.05.2004, 18:5512

- 13 -
3LFWXUH
Settin Colour
 Using   or   button select Colour.
 Press   button to increase colour level.
 Press   button to decrease colour level.
3LFWXUH
Settin Sharpness
 Using   or   button select Sharpness.
 Press   button to increase sharpness
level.
 Press   button to decrease sharpness
level.
3LFWXUH
Settin Picture Mode:
 Using   or   button select Picture Mode.
 Press   or   button to set Picture Mode.
Picture Mode can be set to Auto, 4:3, 16:9,
Cinema, Subtitle, Zoom or Panorama.
3LFWXUH

Settin Noise Reduction
 Using   or   button select Noise Re-
duction.
 Press   or   button to select Noise Re-
duction level Off or Minimum or Me-
dium or Maximum then select store and
press   or   button to save your setting.
Note 1:
At low signal level, the changings on the Noise Reduction
function are not effective when there is menu on the
screen. If the menu is removed, the effect of this func-
tion is seen. At normal broadcasting, Noise Reduction
changings are effective at once.
Note 2:
At moving pictures, while Noise Reduction is at maxi-
mum level, some picture distortions may occur. If Noise
Reduction is set to medium or minimum, the picture will
improve.
3LFWXUH
0HGLXP
Settin Hue
(During Playback NTSC system, this will ap-
pear in AV mode only when NTSC video
source is applied. Otherwise, HUE option is
invisible in Picture menu.):
 Using   or   button select Hue.
 Press   button to increase hue level.
 Press   button to decrease hue level.
Center value is indicated with one arrow.
2309W-ENG-1550UK (TOSHIBA UK)-17 INCH TFT.p65 13.05.2004, 18:5513

- 14 -
3LFWXUH
To Store the Settin s
 When the cursor is on any item which has
no sub-menu press OK button on the re-
mote control to store the settings directly.
or,
 Press  ,   or OK button on Store op-
tion to store Picture menu settings.
3LFWXUH
6WRUHG
Feature Menu
 To enter the Feature menu directly, press the
Yellow button, or
 Press "M" button, now you are in main
menu. In the main menu, select Feature us-
ing   or   button. Then enter the Fea-
ture menu pressing   /   or OK but-
ton.
0HQX
Sleep Timer
As you enter the Feature menu, Sleep Timer
will be the first selected option. Use   or
 button to change the Sleep Timer val-
ues between Off, 0:15, 0:30, 0:45, 1:00,
1:15, 1:30, 1:45 and 2:00.
If sleep timer is activated it is displayed with
the TV status on the upper right of the
screen.

)HDWXUH
2II
After the setting time of sleep timer ended,
TV goes automatically to stand-by.
Child Lock
You can use this feature to prevent children
turning on/off TV or changing programmes
or adjustments etc. without remote control.
The Child Lock feature can be set On or Off
by   or   button. When Off is selected,
there will be no difference in the operation of
your TV. When On is selected, the TV can
only be controlled by the remote control
handset. In this case the control panel but-
tons except " " button on the right side of
the TV will not work.
)HDWXUH
2II
While Child Lock is On, pressing any of the
control panel buttons (except power on/off
button) causes the following warning menu
to appear on the screen.
&KLOG/RFN
2309W-ENG-1550UK (TOSHIBA UK)-17 INCH TFT.p65 13.05.2004, 18:5514

- 15 -
Selectin Menu Lan ua e
Menu language can be chosen by pressing
 or   button on Lan ua e item.
)HDWXUH
(QJOLVK
Av-2 Output
From Av-2 Output; TV, AV-1 or AV-3 can be
given. TV, AV-1 or AV-3 can be chosen by
pressing   or   button on "Av-2 Output".
)HDWXUH
79
PC Sound Mode
PC sound can be chosen by pressing  
or   button on PC Sound Mode item.
You can select sound that comes from TV,
AV-1, AV-2, AV-3 or PC to hear in PC mode.
)HDWXUH
3&
To Store Settin s
In Feature menu all settings are stored auto-
matically.
Installation Menu
 To enter the Installation menu directly, press
the Blue button, or
 Press "M" button, now you are in main
menu. In the main menu, select Install.
using   or   button. Then enter the In-
stall menu pressing   /   or OK but-
ton.
0HQX
When any item is selected with   or  
button in the install menu, the selected item
will be highlighted on the bottom bar.
Changes by pressing   or   button will
be result only at highlighted item on the bot-
tom bar.
Selectin Pro ramme
To select programme number, you can use
 or   button, Digit Buttons or The
Double Digit button with digit buttons.
,QVWDOO
3&&
Selectin Band
Band, can be chosen either,
 C or S by   or   button.
Selectin Channel
Channel can be changed by   or   but-
ton, by Digit Buttons or by the Double Digit
button with digit buttons.
2309W-ENG-1550UK (TOSHIBA UK)-17 INCH TFT.p65 13.05.2004, 18:5515

- 16 -
For band C,
01 - 17, 21 - 73,
For band S,
01 - 41.
Selectin Search
To start the search process, press   but-
ton for forward search or   button for back-
ward search. If a signal is found or reaches
to end of the band after searching, press
 or   buttons to continue search pro-
cess. To stop the search process when you
want, press   or   buttons again.
Selectin Fine Tunin
You can use the Fine Tuning process for
fine adjustment (after coarse adjustment), if
you are not happy about the image on the
screen.
Use   or   button on Fine Tunin item,
until getting the best image on the screen.
Normally the Fine Tuning cursor is placed
next to the left side on the slider and this is
indicated with one arrow.
Settin VCR ( Video Cassette Recorder )
Mode
 This item can be seen in TV, AV-1, AV-2, AV-3,
S-VIDEO modes.
 If you want to watch a VCR source from one
of these modes, then it will be better to set
VCR mode on. For this, while the cursor is
on this item press the   or   buttons to
set it On.
 If you want to watch a DVD , then you must
set this item off; because DVD is not a
source like a VCR and to see the picture
better, you must set the VCR mode Off.
To Store Settin s
 Press OK button on the remote control to
store the settings directly.
or,
 Press  ,   or OK button on Store op-
tion to store Install menu settings.
Installation menu in AV mode is as
follows.
,QVWDOO
21
Programme Menu
 To enter Programme menu directly, press
the " " button in TV mode, or
 Press "M" button, now you are in main
menu. In the main menu, select Pro ram.
using   or   button. Then enter the
Programme menu, press   /   or OK
button.
0HQX
Moving cursor to four direction you can reach
20 programmes in the same page. By
scrolling the pages up or down by pressing
the navigation buttons you can select all the
programmes in TV mode (except the AV
mode).
By cursor action, programme selection is
done automatically. In order to select
programme is also possible by using digit
or double-digit button. In this way program-
me selection gets also automatically. The
TV Status is changed by the programme se-
lection too. When using double-digit button
in order to select a programme, the
Programme Number in TV Status OSD is
displayed in "P --" form, and by pressing
digit buttons they are displayed in it.
Programme Number is between 00 and 99.
Programme Name has a name string with 4
characters. After autostore process the Pro-
gramme Names are set to:
2309W-ENG-1550UK (TOSHIBA UK)-17 INCH TFT.p65 13.05.2004, 18:5516

- 17 -
 Channel search "C-01" or "S-01" (band
and channel number) or name of the tuned
channel if defined.
3URJUDP3
1DPH
'HOHWH ,QVHUW $XWRVWRUH
At the bottom of the menu there is a pro-
gramme sort functions section. Each func-
tion is activated by color button (seen
above). Name allows changing the pro-
gramme name. By Delete you can delete
programmes that you decided. Insert sec-
tion is for inserting programmes into an-
other programme spaces. By selecting
Autostore section, Autostore menu will be
available.
Name:
To change the name of a decided program-
me, that programme is selected and
pressed to the Red button (Name). The first
letter begins to blink on the selected name.
To change that letter   or   button can
be used, and to select the other letters,  
or   button can be used. If the cursor is at
the last letter of the Programme Name,
pressing   button moves the cursor at the
beginning. On the contrary, if the cursor is at
the beginning of the Programme Name,
pressing   button moves the cursor at the
end.
After changing the name by pressing the
Red button (Store) it is stored. After
activating the name process the Insert,
Delete and Autostore processes will be
inactive and "Cancel" option will be valid.
This option cancels the name process, if the
new name do not want to be stored. To
cancel option is activated by pressing Blue
button.
&DQFHO
6WRUH
Insert:
When it is pressed to Green button (Insert),
"Name", "Autostore" and "Delete" functions
are erased, the selected programme (A) is
displayed with an arrow. From now on, the
automatic selection is canceled. With navi-
gation buttons, the decided programme
space (B) can be selected and by pressing
the green button again inserting is occurred
to that space (B).
Press Blue button to activate "Cancel" func-
tion of "Insert" process.
Delete:
For "Delete" process it is pressed to yellow
button, (Name, Insert and Autostore
functions are inactive). Pressing yellow but-
ton again erases the selected programme
from the programme list, and the
programmes below shift one up. Pressing
Blue button cancels the activated Delete
process.
Autostore:
To enter Autostore menu, press to the blue
button. To learn the features of this function
see "Autostore" below.
Autostore, searches and stores all channels
automatically on your TV, according to the
transmission of programme systems in
your area.
:DUQLQJ
&RXQWU\
&RQWLQXH
&DQFHO
$OO3UHVWRUHG3URJUDPPHV
:LOO%H(UDVHG
$36,V5XQQLQJ
3OHDVH:DLW
2309W-ENG-1550UK (TOSHIBA UK)-17 INCH TFT.p65 13.05.2004, 18:5517

- 18 -
First of all choose the Country by using
 or   button.
To cancel Autostore before starting, press
 button. To select Continue use   or
 button and press   or   button.
After Autostore is finalized, a programme list
will appear on the screen. In the programme
list you will see the programme numbers
and names assigned to the programmes.
If you do not accept the locations and/or the
programme names of programmes, you
can change them in Programme menu.
Source Menu
You can switch your TV to AV modes by
pressing directly to 
(;7
 button or by select-
ing in source menu from the main menu.
While in AV mode, you can also switch your
TV to TV or other AV modes by selecting in
source menu from the main menu.
0HQX
In main menu, firstly use   or   button
then use   /   or OK button to enter
Source menu. In source menu, move the
cursor by   or   button and then press
OK button or   or   buttons when the
cursor is on the re uired item. The selected
mode comes automatically on the screen.
79
$9
$9
$9
69,'(2
3&
Other Features
T Status
Pro ramme Number, Pro ramme Name
(or AV), (they are displayed on the upper left
of the screen) and Sleep Timer (shows the
time left on the upper right screen if en-
abled). The sound indicator and picture
mode are displayed with them too. They are
displayed after programme change during 3
seconds.
3
Programme Number
35
Programme Name (4 characters)
These OSDs are displayed when a new
programme is entered by digit button or by
pressing P<P, -P/CH, P/CH+,  ,

(;7
 or   button.
Programme Swap (P<P)
This button is used to reenter to the preced-
ing entered programme again. Pressing
"P<P" consecutively allows to swap into two
last entered programmes.





Double-digit (- / - -)
This OSD is displayed when the "Double-
Digit" button pressed in place of the pro-
gramme number indicator.
3
After then, in order to enter a programme it
must be pressed to two digit consecutively.
When it is late to press any digit button this
function will be ignored and the display will
be erased. In the same way it must not be
late to press any digit button after entering
the first digit. The limit of the delay time is 3
seconds.
2309W-ENG-1550UK (TOSHIBA UK)-17 INCH TFT.p65 13.05.2004, 18:5518

- 19 -
Personal Preferences (PP)
All the preset values will be restored, when
pressing "PP".
33
Sound Indicator
The alternatives of the indicator are Mono,
Stereo, Dual I and Dual II. This indicator is
displayed under the programme number in-
dicator on the screen. "I-II" button is used to
select Mono or Stereo, or Dual I or Dual II.
0212
In Mono broadcast or in forced-mono (for
stereo broadcast).
67(5(2
In Stereo broadcast.
'8$/,
If dual broadcast detected. Dual I is selected
in default and also can be selected after
Dual II by Remote Control.
'8$/,,
If Dual II selected by Remote Control.
,,

,


Picture Mode
Picture mode OSD is displayed when  
button is pressed. Picture mode can be
changed to Auto, 4:3, 16:9, Cinema, Sub-
title, Zoom or Panorama by pressing  
button.
Sleep Timer Indicator
It is displayed on the upper right of the
screen when a new programme is entered
by digit button or by pressing P<P, -P/CH,
P/CH+,  , 
(;7
 or   button. If sleep
timer is activated it is displayed with the TV
status and erased with it after 3 seconds.
In last minute, sleep timer indicator is dis-
played on the upper right of screen and
stays there until the TV goes automatically
to stand-by.

Mute Indicator
It is placed in the upper middle of the screen
when enabled, and it stays there until it is
disabled.
To cancel mute, there is two alternative; the
first one is pressing to " " button, this vol-
ume is set to the preceding value, and the
second one is increasing the volume level,
thus it starts at the minimum level to in-
crease. By decreasing the volume level in
mute state, mute will not be ignored, only the
volume level will decrease. If mute canceled
after decreasing the volume level, the vol-
ume will valid with the decreased level.
No-Signal Detection (T )
If no valid signal detected, it takes 5 minutes
for the switching to the Stand-By mode un-
less any signal detected or no any Remote
Control command is accessed.
After a Remote Control command (if No-Sig-
nal Timer is active) the timer stops and if no
signal detected again the timer is initialized
to 5 minutes and starts 3 seconds later
again to count down.
It is not valid in AV mode.

No-Signal Detection (PC)
If no valid signal detected for 5 minutes sys-
tem goes to Stand-By mode. To switch on
the system press   button.
As the last status feature, system starts from
TV or PC, whichever was the status before
stand-by or switch-off. Note that SCART in-
puts have the precedence on both TV and
PC.
2309W-ENG-1550UK (TOSHIBA UK)-17 INCH TFT.p65 13.05.2004, 18:5519